Microplastic Retention Research Articles

Sediment-associated microplastics in Chilika lake, India: Highlighting their prevalence, polymer types, possible sources, and ecological risks

The primary objective of this research was to assess microplastics (MPs) in the sediments of Chilika lake. MPs were extracted from 22 sediment samples using the density separation method combined with vacuum pump filtration. A stereo-zoom microscope and Raman spectroscopy were employed to identify the sediment-associated MPs. The total MPs collected from all 22 sites was 440 ± 3.53 particles kg−1 wet sediments, with sizes ranging between 50 and 500 μm. In terms of morphology, fibers and fragments emerged as the dominant MP types, with counts of 210 ± 1.66 and 175 ± 1.76 particles kg−1 wet sediments, respectively. Raman spectroscopy verified the presence of various MP polymers in the sediments, predominantly HDPE (37 %), followed by PS (20 %), PET (18 %), PA (11 %), PP (7 %), and PC (7 %). A notable color variation was observed in MPs; black being the most prevalent (38.8 %), succeeded by blue (19.5 %), green (11.8 %), white (11.5 %), red (10.6 %), and transparent (7.5 %). ANOVA results indicated significant (p > 0.05) variations in MP abundance across the 22 sampling locations. However, principal component analysis (PCA) and multiple regression analysis indicated that water quality parameters did not significantly influence MP abundance, yet it was found that MP retention was higher in fine-grained sediments like clay and silt. The leading sources of MPs in Chilika lake were found to be aquafarming, trailed by river and sewage discharges, fishing activities, antifouling coatings and tourism. Additionally, the pollution load index (PLI) was employed to gauge the ecological risks, categorizing the lake under risk category 1, which implies a minimal level of MPs pollution. This research aims to serve as an early warning system for MPs pollution in productive brackish water habitats globally, including Chilika lake, guiding policymakers towards appropriate management strategies and preventive measures.

Microplastic retention in marine vegetation canopies under breaking irregular waves

The present study provides indications and underlying drivers of wave-induced transport and retention potential of microplastic particles (MP) in marine vegetation canopies having different densities. The anthropogenic occurrence of MP in coastal waters is well documented in the recent literature. It is acknowledged that coastal vegetation can serve as a sink for MP due to its energy dissipating features, which can mimic a novel ecosystem service. While the transport behavior of MP in vegetation has previously been investigated to some extent for stationary flow conditions, fundamental investigations for unsteady surf zone flow conditions under irregular waves are still lacking. Herein, we demonstrate by means of hydraulic model tests that a vegetation's retention potential of MP in waves increases with the vegetation shoot density, the MP settling velocity and decreasing wave energy. It is found that particles migrating by traction (predominantly in contact with the bed) are trapped in the wake regions around a canopy, whereas suspended particles are able to pass vegetated areas more easily. Very dense canopies can also promote the passage of MP with diameters larger than the plant spacing, as the canopies then show characteristics of a solid sill and avoid particle penetration. The particle migration ability through a marine vegetation canopy is quantified, and the key drivers are described by an empirical expression based on the particle settling velocity, the canopy length and density. The findings of this study may contribute to improved prediction and assessment of MP accumulation hotspots in vegetated coastal areas and, thus, may help in tracing MP sinks. Such knowledge can be considered a prerequisite to develope methods or new technologies to recover plastic pollutants and rehabilitate valuable coastal environments.

Retention and excretion of microplastics by Yellow Mealworm (Tenebrio molitor) larvae reared on an amino formaldehyde polymer microbeads contaminated substrate

Abstract Yellow mealworm (Tenebrio molitor L., TM), one of the main cultured insect species, is used for feed and food. Larval stages of this species can be reared on several substrates, including grains and industrial by-products. However, this species may potentially accumulate contaminants from the substrate, including microplastics (MPs), which may represent a potential hazard for its utilization in food chain. Evidences for plastic degradation by mealworms have been reported, while there are few information about the retention of microplastics in the body and tissues of this species. The aim of the present study was to assess whether TM larvae reared on a MPs-contaminated substrate were able to retain MPs in body tissues and to evaluate the retention and excretion rate after fasting for 24 and 48 hours. For this purpose, fluorescent amino formaldehyde polymer microbeads (1-5 μm) were used to simulate a MPs contamination in the substrate used for larvae rearing. A relevant concentration of MPs were found in the gut and were associated with ingested feed. However, microscopic analyses indicated that the gut acts as a simple transit site and a barrier towards MPs migration in tissues. A marked reduction of MPS content was highlighted in larvae after fasting, even though a 48-hours fasting period was not sufficient to completely depurate insect gut from MPs. Results obtained in the present study suggest that the polymer microbeads used are recalcitrant to digestion by TM larvae, and show the relevant ability of depuration from MPs of this species. Taken together the results showed the suitability of TM to be reared on MPs contaminated substrates since larvae survival and growth resulted not hampered by the MPs presence and open cues on the fasting period able to completely depurate insect body from MPs residues.

Microplastic trapping efficiency and hydrodynamics in model coral reefs: A physical experimental investigation

Coastal ecosystems, such as coral reefs, are vulnerable to microplastic pollution input from proximal riverine and shoreline sources. However, deposition, retention, and transport processes are largely unevaluated, especially in relation to hydrodynamics. For the first time, we experimentally investigate the retention of biofilmed microplastic by branching 3D printed corals (staghorn coral Acropora genus) under various unidirectional flows (U = {0.15, 0.20, 0.25, 0.30} ms−1) and canopy densities (15 and 48 corals m−2). These variables are found to drive trapping efficiency, with 79–98% of microplastics retained in coral canopies across the experimental duration at high flow velocities (U = 0.25–0.30 ms−1), compared to 10–13% for the bare bed, with denser canopies retaining only 15% more microplastics than the sparse canopy at highest flow conditions (U = 0.30 ms−1). Three fundamental trapping mechanisms were identified: (a) particle interception, (b) settlement on branches or within coral, and (c) accumulation in the downstream wake region of the coral. Corresponding hydrodynamics reveal that microplastic retention and spatial distribution is modulated by the energy-dissipative effects of corals due to flow-structure interactions reducing in-canopy velocities and generating localised turbulence. The wider ecological implications for coral systems are discussed in light of the findings, particularly in terms of concentrations and locations of plastic accumulation.

To what extent is blue mussels caging representative of microplastics in the natural environment?

Bivalves have gained prominence in active biomonitoring of microplastics (MPs) pollution. Nevertheless, critical questions persist regarding blue mussels' selectivity and representativeness of the presence of microplastics in the natural environments. In this current study, we explored short- and long-term exposure durations for caged mussels, aiming to establish the minimum period required for them to attain a steady-state in microplastics retention and investigate their selectivity in a real-world context. Various deployment periods (1, 2, and 5 weeks) were tested, with concurrent collection of MPs from the surrounding water each week. The results revealed a significant increase in ingested MPs, reaching a threshold of approximately 1.4 MPs per gram of wet weight during the fifth week of caging. The characteristics of MPs found in mussels exhibited some differences from those collected in the surrounding waters and were less temporally variable. Notably, the collected caged mussels demonstrated a tendency to retain smaller particles (<80 μm). This study underscores complex processes governing MPs selection in natural environments and the need for further research to gain a more comprehensive understanding of the conditions and suitability of mussels as bioindicators for assessing MPs pollution.

Retention of microplastics by interspersed lagoons in both natural and constructed wetlands

Natural wetlands, the transitional zones found between the land and the sea, are considered hot spots for plastic accumulation. Constructed wetlands (CW) attempt to mimic these natural wetlands in order to provide potential Nature-Based Solutions (NBS) for reducing microplastic (MP) contamination in wastewater treatment plants, and mitigating MP pollution in rivers. In this work, the role played by an interspersed lagoon surrounded by aquatic vegetation (Juncus Maritimus) in retaining MP was investigated using experimental laboratory simulations. Four MP types (125–500 μm and 500–1000 μm PA fragments, 2 mm PET fibers and 5 mm PET fibers) along with suspended sediments were injected into the model wetland to study their transport throughout the system. Five different vegetated patch lengths surrounding the lagoon were considered (LP). Results showed that aquatic vegetation protected wetlands from PA fragments and PET fibers by increasing the dispersion of the particle-laden flow and consequently MP sedimentation. When the use of vegetated patches was coupled with an interspersed lagoon, MP retention rates were maximized (with total percentages of 88 ± 3 % and 99 ± 1.5 % for PA fragments and PET fibers, respectively), suggesting that CW are a potential NBS for trapping MP pollution from specific sources.

Retention efficiency for microplastic in a landscape estimated from empirically validated dynamic model predictions

Soils are recipients of microplastic that can be subsequently transferred to the sea. Land sources dominate inputs to the ocean, but knowledge gaps about microplastic retention by land hinder assessments of input rates. Here we present the first empirical evaluation of a dynamic microplastic fate model operating at landscape level. This mechanistic model accounts for hydrology, soil and sediment erosion, particle characteristics and behavior. We predict microplastic concentrations in water and sediments of the Henares river (Spain) within the measurement uncertainty boundaries (error factors below 2 and 10, respectively). Microplastic export from land and discharge by river fluctuates in a non-linear manner with precipitation and runoff variability. This indicates the need of accurate dynamic descriptions of soil and stream hydrology even when modeling microplastic fate and transport in generic scenarios and at low spatio-temporal resolution. A time-averaged landscape retention efficiency was calculated showing 20–50% of the microplastics added to the catchment over a multiannual period were retained. While the analysis reveals persistent uncertainties and knowledge gaps on microplastic sources to the catchment, these results contribute to the quantitative understanding of the role of terrestrial environments in accumulating microplastics, delaying their transport to the sea.

Retention of microplastics and tyre wear particles in stormwater ponds

Stormwater runoff from urban areas contain a wide variety of pollutants which is typically managed using stormwater retention ponds. However, their performance with regards to emerging pollutants such as microplastics and tyre wear material remains unclear. In this study, samples of effluent water and sediments from four stormwater retention ponds were analysed for their content of microplastics and tyre wear material. Microplastics were analysed using state-of-the-art hyperspectral imaging technique while tyre wear material was analysed using pyrolysis-GC–MS. Microplastics were recovered in all samples and the mass balance revealed that on average 88% of small microplastics (<500 µm) were retain in the ponds while the removal efficiency for large microplastics (>500 µm) was 95%. Tyre wear material was identified in all sediment samples but found below the detection limit in three out of four effluent samples. On average 95% of the tyre wear material was removed by the retention ponds. The results from this study show that stormwater retention ponds are very effective in removing microplastics as well as tyre wear material from stormwater runoff.

Diel Pattern of Microplastic Residues in Zebrafish.

As one of the emerging pollutants, microplastics (MPs) can be taken up by aquatic organisms through ingestion. However, little is known about the uptake pattern in organisms over time and the associated mechanisms of retention patterns. The present study aims to elucidate these patterns in fish, their relationship with light/dark conditions, and examine the uptake kinetic process of small-sized plastic pollutants, especially during the long-neglected dark period. Zebrafish were sampled every 2 h during the light and dark periods after exposure to an environmentally relevant concentration (100 items/L) of MPs. The results demonstrated that MP residues in zebrafish decreased during the dark period rather than increased over time. The MP retention rhythm and the swimming behavior of exposed zebrafish displayed a statistically significant light/dark variation. Moreover, a very strong and statistically significant positive correlation was found between the swimming speed of zebrafish and the number of MP residues in the gastrointestinal tracts of zebrafish. These results clearly demonstrate that fibrous MP residues in the fish have a discernible diel pattern. This work improves the understanding of the dynamic residual process of MPs in organisms and calls for further in-depth circadian toxicokinetic studies to better suit particle pollutants.

Integrated numerical modeling to quantify transport and fate of microplastics in the hyporheic zone.

Despite the significance of rivers and streams as pathways for microplastics (MP) entering the marine environment, limited research has been conducted on the behavior of MP within fluvial systems. Specifically, there is a lack of understanding regarding the infiltration and transport dynamics of MP across the streambed interface and within the hyporheic sediments. In this study, transport and retention of MP are investigated using a new numerical modeling approach. The model is built as a digital twin of accompanying flume experiments, which are used to validate the simulation results. The model accurately represents particle transport in turbulent water flow and within the hyporheic zone (HZ). Simulations for transport and infiltration of 1µm MP particles into a sandy streambed demonstrate that the advection-dispersion equation can be used to adequately represent particle transport for pore-scale sized MP within the HZ. To assess the applicability of the modeling framework for larger MP, the experiment was repeated using 10µm particles. The larger particles exhibited delayed infiltration and transport behavior, and while the model successfully represented the spatial extent of particle transport through the HZ, it was unable to fully replicate hyporheic transit times. This study is the first to combine explicit validation against experimental data, encompassing qualitative observations of MP concentration patterns and quantification of fluxes. By that, it significantly contributes to our understanding of MP transport processes in fluvial systems. The study also highlights the advantages and limitations of employing a fully integrated modeling approach to investigate the transport and retention behavior of MP in rivers and streams.

Inferring microplastics origins in the Mediterranean Sea by coupling modelling and in-situ measurements

This work focuses on the dynamics and retention of microplastics (MP) in the Mediterranean. MP manta-net trawls were performed in autumn 2019 north of the Balearic Islands and along the Balearic Front (BF). Lagrangian modelling was used to find the MP collected origin during the campaign. These combined results show that North of Mallorca is a temporary retention zone of 3 months variability, with MP origin being the Northern Current (NC) and the Gulf of Lion (GOL). Retention processes were less clear along the BF, due to frontal dynamics together with the strong northerly winds. However, it appears that the origin can differ between the North (i.e. the large North-Westerly basin, including the GOL and the NC path) and the South (short distances around the zone) of this front. In both areas, the wind and the current variability are strongly conditioning the existence and position of the MP concentration zones.

The fate of microplastics from municipal wastewater in a surface flow treatment wetland

Microplastics (MPs) are an anthropogenic pollutant of emerging concern prominent in both raw and treated municipal wastewater as well as urban and agricultural run-off. There is a critical need for the mitigation of both point- and diffuse sources, with treatment wetlands a possible sustainable nature-based solution. In this study, the possible retention of MPs in treatment wetlands of the widely used surface flow (SF) type was investigated. In- and outflow water, as well as atmospheric deposition, at a full-scale reed-based SF wetland (operating as a polishing phase of municipal wastewater treatment) was analyzed for MPs in a size range of 25–1000 μm. FPA-based μFT-IR spectroscopic imaging was used in combination with automated data analysis software, allowing for an unbiased assessment of MP numbers, polymer types and size distribution.Inflow water samples (secondary treated wastewater) contained 104 MPs m−3 and 56 MPs m−3 in sampling campaigns 1 and 2, respectively. Passage through the SF wetland increased the MP concentration in the water by 92 % during a rain intense period (campaign 1) and by 43 % during a low precipitation period (campaign 2). The MP particle numbers, size and polymer type distribution varied between the two sampling campaigns, making conclusions around the fate of specific types of MPs in SF wetlands difficult.Atmospheric deposition was measured to be 590 MPs m−2 week−1 during the rain-intense period. Our findings point towards atmospheric deposited MPs as an important factor in the fate of MPs in SF wetlands, causing an increase of MP concentrations, and potentially explaining the variations observed in MP concentrations in wetland effluent and removal efficiency. Furthermore, atmospheric deposition might also be a reason for the considerable inter-study variation regarding MPs removal efficiency in SF wetlands found in the available literature.

How effective is the retention of microplastics in horizontal flow sand filters treating stormwater?

Microplastics accumulate in stormwater and can ultimately enter freshwater recipients, and pose a serious risk to aquatic life. This study investigated the effectiveness of lab-scale horizontal flow sand filters of differing lengths (25, 50 and 100 cm) in retaining four types of thermoplastic microplastics commonly occurring in stormwater runoff (polyamide, polyethylene, polypropylene, and polyethylene terephthalate). Despite the differences in particle shape, size and density, the study revealed that more than 98% of the spiked microplastics were retained in all filters, with a slightly increased removal with increased filter length. At a flow rate of 1 mL/min and after one week of operation, 62–84% of the added microplastics agglomerated in the first 2 cm of the filters. The agglomerated microplastics included 96% of high-density fibers. Larger-sized particles were retained in the sand media, while microplastics smaller than 50 μm were more often detected in the effluent. Microplastics were quantified and identified using imaging based micro Fourier Transform Infrared Spectroscopy. The efficient retention of microplastics in low-flow horizontal sand filters, demonstrated by the results, highlights their potential importance for stormwater management. This retention is facilitated by various factors, including microplastic agglomeration, particle sedimentation of heavy fibers and favorable particle-to-media size ratios.

Levels and composition of microplastics and microfibers in the South Saskatchewan River and stormwater retention ponds in the City of Saskatoon, Canada.

In recent decades, contamination of the environment with microplastics and microfibers has been recognized as a pervasive and ubiquitous issue of global concern. While much research in this field has been undertaken in marine environments, more recent studies have identified rivers as major conveyors of plastic pollution from terrestrial into marine systems. However, reports on the levels and composition of microplastic and microfiber contamination in rivers of the Canadian prairie region, specifically the South Saskatchewan River (SSR), are scarce, which leaves this vital source of water for societies and ecosystems in a vulnerable state. To fill this gap, we obtained samples from seven sites along the Saskatchewan portion of the SSR, as well as three stormwater retention ponds (SRP) in the city of Saskatoon during the spring, summer, and fall of 2020. We used optical and Raman microscopy to enumerate and characterize particles in these samples. Total levels of particles and fibers in all samples ranged from 32 to 116 particles m-3. Most particles (approximately 77%) were natural fibers, while polymers accounted for the remaining 33%. Average microplastic levels were lower (3.18 ± 3 particles m-3) downstream of Lake Diefenbaker, a large reservoir on the SSR, compared to upstream (12.0 ± 9 particles m-3). Retention of microplastics in the reservoir could explain the lower mean microplastic concentration of 4.43 ± 3 particles m-3 recorded in the SSR compared to mean concentrations of 26.2 ± 18 particles m-3 reported in the North Saskatchewan River, which is not dammed. This study is among the first to describe microplastic and microfiber levels in the SSR and thereby helps improve our understanding of this pervasive environmental contaminant on the Canadian prairies.

Scavenging microplastics and heavy metals from water using jujube waste-derived biochar in fixed-bed column trials

Extensive production and utilization of plastic products have resulted in the generation of microplastics (MPs), subsequently polluting the environment. The efficiency of biochars (BCs) derived from jujube (Ziziphus jujube L.) biomass (300 °C and 700 °C) for nylon (NYL) and polyethylene (PE) removal from contaminated water was explored in fixed-bed column trials. The optimum pH for the removal of both MPs was found 7. Both of the produced biochars demonstrated >99% removal of the MPs, while the sand filter exhibited a maximum of 78% removal of MPs. BC produced at 700 °C (BC700) showed 33-fold higher MPs retention, while BC produced at 300 °C (BC300) exhibited 20-fold higher retention, as compared to sand filters, indicating the higher efficiency of BC produced at higher pyrolysis temperature. Entrapment into the pores, entanglement with flaky structures of the BCs, and electrostatics interactions were the major mechanism for MPs retention in BCs. The efficiency of MPs-amended BCs was further explored for the removal of Pb(II) and Cd(II) in fixed-bed column trials. BC700 amended with PE and NYL exhibited the highest 50% breakthrough time (2114.23 and 2024.61 min, respectively, for Pb(II) removal and 2107.92 and 1965.19 min, respectively, for Cd(II) removal), as compared to sand filters (38.07 and 60.49 min for Pb(II) and Cd(II) removal, respectively). Thomas model predicted highest adsorption capacity was exhibited by BC700 amended with PE (584.34 and 552.80 mg g−1, for Pb(II) and Cd(II) removal, respectively), followed by BC700 amended with NYL (557.65 and 210.59 mg g−1 for Pb(II) and Cd(II) removal, respectively). Therefore, jujube waste-derived BCs could be used as efficient adsorbents to remove PE and NYL from contaminated water, while MPs-loaded BCs can further be utilized for higher adsorption of Pb(II) and Cd(II) from contaminated aqueous media. These findings suggest that BC could be used as an efficient adsorbent to remove the co-existing MPs-metals ions from the environment on a sustainable basis.

Influence of tourism on microplastic contamination at wastewater treatment plants in the coastal municipality of Chiclana de la Frontera

The tourism is one of the most important sources of the economy in the Bay of Cadiz. Specifically, the municipality of Chiclana de la Frontera, with a population lower than 90,000 citizens, located in the southeast of Spain. During the summer season the population duplicates leading to an increment in flow at wastewater treatment plants (WWTPs). These facilities have been reported as a source of microplastics (MPs) into marine ecosystems, therefore the aim of the present study is to investigate if the tourism affects the presence, discharge and in the receiving environment. Samples were taken at the influent and effluent of the municipal WWTPs (one located at the urban area and other located at resort area) during 2021 (including low and high season). MPs were collected and extracted from wastewater matrixes following the method recommended by the National Oceanic and Atmospheric Administration and UTS treatment to reduce organic matter and cellulose, respectively. The analysis of the samples was performed according to their abundance, shape, size, and type of polymer, along with the removal rates of MPs at WWTPs. The results showed heterogeneous MPs abundance ranging from 1246.4 to 345.7 MPs/L and 72.9 to 4.2, in the influent and effluent, respectively, increasing the presence of MPs at resort WWTP during high season. Fibers were the predominant shape within all the samples. A total of 17 polymers were identified, by ATR-FTIR, where Acrylates, PE and PA were the largest polymers found. Despite the high MPs retention performance of the WWTPs analyzed (84.1–99.3 %), a combined contribution of approximately 1.4 × 107–5.9 × 108 MPs/d to the aquatic environment was estimated. Finally, these results indicate that the increase of MPs in the wastewater at WWTP-B was related with the population increase as a consequence of summer tourism.

Assessing the Impact of Microplastic Filaments Contaminated with PAHs on Mytilus coruscus Larvae through Surface Contact.

In recent years, microplastics have been of great concern in environmental and health research. In field surgeries and laboratory investigations, research interests were focused on the retention of microplastics inside of animals by ingestion and the series of negative effects after that. However, such large plastic debris and filaments are hardly eaten by small animals, like zooplankton, planktonic larvae, etc. In this study, the surface contact between plastic filaments contaminated with polycyclic aromatic hydrocarbons (PAHs) and mussel pediveliger larvae has been investigated to figure out the effects of "non-digestive tract route of exposure" on subject animals. In a 1600 mL artificial seawater medium, high mortalities of mussel larvae were recorded after being exposed to two PAHs-contaminated (benzo[α]pyrene (BaP) and phenanthrene (Phe)) filaments for 5 days, 68.63% for BaP and 56.45% for Phe on average. We suggest that the surface contact was the dominant pathway to transfer PAHs from contaminated filaments to larvae and that the risk of contaminated plastic ropes transferring hydrophobic organic compounds (HOCs) to larvae in mussel aquaculture should be taken seriously.

Seasonal pulse effect of microplastics in the river catchment-From tributary catchment to mainstream

Rivers have received extensive attention as a major pathway for microplastics (<5000 μm) from land to ocean. This study investigated the seasonal variation of microplastic contamination in surface water of the Liangfeng River catchment, a tributary of the Li River in China, based on a fluorescence-based protocol, and further explored the migration process of microplastic in the river catchment. The abundance of microplastics (50–5000 μm) was (6.20 ± 0.57)–(41.93 ± 8.13) items/L, of which 57.89–95.12% were small-sized microplastics (<330 μm). The microplastic fluxes in the upper Liangfeng River, lower Liangfeng River, and upper Li River were (14.89 ± 1.24) × 1012, (5.71 ± 1.15) × 1012, and (1.54 ± 0.55) × 1014 items/year, respectively. The 3.70% of microplastic load in the mainstream came from the tributary input. Fluvial processes can effectively retain 61.68% of microplastics in the surface water of river catchments, especially for small-sized microplastics. The rainy season is the main period of microplastic retention (91.87%) in the tributary catchment by fluvial processes, while exporting 77.42% of one-year microplastic emissions from the tributary catchment into the mainstream. This study is the first to reveal the transport characteristics of small-sized microplastics in river catchments based on flux variation, which not only can partly explain the “missing small-sized microplastic fraction” in the ocean, but also contribute to improving microplastic model.

Predicting microplastic masses in river networks with high spatial resolution at country level

Microplastics are a ubiquitous contaminant of natural waters, and a lot of field monitoring is currently performed. However, what is missing so far is a general understanding how emissions of microplastics are linked to environmental exposure, especially on larger geographic scales such as countries. Here we coupled a high-resolution microplastic release model with a fate model in rivers and lakes and parameterized it for Switzerland on a country scale to predict masses of microplastics in each river section for seven different polymers. The results show that catchment characteristics, for example, distribution of releases within the catchment, location and size of lakes or river connections, are as important as polymer properties such as density. There is no simple linear function of microplastic retention within a catchment in dependency of river length to the outlet. Instead, we found that different catchments cover a wide range of retained fractions for microplastics. Consequently, we argue that the availability and use of spatially distributed release data and performing modelling on high spatial resolution is of importance when estimating concentrations of microplastics in large areas such as countries.

No microplastics detected in the first assessment of Atlantic walrus stomachs from Nunavut, Canada

As plastic pollution continues to persist at a global level, the Arctic has drawn increased research interest as a possible sink for marine pollutants. Plastic and microplastics are highly durable and can be transported across vast distances. To date, only a handful of studies have directly assessed microplastics in Arctic mammals. In Canada, it is still unclear whether they show a concrete propensity for microplastic retention and ingestion. Atlantic walruses ( Odobenus rosmarus rosmarus (Linnaeus, 1758)) are economically and culturally important for Inuit and are key predators in Arctic marine ecosystems. Here, we present the first assessment of microplastic pollution in Canadian walruses and the first gastrointestinal assessment of microplastic in walruses globally. Since microplastics accumulate in benthic sediment and animals, we expected that walruses may ingest and retain microplastic contaminants when sifting in search of prey or when eating contaminated bivalves and invertebrates. We detected no microplastics ≥80 µm in our evaluation of 36 walruses from five communities in NU, Canada. Our results suggest that walruses in this region do not retain microplastic particles ≥80 µm in their stomachs, which is consistent with findings in other pinnipeds that have been evaluated in Arctic Canada.