Microplastics Research Articles

The Detection and Analysis of Microplastics in a Typical Mountainous Drinking Water System in China

Microplastics (MPs) are widely detected in urban drinking water systems. However, the presence and characteristics of MPs in mountainous drinking water systems with independent and simple filtration facilities have been overlooked. In this study, we revealed the ubiquity of MPs and demonstrated that their concentrations increased along with the pipeline length in Bainitan Village, Tiantai County, China. The simple filtration facility in this village did not effectively remove most MPs. Polyethylene, polyurethane, and polyethylene terephthalate were the dominant polymers in water samples (72.32% in total), while polyvinylchloride, polyurethane, and polyethylene were the most prevalent in the sediment (74.00% in total) of the reservoir. Long fragments were the predominant shape of MPs in all samples, with the majority being smaller than 100 μm. The estimated daily intake of MPs through drinking water ingestion was highest in infants (2.14–31.26 MPs/kg bw/day), compared to children (1.41–20.67 MPs/kg bw/day) and adults (1.05–15.35 MPs/kg bw/day), highlighting their increased vulnerability. This emphasizes the need for advanced water treatment systems in mountainous regions. It also underscores the necessity for government attention to improve water safety in remote areas. Our research will contribute valuable baseline data for further research on MP exposure, particularly in mountainous communities.

Unraveling Plastic Pollution in Protected Terrestrial Raptors Using Regurgitated Pellets

The threat of plastic pollution has escalated to unprecedented levels, with particular concern surrounding microplastics (MPs) and artificial fibers or particles (AFs) due to their wide distribution across ecosystems and their bioavailability to wildlife. Although research on the impact of plastic on wild birds is rapidly growing, knowledge of terrestrial species remains limited, especially regarding raptors, which have been significantly understudied. Here, we investigated the prevalence of MPs and AFs in regurgitated pellets from six protected terrestrial raptor species, namely the Cinereous Vulture (Aegypius monachus), the Bonelli’s Eagle (Aquila fasciata), the Little Owl (Athene noctua), the Lesser Kestrel (Falco naumanni), the Red Kite (Milvus milvus), and the Barn Owl (Tyto alba), collected between 2022 and 2023. Our analysis revealed that 68% of the pellets contained MPs (47 out of 69), and 81% contained AFs (56 out of 69). Additionally, two macroplastics were found inside the pellets: a cable tie in a Red Kite and a bird identification ring in a Cinereous Vulture. The concentrations (mean ± standard error of the mean) were 2.39 ± 0.39 MPs/pellet and 5.16 ± 0.72 AFs/pellet. The concentration of MPs and AFs varied significantly among some of the studied species; however, no significant differences were observed among urban, rural, and protected areas. This could indicate that contamination levels are mainly related to the type of species. Fibers emerged as the predominant contaminant shape, with six different polymers identified, among which PET, PE, and acrylics were the most prevalent. These findings highlight that plastic pollution has reached protected terrestrial raptors and that the impact of plastic on their life cycles needs to be assessed.

Global microplastics pollution: a bibliometric analysis and review on research trends and hotspots in agroecosystems.

The prevalence of microplastics (MPs) in agricultural ecosystems poses a notable threat to dynamics of soil ecosystems, crop productivity, and global food security. MPs enter agricultural ecosystems from various sources and have considerable impacts on the physiochemical properties soil, soil organisms and microbial communities, and plants. However, the intensity of these impacts can vary with the size, shape, types, and the concentrations of MPs in the soil. Besides, MPs can enter food chain through consummation of crops grown on MPs polluted soils. In this study, we conducted a bibliometric analysis of 1636 publications on the effects of MPs on agricultural ecosystems from 2012 to May 2024. The results revealed a substantial increase in publications over the years, and China, the USA, Germany, and India have emerged as leading countries in this field of research. Social network analysis identified emerging trends and research hotspots. The latest burst keywords were contaminants, biochar, polyethylene microplastics, biodegradable microplastics, antibiotic resistance genes, and quantification. Furthermore, we have summarized the effects of MPs on various components of agricultural ecosystems. By integrating findings from diverse disciplinary perspectives, this study provides a valuable insight into the current knowledge landscape, identifies research gaps, and proposes future research directions to effectively tackle the intricate challenges associated with MPs pollution in agricultural environments.

Effect of background ions and physicochemical factors on the cotransport of microplastics with Cu2+ in saturated porous media

Microplastics (MPs) in subsurface environments are migratory and can carry heavy metals, increasing the extent of MP and heavy metal pollution. This study used quartz sand-filled column experiments to investigate the adsorption and cotransport behaviours of PS-MPs, O3, UV-aged PS-MPs, and Cu2+ at different MP concentrations, ionic strengths, and ionic valences in a saturated porous medium. The results showed that when MPs migrate alone in the absence of an ionic background, higher concentrations have increased mobility. In contrast, an increase in the background ion concentration or ion valence inhibits the individual transport capacity of PS-MPs. An increase in the concentration of background ions or elevation in the valence state promotes Cu2+ transport because of the action of the double electric layer on the surface of the colloid and the electrostatic repulsive forces combined with the background ions. The adsorption capacity of aged PS-MPs was stronger than that of PS-MPs because of the binding of the aged PS-MPs to Cu2+ through complexation and electrostatic attraction. In the binary system of PS-MPs/Cu2+, PS-MPs promoted Cu2+ transport and the mobility of Cu2+ loaded by PS-MPs decreased with increasing background ion concentration. The cotransport results showed that MPs promote Cu2+ transport in the following order: O3-aged Ps > UV-aged Ps > Ps, as the increasing cation concentration in the MPs and Cu2+ occupies the PS surface adsorption sites. Overall, PS is an effective carrier for Cu2+. These findings offer fresh exploration concepts for the joint migration of MPs and heavy metals in underground settings.

Microplastic and human health with focus on pediatric well-being: a comprehensive review and call for future studies.

Although humans are highly dependent on plastics from infancy to adolescence, these materials can degrade into ubiquitous microplastics (MPs) that affect individuals at every stage of life. However, information on the sources, mechanisms, detection techniques, and detrimental effects of MPs on children's health from infancy to adolescence is limited. Hence, here we identified and reviewed original research papers published in 2017-2023 across 11 database categories in PubMed, Google Scholar, Scopus, and Web of Science to improve our understanding of MPs with a focus on pediatric well-being. These studies found that milk and infant formulas are common sources of MP exposure in infants. Infant formula is the dominant source of MPs in babies, while plastic toys are a common source of MPs in toddlers. Adolescents are frequently exposed to MPs through the consumption of food contaminated with MPs and the use of plastics in food packaging. Water and air are sources of MP exposure in children from infancy through adolescence. This study thoroughly summarized how MP exposure in children of all ages causes cell damage and leads to adverse health effects such as cancer. With appropriate authorization from the relevant authorities, small amounts of human biological samples (10 g of feces) were collected from volunteers to assess the amounts of MPs in children with the aim of promoting pediatric well-being. The samples were then treated with Fenton's reagent, stored in glass jars, and filtered through nonplastic filters. Finally, MPs in children were quantified using stereomicroscopy and characterized using micro-Fourier transform infrared spectroscopy.

Microplastics removal from a hospital laundry wastewater combining ceramic membranes and a photocatalytic membrane reactor: Fouling mitigation, water reuse, and cost estimation

The release of microplastics (MPs) through industrial laundry wastewater accounts for 35 % of global MPs emissions into the environment and it is a significant environmental problem, especially because MPs can absorb contaminants of emerging concern (CECs) from garments. This study is the first to evaluate and perform a cost estimation of the MP removal from hospital laundry wastewater (HLWW) using a combination of ceramic membranes and a pilot-scale photocatalytic membrane reactor (PMR) as a fouling mitigation strategy. The HLWW, from a hospital in Copenhagen, Denmark, contained a total organic carbon (TOC) of 345 mg L⁻1 and 1.4 × 106 MP L−1, mainly of polyethylene terephthalate (PET) ranging between 100 and 200 μm in size. The pre-treatment with an ultrafiltration (UF) ZrO₂ membrane successfully removed 96 % of MPs and over 98 % of suspended solids and turbidity at an estimated cost of 0.45 US$ per m3 of permeate. In the PMR stage, ultraviolet light emitting diodes (UV LED) irradiation reduced irreversible fouling, improving permeate flow and minimizing the need for chemical cleaning. The Ce–Y–ZrO2/TiO2 photocatalytic membrane achieved over 99 % removal of turbidity, colour, and suspended solids, as well as 99.9 % removal of MPs, allowing the potential effluent reuse within the hospital laundry. Additionally, the retentate from the PMR process had lower TOC, easing the discharge of this concentrated stream. The cost estimation demonstrated that the photocatalytic degradation combined with traditional techniques, i.e. backflush and chemical cleaning, is more economical than using these techniques separately. Therefore, the total treatment cost was 1.09 US$ per m3 of permeate, which is lower than the cost of fresh water in Denmark. In conclusion, this innovative treatment strategy offers a sustainable and cost-effective solution for HLWW management, not only reducing water consumption by enabling water reuse in the hospital laundry but also advances towards achieving net-zero liquid discharge and contributing to the UN Sustainable Development Goals for clean water (Goal 6) and climate action (Goal 13).

Standardization of FTIR-Based Methodologies for Microplastics Detection in Drinking Water: A Meta-Analysis Indeed and Practical Approach

The detection of microplastics (MPs) in drinking water presents significant environmental and public health challenges. This study comprises two stages: a meta-analysis aimed at standardizing Fourier Transform Infrared Spectroscopy (FTIR) methods for MP detection, followed by the practical implementation of these findings in the laboratory. The review of studies conducted from 2019 to 2023 identifies 0.45 μm cellulose nitrate filters and Nile red staining as the most effective techniques for fluorescent detection. Experimental results demonstrate the superior retention capabilities of cellulose nitrate filters and the uniformity of Nile red staining. This dual approach not only optimizes water treatment processes but also enhances the accuracy of MP detection. The findings contribute to improved water quality management and public health protection by establishing robust protocols for MP analysis.

Fire parameters of recycled plastic pellets

AbstractDuring the recycling process, waste plastic undergoes various processes that change its geometry. The thermal properties and fire behaviour of plastic in different geometries has not been widely studied. This paper aims to determine critical thermal properties of plastic pellets made of recycled plastic. For this paper, cone calorimeter tests of various volumes of recycled plastic pellets of low‐ and high‐density polyethylene and polypropylene were conducted. During these tests, the heat release rate (HRR), mass loss rate and time‐to‐ignition were measured, thereafter the heat of combustion (HOC) was calculated. A calibration of suitable time‐to‐ignition equations is carried out. The average HRR is between 353 and 581 kW/m2 with an external heat flux of 50 kW/m2. The measured time‐to‐ignition values ranged between 27 s at 50 kW/m2 and just more than 90 s at 25 kW/m2. Values obtained analytically from the thermally thin time‐to‐ignition equations for these materials describe ignition well, which appears to be due to the particulate nature of the samples. The HOC (40–41 MJ/kg) shows good agreement with the HOC for virgin plastic found in literature. These properties can be used as a basis for material characterisation, and further testing will be done before using this as simulation inputs to determine how bulk stored plastic pellets will behave in the event of a fire.

Indoor Airborne Microplastics: Human Health Importance and Effects of Air Filtration and Turbulence

Microplastics (MPs) are omnipresent particles that receive special attention because of their persistent nature and their potential impact on human disease and on the environment. Most MPs are generated by the degradation of larger plastic items such as clothing, car tires, and discarded plastic materials. In indoor environments, where human beings spend most of their time, aerial MP levels are higher, and the majority are fibers produced from textiles. Airborne MPs indoors are a greater potential danger to humans than MPs ingested in food and drink. Fragments small enough to remain substantially suspended in the air column, the small airborne microparticles that are measured as PM10 and PM2.5, become available for assimilation by human beings through respiration, potentially producing various health problems. Larger MPs act by ingestion and skin contact. MPs can carry microorganisms and micropollutants adsorbed to their surfaces, facilitating their uptake and survival within the human body. Indoor airborne MPs thus represent emerging pollutants of fast-growing concern that are especially important as potential invaders of the human respiratory system, reaching the alveoli of the lungs and finally entering the circulatory system and other tissues. Since this direct human exposure to MP contamination via indoor air is so important, we discuss in this article the ways in which MP concentration and dispersal in indoor air can be affected by air turbulence that is induced by anthropogenic objects such as air conditioners, filters, and purifiers. Much evidence is equivocal and further research is necessary.

Levels and Classification of Microplastics and Their Impact on the Wellbeing of Selected Commercially Important Fish Species in Kisumu Bay, Lake Victoria.

Microplastics (MPs) are emerging pollutants of concern in aquatic ecosystems. Fish ingest MPs accidentally during normal feeding because they resemble prey or by ingesting prey that previously consumed them. Despite severe plastic pollution in Africa, some countries, including Kenya have implemented laws to curb this pollution menace. MPs have scantly been studied in African freshwaters. This study provides empirical data and describes the levels of MPs in four commercially important fish species in Lake Victoria. A total of 95 fish samples were collected from four sampling sites (inshore-offshore waters) between March and May 2022. Microscopy and Attenuated Total Reflectance Fourier Transformed Infrared (ATR-FTIR) spectroscopy methods were used to identify MPs. In this study, 62 out of 95 (65.26%) of the gastrointestinal tracts of the sampled fish contained MPs. The four species showed different proportions of detected MPs among the sampled individuals: 75.00% (Clarias gariepinus), 75.00% (Synodontis victoriae), 71.43% (Lates niloticus), and 59.26% (Oreochromis niloticus). Polystyrene (PS) and poly (perfluorobutadiene) were the main plastic polymers in the fish samples. The condition factors estimated for O. niloticus, S. victoriae, and L. niloticus were > 1 and < 1 for C. gariepinus, respectively. Positive correlations were observed between microplastic numbers and fish length and microplastic numbers and fish weight. However, the low R2 values obtained implied no strong relationship exists between these parameters. These findings provide evidence of microplastic contamination in fish in Kisumu Bay.

Capillary Skimming of Floating Microplastics via a Water-Bridged Ratchet.

Floating microplastics (MPs) have recently become a major concern in marine pollution; however, current filter-based technology is hardly effective for directly removing such MPs from the water surface because of specific mesh size and clogging issues. This paper introduces a new skimming concept for removing floating MPs utilizing capillary force mediated by the elevation of a hydrophilic ratchet at the air-water interface. MPs floating near the ratchet surface are spontaneously forced toward the ratchet with a concave water meniscus, driven by the Cheerios effect. The MPs can then be skimmed and temporarily held by the deforming concave water meniscus as the ratchet rises. Here, it is found that the stability of the water bridge plays a crucial role in skimming success because it provides capillary adhesion between the MP and the ratchet. The proposed capillary skimming method is observed to be effective across nearly all types of floating MPs, ranging in size from 1 to 4 mm, and with densities varying from 0.02 to 0.97 gcm- 3, which is also demonstrated by a prototype of marine robot cleaner.

Fibrous foes: First report on insidious microplastic contamination in dietary fiber supplements

Regular consumption of health supplements to balance dietary intake has gained popularity worldwide. One such supplement that has gained popularity among consumers is dietary fibers. Microplastic (MPs) contamination in various food products is being reported worldwide. However, there is a paucity of understanding of the occurrence of MPs in dietary supplements. This study addresses this gap by investigating the degree of MPs contamination in dietary fiber supplements. Nine commonly consumed (powder and gummy-based) over-the-counter dietary fiber supplements in Australia were tested in this study. Microscopic examination revealed the presence of MPs fibers and fragments in all the tested products. Further categorization showed that MPs particles were of various colours, including black, blue, red, green, and white. The order of polymer abundance was Polyamide > Polydiallyl Phthalate > polyethylene polypropylene diene > Polyurethane = Polyethylene terephthalate > Polyethylene = Ethylene acrylic acid copolymer. Among the supplements, powder-based samples had higher MPs (at the adult dosage suggested by the manufacturer) than gummy-based product. The average predicted ingestion of microplastics from these supplements (all nine samples) was 5.89 ± 2.89 particles day−1. The dietary exposure for children and adults ranged from 0.1–0.48 and 0.18–4.08 particles day−1, respectively. Based on the microplastic contamination factor (MCF), among the nine samples tested, 69.81% exhibited a moderate level, while 20.76% showed a significant level of microplastic contamination. The polymer risk index (pRi) indicates products with very high and high-risk categories. The possible sources of MPs contamination in the products were studied. To our knowledge, this is the first study to record and quantify the presence of MPs in dietary fiber supplements, which is a direct source of MPs exposure to humans via., ingestion.

Pulmonary Flora-Derived Lipopolysaccharide Mediates Lung-Brain Axis through Activating Microglia Involved in Polystyrene Microplastic-Induced Cognitive Dysfunction.

Microplastics (MPs) have been detected in the atmospheric and the human respiratory system, indicating that the respiratory tract is a significant exposure route for MPs. However, the effect of inhaled MPs on cognitive function has not been adequately studied. Here, a C57BL/6 J mouse model of inhalation exposure to polystyrene MPs (PS-MPs, 5 µm, 60 d) is established by intratracheal instillation. Interestingly, in vivo fluorescence imaging and transmission electron microscopy reveal that PS-MPs do not accumulate in the brain. However, behavioral experiments shows that cognitive function of mice is impaired, accompanied by histopathological damage of lung and brain tissue. Transcriptomic studies in hippocampal and lung tissue have demonstrated key neuroplasticity factors as well as cognitive deficits linked to lung injury, respectively. Mechanistically, the lung-brain axis plays a central role in PS-MPs-induced neurological damage, as demonstrated by pulmonary flora transplantation, lipopolysaccharide (LPS) intervention, and cell co-culture experiments. Together, inhalation of PS-MPs reduces cognitive function by altering the composition of pulmonary flora to produce more LPS and promoting M1 polarization of microglia, which provides new insights into the mechanism of nerve damage caused by inhaled MPs and also sheds new light on the prevention of neurotoxicity of environmental pollutants.

Characterization and ecological health risks of microplastics in the water and sediment of Xinyanggang River Estuary

ABSTRACT Microplastic (MP) pollution in aquatic environment has increased concerns. This study comprehensively examined properties and health risk to ecosystem of MPs in Xinyanggang River Estuary. Monthly sampling in 2023 detected MPs in water column (6.7 ± 0.55–11.6 ± 0.63 particles/L) and sediment (6.2 ± 0.78–10.2 ± 0.53 particles/g), with abundance peaking in summer, coinciding with the rainy season. The major features of the detected MPs included transparency and fiber, rayon, PVDF, PS, PE and PP composition. The dominant size fraction of detected MPs was 0.001–0.25 mm. Ecological risk assessment suggested relatively low load of MPs entering the Xinyanggang Estuary. However, polymer risk index (PRI) and potential ecological health risk index (PERI) suggested that MPs in Xinyanggang River are hazardous to ecosystem. This study firstly characterized MP contamination in Xinyangang River Estuary, and the provided results can guide the management of MPs in water environment more broadly.

Remediation of biochar-supported effective microorganisms and microplastics on multiple forms of nitrogenous and phosphorous in eutrophic lake

Lots of studies on eutrophication, but there is a lack of comprehensive research on the repair of multiple forms of nitrogen and phosphorus under combined heavy metals (HMs) pollution. This work investigated the various forms of nitrogen and phosphorus in the water-sediment systems of eutrophic lakes with the application of biochar, Effective Microorganisms (EMs) and microplastics, aiming to deliberate the repair behavior of multiple forms of nitrogen/phosphorus and the integrated repairment of these nutrients and HMs in different remediations. For amended-groups, the application of biochar-supported EMs (BE) achieved the most desirable remediation for removing nitrogen, phosphorus and HMs in water and improved their stability in sediment due to the improved microbial activity and the developed biofilm system created by biochar. The addition of aging microplastics (MP) obviously reduced the systematic levels of nitrogen, phosphorus and HMs due to the stimulation of microbial activity and the adsorption of biofilm/EPS, but its high movability also increased the Fe(II) and S(-II) levels and the pollutants' ecological risks in sediment. The co-application of BE and MP (MBE) destroyed the ecosystem and decreased the removal of nitrogen and phosphorus, while greatly removing HMs by the superfluous biofilms/EPS. The application of biochar (BC) preferentially adsorbed and degraded dissolved nitrogen and phosphorus, releasing HMs into water. From these amended-groups, it's also knew that the removal of nitrogen and phosphorus mainly came from the degradation/assimilation of NH3-N, SRP and dissolved matters, particularly those molecular weight below 3 kDa; the higher removal of phosphorus than nitrogen was attributed to the coprecipitation of Fe-S-P hydroxides and the adsorption of particulates; however, the colloidal (3–100 kDa) nitrogen and phosphorus had low accessibility and bioavailability, and it also showed the competitive adsorption with colloidal HMs, causing their relatively low removal in water. This study provides insight into the comprehensive repair of nitrogen, phosphorus and HMs in various forms by biochar-immobilized microbes and the influence of microplastics on nutrients and HMs in eutrophic lakes.

Origin of biomarkers (PAH, n-alkane, hopane, estrane) in different colors of plastic resin pellets and surface sediments from coastal area of the Makuran-Oman Sea

The unique attributes of the study area, situated near the Strait of Hormuz—an extensively utilized oil shipping corridor for Iran and neighboring Arabian nations—encompass oil extraction and exploitation, the establishment of an oil export hub, the advancement of petrochemical industries, as well as tourism and transportation activities. This research represents the first examination of the sources of plastic resin pellet release, addressing both local and non-local contributions. To conduct this study, samples of plastic resin pellet and coastal and intertidal surface sediments were collected from seven stations on the shores of the Oman Sea in Hormozgan province (Sirik, Garook, Ziarat, Karpan, Koohestak, Gohardo, and Kargan) with four replications to determine the origin and spatial distribution pattern of hydrocarbons and the diffusion source of plastic resin pellets (offshore or regional). Plastic resin pellets were separated based on color (white, yellow, brown, and black). Soxhlet was used to extract hydrocarbons, two stages of column chromatography were used to separate compounds, and gas chromatography–mass spectrometry (GC–MS) was used to identify and determine their concentration. The total n-alkanes concentration ranged from 2940 to 18,711 (μg/g) in coastal surface sediments, from 19,721–1678 (μg/g) in intertidal surface sediments, and from 11,481.50 to 55,601.41 (μg/g) in plastic resin pellets. A similar trend was found for the total PAH concentration which ranged from 135.57 to 3890.62 (ng/g) in coastal sediments, from 1820.28 to 6579.55 (ng/g) in intertidal sediments, and from 3714.19 to 66/1920451 (ng/g) in plastic resin pellets. According to the sediment pollution criteria, a high pollution level was assessed in most of the stations. In most of the surface sediments and plastic resin pellets, the presence of unresolved complex mixture (UCM), the carbon preference index (CPI) lower than 1, and the diagnostic ratios of PAH, hopane, and sterane compounds indicated petrogenic origin for hydrocarbons. The results of principal component analysis based on 16 diagnostic ratios of PAH, n-alkane, hopane, and sterane compounds showed that brown and black plastic resin pellets were placed in a different group than the coastal and intertidal sediments and white and yellow plastic resin pellets. Most likely, the diffusion source of brown and black plastic resin pellets is different and through open water.

Organ-specific bioaccumulation of microplastics in market fish of Dhaka and size-dependent impacts of PVC microplastics on growth of Anabustestudineus

Microplastics (MPs), a growing environmental concern with potential ecotoxicological risks, are ubiquitous in aquatic environment. This study investigated the organ-specific distribution and variation of MPs in commercially caught fishes (7 species, 140 individuals) collected from Dhaka's two main fish distribution hubs (Uttara and Jatrabari). Additionally, the impact of different-sized MPs on fish growth (Anabas testudineus) was examined in a control experiment. Results revealed that kidneys of market fish bioaccumulated the highest concentration of MPs (average, 59.1 MPs/g), followed by liver (24.6 MPs/g) and intestine (18.6 MPs/g). On average, fish from Uttara had a higher MPs concentration (36 MPs/g) compared to Jatrabari (25 MPs/g). Among fish species, Glossogobius giuris showed the highest MPs bioaccumulation due to its feeding habits and morphology. Fiber-shaped MPs were most prevalent in all fishes (79–93%) except Glossogobius giuris (fragments, 51%). Fourier-transform infrared spectroscopy (FTIR) analysis identified 19 different polymer types, with high density polyethylene (HDPE), ethylene vinyl acetate (EVA) and polyamide (PA) being commonly found in all organs. The experimental study confirmed that large-sized PVC MPs (1.18 mm-300 μm) had a greater negative impact on fish growth (length) and caused more physical deformities (particularly intestinal injuries) compared to small-sized PVC MPs (150 μm–75 μm). Moreover, fish exposed to larger diameter MPs experienced highest physical weight and depth loss among exposed groups. Large-sized PVC MPs bioaccumulated highest in fish compared to small-sized PVC MPs. Similar to market fish, kidney in the experimental fish had the highest MPs bioaccumulation (6.5 MPs/g), followed by liver (5.2 MPs/g) and intestine (4.8 MPs/g), with a dominance of fibers despite the presence of high concentration of fragments in the food source. Statistical analysis also supported a clear correlation between increasing MPs size and adverse effects on fish growth and health. Urgent action is needed to curb microplastic pollution and protect ecosystems and human health.

The addition of humic acid into soil contaminated with microplastics enhanced the growth of black gram (Vigna mungo L. Hepper) and modified the rhizosphere microbial community.

Microplastics have polluted agricultural soils, posing a substantial risk to crop productivity. Moreover, the presence of microplastic pollution has caused a disturbance in the composition of the microbial community in the soil surrounding plant roots, therefore impacting the growth of beneficial bacteria. A study was conducted to examine if humic acid (HA) can counteract the harmful effects of microplastics (MPs) on the growth of black gram crops and the composition of the rhizosphere soil microbial community, to reduce the negative impacts of microplastics on these microorganisms and crops. The research was carried out using mud pots and the plastic utilized for the experiment consisted of 60% high-density polyethylene (HDPE) and 40% polypropylene (PP). The soil was enriched with lignite-based potassium humate, which had a pH range of 8.0-9.5 and with 65% humic acid. The experiment consisted of six treatments: T1, which served as the control without HA and MP; T2, which involved the use of HA at a concentration of 0.15% w/w; T3, which involved the use of MP at a concentration of 0.2% w/w; T4, which involved the use of MP at a concentration of 0.4% w/w; T5, which involved the combination of HA at a concentration of 0.15% w/w and MP at a concentration of 0.2% w/w; and T6, which involved the combination of HA at a concentration of 0.15% w/w and MP at a concentration of 0.4% w/w. The plant growth characteristics, including germination percentage, nodule number, and chlorophyll content, were measured. In addition, the DNA obtained from the rhizosphere soil was analyzed using metagenomics techniques to investigate the organization of the microbial population. Seedlings in soil polluted with MP exhibited delayed germination compared to seedlings in uncontaminated soil. Following 60days of growth, the soil samples treated with T5 (0.2% MP and 0.15% HA w/w) had the highest population of bacteria and rhizobium, with counts 5.58 ± 0.02 and 4.90 ± 0.02CFUg-1 soil. The plants cultivated in T5 had the most elevated chlorophyll-a concentration (1.340 ± 0.06mgg-1), and chlorophyll-b concentration (0.62 ± 0.02mgg-1) while those cultivated in T3 displayed the lowest concentration of chlorophyll-a (0.59 ± 0.02mgg-1) and chlorophyll-b (0.21 ± 0.04mgg-1). Within the phylum, Proteobacteria had the highest prevalence in all treatments. However, when the soil was polluted with MPs, its relative abundance was reduced by 8.4% compared to the control treatment (T1). Conversely, treatment T5 had a 3.76% rise in relative abundance when compared to treatment T3. The predominant taxa found in soil polluted with MP were Sphingomonas and Bacillus, accounting for 19.3% of the total. Sphingomonas was the predominant genus (21.2%) in soil polluted with MP and supplemented with humic acid. Humic acid can be used as a soil amendment to mitigate the negative effects of MPs and enhance their positive advantages. Research has demonstrated that incorporating humic acid into soil is a viable method for maintaining the long-term integrity of soil's physical, chemical, and biological characteristics.

Characterization of microplastics in soil, leachate and groundwater at a municipal landfill in Rayong Province, Thailand

Recent years have witnessed a dramatic increase in global plastic production, leading to heightened concerns over microplastics (MPs) contamination as a significant environmental challenge. MP particles are ubiquitously distributed across both continental and marine ecosystems. Given the paucity of research on MPs in Thailand, particularly regarding MPs contamination in terrestrial environments, this study focused on investigating the distribution and characteristics of MPs in a landfill area. We collected 15 soil samples, 2 leachate samples, and 5 groundwater samples from both inside and outside a municipal landfill situated in the urbanized coastal region of Rayong Province. Our findings revealed variability in MPs concentration across different sample types. In soil, the MP count ranged from 240 to 26,100 pieces per kg of dry soil, 58.71 % of all sample sizes are lower than 0.5 mm. Similarly, the size found in the leachate sample, and the average MP in the leachate samples was 139 pieces per liter of MPs. The groundwater samples showed a fluctuation in MPs count from 26 to 94 pieces per liter, and the size of MPs ranged mostly from 0.5 to 1 mm. The predominant forms of MPs identified were sheets, followed by fragments, fibers, and granules. According to μ-FTIR analysis, the majority of the MPs were composed of polyethylene and polypropylene, commonly used in plastic packaging and ropes. The observed high concentrations and extensive distribution of MP contamination underscore the urgency for further studies and effective management strategies to mitigate the adverse impacts of this pollution on various organisms and ecosystems.

Sandstorms contribute to the atmospheric microplastic pollution: Transport and accumulation from degraded lands to a megacity

Surface dust from degraded lands is a major global aerosol source, mobilized by meteorological events like sandstorms. Microplastics (MPs) in dust can be enriched in the atmosphere and transported over long distances to sensitive regions during sandstorms. This study was conducted in a megacity frequently impacted by sandstorms in spring, exploring the influx, characteristics, enrichment mechanism, and transport pathway of sandstorm-derived MPs. The deposition rate of these MPs reached 1823.65 ± 892.53 items·m-2·d-1, predominantly consisting of low-density polymers and those mainly used in synthetic fiber, with an average size of 60.75 μm. Compared to MPs in annual atmospheric deposition, these MPs were smaller and contained a higher proportion of potentially harmful polymers. These factors could increase exposure risks for residents from sandstorm-derived MPs, along with distinct meteorological and ecological effects. Backward trajectory analysis suggested the observed sandstorms originated from the Mongolian Plateau, over 1000km away. Comparisons of MPs from surface-collected dust on the Mongolian Plateau with sandstorms-delivered MPs revealed the transport was determined by MP shape, size, and density. This study highlights the critical role of sandstorms in the MP atmospheric cycling, emphasizing the extensive impacts of MPs and the need for coordinated mitigation efforts across regions.