Molecular Weight Distribution Research Articles

Lignocellulosic biomass to glycols: Simultaneous conversion of cellulose, hemicellulose and lignin using an organic solvent

This study investigates the simultaneous conversion of holocellulose and lignin fractions during the catalytic hydrogenolysis of biomass to glycols, focusing on how different organic solvents, necessary to keep the lignin soluble, impact the conversion of non-delignified and deashed biomass, as well as the ethylene glycol production and lignin behavior. Although the catalyst amounts used were low, the cellulose and hemicellulose were converted into ethylene glycol, propylene glycol, sugar alcohols, and glycerol, yielding about 40 wt%. This is slightly lower than the benchmark process (acidified water and de-ashed biomass), which had a total yield of around 50 wt%. A noticeable difference between using organic solvents and water was found in the behavior of depolymerized lignin. When using an organic solvent, up to 63 % of the lignin could be extracted from the biomass and kept soluble, compared to only 15 % when using acidified water. The molecular weight distribution of solubilized lignin was similar for all organic solvents (Mw = 833–1190 g/mol), but it was significantly different from the benchmark experiment with acidified water (Mw = 423 g/mol).

Polyacrylate epoxide oligomers with robust photo‐crosslinked and thermomechanical properties enabled by controlling copolymerizing molecular weight distribution

AbstractPhoto‐triggering curing coatings have advantages of improving production efficiency, reducing pollution emissions, and contributing to green environmental protection. However, making the trade‐off between appropriate viscosity and UV‐curing properties in a high‐performing polymer system remains a formidable challenge. In this paper, firstly, a series of acrylate copolymer oligomers (named as PAAR) were synthesized using methyl methacrylate (MMA), butyl acrylate (BA), and glycidyl methacrylate (GMA), then methacrylic acid (MAA) was grafted utilizing the reaction between carboxyl group in MAA with epoxy group in oligomer to introduce double bonds. By adjusting the oligomer molecular weight to control the viscosity and changing the GMA ratio to obtain suitable double bonds content. As a result, the number molecular weight (Mn) of the thus‐obtained PAAR oligomers were less than 3000 Da, and the polymer dispersity indexes (PDI) were lower than 1.8. Photo‐polymerization kinetics revealed that the coating prepared using the oligomers could be fully cross‐linked by UV light triggering within 60 s, achieving a high transparency of 90% along with favorable thermal and mechanical properties. Furthermore, it was confirmed that the water resistance on the surface of the cured films and hydrophobicity were more influenced by the presence of hydroxyl groups.

Fingerprint profiling for quality evaluation and the related biological activity analysis of polysaccharides from Liuweizhiji Gegen-Sangshen beverage

IntroductionLiuweizhiji Gegen-Sangshen beverage (LGS) is popular in China, which has been used for alleviating alcohol-mediated discomfort and preventing alcoholic liver disease (ALD). This beverage is consisted of six herbal components that are known as functional foods and fruits. LGS is rich in polysaccharides, however, the activity and quality evaluation of LGS-derived polysaccharides remain unexplored. The purpose of this study is thus to establish a comprehensive quality control methodology for the assessment of LGS polysaccharides (LGSP) and to further explore the anti-oxidant, anti-inflammatory as well as prebiotic effect of LGSP.MethodsLGSP was extracted, followed by analysis of molecular weight distribution, monosaccharide content and structural characterization via integrating the application of high-performance size exclusion chromatography (HPSEC), 1-phenyl-3-methyl-5-pyrazolone-HPLC (PMP-HPLC), fourier transform infrared spectroscopy (FT-IR) as well as nuclear magnetic resonance spectroscopy (NMR) techniques. The anti-oxidation activity of LGSP was determined by DPPH, ABTS, hydroxyl radical scavenging capacity and total antioxidant capacity. The anti-inflammation of LGSP were assessed on the RAW 264.7 cells. The effect of LGSP on growth of Lactobacillus, Bifidobacterium bifidum and Bifidobacterium adolescentis was evaluated.ResultsThe results demonstrated that LGSP had two molecular weight distribution peaks, with the average molecular weights of (6.569 ± 0.12) × 104 Da and (4.641 ± 0.30) × 104 Da. LGSP was composed of 8 monosaccharides, with galacturonic acid, glucose rhamnose and galactose representing the highest molar ratios. Homogalacturonic acid (HG) type and rhamnosegalacturonic acid glycans I (RG-I) type and α-1,4-glucan were present in LGSP. LGSP concentration in LGS was 17.94 ± 0.28 mg/mL. Furthermore, fingerprint analysis combined with composition quantification of 10 batches of LGSP demonstrated that there was a high similarity among batches. Notably, LGSP exhibited anti-oxidant effect and inhibited expressions of pro-inflammatory factors (TNF-α and IL-6) in LPS-stimulated RAW 264.7 cells. In addition, LGSP remarkably promoted the proliferation of probiotics Lactobacillus, Bifidobacterium bifidum and Bifidobacterium adolescentis, showing good prebiotic activity.DiscussionThe results of present study would be of help to gain the understanding of structure–activity relationship of LGSP, provide a reference for quality evaluation of bioactive LGSP, and facilitate development of unique health and functional products in the future.

Embedding Bioprinting of Low Viscous, Photopolymerizable Blood-Based Bioinks in a Crystal Self-Healing Transparent Supporting Bath.

Protein-based hydrogels have great potential to be used as bioinks for biofabrication-driven tissue regeneration strategies due to their innate bioactivity. Nevertheless, their use as bioinks in conventional 3D bioprinting is impaired due to their intrinsic low viscosity. Using embedding bioprinting, a liquid bioink is printed within a support that physically holds the patterned filament. Inspired by the recognized microencapsulation technique complex coacervation, crystal self-healing embedding bioprinting (CLADDING) is introduced based on a highly transparent crystal supporting bath. The suitability of distinct classes of gelatins is evaluated (i.e., molecular weight distribution, isoelectric point, and ionic content), as well as the formation of gelatin-gum arabic microparticles as a function of pH, temperature, solvent, and mass ratios. Characterizing and controlling this parametric window resulted in high yields of support bath with ideal self-healing properties for interaction with protein-based bioinks. This support bath achieved transparency, which boosted light permeation within the bath. Bioprinted constructs fully composed of platelet lysates encapsulating a co-culture of human mesenchymal stromal cells and endothelial cells are obtained, demonstrating a high-dense cellular network with excellent cell viability and stability over a month. CLADDING broadens the spectrum of photocrosslinkable materials with extremely low viscosity that can now be bioprinted with sensitive cells without any additional support.

Greener solvents for the processing of preceramic polycarbosilane: application in the preparation of B4C/SiC composites.

The innovation introduced in this study consists of replacing toluene with safer solvents such as cyclopentane or diethyl ether in the processing of a preceramic polycarbosilane (allylhydridopolycarbosilane, AHPCS) and assessing its impact on the functionalisation of B4C powders to produce B4C/SiC composites. Fourier-transform infrared (FT-IR) with ATR and nuclear magnetic resonance (NMR) spectroscopy revealed no major modification in the polymer structure. SEC/MALS analysis showed a slight change in the number-average molar mass of the polymer regardless of the functionalisation solvent used in correlation with a slight decrease in the polymer ceramic yield due to oligomer loss. The thermal behaviour of the preceramic polymer investigated via mass spectrometry remained unaffected by the solvent change. The search for polymer residues after distillation highlighted the recyclability of both the functionalisation solvent and the polymer, despite a slight increase in the molar mass of the polymer. Finally, the sinterability of B4C/AHPCS samples was studied with the preparation of B4C/SiC composites via a polymer-derived ceramic (PDC) route and spark plasma sintering (SPS). The effect of the solvent on the microstructure and relative density of the specimens (>92%) is negligible. The specimens retain a fine and homogeneous phase distribution despite process modification. The results highlight the approach developed to use greener solvents for the chemical synthesis of functionalised ceramics and represent a step towards the generalisation of more environmentally friendly processes.

Evaluation of the environmental and economic scope of an electrocoagulation process for the treatment of wastewater from the instant coffee industry

AbstractIn this study, an industrial wastewater from instant coffee production was treated by electrocoagulation (EC). The effect of various EC operating parameters, such as electrode type, current density, support electrolyte concentration and stirring velocity, were investigated to determine the optimal operating EC conditions. The scope of electrocoagulation (EC) was assessed, in environmental and economic terms, for the treatment of industrial wastewater originated from the production of instant coffee. The evaluation included the effect of EC operating factors (electrode type, current density, supporting electrolyte concentration and stirring velocity) on Color removal, COD and TOC degradation, toxicity, molecular weight distribution, as well as the total operating cost. The following optimal operating conditions were established through a series of preliminary experiments, a Box-Behnken design of experiments, Response Surface Methodology application, and multi-objective optimization analysis: the pair of Fe (anode)-stainless steel (cathode) electrodes, supporting electrolyte = 1.78 g of NaCl/L; current density = 150 A/m2; electrode gap = 3 mm; stirring velocity = 350 RPM; and pH0 = 4.7 (that of raw industrial effluent). Finally, the kinetic study allowed defining the electrolysis operation time of ca. 180 min required to comply with the maximum permissible discharge limits for the production of instant coffee the discharge of soluble coffee effluents, in terms of COD concentration, established by current Colombian legislation. The EC reached ca. 97% decolorization, as well as 72% and 65% of COD and TOC removal degradation, respectively, with total operating costs of 6.26 USD/m3. This yielded an oxidized (COS = 2.87), biocompatible (BOD5/COD = 0.437) and non-toxic effluent, free of contaminants with molecular weight > 30 kDa. The EC appeared as an effective alternative for the treatment of industrial wastewater from the production of instant coffee within the framework of different Sustainable Development Goals (number 6 (Clean water and sanitation), number 7 (Clean and affordable energy), number 9 (Industry, innovation and infrastructure) and 13 (Climate action)).

Three anti-inflammatory polysaccharides from Lonicera japonica Thunb.: Insights into the structure-function relationships

This study demonstrates the feasibility of producing three polysaccharides (neutral LJP-1, acidic LJP-2 and acidic LJP-3) with significant in vitro and in vivo anti-inflammatory activities from the flowers of Lonicera japonica. The three polysaccharides differed in chemical composition, molecular weight distribution, glycosidic linkage pattern, functional groups and morphology. They exhibited excellent protective effects (in a dose-dependent manner) in lipopolysaccharide-injured RAW264.7 macrophages and CuSO4-damaged zebrafish via reducing NO production and inhibiting the overexpressions of inflammation-related transcription factors, inflammatory proteins and cytokines in the NF-κB/MAPK signaling pathways. Their anti-inflammatory effects varied owing to their different molecular characteristics and chemical compositions. Overall, LJP-2 at 400μg/mL was the most effective. LJP-2 consisted mainly of → 5)-α-L-Araf (1→, →4)-α-L-GalpA (1→ and →2)-α-L-Rhap (1→ residues with terminal T-β-D-Glcp. Thus, honeysuckle flowers are good sources of anti-inflammatory polysaccharides, and precise fractionation enables the production of potent anti-inflammatory agents for the development of functional foods and healthcare products.

Impact of the unimodal molar mass distribution on the mechanical behavior of polymer nanocomposites below the glass transition temperature: A generic, coarse-grained molecular dynamics study

Polymer nanocomposites (PNCs) have shown great potential to meet the ever-growing requirements of modern engineering applications. Nowadays, molecular dynamics (MD) simulations are increasingly employed to complement experimental work and thereby gain a deeper understanding of the complex structure–property relations of PNCs. However, with respect to the thermoplastic’s mechanical behavior, the role of its average molar mass M¯n is rarely addressed, and many MD studies only consider uniform (monodispersed) polymers. Therefore, this contribution investigates the impact that M¯n and the dispersity Đ have on the stiffness and strength of PNCs through coarse-grained MD. To this end, we employed a Kremer–Grest bead–spring model and observed the expected increase in the mechanical performance of the neat polymer for larger M¯n. Our results indicated that the unimodal molar mass distribution does not impact the mechanical behavior in the investigated dispersity range 1.0≤Đ≤1.09. For the PNC, we obtained the same M¯n-dependence and Đ-independence of the mechanical properties over a wide range of filler sizes and contents. This contribution proves that even simple MD models can reproduce the experimentally well researched effect of the molar mass. Hence, this work is an important step in understanding the complex structure–property relations of PNCs, which is essential to unlock their full potential.

Unlocking the potential of supramolecular polymers with bimodal molecular weights for instant and strong underwater adhesion

Developing adhesives suitable for underwater environments remains a formidable challenge due to the barrier presented by water, hindering contact between the adhesive and adherend. In this work, supramolecular adhesives prepared by mixing low and high molecular weight poly(butyl acrylate)-based copolymers are manifested to function effectively for underwater adhesion regardless of substrates’ affinity to water. Optimization of adhesion performance is achieved by manipulating the copolymer composition, resulting in the remarkable adhesion strengths of 1290 N/m and 1047 N/m to hydrophobic PET and hydrophilic glass substrates, respectively. The observed high underwater adhesion is attributed to a synergistic effect: instant and efficient removal of the hydration layer facilitated by the low molecular weight polymer strands, and mechanical resilience conferred by the high molecular weight strands featured by chain entanglements. Adequate interfacial interactions are attained by the supramolecular interactions including cation-π and π-π bonding. Notably, owing to its inherent hydrophobicity, the adhesive can be stored underwater for over a week and still displays 842 N/m peel strength to glass substrate. This work unlocks the potential of supramolecular adhesives with bimodal molecular weight distribution for instant and strong underwater adhesion, providing a straightforward yet scalable strategy to produce high-performance underwater adhesives.

Fractionation and refining of pectic oligosaccharides derived from onion skins through continuous feed diafiltration

In this work, a diafiltration-based process was investigated for the recovery of pectic oligosaccharides produced by subcritical water hydrolysis from onion skin waste. Four tubular ceramic membranes from 100 to 1 kDa were selected based on the molecular weight of the different galacturonic acid species present in the onion skin hydrolysate. All these membranes showed high selectivity towards pectic oligosaccharides, with low retention for free galacturonic acid, monosaccharides, organic acids, and other impurities. The 50 and 100 kDa membranes completely retained pectic oligosaccharides with a molecular weight exceeding 80 kDa, accounting for approximately 30 % of the initial pectic oligosaccharides in the hydrolysate. However, the purification rate was significantly slower using the 50 kDa membrane due to the increased cake layer resistance. Furthermore, it was examined a fractionation/purification cascade involving sequential diafiltration stages using 100, 10, and 1 kDa membranes at 25 °C, TMP = 1 bar, and a crossflow velocity of 1.5 m s−1. Approximately 87 % of the initial pectic oligosaccharides were successfully recovered and purified in the retentates, highlighting their potential for diverse applications due to their narrow molecular weight distribution, while phenolic compounds and other valuable low molecular weight molecules were recovered in the final permeate.

Unlocking the potential of supramolecular polymers with bimodal molecular weights for instant and strong underwater adhesion

Developing adhesives suitable for underwater environments remains a formidable challenge due to the barrier presented by water, hindering contact between the adhesive and adherend. In this work, supramolecular adhesives prepared by mixing low and high molecular weight poly(butyl acrylate)-based copolymers are manifested to function effectively for underwater adhesion regardless of substrates’ affinity to water. Optimization of adhesion performance is achieved by manipulating the copolymer composition, resulting in the remarkable adhesion strengths of 1290 N m-1 and 1047 N m-1 to hydrophobic PET and hydrophilic glass substrates, respectively. The observed high underwater adhesion is attributed to a synergistic effect: instant and efficient removal of the hydration layer facilitated by the low molecular weight polymer strands, and mechanical resilience conferred by the high molecular weight strands featured by chain entanglements. Adequate interfacial interactions are attained by the supramolecular interactions including cation-π and π-π bonding. Notably, owing to its inherent hydrophobicity, the adhesive can be stored underwater for over a week and still displays 842 N m-1 peel strength to glass substrate. This work unlocks the potential of supramolecular adhesives with bimodal molecular weight distribution for instant and strong underwater adhesion, providing a straightforward yet scalable strategy to produce high-performance underwater adhesives.

Well-defined triphenylamine-containing polymers as hole-transporting layers in solution-processable organic light-emitting diodes via living anionic polymerization

In this study, we conducted anionic polymerization of N-[1,1′-biphenyl]-4-yl-N-(4′-ethenyl[1,1′-biphenyl]-4-yl)-9,9-dimethyl-9H-fluoren-2-amine (A) incorporating a triphenylamine group as a hole-transporting unit using sec-butyllithium and potassium naphthalenide as initiators in tetrahydrofuran at −30 ℃ for 10 min. The resultant poly(A)s exhibited controlled molecular weights (Mn = 20.9−126.3 kg/mol) and narrow molecular weight distributions (Mw/Mn ≤ 1.12). The living nature of the propagating chain end of poly(A) was confirmed by postpolymerization. Additionally, block copolymerization of A with styrene (St) and 2-vinylpyridine (2VP) was performed to assess its relative reactivity. Copolymerization resulted in the precise synthesis of well-defined block copolymers with poly(A) segments. Thermal properties of poly(A) were investigated using thermogravimetric analysis and differential scanning calorimetry. Notably, the thermal annealing of poly(A) film at 230 ℃ for 10 min made it insoluble in toluene, indicating its solvent resistance. Thus, poly(A) was used as the hole-transporting layer (HTL) in solution-processable organic light-emitting diodes (OLEDs). A comparative analysis against a reference device containing poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) revealed an enhancement in the performance of the OLED comprising thermally annealed poly(A) as the HTL. These results strongly suggest that poly(A) is a promising HTL material for solution-processable OLEDs.

Euglena gracilis Protein: Effects of Different Acidic and Alkaline Environments on Structural Characteristics and Functional Properties.

Due to the growing demand for human-edible protein sources, microalgae are recognized as an economically viable alternative source of proteins. The investigation into the structural characteristics and functional properties of microalgin is highly significant for its potential application in the food industry as an alternative source of protein. In this research, we extracted protein from Euglena gracilis by using alkaline extraction and acid precipitation and investigated its structural characteristics and functional properties in different acidic and alkaline environments. The molecular weight distribution of Euglena gracilis protein (EGP), as revealed by the size exclusion chromatography results, ranges from 152 to 5.7 kDa. EGP was found to be rich in hydrophobic amino acids and essential amino acids. Fourier infrared analysis revealed that EGP exhibited higher α-helix structure content and lower β-sheet structure content in alkaline environments compared with acidic ones. EGP exhibited higher foaming properties, emulsifying activity index, solubility, free sulfhydryl, and total sulfhydryl in pH environments far from its isoelectric point, and lower fluorescence intensity (2325 A.U.), lower surface hydrophobicity, larger average particle size (25.13 µm), higher emulsifying stability index, and water-holding capacity in pH environments near its isoelectric point. In addition, X-ray diffraction (XRD) patterns indicated that different acidic and alkaline environments lead to reductions in the crystal size and crystallinity of EGP. EGP exhibited high denaturation temperature (Td; 99.32 °C) and high enthalpy (ΔH; 146.33 J/g) at pH 11.0, as shown by the differential scanning calorimetry (DSC) results. The findings from our studies on EGP in different acidic and alkaline environments provide a data basis for its potential commercial utilization as a food ingredient in products such as emulsions, gels, and foams.

Genome-wide screening and characterization of phospholipase A (PLA)-like genes in sorghum (Sorghum bicolor L.).

The characterisation of PLA genes in the sorghum genome using in-silico methods revealed their essential roles in cellular processes, providing a foundation for further detailed studies. Sorghum bicolor (L.) Moench is the fifth most cultivated crop worldwide, and it is used in many ways, but it has always gained less popularity due to the yield, pest, and environmental constraints. Improving genetic background and developing better varieties is crucial for better sorghum production in semi-arid tropical regions. This study focuses on the phospholipase A (PLA) family within sorghum, comprehensively characterising PLA genes and their expression across different tissues. The investigation identified 32 PLA genes in the sorghum genome, offering insights into their chromosomal localization, molecular weight, isoelectric point, and subcellular distribution through bioinformatics tools. PLA-like family genes are classified into three groups, namely patatin-related phospholipase A (pPLA), phospholipase A1 (PLA1), and phospholipase A2 (PLA2). In-silico chromosome localization studies revealed that these genes are unevenly distributed in the sorghum genome. Cis-motif analysis revealed the presence of several developmental, tissue and hormone-specific elements in the promoter regions of the PLA genes. Expression studies in different tissues such as leaf, root, seedling, mature seed, immature seed, anther, and pollen showed differential expression patterns. Taken together, genome-wide analysis studies of PLA genes provide a better understanding and critical role of this gene family considering the metabolic processes involved in plant growth, defence and stress response.

Molecular Weight Distribution of Humic Acids Isolated from Calcic Cryosol in Central Yakutia, Russia.

The transition of soils into fallow state has a significant impact on the accumulation and transformation of soil organic matter (SOM). However, the issue of SOM transformation as a result of soil transition to fallow state in cryolithozone conditions is insufficiently studied. The aim of this study is to investigate the molecular weight (MW) distribution of humic acids (HAs) isolated from soils of central Yakutia. Native, fallow and agricultural soils in the vicinity of Yakutsk city were studied. MW distributions of HA preparations were obtained on an AKTAbasic 10 UPS chromatographic system (Amersam Biosciences, Uppsala, Sweden) using a SuperdexTM 200 10/300 GL column (with cross-linked dextran gel, fractionation range for globular proteins 10-600 kDa). The data on the molecular-mass distribution of HAs of fallow and agricultural soils of Central Yakutia were obtained for the first time. According to the obtained data, it was found that the highest carbon content in the structure of HAs was observed in agricultural soils (52.56%), and is associated with soil cultivation and fertilizer application. Among the HAs of fallow soils, we note that those soils that are in the process of self-vegetation have a relatively high carbon content in the HAs (45.84%), but the highest content was observed in fallow soils used as hayfields (49.98%), indicating that the reinvolvement of agriculture in fallow soils leads to an increase in the carbon content of HAs. According to the data of the MW distribution of HAs, it was found that the highest content of a high MW fraction of HAs was recorded in native soil (18.8%); this is due to the early stages of humification and the low maturity of organic matter. The highest content of a low MW fraction of HAs was recorded in agricultural soil (73.3%); this is due to the formation of molecular complexes of a "secondary" nature, which are more stable in the environment than the primary transformation products of humification precursors. The molecular composition of the HAs of fallow soils in the process of self-overgrowing is characterized by values closer to the HAs of native soils, which indicates their transformation towards HAs of native soils. The obtained results indicate that the reinvolvement of fallow soils leads to the transformation of the molecular composition of HAs towards HAs of agricultural soils, and to an increase in the resistance of SOM to biodegradation.

Leveraging Electron Push-Pull Effect for Catalytic Polymerization and Degradation of a Cyclobutane Monomer System.

Ring-opening polymerization (ROP) offers a striking solution to solve problems encountered in step-growth condensation polymerization, including precise control over molecular weight, molecular weight distribution, and topology. This has inspired our interest in ROP of cycloalkanes with an ultimate goal to rethink polyolefins, which clearly poses a number of challenges. Practicality of ROP of cycloalkanes is actually limited by their low polymerizability and elusive mechanisms which arise from significantly varied ring size and non-polar C-C bonds in monomers. In this work, by using Lewis acid/Brønsted base/C(sp3)-H initiator system previously developed in our laboratory, we focus on cyclobutanes and explore the positional and electronic effects of substituents on the ring, namely electron push-pull effect, in promoting controlled polymerization to afford densely functionalized poly(cyclobutanes), as well as catalytic degradation of obtained polymers for upcycling. More importantly, experiments and DFT calculations unveil considerable population of Lewis-acid-induced thermostabilized 1,4-zwitterions, which distinguish cyclobutanes from cyclopropanes and others. All these findings would shed light on catalytic synthesis and degradation of saturated all-carbon main-chain polymers, as well as small molecule transformations of cyclobutanes.

Leveraging Electron Push‐Pull Effect for Catalytic Polymerization and Degradation of a Cyclobutane Monomer System

AbstractRing‐opening polymerization (ROP) offers a striking solution to solve problems encountered in step‐growth condensation polymerization, including precise control over molecular weight, molecular weight distribution, and topology. This has inspired our interest in ROP of cycloalkanes with an ultimate goal to rethink polyolefins, which clearly poses a number of challenges. Practicality of ROP of cycloalkanes is actually limited by their low polymerizability and elusive mechanisms which arise from significantly varied ring size and non‐polar C−C bonds in monomers. In this work, by using Lewis acid/Brønsted base/C(sp3)‐H initiator system previously developed in our laboratory, we focus on cyclobutanes and explore the positional and electronic effects of substituents on the ring, namely electron push‐pull effect, in promoting controlled polymerization to afford densely functionalized poly(cyclobutanes), as well as catalytic degradation of obtained polymers for upcycling. More importantly, experiments and DFT calculations unveil considerable population of Lewis‐acid‐induced thermostabilized 1,4‐zwitterions, which distinguish cyclobutanes from cyclopropanes and others. All these findings would shed light on catalytic synthesis and degradation of saturated all‐carbon main‐chain polymers, as well as small molecule transformations of cyclobutanes.

Highly efficient dual photoredox/copper catalyzed atom transfer radical polymerization achieved through mechanism-driven photocatalyst design

Atom transfer radical polymerization (ATRP) with dual photoredox/copper catalysis combines the advantages of photo-ATRP and photoredox-mediated ATRP, utilizing visible light and ensuring broad monomer scope and solvent compatibility while minimizing side reactions. Despite its popularity, challenges include high photocatalyst (PC) loadings (10 to 1000 ppm), requiring additional purification and increasing costs. In this study, we discover a PC that functions at the sub-ppm level for ATRP through mechanism-driven PC design. Through studying polymerization mechanisms, we find that the efficient polymerizations are driven by PCs whose ground state oxidation potential—responsible for PC regeneration—play a more important role than their excited state reducing power, responsible for initiation. This is verified by screening PCs with varying redox potentials and triplet excited state generation capabilities. Based on these findings, we identify a highly efficient PC, 4DCDP-IPN, featuring moderate excited state reducing power and a maximized ground state oxidation potential. Employing this PC at 50 ppb, we synthesize poly(methyl methacrylate) with high conversion, narrow molecular weight distribution, and high chain-end fidelity. This system exhibits oxygen tolerance and supports large-scale reactions under ambient conditions. Our findings, driven by the systematic PC design, offer meaningful insights for controlled radical polymerizations and metallaphotoredox-mediated syntheses beyond ATRP.

Encapsulation of organic ultraviolet photoprotective actives into poly(methyl methacrylate) nanoparticles for sunscreen formulations

AbstractSkin cancer is the most common of all cancers worldwide. This way, it is mandatory to adopt an adequate sun protection routine, including sunscreen lotions. However, despite the proven effectiveness of numerous chemical filters, many of them are also known for their allergenic and carcinogenic potential effects, which can be mitigated by exploring some encapsulation routes. Thus, the present work evaluates the influence of seven distinct ultraviolet (UV) organic filters on the final particle size and molecular weight distributions of poly(methyl methacrylate) (PMMA) beads. Moreover, the sun protection factors (SPF) of the loaded nanoparticles are also evaluated when used for preparation of sunscreen formulations. The UV filters did not affect the course of MMA miniemulsion polymerizations significantly, enabling the synthesis of loaded nanoparticles. Nevertheless, adding the filters shifted the particle size distributions toward larger diameters, which are appropriate for cosmetic formulations. Based on the SPF analyses, it was also possible to observe a 12‐fold increase in the SPF values of the prepared formulations and an increase in the critical wavelength. Therefore, the in situ incorporation of distinct UV filters during miniemulsion MMA polymerizations constitutes a robust and versatile technology to produce PMMA nanoparticles loaded with UV filters for preparation of sunscreen formulations.

Understanding the Ecological Robustness and Adaptability of the Gut Microbiome in Plastic-Degrading Superworms (Zophobas atratus) in Response to Microplastics and Antibiotics.

Recent discoveries indicate that several insect larvae are capable of ingesting and biodegrading plastics rapidly and symbiotically, but the ecological adaptability of the larval gut microbiome to microplastics (MPs) remains unclear. Here, we described the gut microbiome assemblage and MP biodegradation of superworms (Zophobas atratus larvae) fed MPs of five major petroleum-based polymers (polyethylene, polypropylene, polystyrene, polyvinyl chloride, and polyethylene terephthalate) and antibiotics. The shift of molecular weight distribution, characteristic peaks of C═O, and metabolic intermediates of residual polymers in egested frass proved depolymerization and biodegradation of all MPs tested in the larval intestines, even under antibiotic suppression. Superworms showed a wide adaptation to the digestion of the five polymer MPs. Antibiotic suppression negatively influenced the survival rate and plastic depolymerization patterns. The larval gut microbiomes differed from those fed MPs and antibiotics, indicating that antibiotic supplementation substantially shaped the gut microbiome composition. The larval gut microbiomes fed MPs had higher network complexity and stability than those fed MPs and antibiotics, suggesting that the ecological robustness of the gut microbiomes ensured the functional adaptability of larvae to different MPs. In addition, Mantel's test indicated that the gut microbiome assemblage was obviously related to the polymer type, the plastic degradability, antibiotic stress, and larval survival rate. This finding provided novel insights into the self-adaptation of the gut microbiome of superworms in response to different MPs.