Model Of Knee Joint Research Articles

Statistical Shape Modeling to Determine Poromechanics of the Human Knee Joint.

Subject-specific knee joint models are widely used to predict joint contact mechanics for individuals but may not capture the variance in knee joint geometry across a population. Statistical shape modeling uses the dataset of a cohort to encapsulate population-wide variability. The present study aimed to develop a shape modeling procedure for poromechanical finite element models of knee joint to account for population diversity in the creep response of knees. Shape models of right knee joints were created from MRI of 31 healthy male subjects using principal component analysis. Creep analysis was performed for 13 shape models in total, i.e., the average model, plus six models for both the first and second principal modes. For a given loading, the contact and fluid pressures varied substantially within these mathematically produced models but compared reasonably well to that of three subject-specific models that were constructed from individual knees, representing approximately the smallest, median and largest knees of the 31 right knees. While the joint size variation, generally represented by the first principal component, predominantly influenced the magnitudes of contact and fluid pressures, the joint shape variation characterized by the second principal component further affected the pressure distribution, and load sharing between the lateral and medial compartments. The present study evaluated a workflow for the statistical shape modeling of poromechanical behavior of knee joints with sample results based on a small population. However, the workflow can be readily used for a large population to address the challenge of interpatient variability in joint contact mechanics, particularly in contact and fluid pressures in articular cartilage, and variable creep behaviors of the joint associated with individual anatomical variations.

Biomechanical impact of progressive meniscal extrusion on the knee joint: a finite element analysis

BackgroundWhile measuring meniscal extrusion quantitatively is an early risk factor for knee osteoarthritis (KOA), the biomechanics involved in this process are not well understood. This study aimed to investigate the effects of varying degrees of medial and lateral meniscal extrusion and their material softening on knee osteoarthritis progression.MethodsFinite element analysis (FEA) was utilized to simulate varying degrees of meniscal extrusion (1–5 mm) in 72 knee joint models, representing progressive meniscal degeneration and material softening due to injury. Changes in von Mises stress of the cartilage and menisci and the load distribution on the tibial plateau’s meniscus and cartilage were studied under balanced standing posture in both healthy and injured knees, and statistical analysis was performed using Spearman correlation.ResultsCompared to healthy knees, peak stress in medial compartment tissues increased by over 40% with 4 mm of medial meniscus extrusion, and in lateral compartment tissues with 2 mm of lateral meniscus extrusion. Meniscus extrusion reduced the contact load between the meniscus and femoral cartilage but increased it between the tibial and femoral cartilages, with a maximum increase up to fivefold. Spearman correlation analysis indicated that meniscal extrusion significantly affected peak stress and contact loads in the respective knee compartment (p < 0.001), with a lesser impact on the opposite compartment. Notably, medial meniscal extrusion also significantly increased peak stress in the lateral tibial cartilage (p < 0.05).ConclusionsThe quantitative analysis revealed that meniscal extrusion significantly affected the biomechanics of soft tissues within the same compartment, with limited impact on the opposite side. Specifically, Medial extrusion beyond 4 mm significantly affected the biomechanics of the medial compartment, while lateral extrusion over 2 mm had a similar impact on the lateral compartment. Meniscal softening, without altering joint contact characteristics, primarily affected the biomechanics of the meniscus itself, with minimal impact on other soft tissues.

Finite element simulation of knee joint pressure and surface displacement: relationship and influencing factors

Knee sleeves are widely used functional pressure garments that exert pressure on the knee, causing body surface displacement and deformation. Understanding the relationship between knee joint pressure distribution and body surface displacement, along with the factors affecting this displacement, is crucial for optimizing knee sleeves. This study established a biomechanical model of the human knee joint using three-dimensional reconstruction and finite element analysis. The study simulated the pressure distribution and body surface displacement after wearing five different knee sleeve designs. Using SPSS software, it analyzed clothing and human factors to determine the main influences on displacement, resulting in linear regression equations linking knee physiological characteristics and skin displacement. Findings indicated that skin curvature radius and the distance between skin and bone significantly affect displacement, while knee sleeve structure design shows less correlation. The study also divided the knee joint into eight sections to calculate volume shrinkage after compression, providing insights for designing knee sleeves that enhance comfort and functionality based on human physiology.

Finite-element simulation of functional knee sleeves based on three-dimensional modeling of the knee joint

Knee sleeves are one of the most satisfying and widely used items of protective equipment for sports enthusiasts. Achieving an effective balance between functionality and comfort is a key factor in the design of knee sleeves. However, there are still some problems with the knee protection products currently on the market, such as poor thermal and moisture comfort, difficulty in putting on and taking off, slippage during doing sports, and the lack of a timely and effective feedback mechanism that cannot guide the user to actively adjust their movement posture to avoid sports injuries. To improve the function and pressure comfort of the human body after wearing knee sleeves, this study took the knee joint as the research object, established a three-dimensional knee joint model through computed tomography (CT) scanning and Mimics software, and then built a finite-element model under the contact state between the human body and pressure clothing on this basis. Moreover, ABAQUS was used for finite-element simulation to obtain the pressure and displacement distribution of knee joints after wearing knee sleeves. In order to further investigate the stress state and deformation trend of knee joint after wearing knee sleeves, each section of the human body at the knee joint was divided into four regions according to the angle, and the functional relationship between pressure and displacement was obtained by curve fitting. This study has significance for the investigation of the pressure comfort threshold of knee sleeves and the optimization of the design of functional knee sleeves.

A MnO2 nanosheets doping double crosslinked hydrogel for cartilage defect repair through alleviating inflammation and guiding chondrogenic differentiation

The inflammatory microenvironment and inferior chondrogenesis are major symptoms after cartilage defect. Although various modifications strategies associated with hydrogels exhibit remarkable capacity of pro-cartilage regeneration, the adverse effect by prolonging inflammation is still formidable to hamper potential biomedical applications of different hydrogel implants. Herein, inspired by the repair microenvironment of articular cartilage defects, an injectable, immunomodulatory, and chondrogenic L-MNS-CMDA hydrogel is prepared through grafting vinyl and catechol groups to chitosan macromolecules using amide reaction, then further loading MnO2 nanosheets (MNS). The double crosslinking of photopolymerization and catechol oxidative polymerization endows L-MNS-CMDA hydrogel with preferable mechanical property, affording a suitable mechanical support for cartilage defect repair. Additionally, the robust tissue adhesion capability stemming from catechol groups guarantees the long-term retention of the hydrogel in the defect site. Meanwhile, L-MNS-CMDA hydrogel decomposes exogenous and intracellular H2O2 into O2 and H2O, to effectively alleviate cellular oxidative stress caused by long-term hypoxia. Under the synergies of catechol groups and MNS, L-MNS-CMDA hydrogel not only inhibits macrophages polarizing into M1 phenotype, but encourages them turn into M2 phenotype, thereby, reconstructing an immunization friendly microenvironment to ultimately enhance cartilage regeneration. Predictably, the hydrogel markedly induces rat bone marrow mesenchymal stem cells differentiating into chondrocytes by expressing abundant glycosaminoglycan and type II collagen. A cartilage defect model of rat knee joint indicates that L-MNS-CMDA hydrogel visually regulate the early inflammatory response of post-implantation, and facilitate cartilage regeneration and recovery of joint function after 12 weeks of post-implantation. All in all, this multifunctional L-MNS-CMDA hydrogel exhibits superior immunomodulatory and chondrogenic properties, holding immense clinical potential in the treatment of cartilage defects.

Variable Admittance Control of High Compatibility Exoskeleton Based on Human–Robotic Interaction Force

The wearable exoskeleton system is a typical strongly coupled human–robotic system. Human–robotic is the environment for each other. The two support each other and compete with each other. Achieving high human–robotic compatibility is the most critical technology for wearable systems. Full structural compatibility can improve the intrinsic safety of the exoskeleton, and precise intention understanding and motion control can improve the comfort of the exoskeleton. This paper first designs a physiologically functional bionic lower limb exoskeleton based on the study of bone and joint functional anatomy and analyzes the drive mapping model of the dual closed-loop four-link knee joint. Secondly, an exoskeleton dual closed-loop controller composed of a position inner loop and a force outer loop is designed. The inner loop of the controller adopts the PID control algorithm, and the outer loop adopts the adaptive admittance control algorithm based on human–robot interaction force (HRI). The controller can adaptively adjust the admittance parameters according to the HRI to respond to dynamic changes in the mechanical and physical parameters of the human–robot system, thereby improving control compliance and the wearing comfort of the exoskeleton system. Finally, we built a joint simulation experiment platform based on SolidWorks/Simulink to conduct virtual prototype simulation experiments and recruited volunteers to wear rehabilitation exoskeletons to conduct related control experiments. Experimental results show that the designed physiologically functional bionic exoskeleton and adaptive admittance controller can significantly improve the accuracy of human–robotic joint motion tracking, effectively reducing human–machine interaction forces and improving the comfort and safety of the wearer. This paper proposes a dual-closed loop four-link knee joint exoskeleton and a variable admittance control method based on HRI, which provides a new method for the design and control of exoskeletons with high compatibility.

Biomechanical characteristics of ligament injuries in the knee joint during impact in the upright position: a finite element analysis

BackgroundOur study aims to examine stress–strain data of the four major knee ligaments—the anterior cruciate ligament (ACL), the posterior cruciate ligament (PCL), the medial collateral ligament (MCL), and the lateral collateral ligament (LCL)—under transient impacts in various knee joint regions and directions within the static standing position of the human body. Subsequently, we will analyze the varying biomechanical properties of knee ligaments under distinct loading conditions.MethodsA 3D simulation model of the human knee joint including bone, meniscus, articular cartilage, ligaments, and other tissues, was reconstructed from MRI images. A vertical load of 300 N was applied to the femur model’s top surface to mimic the static standing position, and a 134 N load was applied to the impacted area of the knee joint. Nine scenarios were created to examine the effects of anterior, posterior, and lateral external forces on the upper, middle, and lower regions of the knee joint.ResultsThe PCL exhibited the highest stress levels among the four ligaments when anterior loads were applied to the upper, middle, and lower parts of the knee, with maximum stresses at the PCL-fibula junction measuring 59.895 MPa, 27.481 MPa, and 28.607 MPa, respectively. Highest stresses on the PCL were observed under posterior loads on the upper, middle, and lower knee areas, with peak stresses of 57.421 MPa, 38.147 MPa, and 26.904 MPa, focusing notably on the PCL-tibia junction. When a lateral load was placed on the upper knee joint, the ACL showed the highest stress 32.102 MPa. Likewise, in a lateral impact on the middle knee joint, the ACL also had the highest stress of 29.544 MPa, with peak force at the ACL-tibia junction each time. In a lateral impact on the lower knee area, the LCL had the highest stress of 22.279 MPa, with the highest force at the LCL-fibula junction. Furthermore, the maximum stress data table indicates that stresses in the ligaments are typically higher when the upper portion of the knee is affected compared to when the middle and lower parts are impacted.ConclusionsThis study recommends people avoid impacting the upper knee and use the middle and lower parts of the knee effectively against external forces to minimize ligament damage and safeguard the knee.

Unveiling the mechanical role of radial fibers in meniscal tissue: Toward structural biomimetics

The meniscus tissue is crucial for knee joint biomechanics and is frequently susceptible to injuries resulting in early-onset osteoarthritis. Consequently, the need for meniscal substitutes spurs ongoing development. The meniscus is a composite tissue reinforced with circumferential and radial collagenous fibers; the mechanical role of the latter has yet to be fully unveiled.Here, we investigated the role of radial fibers using a synergistic methodology combining meniscal tissue structure imaging, a computational knee joint model, and the fabrication of simple biomimetic composite laminates. These laminates mimic the basic structural units of the meniscus, utilizing longitudinal and transverse fibers equivalent to the circumferential and radial fibers in meniscal tissue.In the computational model, the absence of radial fibers resulted in stress concentration within the meniscus matrix and up to 800 % greater area at the same stress level. Furthermore, the contact pressure on the tibial cartilage increased drastically, affecting up to 322 % larger areas. Conversely, in models with radial fibers, we observed up to 25 % lower peak contact pressures and width changes of less than 0.1 %. Correspondingly, biomimetic composite laminates containing transverse fibers exhibited minor transverse deformations and smaller Poisson's ratios. They demonstrated structural shielding ability, maintaining their mechanical performance with the reduced amount of fibers in the loading direction, similar to the ability of the torn meniscus to carry and transfer loads to some extent. These results indicate that radial fibers are essential to distribute contact pressure and tensile stresses and prevent excessive deformations, suggesting the importance of incorporating them in novel designs of meniscal substitutes. Statement of significanceThe organization of the collagen fibers in the meniscus tissue is crucial to its biomechanical function. Radially oriented fibers are an important structural element of the meniscus and greatly affect its mechanical behavior. However, despite their importance to the meniscus mechanical function, radially oriented fibers receive minor attention in meniscal substitute designs. Here, we used a synergistic methodology that combines imaging of the meniscal tissue structure, a structural computational model of the knee joint, and the fabrication of simplistic biomimetic composite laminates that mimic the basic structural units of the meniscus. Our findings highlight the importance of the radially oriented fibers, their mechanical role in the meniscus tissue, and their importance as a crucial element in engineering novel meniscal substitutes.

Automated line scan profilometer based on the surface recognition method

Existing high-precision measurement devices face numerous challenges when dealing with complex surfaces, including high manual involvement, low measurement efficiency, and high costs. It is even more difficult to obtain complete surface data, particularly when confronted with unknown surfaces. This paper combines a fringe projection sensor with a high-precision line-structured light sensor to construct a line scan profiler. It proposes a surface recognition measurement method to overcome these challenges. This method fully leverages the fringe projection sensor's wide-field advantage to identify the object's surface shape and pose quickly. Subsequently, through the point cloud extraction and path planning algorithms proposed in this paper, efficient and complete line scan measurement paths are automatically generated, thus achieving the automation of the measurement process. Experimental measurements of aspherical lenses, freeform reflective mirrors, and artificial knee joint models validate the advantages of this method over existing methods in terms of measurement efficiency, automation capability, and applicability.

Surrogate-based worst-case analysis of a knee joint model using Genetic Algorithm

Verification, validation, and uncertainty quantification is generally recognized as a standard for assessing the credibility of mechanical models. This is especially evident in biomechanics, with intricate models, such as knee joint models, and highly subjective acquisition of parameters. Propagation of uncertainty is numerically expensive but required to evaluate the model reliability. An alternative to this is to analyze the worst-case models obtained within the specific bounds set on the parameters. The main idea of the paper is to search for two models with the greatest different response in terms of displacement-load curve. Real-Coded Genetic Algorithm is employed to effectively explore the high-dimensional space of uncertain parameters of a 2D dynamic knee model, while Radial Basis Function surrogates reduce the computation by orders of magnitude to near real-time, with negligible impact on the quality. It is expected that the studied knee joint model is very sensitive to uncertainty in the geometrical parameters. The obtained worst-case knee models showcase unrealistic behavior with one of them unable to fully extend, and the other largely overextending. Their relative difference in extension is up to 35% under ±1 mm bound set on the geometry. This unrealistic behavior of knee joint model is confirmed by the large standard deviation obtained from a classical sampling-based sensitivity analysis. The results confirm the viability of the method in assessing the reliability of biomechanical models. The proposed approach is general and could be applied to other mechanical systems as well.

Ergonomic assessment and gait analysis of a knee joint model with an active spring-reinforced centrally-rollable knee bypass support system &amp;nbsp;

Ergonomic assessment and gait analysis of a knee joint model with an active spring-reinforced centrally-rollable knee bypass support system &amp;nbsp;

Finite element analysis of the impact of bone mass and volume of low-density area under tibial plateau on lower limb alignment

To investigate the impact of the bone mass and volume of the low-density area under the tibial plateau on the lower limb force line by finite element analysis, offering mechanical evidence for preventing internal displacement of the lower limb force line in conjunction with knee varus in patients with knee osteoarthritis (KOA) and reducing bone mass under the tibial plateau. A healthy adult was selected as the study subject, and X-ray film and CT imaging data were acquired. Mimics 21.0 software was utilized to reconstruct the complete knee joint model and three models representing low-density areas under the tibial plateau with equal volume but varying shapes. These models were then imported into Solidworks 2023 software for assembly and verification. Five KOA finite element models with 22%, 33%, 44%, 55%, and 66% bone mass reduction in the low-density area under tibial plateau and 5 KOA finite element models with 81%, 90%, 100%, 110%, and 121% times of the low-density area model with 66% bone mass loss were constructed, respectively. Under physiological loading conditions of the human lower limb, the distal ends of the tibia and fibula were fully immobilized. An axial compressive load of 1 860 N, following the lower limb force line, was applied to the primary load-bearing area on the femoral head surface. The maximum stress within the tibial plateau, as well as the maximum displacements of the tibial cortical bone and tibial subchondral bone, were calculated and analyzed using the finite element analysis software Abaqus 2022. Subsequently, predictions regarding the alteration of the lower limb force line were made based on the analysis results. The constructed KOA model accorded with the normal anatomical structure of lower limbs. Under the same boundary conditions and the same load, the maximum stress of the medial tibial plateau, the maximum displacement of the tibial cortical bone and the maximum displacement of the cancellous bone increased along with the gradual decrease of bone mass in the low-density area under the tibial plateau and the gradual increase in the volume of the low-density area under tibial plateau, with significant differences ( P<0.05). The existence of a low-density area under tibial plateau suggests a heightened likelihood of knee varus and inward movement of the lower limb force line. Both the volume and reduction in bone mass of the low-density area serve as critical initiating factors. This information can provide valuable guidance to clinicians in proactively preventing knee varus and averting its occurrence.

Assessing the behavior of a hybrid model of the knee with contact surrogate under parameter uncertainties

Modeling the knee is an important factor in increasing the quality of life of both healthy individuals and patients. Nevertheless, the intricate nature of the knee makes this problem complicated. In this study, an extension to an established planar knee joint model with Hertzian contact pairs is proposed with contact mechanics based on polynomial chaos expansion surrogate. Firstly, the finite element (FE) model is made representing a contact pair of sphere-to-plane type with two layers on both bodies, corresponding to the cartilage and the bone. Five variables corresponding to both geometry and material parameters are used to parametrize this model. Then, 128 distinct variants of the FE model are created based on a quasi-Monte Carlo sequence. This dataset is used to train and validate the surrogate. The trained surrogate is proven to have predictive capabilities with an average nRMSE of 0.2% in randomized test/train splits. When included in a model of the knee and tested under parameter uncertainties in Monte Carlo simulations, it results in nRMSE of 58% for angular coordinate compared to the original model with Hertzian pair. This signifies the high influence of contact formulation on the model output and the need for more physically based models in knee contact modeling.

Comparison of the biomechanical properties of grafts in three anterior cruciate ligament reconstruction techniques based on three-dimensional finite element analysis

ObjectiveTo evaluate the biomechanical characteristics of grafts from three different anterior cruciate ligament (ACL) reconstructive surgeries and to determine which method is better at restoring knee joint stability.MethodsA 31-year-old female volunteer was enrolled in the study. According to the magnetic resonance imaging of her left knee, a three-dimensional model consisting of the distal femur, proximal tibia and fibula, ACL, posterior cruciate ligament, medial collateral ligament and lateral collateral ligament was established. Then, the ACL was removed from the original model to simulate the knee joint after ACL rupture. Based on the knee joint model without the ACL, single-bundle ACL reconstruction, double-bundle ACL reconstruction, and flat-tunnel ACL reconstruction were performed. The cross-sectional diameters of the grafts were equally set as 6 mm in the three groups. The bone tissues had a Young’s modulus of 17 GPa and a Poisson’s ratio of 0.36. The ligaments and grafts had a Young’s modulus of 390 MPa and a Poisson’s ratio of 0.4. Six probes were placed in an ACL or a graft to obtain the values of the equivalent stress, maximum principal stress, and maximum shear stress. After pulling the proximal tibia with a forward force of 134 N, the distance that the tibia moved and the stress distribution in the ACL or the graft, reflected by 30 mechanical values, were measured.ResultsThe anterior tibial translation values were similar among the three groups, with the double-bundle ACL reconstruction group performing the best, followed closely by the patellar tendon ACL reconstruction group. In terms of stress distribution, 13 out of 30 mechanical values indicated that the grafts reconstructed by flat bone tunnels had better performance than the grafts in the other groups, while 12 out of 30 showed comparable outcomes, and 5 out of 30 had worse outcomes.ConclusionCompared with traditional single-bundle and double-bundle ACL reconstructions, flat-tunnel ACL reconstruction has advantages in terms of stress dispersion. Additionally, flat-tunnel ACL reconstruction falls between traditional double-bundle and single-bundle ACL reconstructions in terms of restoring knee joint stability and is superior to single-bundle ACL reconstruction.

Smith machine squats pose high risk to ACL graft integrity after the ACL reconstruction and conventional squats are a safer alternative.

The purpose of this study was to evaluate the impact of squats after the anterior cruciate ligament (ACL) reconstruction on the ACL graft, considering new data on biomechanics, posterior tibial slope (PTS)and anterolateral ligament (ALL). Utilising finite element analysis on the new 14-component knee joint model, we have evaluated stresses on the knee elements separately for the knee with a native double-bundle ACL and with a single-bundle ACL graft for the 5° and 14° PTS variants during both conventional and Smith machine horizontal squats. Replacing a native ACL with a single-bundle graft causes an overstrain on the graft compared to the intact ACL under all conditions. Stresses on the ACL, ACL graftand ALL are much higher during the Smith machine squats compared to the conventional ones. The stress on the menisci is 3.6-4.9 times higher with conventional squats. PTS at the squats' lowest point minimally affects ACL stress but impacts menisci. The single-bundle ACL reconstruction (ACLR) does not reproduce the biomechanics of the native ACL and increases stresses in most knee joint elements, according to the current study. Conventional squats are relatively safe for the ACL graft at their lowest point. Passing the half-squat position is the most dangerous point. Smith machine horizontal squats produce stress on the ACL graft several times higher than its estimated breaking load and dangerous stress levels on the ALL. During the rehabilitation following ACLR, it is advisable to prioritise the conventional squats over Smith machine squats until ligamentisation is complete. Level III.

The Effect of Lower Limb Alignment on Tibiofemoral Joint Contact Biomechanics after Medial Meniscus Posterior Root Repair: A Finite-Element Analysis.

The purpose of this study was to determine how variations in lower limb alignment affect tibiofemoral joint contact biomechanics in the setting of medial meniscus posterior root tear (MMPRT) and associated root repair. A finite-element model of an intact knee joint was developed. Limb alignments ranging from 4° valgus to 8° varus were simulated under a 1,000 N compression load applied to the femoral head. For the intact, MMPRT, and root repair conditions, the peak contact pressure (PCP), total contact area, mean and maximum local contact pressure (LCP) elevation, and total area of LCP elevation of the medial tibiofemoral compartment were quantified. The PCP and total contact area of the medial compartment in the intact knee increased from 2.43 MPa and 361 mm 2 at 4° valgus to 9.09 MPa and 508 mm 2 at 8° of varus. Compared with the intact state, in the MMPRT condition, medial compartment PCP was greater and the total contact area smaller for all alignment conditions. Root repair roughly restored PCPs in the medial compartment; however, this ability was compromised in knees with increasing varus alignment. Specifically, elevations in PCP relative to the intact state increased with increasing varus, as did the total contact area with LCP elevation. After root repair, medial compartment PCP remained elevated above the intact state at all degrees tested, ranging from 0.05 MPa at 4° valgus to 0.27 MPa at 8° of varus, with overall PCP values increasing from 2.48 to 9.09 MPa. For varus alignment greater than 4°, root repair failed to reduce the total contact area with LCP elevation relative to the MMPRT state. Greater PCPs and areas of LCP elevation in varus knees may reduce the clinical effectiveness of root repair in delaying or preventing the development of tibiofemoral osteoarthritis.

HWJMSC-EVs promote cartilage regeneration and repair via the ITGB1/TGF-β/Smad2/3 axis mediated by microfractures

The current first-line treatment for repairing cartilage defects in clinical practice is the creation of microfractures (MF) to stimulate the release of mesenchymal stem cells (MSCs); however, this method has many limitations. Recent studies have found that MSC-derived extracellular vesicles (MSC-EVs) play an important role in tissue regeneration. This study aimed to verify whether MSC-EVs promote cartilage damage repair mediated by MFs and to explore the repair mechanisms. In vitro experiments showed that human umbilical cord Wharton’s jelly MSC-EVs (hWJMSC-EVs) promoted the vitality of chondrocytes and the proliferation and differentiation ability of bone marrow-derived MSCs. This was mainly because hWJMSC-EVs carry integrin beta-1 (ITGB1), and cartilage and bone marrow-derived MSCs overexpress ITGB1 after absorbing EVs, thereby activating the transforming growth factor-β/Smad2/3 axis. In a rabbit knee joint model of osteochondral defect repair, the injection of different concentrations of hWJMSC-EVs into the joint cavity showed that a concentration of 50 µg/ml significantly improved the formation of transparent cartilage after MF surgery. Extraction of regenerated cartilage revealed that the changes in ITGB1, transforming growth factor-β, and Smad2/3 were directly proportional to the repair of regenerated cartilage. In summary, this study showed that hWJMSC-EVs promoted cartilage repair after MF surgery.Graphical abstract

Finite element analysis of sagittal angles of unicompartmental knee arthroplasty

BackgroundUnicompartmental knee arthroplasty is an effective treatment for knee osteoarthritis, but it has the risk of failure, and the installation position of the prosthesis is one of the factors affecting the failure. There are few biomechanical studies on the installation angle of unicompartmental knee prosthesis. MethodsConstructed a finite element model of a normal human knee joint, and the validity of the model was verified by stress and front anterior methods. The mobile-bearing unicompartmental knee arthroplasty femoral prosthesis was placed at 3° intervals from 0° sagittal plane to 15° flexion, and − 2° and 17°were established, and observing the biomechanical changes of components. FindingsMaximum peak stresses occurred at a sagittal mounting angle of −2° for the insert and the contralateral meniscus, with the tibia showing a maximum at 17° sagittal and the tibial prosthesis stress maximum occurring at 6° sagittal. As the sagittal plane angle of the femoral prosthesis increases and the osteotomy distance extends posteriorly, more bone is amputated during the osteotomy. The ratio of the distance from the tip of the anterior intramedullary nail to the anterior end of the osteotomy to the total anteroposterior length of the sagittal osteotomy ranged from 43.2% to 44.6%. InterpretationIn this paper, the more appropriate sagittal mounting position for the femoral prosthesis is between 9 and 12°, based on the amount of osteotomy and the peak stress of each component in a standing position.

Can lateral tenodesis improve the rotational stability of the ACL reconstruction? A finite element analysis.

One of the most common knee injuries is the Anterior Cruciate Ligament (ACL) rupture with severe implications on knee stability. The usual treatment is the ACL Reconstruction (ACLR) surgery where the surgeon replaces the torn ligament with a graft in an effort to restore knee kinematics. In case of excessive rotatory instability, Lateral Extra-Articular Tenodesis (LET) can be performed in combination with ACLR. Additionally, LET appears to reduce ACLR graft forces minimizing graft failure chances. However, there are concerns about overconstraining physiological rotation. To gain insight in this controversial topic, we developed an automatic, open-source tool to create a series of Finite Element (FE) models attempting to investigate the interactions of ACLR and LET through simulation. We started by creating a validated model of the healthy knee joint that served as reference for subsequent FE simulations. Then, we created FE models of standalone ACLR and combined ACLR-LET. Each model was assessed by applying a loading profile that resembles the reduction phase of the Pivot-Shift clinical exam. We measured the External Tibia Rotation (ETR), the Posterior Tibia Translation (PTT) of the lateral tibial compartment, and the ACLR graft stress developed around the femoral tunnel insertion site. We observed the following: a) LET reduces ETR and PTT compared to isolated ACLR, b) combined ACLR-LET is more sensitive to LET graft pretension with lower values showcasing performance closer to the healthy joint, c) LET reduces ACLR graft forces for the same pretension values, d) LET exhibits significant overconstraint for higher pretension values. In general, these findings are in agreement with relevant clinical studies and accentuate the potential of the developed framework as a tool that can assist orthopaedists during surgery planning. We provide open access for the FE models of this study to enhance research transparency, reproducibility and extensibility.

Effect of residual volume after surgery of the discoid lateral meniscus on tibiofemoral joint biomechanics: a finite element analysis

BackgroundThe purpose of this study was to investigate the influence of different residual meniscus volume on the biomechanics of tibiofemoral joint after discoid lateral meniscus (DLM) surgery by finite element analysis.MethodsA knee joint model was established based on CT and MRI imaging data. The DLM model was divided into five regions according to conventional meniscectomy, with volumes of 15%, 15%, 15%, 15%, 15%, and 40% for each region. Additionally, the DLM model was divided into anterior and posterior parts to obtain ten regions. The DLM was resected according to the design scheme, and together with the intact discoid meniscus, a total of 15 models were obtained. Finite element analysis was conducted to assess shear and pressure trends on the knee joint.ResultsThe study observed significant changes in peak shear stress and compressive stress in the lateral meniscus and lateral femur cartilage. As the meniscus volume decreased, there was an increase in these stresses. Specifically, when the meniscus volume reduced to 40%, there was a sharp increase in shear stress (302%) and compressive stress (152%) on the meniscus, as well as shear stress (195%) and compressive stress (157%) on the lateral femur cartilage. Furthermore, the model grouping results showed that preserving a higher frontal volume in the meniscus model provided better biomechanical advantages.ConclusionThe use of finite element analysis has demonstrated that preserving more than 55% of the meniscus volume is necessary to prevent a significant increase in joint stress, which can potentially lead to joint degeneration. Additionally, it is crucial to preserve the front volume of the DLM in order to achieve improved knee biomechanical outcomes.