Microstructural Analysis Research Articles

Design of high performance Cu-Ni-Si alloys via a multiobjective strategy based on machine learning

Herein, the ultimate tensile strength and electrical conductivity of precipitation-strengthened Cu-Ni-Si alloys were simultaneously improved by utilizing a machine learning-based multiobjective design strategy. The multiobjective design strategy consists of five main steps: creating the initial dataset, generating alloy features, screening key alloy features, modeling and inversely designing, and experimental iteration. Of particular note is the constraint placed on the initial composition-properties dataset, considering the rules governing the addition of Co. This constraint ensures that the dataset adheres to the required specifications. To evaluate the optimized degree of the inverse design composition, a joint expectation improvement function was employed. This function effectively integrates the ultimate tensile strength and electrical conductivity. Through a process of five mutually reinforcing iterations of machine learning and experimentation, the combined property of the designed alloy surpasses the Pareto frontier initially formed by the collected data. Microstructure analysis further confirmed the significant precipitation strengthening effects achieved in the optimized alloy.

Prevention of weld decay in TIG welded AISI 304 steel pipes

Weld decay due to chromium carbide precipitation at grain boundaries in the heat affected zone (HAZ) during TIG welding of austenitic stainless steels. This issue is particularly significant concerning the welding of AISI 304 steels, commonly used in the food industry. Although this problem can be overcome with different methods, there are some restrictions. A novel technique for welding AISI 304 steel pipes is introduced to reduce weld decay and improve the mechanical properties. The use of this technique, which includes faster cooling after welding, significantly minimizes the time of precipitation of chromium carbide. Temperature measurements and microstructural analyses monitor precipitation and the impact of the technique on the mechanical characteristics of AISI 304 steel pipes was assessed through hardness and hoop tensile tests. There was a 6% increase in hardness values observed in the HAZ region. Furthermore, a 16.7% increase in maximum load and a 127.4% increase in elongation. The reduction in chromium carbide precipitation observed in the microstructural analysis was confirmed through the double loop electropotentiokinetic reactivation (DLEPR) test, specifically for assessing intergranular corrosion. With the novel method, there was a 25% increase in corrosion resistance in the HAZ and a 40% increase in the weld zone.

Investigating the Electrocatalytic Oxygen Evolution Reaction of Hydrothermally Synthesized NiFe2O4 Nanoparticles

In this study, nickel ferrite (NiFe2O4) nanoparticles were synthesized using the hydrothermal method at various pH values. The objective was to investigate the influence of pH variation on particle size and electrocatalytic activity. The formation of cubic phase nanoparticles was confirmed through X-ray diffraction (XRD) analysis. To characterize the electrochemical properties, the nickel ferrite nanoparticles were coated onto a stainless steel substrate using the doctor blade technique. The microstructural analysis was conducted using scanning electron microscopy (SEM). The samples were further analyzed using linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). The average crystallite size, determined from the XRD pattern, was approximately 40 nm. SEM images revealed a conversion from nanoplates to a granular morphology. The synthesized electrode exhibited an overpotential of 392 mV at 10 mA/cm2 and demonstrated good stability for 5 hours. These findings highlight the excellent electrocatalytic activity of nickel ferrite nanoparticles for the oxygen evolution reaction (OER).

Accelerated pork salting using needle electrode-derived pulsed electric fields

This study aimed to evaluate the effects of pulsed electric field (PEF) pretreatment on the NaCl content, protein composition, and microstructure of pork during the marination process. The results showed that needle PEF could promote salt penetration into the center of pork pieces. Under optimal PEF conditions (3.0 kV/cm, 200 Hz, and 2400 pulses), the marination time could be reduced by almost 12 h. Protein characterization also revealed that PEF pretreatment changes myofibrillar protein properties by promoting salt penetration toward the center of pork. Furthermore, microstructural analysis demonstrated that the enhanced marination effect could be attributed to the PEF treatment-induced expansion of gaps between muscle bundles. Industrial relevanceIn this study, a PEF-assisted curing technique significantly (P < 0.05) improved salt penetration into the center of pork. Reducing the differences between internal and external salt concentrations can produce a more homogeneous marinade and reduce the marination time. Our findings suggest that PEF pretreatment is a promising and effective pretreatment technique for curing meat products.

Annealing response and yielding behavior of cold rolled advanced HSLA steels

High-strength low-alloy (HSLA) steel is well established in car body manufacturing. They comprise a lean low-carbon alloy concept and can be produced by a wide variety of processing routes. However, cold-rolled HSLA steels are typically limited to a yield strength of 460 MPa by current standards. This research work will present a concept of extending the yield strength range of cold-rolled HSLA steels to above 500 MPa. A key aspect is to find the right balance between recovery and recrystallization of the cold rolled matrix during the annealing stage thereby mitigating the influence of solute and precipitated niobium. Additional solute draging power was introduced by alloying molybdenum to one of the investigated steels. A detailed microstructural analysis using transmission electron microscopy revealed that under recovery annealing conditions an ultrafine-grained microstructure with ferrite grain sizes between 0.5 and 1 μm can be established leading to large strength contribution via the Hall-Petch relationship. Strength losses related to partial recrystallization can be recovered to an extent of around 200 MPa by the precipitation of nano-sized niobium carbide particles. It is demonstrated that the presence of niobium and molybdenum in solute condition have the most prominent influence on obstructing recrystallization via solute drag. It is furthermore shown that the magnitude of precipitation strengthening correlates with the Lüders strain. The analysis of the work hardening behavior indicated that the n-value in ultrafine-grained condition approaches a lower limit value of 0.03 and raises to above 0.2 with progressing recrystallization as well as precipitation strengthening. The detailed evaluation of the tensile characteristics indicates that the strength limit for these HSLA steels ranging between 830 and 880 MPa is reached when the average grain size is reduced to 0.46 μm. The results of this study used to define robust processing conditions to securely produce steel grades in the 600-800 MPa yield strength range.

Unveiling the self-annealing phenomena and its effect on microstructure and texture evolution in the room temperature rolled Cu-0.13Sn-0.04Mg alloy

ABSTRACT In this study, we investigated the microstructural evolution of a Cu-0.13Sn-0.04Mg alloy that underwent heat treatment followed by room temperature rolling (RTR). Initially heat-treated specimens were rolled at room temperature (RT) with reduction ratios (RR) of 40% and 75% to perform microstructural and crystallographic textural analyses. Electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) were utilise to examine both initial and deformed microstructures. Both exhibited heterogeneous microstructural distributions. Shear bands (SBs) existed in the initial specimen and became main sites for the nucleation of new grains during heat treatment. A denser presence of SBs was noted in the RTR specimens. Remarkably, an unusual self-annealing phenomenon was observed in these specimens, culminating in the emergence of recrystallized grains at RT. A plethora of such grains was observed in the severely deformed specimens, with numerous nucleating grains appearing proximal to the SBs or deformed grain boundaries (GBs). Time dependent microstructure evolution was observed via ex-situ EBSD technique in the compressed specimens. Formation of new grains, increase in high angle grain boundaries (HAGBs), and dislocation annihilations were observed with the progress of time. The crystallographic texture evolution in the initial specimen was predominantly influenced by the S component. At lower strains, the fractions of Copper component increased, whereas at higher strains, a greater fraction of Brass and S components were induced. Following a 40% RR, a saturation in hardness value was observed, which could be potentially attributable to an accelerated rate of RT recrystallization in the case of 75% RR.

Development of a High Ductility DP Steel Using a Segregation Neutralization Approach: Benchmarked Against a Commercial Dual Phase Steel

AbstractCommercial dual-phase steels are typically synonymous with a banded distribution of martensite in their microstructures, which can degrade ductility and increase the anisotropy of mechanical properties. The concept of neutralizing the effect of Mn segregation is employed to change the distribution of martensite to a non-banded distribution. To this end, the ratio of austenite and ferrite stabilizer elements has been changed in the composition of dual-phase steel. Microstructural analysis has been carried out on both hot-rolled (ferrite + pearlite) and heat-treated (ferrite + martensite) microstructures by optical microscope and EBSD, respectively. The microstructural examinations have confirmed the non-banded distribution of second phase and more equiaxed ferrite grains in the segregated neutralized grade microstructures compared to a commercially benchmarked dual-phase steel. Tensile properties of two grades have also been assessed in hot-rolled and heat-treated conditions in RD, TD, and 45 deg tensile directions. In the case of heat-treated condition, total elongation in RD direction has been improved from 20.9 pct in benchmark dual-phase steel to 25.4 pct in segregated neutralized dual-phase steel. Tensile anisotropy results showed a significant difference in tensile strength by tensile direction in benchmark dual-phase steel in both hot-rolled (~ 85 MPa) and heat-treated conditions (~ 48 MPa), while the corresponding differences for the segregated neutralized grades were 14 and 15 MPa, respectively.

Development of functionally gradient Cu-Fe based sintered brake pad materials

The world is seeking a sustainable co-existence with nature to preserve the balance of our ecosystem. This has opened a wider market for green and renewable forms of energy to realize the energy requirements of global countries. Among the various renewable energy sources, harnessing the kinetic energy of the wind through a turbine to generate electricity has seen an ardent growth. Wind turbines, in general, function between 2 m s−1 and 25 m s−1 wind speed. When the winds cross the cut-out speed (25 m s−1) or during the maintenance of wind turbine components, the brakes are implemented. The primary aerodynamic and secondary mechanical brakes comprise the wind turbine braking system. The mechanical brake pads are fixed to the brake caliper. On braking, the brake caliper pushes the brake pads against the brake disc. This recurring action gradually wears the brake material. The presence of ceramic particles in the traditionally used bulk composite pads imparts poor joint properties between the brake pad and caliper. These mandate frequent replacement of the brake pads. The current research work developed a functionally gradient brake pad through the powder metallurgy technique. The microstructure, microhardness, and tribological properties of the fabricated brake pads are tested and analyzed. Microstructural analysis revealed a homogeneous distribution of the reinforcements in the metal matrix. COF was observed to be within the desired range of between 0.3 and 0.4. The brake pad exhibited a combination of adhesive-abrasive-oxidative wear.

Fine-Pitch Copper Nanowire Interconnects for 2.5/3D System Integration

AbstractHeterogeneous integration is a key driver within the field of advanced electronic packaging. The realization of tomorrow’s highly integrated electronic systems depends on the combination and compatibility of various integration technologies at the same hierarchy level. The adoption of novel bonding technologies for a cost-effective realization of multi-chiplet systems is a key aspect. Cu nanowire (NW) interconnects exhibit distinct advantages in terms of their scalability down to a few micrometers, the resulting joint properties and moderate demands with respect to the surface preparation, and the cleanliness of the bonding environment. No solder or flux is required for the bonding process, but the NW bumps still can compensate low height differences. The bonding process can be carried out near room temperature under ambient conditions. We demonstrate the technological possibility to integrate the Cu-NWs for a bump processing scheme including the Cu seed etching on 300 mm wafer for the first time. This paper focuses on the microstructure evaluation and the shear test of the formed Cu-NW interconnects fabricated under ambient conditions within a few seconds. The microstructure analysis shows the intact bonded interconnects and reveals high-resolution details of Cu-NWs. The shear strength of the formed interconnects varies between 4.6 MPa and 90.5 MPa depending on the bonding and annealing conditions. Overall, the results of this study highlight the potential of Cu-NW interconnects for future 3D heterogeneous system integration.

Cerebral microstructural alterations in Post-COVID-condition are related to cognitive impairment, olfactory dysfunction and fatigue

After contracting COVID-19, a substantial number of individuals develop a Post-COVID-Condition, marked by neurologic symptoms such as cognitive deficits, olfactory dysfunction, and fatigue. Despite this, biomarkers and pathophysiological understandings of this condition remain limited. Employing magnetic resonance imaging, we conduct a comparative analysis of cerebral microstructure among patients with Post-COVID-Condition, healthy controls, and individuals that contracted COVID-19 without long-term symptoms. We reveal widespread alterations in cerebral microstructure, attributed to a shift in volume from neuronal compartments to free fluid, associated with the severity of the initial infection. Correlating these alterations with cognition, olfaction, and fatigue unveils distinct affected networks, which are in close anatomical-functional relationship with the respective symptoms.

Effect of Recycled Concrete Aggregate Addition on the Asphalt Mixtures Performance: ITZ Area, Microstructure, and Chemical Analysis Perspectives

The importance of environmental consciousness and sustainability is increasing among transportation governing bodies worldwide. Many government bodies are concerned with maximizing the usage of recycled substances in road construction. Therefore, assessing the effect of recycled materials consumption is essential, mainly when designing new ‘green’ pavement types. The primary objective of this study is to investigate the impact of different treatments on improving the interfacial transition zone (ITZ) of coarse recycled concrete aggregate (CRCA) and its application in asphalt mixes. Such an aim is accomplished by enhancing its physical and mechanical characteristics, as well as its microstructure. The surface morphology, chemical composition, and intermix phases of the ITZ area and calcium silicate hydrate (CSH) compounds for CRCA were evaluated using scanning electron microscopy (SEM), an energy-dispersive X-ray analyzer (EDAX), and X-ray diffraction analysis (XRD). The performance of asphalt mixtures that included treated and untreated CRCA was also examined using different tests. It was found that heat treatment is an effective technique for enhancing the ITZ. However, cracks were seen in the mortar of CRCA when exposed to high temperatures (500 °C), which adversely affects the characteristics of the mortar. Acid treatment appeared to be an effective approach for improving the ITZ area. Nevertheless, the treatment that used acetic acid, a weak acid, was more effective than HCl acid, a strong acid. The outcomes revealed that the ITZ microstructure is significantly enhanced under different treatment types; however, microstructure improvements mainly included increased surface homogeneity and CSH compounds and a reduced Ca/Si ratio. It was also found that the asphalt mixtures with different proportions of untreated CRCA exhibited enhanced resistance to rutting. Furthermore, their tensile strength ratio (TSR) values were above the minimal level requirements. Moreover, the asphalt mixture with 30% CRCA, which was treated with various treatment methods, demonstrated a significant improvement in the mixtures’ mechanical properties; therefore, its application is highly successful and an environmentally friendly solution.

Divacancy and resonance level enables high thermoelectric performance in n-type SnSe polycrystals

N-type polycrystalline SnSe is considered as a highly promising candidates for thermoelectric applications due to facile processing, machinability, and scalability. However, existing efforts do not enable a peak ZT value exceeding 2.0 in n-type polycrystalline SnSe. Here, we realized a significant ZT enhancement by leveraging the synergistic effects of divacancy defect and introducing resonance level into the conduction band. The resonance level and increased density of states resulting from tungsten boost the Seebeck coefficient. The combination of the enhanced electrical conductivity (achieved by increasing carrier concentration through WCl6 doping and Se vacancies) and large Seebeck coefficient lead to a high power factor. Microstructural analyses reveal that the co-existence of divacancy defects (Se vacancies and Sn vacancies) and endotaxial W- and Cl-rich nanoprecipitates scatter phonons effectively, resulting in ultralow lattice conductivity. Ultimately, a record-high peak ZT of 2.2 at 773 K is achieved in n-type SnSe0.92 + 0.03WCl6.

Numerical simulation of concrete strength based on microstructure and mineral composition analysis using micro-CT and XRD technology

The investigation of mechanical properties in porous materials, such as concrete, has been a significant area of interest in the fields of civil engineering and architecture. Traditional macroscopic mechanical testing methods are limited due to destructive experimental conditions, time-consuming procedures, and the inability to characterize internal structures. To overcome these limitations, researchers have utilized microscopic factors with micro-CT and simulation models. Different simulation methods demand mechanical parameters to effectively model the constituent materials; however, there exists variability in the amount and standard values of these input parameters, which leads to a decrease in the reliability of the obtained results. In order to tackle this issue, a novel approach is proposed, which integrates mineral component analysis using X-ray diffraction (XRD) and establishes coefficients to minimize the number of necessary input parameters. Simulation results demonstrate excellent agreement with experimental measurements, accurately reproducing the stages of elastic deformation, failure, and fracture in the stress-strain curve of concrete. Our findings reveal that changes in the concrete skeletal structure, microstructure, and mineral composition significantly influence compressive strength. Coarse aggregates and high-mechanical-performance minerals, in particular, have a substantial impact. Additionally, the mechanical properties show a significant linear relationship with the strength reduction coefficient of aggregates and concrete cores. In conclusion, the proposed method, combining CT scanning and XRD with FDEM, proves to be a reliable and practical approach for accurately assessing the mechanical properties of concrete. This methodology simplifies the intricate processes associated with the time-intensive parameter calibration, leading to a more efficient parameter allocation procedure. As a result, this method enhances concrete design, promotes a better understanding of parameter impacts, and enables accurate prediction of concrete behavior across diverse scenarios.

Preparation of geopolymer for in-situ pavement construction on the moon utilizing minimal additives and human urine in lunar regolith simulant

Constructing lunar pavements is of great significance for improving the transportation efficiency of materials and personnel transfer at lunar bases. Utilizing lunar regolith for the in-situ preparation of geopolymer is an effective means of supplying raw materials for lunar pavement construction. This present study prepared geopolymers for pavement material with lunar regolith simulant. The influence of NaOH on the compressive strength of geopolymers was understood by using different percentages of NaOH as alkaline activator. The effect of urine on the compressive strength of geopolymers by using artificial urine of different pH values as liquid phases. The results indicated that the addition of artificial urine slightly reduces the compressive strength of geopolymers, and the effects of pH and NaOH percentage are different. Microstructural analysis performed by Mercury Intrusion Porosimetry and Scanning Electron Microscope, indicated that choosing fine-particle lunar regolith simulant as precursor is more conducive to the preparation of high-strength geopolymers using human urine.

Enhancing microstructure and mechanical properties of dissimilar TIG welded duplex 2205 and Ni-based inconel 718 superalloy through post weld heat treatment

In demanding applications, maintaining structural integrity in dissimilar welded joints like those between duplex stainless steel and Ni-based superalloys requires achieving the best possible mechanical properties. This work examines the impact of post-weld heat treatment (PWHT) on the mechanical characteristics of joints made via double-sided tungsten inert gas (TIG) welding. The dissimilar welded joint was investigated by exposing it to the PWHT for 12 h at 650 °C. Reducing the negative impact of heat generated by welding on the mechanical characteristics and microstructure of the fusion zone was the main goal. To study for changes in the microstructure before and after PWHT, optical microscopy and scanning electron microscopy methods were used for microstructural analysis. To determine the effect of PWHT on the welded joints, mechanical properties such as tensile strength, toughness, and ductility were also assessed. The mechanical properties showed significantly enhanced characteristics and refined grain structures in the fusion zone.

Prediction on Partial Replacement of Cement and Coarse Aggregate by Zeolite Powder and Steel Slag in High-Performance Concrete

Abstract High performance concrete is obtained by the inclusion of mineral admixtures like silica fume and fly ash in the concrete.. The research explores the viability and performance of sustainable concrete by introducing zeolite powder as a partial substitute for cement and steel slag as a partial replacement for coarse aggregate in M-70 grade concrete. Zeolite powder, possessing pozzolanic properties, is a natural or synthetic aluminosilicate material, while steel slag is an industrial byproduct with potential as an alternative aggregate source. The main objective is to investigate the impact of zeolite powder and steel slag on the development of High-Performance Concrete (M-70) in accordance with BIS standards.The formulation of high-performance concrete involved replacing 12.5%, 15%, and 17.5% of the cement with zeolite powder and varying the proportion of steel slag as a replacement for coarse aggregate (ranging from 30% to 55%). A comprehensive mechanical test was conducted on these specimens and compared with conventional concrete. Among the 21 mixes, the optimal combination was identified, incorporating 15% zeolite powder as a cement replacement and 45% steel slag as a coarse aggregate replacement, resulting in superior performance compared to conventional concrete.Subsequently, the experimental results were compared with predicted outcomes using the Taguchi method. The close alignment between the values obtained experimentally and those predicted further validates the effectiveness of the optimized mix ZP15SS45. This mix was further studied for water absorption, non-destructive testing, and microstructural analysis. The results from these investigations indicate that the optimum mix outperforms conventional concrete in terms of water absorption, non-destructive testing, and microstructural characteristics.&amp;#xD;

Sustainable engineering of human hair fiber-composite in engineering application

The hybrid composite material, resulting from the fusion of human hair and Kevlar 29 synthetic fiber in a 10:1 ratio, reinforced with epoxy resin using the hand layup technique, underwent meticulous mechanical and thermal testing. The investigation encompassed tensile, flexural, and impact property evaluations, elucidating a notable enhancement in mechanical strength with a diminishing synthetic fiber content. Concomitantly, the composite exhibited commendable heat resistance in heat deflection tests, making it potentially suitable for applications in elevated temperature environments. Water absorption properties were scrutinized, revealing a correlation between reduced synthetic fiber content and diminished water absorption, implying heightened durability in diverse conditions. Microstructure analysis through SEM provided intricate insights into the internal composition. In summation, the composite, featuring a higher proportion of natural fibers and a lower proportion of synthetics, demonstrated superior mechanical attributes, optimal heat resistance, and reduced water absorption, showcasing its applicability in automotive and engineering domains, particularly in the fabrication of vehicle panels and components. The aim of this research represents a significant advancement in composite materials, offering a cost-effective solution that balances mechanical strength and thermal resistance. It suggests the potential for high-performance materials by combining natural and synthetic fibers, promising versatility across various applications.

Simultaneous integration of anti Si-poisoning and anti-fading properties on an innovative Al grain refiner via Nb-modified TiB2

Si-poisoning and fading effect of grain refiners deteriorate the refining effect of Al-Si alloys (Si≥3 wt%), further worsening the performance of alloys. In this work, an innovative Al-Nb-Ti-B with anti Si-poisoning and anti-fading properties was prepared by introducing synthetic TiB2 into Al-Nb melt. At the cooling rate of 1.4 K/s, the average grain size of Al-7Si alloys inoculated by this Al-Nb-Ti-B was refined to 326.05 μm, 40% reduction compared to 549.06 μm by commercial Al-5Ti-1B. The grain size remained at 421.95 μm even after 120 min holding time. Anti-fading mechanism was investigated by size distribution analysis of TiB2 nucleating particles. Anti Si-poisoning mechanism is attributed to Nb element which accumulates on the (01—10) surface of TiB2 and reduces the lattice misfit between TiB2 and α-Al. Atomic-scale microstructure analysis and first-principles calculations reveal that the Nb enrichment on TiB2 increases the chemical affinity of TiB2/Al interface and decreases the Si adsorption propensity. In brief, appropriate size distribution and unique Nb-rich layer contribute to the excellent grain refinement of TiB2 particles modified by Nb. These findings may shed new light on the realm of innovative aluminum grain refiners.

In-vitro bioactivity investigation and surface properties of a PMMA-SiO2 composite coating on SS-316L using the Sol-Gel technique

Surface modification of SS-316L using an organic and inorganic hybrid coating of polymethyl methacrylate (PMMA) and silicon dioxide (SiO2) is being conducted in the current investigation with crosslinking agent 3-aminopropyl tri-ethoxy silane (APTES). The solvent-gel method and dip coating with varying amount of SiO2 (i.e. 0.5, 1, and 1.5 wt.%) is used for surface modification. On the coated surface, Fourier transform infrared spectroscopy (FTIR) at 1000–1250 cm−1 reveals the crosslinking of silicon and PMMA. The coatings formed on SS-316L are homogenous, transparent, and free of defects and voids when seen macroscopically. A good crystallinity and presence of coated material can be seen from the X-ray diffraction and microstructure analysis of coated surface. The PMMA coating with 1.5 wt.% SiO2 has the most apatite crystals deposited on surface as observed with 7 days of immersion on simulated body fluid (SBF). These findings provide a solid link that coating SS-316L with SiO2 promotes bone bioactivity, and the PMMA+1.5 wt.% SiO2 coating can be employed on implants. The results of this study suggest a sustainable coating solution for improved bioactivity in medical applications and surgical instruments.

Influence of Cement and Water Content on the Multifaceted Capabilities of a Self-Sensing Cement-based Geocomposite: A Comprehensive Analysis

Abstract This study investigates the synergistic effects of cement, water, and hybrid carbon nanotubes/graphene nanoplatelets (CNT/GNP) concentrations on the mechanical, microstructural, durability, and piezoresistive properties of self-sensing cementitious geocomposites. Varied concentrations of cement (8% to 18%), water (8% to 16%), and CNT/GNP (0.1% to 0.34%, 1:1) were incorporated into cementitious stabilized sand (CSS). Mechanical characterization involved compression and flexural tests, while microstructural analysis utilized dry density, apparent porosity, water absorption, and non-destructive ultrasonic testing, alongside TGA, SEM, EDX, and XRD analyses. The durability of the composite was also assessed against 180 Freeze-thaw cycles. Moreover, the piezoresistive behaviour of the nano-reinforced CSS was analyzed during cyclic flexural and compressive loading using the four-probe method. The optimal carbon nanomaterials (CNM) content was found to depend on the water and cement ratios. Generally, elevating the water content led to a rise in the CNM optimal concentration, primarily attributed to improved dispersion and adequate water for the cement hydration process. The maximum increments in flexural and compressive strengths, compared to plain CSS, were significant, reaching up to approximately 30% for flexural strength and 41% for compressive strength, for the specimen containing 18% cement, 12% water, and 0.17% CNM. This improvement was attributed to the nanoparticles' pore-filling function, acceleration of hydration, regulation of free water, and facilitation of crack-bridging mechanisms in the geocomposite. Further decreases in cement and water content adversely impacted the piezoresistive performance of the composite. Notably, specimens containing 8% cement (across all water content variations) and 10% cement (with 8% and 12% water content) showed a lack of piezoresistive responses. In contrast, specimens containing 14% and 18% cement displayed substantial sensitivity, evidenced by elevated gauge factors, under loading conditions.