Microplastic Load Research Articles

Sequestration and export of microplastics in urban river sediments

In rivers, riverbeds are considered to have dual properties as a short-term sink and a source of further mobilization for microplastics. To better understand the sources, storage, and fate of microplastics in river systems, this study quantified the formation of microplastic hotspots in riverbeds and seasonal variations in microplastic inventories in riverbeds, especially for small-sized microplastics (<330 µm), with a fluorescence-based protocol. This study provides first-hand measured evidence for the sequestration of microplastics in the riverbed under low-flow conditions and its export from the riverbed under high-flow conditions. The results show that riverbeds in urban areas are still hotspots for microplastic pollution and that high inputs of urban microplastics control microplastic load in its downstream areas. Seasonal rainfall exported 34.86 % (equivalent to 4.34 × 1011 items/8.57 t) of microplastic pollution from the riverbed, and its removal capacity may be related to the rainfall intensity. Wider riverbeds are conducive to the formation of microplastic hotspots due to the flow slow down. Most importantly, rainfall-driven scouring of the riverbed can enhance the pollution of small-sized microplastics in the riverbed, especially the smallest-size microplastics (<100 µm). Therefore, this study not only contributes reliable information about the sequestration and export of microplastics in the riverbed, but also provides a possible mechanism to explain the lack of small-sized microplastics (<330 µm) in the ocean.

Shape- and polymer-considered simulation to unravel the estuarine microplastics fate

Environmental microplastics (MPs) constitute various sizes, polymers, and shape components. In estuaries, such differences are related to the reliability of assessing the seaward fate of MPs, aggregation hotspots, and ecological risks. This study sets the MP particle mass gradient using the shape factor and size probability density function to categorically estimate the MP load in the surface layer of the Yangtze River Estuary (YRE), which is the largest contributor of plastics to the sea. During the high plastic input period in July, the optimized estimated MP load through the surface layer of the YRE was 9766 kg/month, which was overestimated by 821 kg/month based on the empirical average particle mass. While tracking MP transport classified by shape and polymer type, the resuspension of MPs that accumulate in the intertidal zone cannot be neglected. The average relative error of the simulation was as low as 19.6% after including the abovementioned factors. Finally, the simulation results of the sensitive regions were extracted to assess the new MP risk index, which considers shape, abundance, and polymer type. By introducing these essential tools, this study helps to understand the fate of riverine MPs entering estuaries, where valuable opportunities for removing MPs exist before they spread to the oceans.

Microplastic Abundance in Rainbow Trout Life Cycle: Step by Step

In recent years, with the encouragement of national and international authorities, researchers on plastic levels in aquaculture have begun to assess consumer health risks as well as ecological monitoring. Based on this guidance, the aim of this study is to determine the microplastic load of rainbow trout raised under routine breeding conditions without an external treatment in all developmental stages from egg to +1 year of age. Sperm, egg, fertilized egg, eyed egg, alevin or such fry, and swimming fry on growing stock (1-year-old) stages of cultured fish and commercial feeds were used for the following stages: 300–500 µm, 500–800 µm, 800–1200 µm, 1 mm, 2 mm, 3 mm, 4 mm, and 5 mm. The samples were collected to determine the presence of microplastic (MP) and at which stage of this life cycle the MP has entered into the system intensively. The obtained findings showed that the total amount of MP determined in the stages without feed intake was 14 pieces, and this value increased by 557% (total of 92-piece MP) in fish that started external feeding. While no significant difference was found between the MP amounts in different feed groups, the dominant microplastic color in the feed groups was black and blue, and the polymer type was polyethylene. This general modelling, in which MP concentrations are determined in all life cycles from egg to adult in a cultured fish species, including in the given feeds, will encourage further research. Current findings have shown that any outsourced input used during growing periods can cause MP contamination to the end of fish production, processing, and storage.

How microplastic loads relate to natural conditions and anthropogenic activities in the Yangtze river basin

As the third largest river in the world, microplastic pollution in the Yangtze River basin is currently attracting worldwide attention. However, fragmented research information is insufficient to reveal the occurrence and driving mechanisms of microplastics throughout the Yangtze River basin. Building on a systematic review of 20 existing publications, this study constructed a dataset including microplastic data from 366 samples in the Yangtze River basin through a data filtering process, and data on natural conditions and anthropogenic activities from 101 basin municipalities. Further, multivariate statistical analysis was utilized to enhance the understanding of the abundance, composition and drivers of microplastics within the basin. Differences in microplastic abundance among the sampling sites were up to 5 orders of magnitude, with the highest abundance value found in the upstream city of Chengdu. The comprehensive diversity index used to describe the composition characteristics of microplastics ranged from 0.31 to 0.68, slightly higher than the national average. Based on a statistical analysis framework, natural conditions and anthropogenic activities were shown to jointly drive the distribution of microplastics, and the dominant driver shifted between the two with spatial variation. In the upstream, anthropogenic activities dominated by GDP (r = 0.85, P < 0.01) were the main positive factor. In the middle and downstream, natural conditions and anthropogenic activities had comparable driving forces as the stability of natural resistance increased, and both were positively correlated with microplastics. Combining the constructed normalized stepwise linear regression model with GIS spatial analysis, the basin-wide application demonstrated that microplastic pollution in the upstream and delta deserved more attention. After coupling the distance factors, microplastic pollution was concentrated in the middle and downstream of the Yangtze River basin, covering important drinking water sources. This study provided important data support for subsequent targeted microplastic reduction and treatment.

A nationwide assessment of microplastic abundance in agricultural soils: The influence of plastic crop covers within the United Kingdom

Societal Impact StatementAgricultural soils are substantial receptors of plastic pollution. Plastic crop covers, a facet of agriplastics, may represent an important contribution to microplastic load in agricultural soils. The authors present a nationwide study of agricultural soils in the United Kingdom, comparing microplastic load between sites where plastic crop covers are and are not used for carrot and potato production. Sites where plastic crop covers were used received a higher microplastic load compared with sites where no plastic crop cover was used. The effects of microplastic pollution are largely unknown, requiring further research to determine the impact on soil, crop and human health.Summary Agricultural soils are substantial receptors of plastic pollution, with agriplastics potentially making an important contribution to the overall microplastic load to agricultural soils. The intensive use and mismanagement of plastic crop covers, particularly plastic mulch films, nets and fleeces, represent a pollution pathway. In this study, we have analysed the microplastic concentrations in agricultural soils in 324 samples from 108 sites across the United Kingdom, where carrots or potatoes were grown, using a combined digestion and density separation method. Microplastics were stained with Nile Red and quantified using fluorescence microscopy. Microplastic concentrations ranged from 1320 to 8190 particles kg−1, with a mean of 3680 ± 129.1 particles kg−1. Where no plastic crop covers were used for potato and carrot production, a mean of 2667 ± 84.1 particles kg−1 were detected. At sites where plastic crop covers were used in the past 10 years, a mean of 4689 ± 147.1 particles kg−1 were recorded. There was a significant difference in microplastic abundance between sites where plastic crop covers were and were not used (p ≤ 0.001), confirming that plastic crop covers are an important source of microplastics to agricultural soils. Further studies are needed to investigate microplastic occurrence in the environment to better understand their impact on soil, crops and human health.

Patterns and variability in the microplastic contamination along the southwest coast of India with emphasis on submarine groundwater discharge sites

Beach sediments of the southwest coast of India were analysed to estimate the microplastic contamination with emphasis on the submarine groundwater discharge (SGD) zones. Both SGD and non-SGD sites were assessed for abundance, morphotype and polymer type of microplastics. Microplastic load was 230.429 ± 62.87 particles per 100 g. Fibre, mainly blue, was the abundant morphotype, followed by fragment, foam and film. The polymer types were POLYETHYLENE (PE) (30.77 %), POLYPROPYLENE (PP) (26.92 %), POLYAMIDE (PA) (19.23 %), POLYSTYRENE (PS) (11.54 %), ETHYLENE VINYL ACETATE (EVA) (7.692 %) and POLYVINYL CHLORIDE (PVC) (3.846 %). The SGD zones exhibited higher microplastic contamination with statistically significant variations from non SGD sites. The study accounts the levels of microplastic contamination along the southwest coast of India, a major fishery zone. The higher abundance of microplastic in the SGD zones indicates the significance of subterranean groundwater through flow as a pathway of anthropogenic contaminants towards marine ecosystems.

Sludge drying and dewatering processes influence the abundance and characteristics of microplastics in wastewater treatment plants

Wastewater treatment plants (WWTPs) have been identified as high-load receptors of microplastics (MPs) from different sources. However, the influence of specific treatment stanges requires further research. The main objective of this research was to evaluate the abundance and chemical characteristics of MPs in the sludge of two major wastewater treatment plants in the Agadir metropolis (Central Atlantic of Morocco). The Aourir plant receives urban influents and the inputs of the M'zar facility were urban and industrial. Samples were collected from the sludge matrices after primary settling, clarifying, dewatering, and drying systems. In addition, the effect of seasonality on MP load was assessed. The results showed that a higher abundance was noticed in raw sludge than in dewatered one in Aourir WWTP, while in M'zar WWTP, a very low decrease is noticed in dried sludge compared to raw sludge. The concentration of MPs in the summer season was significantly higher compared to other seasons for Aourir WWTP, while the winter season was higher for M'zar WWTP. Moreover, the most abundant shapes were fibers and the fraction 100–500 μm was the most preponderant. Eleven polymers were identified by ATR-FTIR, being polyester, polyethylene, polypropylene, and polystyrene the most abundant ones. Scanning Electron Microscopy coupled with Energy Dispersive X-ray revealed the visible degradation and fragmentation of MPs from sewage sludge and their ability to adsorb inorganic elements. It was estimated that between 2.2 × 107 and 7.4 × 108 MPs were evacuated with the sludge per day. The obtained findings confirmed that WWTP sludge acts as a vector of MPs with a high level of hazard to various matrices, such as landfills, agricultural soils, and groundwater. Overall, consideration must be given to the regulatory system managing the fate of sewage sludge to mitigate the collateral effects and provide solutions.

Wet Deposition of Globally Transportable Microplastics (

Microplastics of size <25 μm possess globally transportable features, but the impact of precipitation on their transport remains unclear. Here, microplastics were detected in all 10 studied rainfalls in Beijing, with <25 μm microplastics present in 8 rainfalls. Interestingly, microplastic abundance (7590-136,778 items·m-3) was tentatively linked to maximum rainfall intensity, with <25 μm microplastics making up 39.6 (±27.5)% of the total count. The composition of <25 μm microplastics differed from that of larger microplastics, although both mainly comprised polystyrene, polyethylene, and polypropylene. The microplastic communities differed among rainfalls, suggesting that atmospheric transport is a highly dynamic process. The first rainfall exhibited the highest microplastic abundance and community diversity after long-term exposure to dry atmospheric environment. The deposited microplastics were unstable and highly fragmented according to the conditional fragmentation model. The wet deposition rate of the microplastics was calculated as 2-463 μg·m-2 (146-8629 items·m-2) per rain, amounting to 25.44 tons per annum in Beijing. Although <25 μm microplastics represented a negligible proportion (0.00-1.24%) of the overall mass load of microplastics, their numerical abundance was high. Our results demonstrate that precipitation is an effective mechanism for removing airborne microplastics, which may enter urban soils and waters, exacerbate microplastic burdens in the environment, and cause potential risk for human health.

Arctic Ocean sediments as important current and future sinks for marine microplastics missing in the global microplastic budget

To better understand unexpectedly low plastic loads at the ocean’s surface compared with inputs, unidentified sinks must be located. Here, we present the microplastic (MP) budget for multi-compartments in the western Arctic Ocean (WAO) and demonstrate that Arctic sediments serve as important current and future sinks for MPs missing from the global budget. We identified an increase of 3% year −1 in MP deposition from sediment core observations. Relatively elevated MP abundances were found in seawater and surface sediments around the summer sea ice retreat region, implying enhanced MP accumulation and deposition facilitated by the ice barrier. We estimate 15.7 ± 2.30 × 10 16 N and 0.21 ± 0.14 MT as total MP loads in the WAO with 90% (by mass) buried in the post-1930 sediments, which exceeds the global average of the current marine MP load. The slower increase in plastic burial versus production implies a lag in plastic delivery to the Arctic, indicating more pollution in the future.

Removal efficiencies of microplastics of the three largest drinking water treatment plants in Bangladesh

Drinking water treatment plants (DWTPs) are intended to provide safe water to the municipality, typically by treating surface waters from rivers, lakes, and streams. Regrettably, all of these water sources for DWTPs have been reported to be contaminated by microplastics (MPs). Hence, there is an urgent need to investigate the removal efficiencies of MPs from raw waters in the conventional DWTPs anticipating public health concerns. In this experiment, MPs in the raw and treated waters of the three major DWTPs of Bangladesh, having different water treatment processes, were evaluated. The concentrations of MPs in the inlet points of Saidabad Water Treatment Plant phase-1 and 2 (SWTP-1 and SWTP-2), which share a similar water source of the Shitalakshya River, were 25.7 ± 9.8 and 26.01 ± 9.8 items L−1. The third plant, Padma Water Treatment Plant (PWTP) utilizes water from the Padma River and had an initial MP concentration of 6.2 ± 1.6 items L−1. The studied DWTPs, with their existing treatment processes, were found to reduce the MP loads substantially. The final MP concentrations in treated waters of SWTP-1, SWTP-2, and PWTP were 0.3 ± 0.03, 0.4 ± 0.01, and 0.05 ± 0.02 items L−1 with the removal efficiencies of 98.8, 98.5, and 99.2 %, respectively. The considered size range of MP was 20 μm to <5000. Fragments and fibers were the two predominant MP shapes. In terms of polymer, the MPs were polypropylene (PP, 48 %), polyethylene (PE, 35 %), polyethylene terephthalate (PET, 11 %), and polystyrene (PS, 6 %). The field emission scanning electron microscopy-energy dispersive X-ray spectroscopy (FESEM-EDX) revealed the fractured and rough surfaces of the remaining MPs, which were also found to be contaminated with heavy metals, like lead (Pb), cadmium (Cd), chromium (Cr), arsenic (As), copper (Cu), and zinc (Zn). Hence, additional initiatives are required to remove the residual MPs from the treated waters to safeguard the city dwellers from potential hazards.

Seasonal pulse effect of microplastics in the river catchment-From tributary catchment to mainstream

Rivers have received extensive attention as a major pathway for microplastics (<5000 μm) from land to ocean. This study investigated the seasonal variation of microplastic contamination in surface water of the Liangfeng River catchment, a tributary of the Li River in China, based on a fluorescence-based protocol, and further explored the migration process of microplastic in the river catchment. The abundance of microplastics (50–5000 μm) was (6.20 ± 0.57)–(41.93 ± 8.13) items/L, of which 57.89–95.12% were small-sized microplastics (<330 μm). The microplastic fluxes in the upper Liangfeng River, lower Liangfeng River, and upper Li River were (14.89 ± 1.24) × 1012, (5.71 ± 1.15) × 1012, and (1.54 ± 0.55) × 1014 items/year, respectively. The 3.70% of microplastic load in the mainstream came from the tributary input. Fluvial processes can effectively retain 61.68% of microplastics in the surface water of river catchments, especially for small-sized microplastics. The rainy season is the main period of microplastic retention (91.87%) in the tributary catchment by fluvial processes, while exporting 77.42% of one-year microplastic emissions from the tributary catchment into the mainstream. This study is the first to reveal the transport characteristics of small-sized microplastics in river catchments based on flux variation, which not only can partly explain the “missing small-sized microplastic fraction” in the ocean, but also contribute to improving microplastic model.

Low microplastic loads in riverine European eel (Anguilla anguilla) from southwest England during their marine-freshwater transition.

The microplastic loads in elvers of the critically endangered European eel Anguilla anguilla, sampled in the lower reaches of three English rivers, were very low (incidence: 3.3%, mean ± s.d.: 0.03 ± 0.18 particles) and did not vary with body length or between rivers. Particles were mostly black, polyolefins, fibres and fragments of size 101-200 μm. Current levels indicate a low contamination pressure locally and, consequently, management efforts might prioritise mitigating the effects of other stressors affecting the species.

Microplastic contamination in salted and sun dried fish and implications for food security – A study on the effect of location, style and constituents of dried fish on microplastics load

The presence of microplastics in 21 different species of marine dried fish products from four locations in India is reported in this study. All samples have microplastics, and majority of the MPs were found to be fragments (56 %) and are of <100 μm size (47 %). Eviscerated fish found to have significantly higher MPs than whole fish. Micro FTIR spectroscopy was used to recognize the polymer of identified MPs, which included polypropylene (21 %), low density polyethylene (17.5 %), polystyrene (15.5 %), and others. Anguilla bengalensis from station 1 had the greatest concentration of microplastics (99 ± 18.91 MPs/g) among all the samples. High value of microplastics polymer induced risk index (H) of different stations, suggesting a significant level of threat to consumer safety. Additional research is required to determine the potential effects on human health caused by consuming dried fish that contains variety of microplastics and their associated compounds.

Estimating Microplastics related to Laundry Wash and Personal Care Products released to Wastewater in Major Estonian Cities: a comparison of calculated and measured microplastics.

Microplastics (MPs) research still at the budding stage in Estonia. A theoretical model build on substance flow analysis principles was developed. The goal of this study is to broaden understanding of MPs-types in wastewater and their contribution from known sources, quantify their presence based on model prediction and in-situ measurements. The authors estimate MPs from laundry wash (LW) and personal care products (PCPs)) in wastewater in Estonia. We found out that total estimated MPs load per capita from PCPs and LW in Estonia were between 4.25 - 12 tons/year, 3.52 - 11.24 tons / year respectively, and estimated load ended up in wastewater were between 700 - 30,000kg/yr. and 2 - 1500kg/yr. in WWTPs influent and effluent stream respectively.Finally. We conducted a comparison between estimated MPs load and on-site sample analysis and observed a medium-high level of MPs being discharged into the environment annually. During quantification and chemical characterization using µFTIR analysis, we found that microfibers with a length of 0.2-0.6 mm accounted for over 75% of the total MPs load in the effluent samples collected from four coastal WWTPs in Estonia. The estimation avails us broader overview about the theoretical MPs load in wastewater and gain valuable insight into developing process methods that prevent MPs accumulation in sewage sludge for safe application in agriculture.

Microplastics discharged from urban drainage system: Prominent contribution of sewer overflow pollution

Urban drainage system is an important channel for terrigenous microplastics (<5 mm in size) to migrate to urban water bodies, especially the input load caused by overflow pollution in wet weather. Investigating how they transport and discharge is essential to better understand the occurrence and variability of microplastics in different water ecosystems. This study evaluated the abundance and distribution characteristics of microplastics in the drainage systems of typical coastal cities in China. The impacts of meteorological conditions and land use were explored. In particular, the prominent contribution of drainage sewer overflow pollution during storm events were investigated. The results showed that the microplastics abundance in daily sewage discharge from different drainage plots ranged between 13.6 and 30.8 items/L, with fibers as the dominant type of microplastics. Sewer overflow discharge can greatly aggravate microplastic abundance to 83.1 ± 40.2 items/L. Road runoff and sewer sediment scouring were the main pollution sources. Systematic estimates based on detailed data showed that the average microplastics emitted per capita per day in household wastewater was 3461.5 items. A quantitative estimation method was proposed to show that the annual emissions load of microplastics via urban drainage system in this research area was 5.83×1010 items/km2, of which the proportion of emissions in wet weather accounted for about 60%. This research provides the first full-process of assessment and source apportionment of the microplastic distribution characteristics in old drainage system. The occurrence of storm events is an important marker of increased microplastic abundance in urban rivers, with a view to urgent need for interception of surface runoff and purification of sewer overflow pollution.

Water or sediment? Assessing seasonal microplastic accumulation from wastewater treatment works

AbstractMicroplastics have become a major environmental concern around the world due to their potential impact on ecosystem functioning and biota. Microplastics enter freshwater systems through a variety of sources, with wastewater treatment work discharges being the most important source. The study aimed to determine the seasonal (i.e., hot–wet, cool–dry) variation in water and sediment microplastic abundances up- and down-stream of wastewater treatment works across two subtropical river systems (i.e., Crocodile and Luvuvhu) in South Africa. Overall, we found that microplastic type and distribution often did not show clear seasonal and site differences in water, hence microplastics were widespread across the studied systems and microplastic concentrations did not relate clearly to wastewater treatment works. This was further indicated by microplastic risk assessments which showed high pollution loads upstream. However, there were significant differences in sediment microplastic loads across seasons, indicating a source-sink effect towards the hot-wet season. The non-metric multidimensional scaling ordination based on microplastic densities for water and sediment discriminated slightly among systems, with major overlaps across the different locations and seasons. As a result, the current research indicates that seasonal context influences differences in microplastic concentrations, with the hot–wet season being associated with the high pollution loads, particularly within the sediments where this was more pronounced indicating the sink-source effect which is linked to sediments and not water.

Direct numerical simulation of the distribution of floating microplastic particles in an open channel flow

AbstractMicroplastic fragments in the aquatic environment constitute a major threat for the health and fitness of organisms. However, our quantitative understanding in the microplastic load in typical natural river systems is severely limited due to the large uncertainties associated with the sources and the pathways of the microplastic contamination. To address this knowledge gap, we performed direct numerical simulations of the dynamics and distribution of microplastic particles in turbulent open channel flow at moderate Reynolds numbers. The particle dynamics is characterised by four nondimensional parameters, namely: Reynolds number of the open channel flow (), nondimensional particle diameter () and Galileo () and Stokes () numbers of the particles of which the latter two include the particle‐fluid density ratio (). To limit our scope to the most relevant configuration, we focused on the distribution of weakly buoyant microplastic particles at , whereas the remaining parameters were adjusted to cover the orders of magnitude that can be found in a typical laboratory facility, as well as a natural river. Our simulation results show that the steady‐state microplastic distribution in the turbulent flow is influenced by the Stokes and the Galileo numbers significantly, which ranges from the complete accumulation on the free surface to the homogeneous distribution, and somewhere in between. Moreover, the Galileo number, alongside the flow Reynolds number, were also shown to influence the temporal scaling of the transient behaviour of the gradual accumulation of the microplastics towards the free surface. Both of our findings highlight the complex nature of the particle–turbulence interactions, and motivate further investigations in this approach.

Prevalence of microplastics in commercially sold soft drinks and human risk assessment

Due to the increasing global plastic production and use in recent years, the amount of microplastic (MP) accumulating in the environment has also increased. This microplastic pollution potential has been documented mostly in studies of the sea or seafood. The presence of microplastics in terrestrial foods has therefore attracted less attention, despite the potential for future major environmental risks. Some of these researches are related to bottled water, tap water, honey, table salt, milk, and soft drinks. However, the presence of microplastics in soft drinks has not yet been evaluated in the European continent, including Türkiye. Hence, the current study focused on the presence and distribution of microplastics in ten soft drink brands in Türkiye since the water utilized in the bottling process of soft drinks originates from different water supply sources. Using FTIR stereoscopy and stereomicroscope examination, MPs were detected in all of these brands. According to the microplastic contamination factor (MPCF) classification, 80% of the soft drink samples indicated a high level of contamination with microplastics. The study's findings showed that each liter of consumed soft drinks exposes people to about nine microplastic particles, which is a moderate dose when compared to exposure levels in earlier research. It has been determined that bottle-production processes and the substrates used for food production may be the main sources of these microplastics. The chemical components of these microplastic polymers were polyamide (PA), polyethylene terephthalate (PET) and polyethylene (PE), and fibers were the dominant shape. Compared to adults, children were subjected to higher microplastic loads. The study's preliminary data on MP contamination of soft drinks may be useful for further evaluating the risks exposure to microplastics poses to human health.

Microplastic occurrence and ecological risk assessment in the eight outlets of the Pearl River Estuary, a new insight into the riverine microplastic input to the northern South China Sea

Estuaries are unique transition zones connecting terrestrial and coastal environments and are recognized as primary conveyors for land-derived plastics to open oceans. Riverine microplastics (MPs) have been commonly investigated using sequential sampling which might not effectively reflect the actual load. In this study, sampling at eight outlets was performed during a complete tidal cycle to estimate the MP flux to the Pearl River Estuarine (PRE) using a concurrent sampling strategy. The MP abundances ranged from 2.90 ± 0.57–5.9 ± 2.27 particles/L. A remarkable difference between tides in MP abundances suggests tidal effect should not be overlooked in assessment. The MP load through the eight outlets was estimated at 304 trillion particles or 1102 tons into the PRE annually. Additionally, similar potential ecological risk assessment among eight rivers implied that environmental threats posed by less urbanized and populated rural areas on the western side have been under-evaluating for decades.

Microplastics: The stemming environmental challenge and the quest for the missing mitigation strategies

Repetitious manufacturing, usage and irresponsible disposal trigger the breakdown of primary and secondary plastics, ending up in aquatic, terrestrial, and pristine locations like arctic tundra due to their diaphanous property. Owing to their origin, size, interaction with other contaminants, and chemical behavior they can be very idiosyncratic; they not only accumulate in the ecosystem, imparting chemical alterations but also are being consumed by the aquatic and terrestrial animals leading to hazardous consequences. Washing machine wastewater significantly contribute to the global microplastic load. For the past few years, microplastics (MP) and microfibers (MF) have been contaminants of grave concern pertaining to their deleterious nature against human, marine, and ecosystem health and grabbed the attention of environmental researchers. This review sums up the inimical ramifications of these tiny particles on biota, their types and characterization strategies, along with the biological removal strategies of these plastics and fibers highlighting the circular economy approach to limit them in the source and the enzymatic pathways regulating their eradication. Additionally, there are several research gaps in the biological remediation of these particles, which can be explored further to develop distinct, lucrative and ecologically reliable technologies for combating this mammoth (ironically) environmental adulterants.