Microstructural Refinement Research Articles

Study on Mechanism of Microstructure Refinement by Ultrasonic Cavitation Effect

During the solidification process of the alloy, the temperature lies in the range between the solid-phase line and the liquidus. Dendrite growth exhibits high sensitivity to even slight fluctuations in temperature, thereby significantly influencing the tip growth rate. The increase in temperature can result in a reduction in the rate of tip growth, whereas a decrease in temperature can lead to an augmentation of the tip growth rate. In cases where there is a significant rise in temperature, dendrites may undergo fracture and subsequent remelting. Within the phenomenon of ultrasonic cavitation, the release of internal energy caused by the rupture of cavitation bubbles induces a substantial elevation in temperature, thereby causing both dendrite remelting and fracture phenomena. This serves as the main mechanism behind microstructure refinement induced by ultrasonic cavitation. Although dendrite remelting and fracture exert significant influences on the solidification process of alloys, most studies primarily focus on microscopic characterization experiments, which fail to unveil the transient evolution law governing dendrite remelting and fracture processes. Numerical simulation offers an effective approach to address this gap. The existing numerical models primarily focus on predicting the dendrite growth process, while research on remelting and fracture phenomena remains relatively limited. Therefore, a dendrite remelting model was established by incorporating the phase field method (PFM) and finite element difference method (FDM) into the temperature-induced modeling, enabling a comprehensive investigation of the entire process evolution encompassing dendrite growth and subsequent remelting.

An Analysis of Dynamic Recrystallization During the Reduction Pretreatment Process Using a Multiscale Model

In this study, a multiscale model is developed through secondary development (UMAT and UEXTERNALDB) in Abaqus with the objective of simulating the thermal deformation process with dynamic recrystallization behavior. The model couples the finite element method (FEM) with the multiphase field model (MPFM), thereby establishing bidirectional coupling between macroscopic mechanical behavior and microstructural evolution. A comparison between the single-element hot compression simulation and experimental results demonstrates that the model accurately simulates both the macroscopic mechanical behavior and microstructural evolution during the thermal deformation process, thereby exhibiting high precision. Simulations of the reduction pretreatment (RP) process under different reduction amounts and billet surface temperatures demonstrate that increasing the reduction amount and billet surface temperature significantly enhances both plastic deformation and the volume fraction of dynamic recrystallization in the billet core. This results in the closure of core voids and the refinement of the core microstructure, thereby providing valuable guidance for the development of optimal reduction pretreatment (RP) processes.

Process optimization and finite element modeling in magnetorheological abrasive finishing of SS-316L with surface characterization

This study explores the potential of Magnetorheological Abrasive Finishing (MRAF) for ultra-precision finishing of SS-316L using a high-performance Nd-Fe-B (N-35 grade) magnetic tool. Key parameters, including the relationship between normal force (Fn) and working gap, magnetic flux distribution, and finishing spot area, were analyzed using ANSYS 2020 R1® Magnetostatic module simulations. Material removal rate (MRR) and surface roughness (Ra) were optimized through response surface methodology (RSM) using a central composite design (CCD) with two primary input factors: SiC abrasive volume fraction (5%, 10%, 15%) and abrasive mesh size (800, 1000, 1200). Statistical analysis via ANOVA revealed a significant influence of process variables, achieving a remarkable surface finish with a minimum Ra of 52 nm in just 60 min, utilizing an MR fluid with 10% SiC abrasives. Microscopic and spectroscopic evaluations confirmed enhanced surface morphology and microstructural refinement. Moreover, bioactivity studies in simulated body fluid highlighted improved hydroxyapatite layer formation on the finished SS-316L samples, underscoring the process’s potential for biomedical applications.

A Critical review on the performance and microstructural characteristics of materials fabricated through friction stir additive methods and deposition techniques

This review examines the distinctions between metallic alloys fabricated using friction stir techniques in additive manufacturing, focusing on friction stir additive manufacturing (FSAM) and additive friction stir deposition (AFSD) of aluminium, magnesium, and titanium alloys. The analysis emphasizes the microstructural characteristics and mechanical properties of these alloys. FSAM is noted for its ability to produce refined equiaxed grains, contributing to enhanced mechanical strength and structural integrity. In contrast, AFSD is characterized by its ability to achieve significant microstructural refinement, leading to improved hardness and corrosion resistance. However, challenges such as resolution limitations, mechanical stability issues in high-aspect-ratio structures, and the need for optimized post-processing persist. The study underscores the potential of FSAM and AFSD to advance additive manufacturing by addressing these challenges and optimizing process parameters for a wide range of engineering applications.

Microstructure Refinement of Bulk Inconel 718 Parts During Fabrication with EB-PBF Using Scanning Strategies: Transition from Bidirectional-Raster to Stochastic Point-Based Melting

Inconel 718 is a widely popular aerospace superalloy known for its high-temperature performance and resistance to oxidation, creep, and corrosion. Traditional manufacturing methods, like casting and powder metallurgy, face challenges with intricate shapes that can result in porosity and uniformity issues. On the other hand, Additive Manufacturing (AM) techniques such as Powder Bed Fusion (PBF) and Direct Energy Deposition (DED) can allow the creation of intricate single-part components to reduce weight and maintain structural integrity. However, AM parts often exhibit directional solidification, leading to anisotropic properties and potential crack propagation sites. To address this, post-processing treatments like HIP and heat treatment are necessary. This study explores the effects of the raster and stochastic spot melt scanning strategies on the microstructural and mechanical properties of IN718 parts fabricated using Electron Beam Powder Bed Fusion (EB-PBF). This research demonstrates that raster scanning produces columnar grains with higher mean aspect ratios. Stochastic spot melt scanning facilitates the formation of equiaxed grains, which enhances microstructural refinement and lowers anisotropy. The highest microstructural values were recorded in the raster-produced columnar grain structure. Conversely, the stochastic melt-produced transition from columnar to equiaxed grain structure demonstrated increased hardness with decreasing grain size; however, the hardness of the smallest equiaxed grain structure was slightly less than that of the columnar grain structure. These findings underscore the vital importance of scanning strategies in optimizing the EB-PBF process to enhance material properties.

Effect of Mo on the Phase Transformation, Microstructure, and Hardness of Q500qENH Weathering Steel of Bridge Construction during Continuous Cooling

This article investigates the precipitation behavior of Mo element in the continuous cooling phase transformation process of weathering steel of bridge construction and its influence on microstructure and hardness. The results demonstrate that the addition of Mo leads to the narrowing of the phase transformation interval of proeutectoid ferrite and pearlite, the expansion of the bainite transformation zone, a delayed bainite phase transformation process, and the refinement of bainite microstructure. Moreover, theoretical calculations of bainite phase transformation kinetics reveal that the average activation energy for bainite transformation in Mo‐free and Mo‐containing steels is 94.8 and 134.0 kJ mol−1, respectively. The new grains of Mo‐free steel mainly grow in a 2D mode, while Mo containing steel mainly grows in a 1D mode, which confirms the retarding effect of Mo on bainite grain growth. Additionally, Mo significantly increases the number density and refines the size of precipitated phases in weathering steel of bridge construction. Within the cooling rate range of 0.1–30 °C s−1, the hardness of weathering steel of bridge construction is enhanced by Mo, with the magnitude of hardness increment decreasing as the cooling rate increases. This behavior is primarily governed by the combined influence of phase transformation strengthening and precipitation strengthening.

Understanding the grain refinement and residual stress formation mechanisms of a Ni-based alloy during machining processes

Ni-based alloys are important materials for many industries, microstructure of the sub-surface regions of these alloys can be refined during machining processes, affecting both their machinability and service performance. Several mechanisms have been proposed to explain the machining-induced microstructure refinement of these alloys, however, sound evidences to support them are still lacking. In this research, microstructure characterization with an emphasis on the micro-texture and defects was conducted on milled surfaces of a Ni-based alloy, to promote in-depth understanding of the grain-refinement process. A nano-crystalline layer consisted a topmost region with randomly-orientated grains and annealing nano-twins and a textured region beneath it with deformed microstructure was observed in the cross-section of the alloy with the help of high resolution orientation determination techniques. These observations provide additional evidences to support the recrystallization induced grain-refinement mechanism of the nano-grains. It is also suggested that recrystallization was a by-product of the shear deformation occurred during the milling process, supported by the observation of the clear boundary between the nano-grain layer and its beneath deformed region. The deformed region was refined as a result of mechanical twining and twin-intersections, leading to significant fluctuations of the residuals stresses.

Effect of rare earth yttrium and the deformation process on the thermal deformation behavior and microstructure of pure titanium for cathode rolls

This study explores the challenges associated with microstructural refinement and homogenization control for large titanium cathode rolls utilized in electrolytic copper foil production. An innovative deformation control strategy was developed by incorporating yttrium microalloying within the β→α dual-phase region to refine the hot-deformed microstructure of pure titanium. Gleeble thermal simulation tests were performed to assess the impact of rare earth Y, deformation temperatures (700–900 °C), and interpass cooling rates (5 °C/s, 25 °C/s, and 50 °C/s) on the hot deformation behavior and microstructural evolution of pure titanium. The results reveal that Y2O3 particles generated by the addition of rare earth Y enhance dynamic recrystallization through the particle-stimulated nucleation (PSN) mechanism, effectively pinning grain boundaries and impeding recrystallized grain growth. Increased interpass cooling rates lead to finer grains and higher stored energy. The mechanism for grain refinement during dual-phase deformation is described as follows: β-phase nonrecrystallization temperature deformation → rapid cooling control → α-phase recrystallization deformation control, energy storage, strain-induced dynamic phase transformation (SIDT, α→β), and dynamic recrystallization (DRX). Under experimental conditions of β-phase region deformation at 980 °C → inter-pass cooling rate of 50 °C/s → α-phase region deformation at 750 °C, the addition of rare earth yttrium achieved the most effective grain refinement, reducing the average grain size to 2.56 μm.

Interfacial microstructure and fracture mechanism of Cu/Al composite plate jointing process assisted by pulsed current-melted Al spheres: Finite element analysis and experimental studies

In this work, a novel method based on pulsed-current-assisted vacuum sintering processes was employed to fabricate the Cu/Al laminated metal composites (LMCs) with outstanding mechanical properties. The microstructural evolution, interfacial characteristics, phase composition, mechanical properties, and fracture behavior of Cu/Al composites prepared by the melted Al spheres induced with high-frequency pulsed current were investigated. Results show that robust interfacial bonding without micropores and cracks, and the grain structure consists mainly of recrystallized and substructured grains characterized by high angular grain boundaries. Meanwhile, interfacial analysis identifies melted Al and Al2Cu phases within the transition layer, exhibiting distinctive features such as "Al+Al2Cu" corrugated interfaces and island eutectic structures. Additionally, mechanical properties demonstrate superior strength (210 ± 13 MPa) and elongation (27 % ± 0.7 %) in specimens with corrugated interfaces compared to those with flat interfaces. Finite element analysis further elucidates stress redistribution and fracture behavior, emphasizing the enhanced coordinated deformation in specimens featuring corrugated interfaces. These findings underscore the significance of interface engineering and microstructural refinement in optimizing the mechanical performance of Cu/Al composite materials, offering valuable insights for their application in diverse engineering domains.

Effects of ZrO2 Nano-Particles' Incorporation into SnAgCu Solder Alloys: An Experimental and Theoretical Study.

This study investigates the mechanism and effects of incorporating different ZrO2 nano-particles into SAC0307 solder alloys. ZrO2 nano-powder and nano-fibers in 0.25-0.5 wt% were added to the SAC0307 alloy to prepare composite solder joints by surface mount technology. The solder joints were shear tested before and after a 4000 h long 85 °C/85% RH corrosive reliability test. The incorporation of ZrO2 nano-particles enhanced the initial shear force of the solder joint, but they decreased the corrosion resistance in the case of 0.5 wt%. SEM, EDS, and FIB analysis revealed intensive growth of SnO2 on the solder joint surfaces, leading to the formation of Sn whiskers. Density functional theory (DFT) simulations showed that, despite Sn being able to bond to the surface of ZrO2, the binding energy was weak, and the whole system was therefore unstable. It was also found that ZrO2 nano-particles refined the microstructure of the solder joints. Decreased β-Sn grain size and more dispersed intermetallic compounds were observed. The microstructural refinement caused mechanical improvement of the ZrO2 composite solder joints by dispersion strengthening but could also decrease their corrosion resistance. While ZrO2 nano-particles improved the solder joint mechanical properties, their use is recommended only in non-corrosive environments, such as microelectronics for space applications.

Refinement of microstructure and improvement of mechanical properties of directed energy deposited titanium alloys by adding Fe

Elemental alloying is a validated strategy for enhancing the mechanical properties of directed energy deposited titanium alloys. However, it is still a challenge to obtain titanium alloys with both high strength and high ductility. In this work, to balance strength and ductility, the alloying element Fe was in-situ added to the TC4 melt pool during the directed energy deposited process and the effects of its content on the microstructure and mechanical performance of the TC4 alloy deposits were investigated. The results showed that the Fe additive ranging from 0.5 to 2.0 wt% were completely solid-solved in the retained β phase of TC4 alloys. Moreover, the primary β columnar grains were transformed into fully equiaxed grains. Meanwhile, the presence of Fe refined the α-laths, increased the proportion of the retained β phase, and the continuous grain boundary α (GB-α) became discontinuous. The tensile strength of the deposited alloys was continually improved with increasing Fe content, while the elongation had a peak value. When the Fe content was 1.0 wt%, the deposited alloy exhibited the best comprehensive performance, with an ultimate tensile strength of 1071 MPa and an elongation of 9.3 %. The enhancement of tensile strength was attributed to the solid solution strengthening and the refinement of α-laths and primary β grains. The increased proportion of retained β phase and the formation of discontinuous GB-α were beneficial for the alloy ductility. However, increased α/β interfaces inhibited dislocation movements, resulting in a decrease in ductility. The development of this alloy is important for aerospace and other fields that require high strength, high ductility and lightweight.

Microstructure Refinement in Solidification of a Deeply Undercooled Ternary Nickel Based Alloy

Microstructure Refinement in Solidification of a Deeply Undercooled Ternary Nickel Based Alloy

Effects of temperature and stress evolution on microstructural change and mechanical properties during friction element welding

Dissimilar material joining is essential for improving the strength-to-weight ratio of materials for various applications. Friction element welding (FEW) is a promising solution for joining highly dissimilar materials that vary in strength and thickness. However, the influence of the process parameters on the material’s resultant microstructure and mechanical properties remains unclear. In this study, the relationship between microstructure and microhardness distribution of the welded specimen is experimentally studied, and the effects of temperature and stress evolution are revealed by a thermal–mechanical finite element model. It is found that the microhardness can be improved by over 50% in the central region due to microstructural change and grain refinement. The beneficial microstructural change can be achieved by inducing either a high peak temperature (over the austenitization temperature) or a high peak stress (over the hardening factor) during the FEW process, which can be obtained by controlling the endload and rotational speed of the friction element. The size of the region with improved hardness is observed to vary with the depth of deformation in the steel layer. For the transverse shear strength (TSS), it is observed that irrespective of the temperature levels reached, TSS increases with increasing stress in the steel layer. Temperature plays a crucial role when the steel layer’s temperature is higher than the austenitization start temperature wherein TSS increases with the temperature.

Effects of residual elements on the microstructure and mechanical properties of a Q&P steel

Producing steel requires large amounts of energy to convert iron ores into steel, which often comes from fossil fuels, leading to carbon emissions and other pollutants. Increasing scrap usage emerges as one of the most effective strategies for addressing these issues. However, typical residual elements (Cu, As, Sn, Sb, Bi, etc.) inherited from scrap could significantly influence the mechanical properties of steel. In this work, we investigate the effects of residual elements on the microstructure evolution and mechanical properties of a quenching and partitioning (Q&P) steel by comparing a commercial QP1180 steel (referred to as QP) to the one containing typical residual elements (Cu+As+Sn+Sb+Bi<0.3wt%) (referred to as QP-R). The results demonstrate that in comparison with the QP steel, the residual elements significantly refine the prior austenite grain (9.7μm vs. 14.6μm) due to their strong solute drag effect, leading to a higher volume fraction (13.0% vs. 11.8%), a smaller size (473 nm vs. 790 nm) and a higher average carbon content (1.26 wt% vs. 0.99 wt%) of retained austenite in the QP-R steel. As a result, the QP-R steel exhibits a sustained transformation-induced plasticity (TRIP) effect, leading to an enhanced strain hardening effect and a simultaneous improvement of strength and ductility. Grain boundary segregation of residual elements was not observed at prior austenite grain boundaries in the QP-R steel, primarily due to continuous interface migration during austenitization. This study demonstrates that the residual elements with concentrations comparable to that in scrap result in significant microstructural refinement, causing retained austenite with relatively higher stability and thus offering promising mechanical properties and potential applications.

Microstructural refinement of an Al-Ce-Mg alloy via Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the low solubility of Ce in the Al matrix. The Al11Ce3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al11Ce3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al11Ce3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ∼60 % compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20 %, with a simultaneous 15 % improvement in ductility compared to the binary Al-Mg alloy. These results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

Microstructure and high temperature tribological behavior of nickel-based superalloy with addition of revert

The recycling of revert plays a crucial role in cost-efficiency and green manufacturing of superalloy. In this study, optical microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, tensile test, and tribological analysis were employed to investigate the microstructure, mechanical properties, and tribological behaviors of vacuum induction melted superalloys of 100% original material (Sample 1) and 40% original material + 60% revert (Sample 2). Dry sliding tests were conducted at 300 and 730 °C. The addition of revert promotes microstructure refinement, hardness increase, and carbide formation, at the cost of 18.5% ductility loss. During the high-temperature dry sliding process, abrasive, adhesive, and oxidative wear mechanisms were observed on the contact surfaces. Sample 2 exhibited a lower wear rate and coefficient of friction at both 300 and 730 °C. Additionally, a more continuous and wear-resistant tribolayer was formed on the wear track of Sample 2, effectively mitigating matrix oxidation compared to Sample 1. At 730 °C, a thick tribolayer developed on the wear surface of Sample 2, characterized by a hard and wear-resistant glaze layer on the outermost surface. The continuous sliding induced matrix heating, which facilitates recrystallization in the subsurface of Sample 2, induced by increased inclusions and carbides from the revert. The analysis of wear debris further illustrated the variations of wear mechanism at different temperatures. These findings are meaningful for understanding the high-temperature behavior of superalloys and optimizing alloy recycling process.

Microstructure Refinement via Nucleation of Intragranular Acicular Ferrite Stimulated by Ti-Containing Core-Shell Structured Particles in Low-Carbon Steel.

This study investigated the microstructure, mechanical properties, and nucleation mechanism of acicular ferrite (AF) present in hot-rolled Ti deoxidized steel. In our experiments, the impact toughness of Ti deoxidized steel is significantly increased to 144 J at -20 °C, while those Mn and Al deoxidized steels are only 9 J and 18 J, respectively. Interlocked AF is the primary microstructure of Ti deoxidized steel. The second-phase particles of the core-shell-type structure, in which Ti2O3 is the nucleus and TiO is the outermost shell, act as effective nucleating agents to stimulate AF nucleation. The low lattice disregistry between TiO and AF is the main factor contributing to the production of AF. It is also revealed that Ti2O3 and MnS fulfill the particular orientation relationship, contributing to the formation of an Mn-depleted zone (MDZ) adjacent to MnS, proposed to be one of the possible mechanisms for promoting AF nucleation.

The influences of microstructural length scale on the tensile properties and deformation mechanisms of Sn-3.0Ag-0.5Cu solder alloys

Optimizing microstructures remains critical for improving the reliability of Pb-free solder joints, especially in applications with high failure risks. The mechanical properties of Sn-3.0Ag-0.5Cu (SAC305) solder alloys is intricately linked to the length scale of the initial microstructure. This paper investigates the effects of microstructure refinement on uniaxial tensile properties, nanomechanical response, plastic deformation, and fracture using directional solidification techniques. The findings demonstrate that controlling the microstructure can effectively enhance mechanical properties, dynamic recrystallization, and intragranular deformation in SAC305 alloys. Furthermore, the study explores heterogeneous plastic deformation and the interaction between eutectic intermetallics and β-Sn. These results offer valuable insights for optimizing microstructures to achieve superior solder joint performance.

The Microstructure, Mechanical Properties, and Precipitation Behavior of 1000 MPa Grade GEN3 Steel after Various Quenching Processes

This study examines the microstructure, mechanical properties, and precipitation behavior of 1000 MPa grade GEN3 steel when subjected to various quenching processes, with a focus on the quench and partition (Q&amp;P) technique. The Q&amp;P-treated samples achieved 1300 MPa tensile strength and demonstrated superior yield strength, attributed to their refined substructure and their large amounts of precipitates. The quenched samples exhibited the thinnest martensite laths due to the highest martensite volume. Despite the as-annealed samples having the smallest grain size, the Q&amp;P treatment resulted in optimal microstructural refinement results and a high dislocation density, reaching 1.15 × 1015 m−2. Analysis of the precipitates revealed the presence of V8C7, M7C3, M2C, and Ti(C, N) across various heat treatments. The application of the McCall–Boyd method and the Ashby–Orowan correction model indicated that quench and tempered (Q&amp;T) samples contained the largest volume of fine precipitates, contributing to their high yield strengths. These findings offer valuable insights for optimizing heat treatment processes to develop advanced high-strength steels for industrial applications.

Microstructure refinement, mechanical performances and degradability of biomedical Zn-2Cu alloy by ultrasonic melting and homogenization treatment

Zn alloys are deemed to be desired body implant materials because of their moderate degradation rate. In this paper, the microstructural evolution, mechanical performances, and degradability of Zn-2Cu alloy prepared by ultrasonic melt treatment (UMT) with different ultrasonic powers (0 W, 300 W, 600 W, and 900 W) were systematically studied. Under the condition of UMT, the coarse α-Zn grains of Zn-2Cu alloy were refined into fine equiaxed grains and the mean size was significantly decreased from 133.4 μm to 65.3 μm when the ultrasound power was enhanced. The precipitating CuZn5 phase was significantly refined from the coarse block into the spherical shape. Moreover, the fraction of the CuZn5 precipitates of the Zn-2Cu alloy was greatly reduced with the increase of ultrasonic power. Tensile tests showed that the ultimate tensile strength (UTS), yield strength (YS), and elongation (El) of Zn-2Cu alloy were remarkably enhanced to 203 MPa, 167 MPa, and 8.14 %, respectively, when the Zn-2Cu alloy melting was treated by 600 W power. It was found by electrochemical polarization test that the degradation rate of Zn-2Cu alloy treated by UMT with 0 W, 300 W, 600 W, and 900 W power in Hank’s solution was gradually decreased to 1.6312 mm/a, 1.3206 mm/a, 1.0992 mm/a, and 1.2832 mm/a, respectively. In addition, after the Zn-2Cu alloys were immersed in Hank’s solution for 30 days, the degradation rate of samples was summarized as 0 W alloy (0.472 mm/a) > 300 W alloy (0.436 mm/a) > 900 W alloy (0.412 mm/a) > 600 W alloy (0.398 mm/a). The studies verified that the UMT was a very valuable technology for preparing Zn-2Cu alloy, which can meet the requirement of mechanical properties and degradable rate as a promising implant material.