Microshear Bond Strength Research Articles

Different surface treatments on recently introduced CAD-CAM resin-modified ceramics: Implications on bond strength

Statement of problemThe diverse chemical composition of recently introduced resin-modified ceramics complicates the establishment of a universally accepted clinical bonding protocol. PurposeThe purpose of this in vitro study was to evaluate the influence of different surface treatments of resin-modified ceramics on the bond strength to a resin cement. Material and methodsSixteen 10×12×3-mm resin-modified ceramic slices were obtained from each material (Cerasmart; GC, Shofu Block HC; Shofu, Vita Enamic; Vita, Evolux hybrid; BlueDent, Alium; Alium). Slices were assigned to 4 groups based on surface treatments: Control (no treatment), airborne-particle abrasion with Al2O3 (Al2O3), conditioning with 9% HF (HF), and Al2O3+HF. After treatments and silane coupling agent (Monobond N; Ivoclar) application, 7 resin cement cylinders (Choice 2 veneer; Bisco) were built on each slice and light polymerized for 20 seconds. Half of the specimens (n=14 cylinders) were stored for 24 hours, and the other half were thermocycled (20 000 cycles, 5 °C to 55 °C, 30-second dwell time). Microshear bond strength was tested and analyzed with 3-way ANOVA and the Tukey HSD test (α=.05), and failure patterns were classified. Surface morphology after treatments was observed with scanning electron microscopy and Raman spectroscopy. ResultsAfter 24 hours, all treatments induced higher bond strength (P<.05) than in the control in Evolux. Al2O3+HF caused higher bond strength (P<.05) than in the control in Cerasmart and Shofu, and higher bond strength than Al2O3 in Cerasmart. However, it resulted in lower bond strength (P<.05) than Al2O3 in Alium. After thermocycling, irrespective of the resin-modified ceramic, all treatments induced higher bond strength (P<.05) than in the control. HF induced lower bond strength (P<.05) than Al2O3 in Alium. Al2O3+HF caused the highest bond strength (P<.05) in Evolux and higher bond strength (P<.05) than HF in Vita Enamic. Adhesive failures were prevalent under control conditions, and mixed failures were common after treatments. Al2O3 induced surface alterations in all resin-modified ceramics. HF notably altered Vita Enamic, while it had no noticeable impact on the other resin-modified ceramics. Al2O3+HF caused a considerable alteration in Vita Enamic and modified the other resin-modified ceramics. Vita Enamic had the characteristic vibrational bands of inorganic compounds, while the other resin-modified ceramics exhibited distinct bands associated with organic compounds. ConclusionsAirborne-particle abrasion with Al2O3 followed by HF yielded the highest bond strength, regardless of the resin-modified ceramic, except for Alium, which demonstrated better bond strength after airborne-particle abrasion with Al2O3. 9% HF for 30 seconds caused notable surface alterations in Vita Enamic, negatively impacting its bond strength. Vita Enamic was the only resin-modified ceramic displaying both organic and inorganic composition, while the other resin-modified ceramics showed predominantly organic composition.

Effect of Blood Decontamination Procedures on the Microshear Bond Strength of Resin-modified Glass Ionomer Cement to Resin Composite.

To investigate the effect of decontamination procedures on the microshear bond strength (μSBS) of blood-contaminated resin-modified glass ionomer cement (RMGIC) bonded to resin composite (RC). Eighty RMGIC disc specimens were allocated into 5 groups (n=16). All groups except Group 2 were contaminated with blood. Group 1 had no decontamination procedure, Group 3 was decontaminated by rinsing, Group 4 was decontaminated by 34% phosphoric acid etching, and Group 5 was decontaminated by 5% sodium hypochlorite application. RMGIC specimens were subsequently bonded with RC using a universal adhesive in self-etch mode. μSBS tests were conducted using a universal testing machine at a crosshead speed of 1 mm/min. Failure mode analysis was conducted on RMGIC fracture surfaces under a scanning electron microscope. μSBS results indicated that Group 4 had the highest mean μSBS value of 6.22 ± 2.14 MPa, while Group 1 had the lowest mean μSBS value of 3.53 ±1.67 MPa. Significant differences were observed in the μSBS of Group 2 with no contamination (p=0.023) and Group 4 with decontamination by phosphoric acid-etching (p=0.003) when compared to Group 1 with blood contamination. No statistically significant differences (p>0.05) were observed between all other groups' μSBS. For all groups, the predominant mode of failure was adhesive failure between the RMGIC-RC interface, with a few mixed failures in RMGIC for Groups 2-5. Blood contamination before adhesive application significantly reduced the μSBS between RMGIC and RC. Phosphoric acid etching was the most effective blood decontamination procedure to improve the μSBS.

A comparative evaluation of the effect of eugenol exposure time on the bond strength of an etch-and-rinse and a self-etch adhesive to dentin: An in vitro study.

The study aimed to comparatively evaluate the effect of eugenol exposure time on the micro-shear bond strength (μ-SBS) of etch-and-rinse and a self-etch adhesive to dentin. One hundred and twelve teeth samples were prepared from bisectioning 56 freshly extracted human mandibular molars and were randomly divided into 14 subgroups of 8 samples each (n = 8). Three subgroups containing eugenol and a noneugenol-based restorative material were placed on the dentin surface and left for 24 h, 7 days, and 14 days, respectively, and were compared to a control. Two bonding systems were evaluated: one being etch-and-rinse and the other self-etch adhesive. The μ-SBS were calculated and expressed in MPa. The data were analyzed using mixed model analysis of variance. The level of statistical significance was set at 5%. There was a statistically significant reduction in the μ-SBS values when the self-etch adhesive was used, after the removal of eugenol-containing cement placed for 24 h. However, the reduction in the μ-SBS values after 7 days or 14 days was not significant. Exposure to eugenol containing temporary cement for 24 h significantly reduces the μ-SBS of self-etching adhesives to dentin. However, exposure for 1 week or more has minimal effects.

Effect of storage time on chemical structure of a single-bottle and a two-bottle experimental ceramic primer and micro-shear bond strength of composite to ceramic.

This study assessed the effect of storage time on chemical structure of a single-bottle and a two-bottle experimental ceramic primer and micro-shear bond strength (µSBS) of composite to ceramic. This study was conducted on 60 sintered zirconia and 60 feldspathic porcelain blocks. Half of the specimens (n = 30) were subjected to surface treatment with the single-bottle Clearfil ceramic primer (n = 15) and two-bottle experimental primer (n = 15) after 24 hours. The remaining half received the same surface treatments after 6 months storage in distilled water. Composite cylinders were bonded to the ceramics, and they were then subjected to µSBS test. Also, the primers underwent Fourier-transform infrared spectroscopy (FTIR) after 24 hours and 6 months to assess their chemical structure. Data were analyzed with 3-way ANOVA and adjusted Bonferroni test (alpha = 0.05). The µSBS of both ceramics significantly decreased at 6 months in one-bottle ceramic primer group (P = .001), but it was not significantly different from the two-bottle experimental primer group (P = .635). FTIR showed hydrolysis of single-bottle primer, cleavage of silane and 10-MDP bonds, and formation of siloxane bonds after 6 months. Six months of storage caused significant degradation of single-bottle ceramic primer, and consequently had an adverse effect on µSBS.

Influence of Varied Silane Commercial Brands and Adhesive Application on Bond Strength and Stability to Lithium Disilicate Glass Ceramic.

This study aimed to evaluate the impact of various commercial silane brands with varied chemical compositions with or without the application of an adhesive layer on the microshear bond strength and durability of a resin luting agent to lithium disilicate glass ceramic. Lithium disilicate glass ceramic discs (EMX, IPS e.max Press, Ivoclar Vivadent) measuring 10 mm in diameter and 3 mm in thickness were fabricated (n=240). Surfaces were etched using 5% hydrofluoric acid and randomly assigned to 10 groups based on the commercial brand of silane used (n=24): [RP] RelyX Ceramic Primer (3M ESPE); [PS] Prosil (FGM); [SA] Silano (Angelus); [SM] Silano (Maquira); [SU] Silane (Ultradent); [GL] GLUMA Ceramic Primer (Kulzer); [CB] Ceramic Bond (VOCO); [MB] Monobond N (Ivoclar Vivadent); [CP] Clearfil Ceramic Primer (Kuraray); and [DE] 2-step silane (Dentsply Sirona). Half of the EMXs (n=12) received a thin adhesive layer (+) after the silane and prior to resin luting agent, while the other half (n=12) did not receive an adhesive layer (-). For the microshear bond strength test (μSBS), four light-cured resin luting agent cylinders (1 mm in diameter) were created on each EMX surface. Half of these specimens were tested after 24 hours, while the other half were stored in deionized water for 6 months. The μSBS test was conducted using a universal testing machine (DL 500, EMIC) at a crosshead speed of 1 mm/min until failure. The obtained data underwent statistical analysis using analysis of variance (ANOVA) and the Tukey test (α=0.05). There was significant influence of the silane commercial brand on bond strength. Notably, "universal primers" yielded lower bond strength results compared to "pure" silane solutions. Water storage had a detrimental effect on microshear bond strength for certain silane commercial brands. Additionally, the application of an adhesive layer negatively impacted bond strength results for all silanes. This study confirms the importance of both silane commercial brand and chemical composition in relation to bond strength of resin luting agents to lithium disilicate glass ceramic. Furthermore, the application of an adhesive layer may have an adverse effect on bond stability over time.

Micro-shear Bond Strength of an Alternative Self-etch Application of "No Wait" Universal Adhesive to Caries-affected and Sound Dentin in Permanent and Primary Teeth.

This study aimed to compare the micro-shear bond strength (μSBS) of caries-affected dentin (CAD) and sound dentin (SoD) in primary and permanent teeth using an alternative self-etch application of "no wait" universal adhesive. Flat midcoronal dentin surfaces from 72 permanent third molars and 72 second primary molars were distributed randomly into 12 groups according to the substrate SoD and artificially-created CAD (pH cycling for 14 days) and the adhesive system (GLUMA Bond5, a two-step etch & rinse adhesive, GLUMA Bond, a one-step self-etch adhesive, and Tokuyama Universal Bond, a one-step self-etch adhesive) (n=12). Bonded dentin resin discs were put through micro-shear bond strength testing after 10,000 thermocycles. The results were evaluated using two-way ANOVA and the Bonferroni test with a significance level of α = 0.05. When compared to SoD, the etch & rinse system's test results on artificially created CAD showed a statistically significant poorer bonding performance in both permanent and primary teeth in all groups (p<0.05). While the bond strengths of permanent teeth using total-etch adhesive on sound dentin were statistically significantly higher than those using Tokuyama Universal Bond adhesive (p<0.05), there was no significant difference in sound dentin in primary teeth (p>0.05). The etch & rinse system performed the poorest of all adhesive systems on CAD. The Tokuyama Universal Bond's adhesive strength was similar in SoD and CAD on primary teeth. The use of Tokuyama Universal Adhesives can speed up restorative treatment in pediatric dentistry.

Micro-shear bond strength of a novel resin-modified glass ionomer luting cement (eRMGIC) functionalized with organophosphorus monomer to different dental substrates

ObjectivesThis study aims to assess and compare the micro-shear bond strength (μSBS) of a novel resin-modified glass-ionomer luting cement functionalized with a methacrylate co-monomer containing a phosphoric acid group, 30 wt% 2-(methacryloxy) ethyl phosphate (2-MEP), with different substrates (dentin, enamel, zirconia, and base metal alloy). This assessment is conducted in comparison with conventional resin-modified glass ionomer cement and self-adhesive resin cement. Materials and methodsIn this in vitro study, ninety-six specimens were prepared and categorized into four groups: enamel (A), dentin (B), zirconia (C), and base metal alloys (D). Enamel (E) and dentin (D) specimens were obtained from 30 human maxillary first premolars extracted during orthodontic treatment. For zirconia and metal alloys, 48 disks were manufactured using IPS e.max ZirCAD through dry milling and Co–Cr powder alloy by selective laser milling. Each group was further subdivided into three subgroups (n = 8) according to the luting cement used: (1) Fuji PLUS resin-modified glass ionomer luting cement (FP) as a control cement, (2) modified control cement (eRMGIC), and (3) RelyX U 200 (RU 200) self-adhesive resin cement. The two-way analysis of variance and Tukey's HSD were used to assess the data obtained from measuring the μSBS of the samples. ResultsThe results of this study showed that the mean μSBS values of eRMGIC were statistically higher compared to FP in all tested groups (p < 0.001). The mean μSBS results of eRMGIC were non-significantly different from those recorded by RU 200 for all substrates except for the dentin substrate, where the RU200 cement produced significantly higher strength (p < 0.001). The failure modes were limited to a combination of mixed and adhesive failures without pure cohesive failure. SignificanceThe functionalization of FP with an organophosphorus co-monomer (2-MEP) directly affects the adhesion performance of the functionalized cement, which may be utilized to develop a new type of acid-base cement. It exhibited a performance comparable to that of resin-based cement and should serve well under different clinical conditions.

Effect of Preventive Dental Products on Bonding Force: An in vitro Study.

Testing the effect of Fluoride, chlorhexidine, and molecular iodine applications on the mean micro-shear bond strength (SBS) of enamel in an attempt to preserve enamel integrity during the bonding process. The study was an observational case-control one in which 150 human teeth were classified into 10 groups according to the product kind and the prescribed treatment. Each group consisted of 15 teeth. Group C was the control group. Groups FP, FV, and OS utilized products that could be utilized in a professional dental setting. Group FP was treated with 1.23% NaF prophy paste, Group FV was treated with 5% NaF varnish, and Group OS was treated with Opal® Seal Fluoride releasing primer and sealant. Groups L, LF, CHX, and I were treated with mouth rinses. Group L was treated with Listerine Zero Fluoride-Free Mouthwash, Group LF with Listerine Zero 0.02% NaF Mouth Rinse, Group CHX with 0.12% chlorhexidine gluconate, and Group I with ioRinse RTU 100 ppm molecular iodine rinse. Groups TP and G utilized alternative remineralization products. Group TP was treated with Fluoro Calcium Phosphosilicate bioglass containing toothpaste, and Group G was treated with Curodont Protect remineralizing tooth gel. One-way ANOVA test was utilized to perform all statistical analysis in this study. For mean micro-SBS, no significant difference (P > 0.05) between any of the experimental groups was observed when compared to the control group. There was a significant difference (P < 0.05) between Opal Seal versus Listerine Total, Opal Seal versus Peridex, Listerine versus Listerine Total, and Listerine versus Peridex. All other experimental group comparisons revealed a nonsignificant difference (P > 0.05). As the null hypothesis (H0) assumes that changes observed in an experiment are due to chance, hence, the outcomes of this study are coherent with (H0) since the aforementioned application methods did not significantly impact the SBS of orthodontic resin cement to enamel.

Influence of Immediate Dentin Sealing on Bond Strength of Resin-Based CAD/CAM Restoratives to Dentin: A Systematic Review of In Vitro Studies.

Immediate dentin sealing (IDS) is a method of improving the bond strength of indirect dental restorative materials to dentin and belongs to the biomimetic protocols of contemporary dentistry. The purpose of this systematic review was to evaluate the effect of IDS on the bond strength of resin-based CAD/CAM materials to dentin. PubMed and MEDLINE, Scopus, and the Web of Science were searched by two individual researchers, namely for studies that have been published in English between 1 January 2005 and 31 December 2023 in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement. The inclusion criteria encompassed articles related to in vitro studies, measuring the bond strength through microtensile bond strength (μ-TBS), micro-shear bond strength (μ-SBS), tensile bond strength (TBS) or shear bond strength (SBS) tests after the use of the IDS technique. The included restorative materials comprised resin-based CAD/CAM materials bonded to dentin. A total of 1821 studies were identified, of which 7 met the inclusion criteria. A meta-analysis was not deemed appropriate due to the high level of diversity inthe publications and techniques. The use of IDS yielded higher bond strength outcomesin various experimental conditions and resin-based CAD/CAM materials. Overall, IDS in CAD/CAM restorations may contribute to better clinical outcomesand improved restoration longevity due to this property.

The impact of artificial aging using chewing simulator on micro-shear bond strength and micro-leakage of alkasite and bioactive resin based composites: an in-vitro comparative study

Objective The current study was conducted to assess and compare the impact of artificial aging using chewing simulator on the novel bulk fill restorative materials (Cention N) and Bioactive Resin Based Composites (ACTIVA) regarding, micro-shear bond strength and micro-leakage. Tetric N ceram bulk fill composite was used as control. Patients and methods For micro-shear bond strength testing, thirty recently extracted molars were collected, then their occlusal surfaces were cut horizontally using low-speed diamond saw under coolant exposing flat dentin surfaces. Tetric N-Bond adhesive was applied to the dentin surface, then Tygon tubes (three for each tooth) with height 1 mm and internal diameter 1 mm were placed on the flat surfaces, followed by light curing, then the restorative material (10 specimens for each material) was condensed inside the tubes. Half of the specimens is subjected to artificial aging (thermal and dynamic loading using Chewing Simulator). The specimens were mounted in blocks of stones, then placed horizontally in the universal testing machine. The load was applied using a knife-edge chisel till debonding of the composite cylinders from dentin surface. Fifteen extracted human molars were utilized for the purpose of evaluating micro-leakage. A total of thirty class II cavities were meticulously constructed on the mesial and distal surfaces of the teeth. The evaluation of micro-leakage was conducted using a dye penetration test, employing a scoring system ranging from 0 to 4. Results The nonaged specimens of the tested materials did not show significant differences regarding micro-shear bond strength, and micro-leakage. Aging had no significant effect on all of the tested properties in the three tested materials. Conclusion Short-term thermomechaical aging used in this study did not deteriorate micro-shear bond strength and micro-leakage of the tested materials. Alkasite (Cention N) and ACTIVA Bioactive Resin Based Composites are promising materials with physico-mechanical properties comparable to conventional bulk-fill composites. However, further in vitro and in vivo studies are needed to assess the properties of these recently introduced materials.

Effect of Surface Treatment with Alkaline Agents at Two Different Temperatures on Microshear Bond Strength of Zirconia to Composite Resin.

Zirconia, with its excellent mechanical properties, has become a popular choice for esthetic and durable restorations due to the increasing demand of patients. It has overcome most of the limitations of all ceramic restorations. However, bonding to zirconia remains a challenge. This study is aimed at assessing the effect of surface treatment with alkaline agents at two different temperatures on microshear bond strength (μSBS) of zirconia to composite resin. This in vitro, experimental study was conducted on zirconia blocks measuring 2 × 4 × 8 mm. The blocks were sandblasted with alumina powder and randomly assigned to 5 groups (n = 16 each). The blocks in groups 1 and 2 underwent surface treatment with sodium hydroxide (NaOH) and groups 3 and 4 with zirconium hydroxide (Zr(OH)4) at room temperature and 70°C. Group 5 served as the control group and did not receive any surface treatment. After the application of bonding agent and its light-curing, composite cylinders in plastic tubes were bonded to the surface of each block and cured. After incubation, they underwent μSBS test. Data were analyzed by one-way ANOVA and Tukey's test (alpha = 0.05). The μSBS was significantly higher in all intervention groups than that in the control group (P < 0.05). The μSBS in Zr(OH)4 groups was significantly higher than that in NaOH groups (P < 0.05). The mean μSBS of heated groups was slightly, but not significantly, higher than the corresponding room temperature groups (P > 0.05). Surface treatment of zirconia with NaOH and Zr(OH)4 alkaline agents can increase its μSBS to composite resin; Zr(OH)4 was significantly more effective than NAOH for this purpose, but heating did not have a significant effect on μSBS.

Evaluation of the microshear bond strength of resin cement to zirconia treated by different nanomaterials using the dip coating technique

Evaluation of the microshear bond strength of resin cement to zirconia treated by different nanomaterials using the dip coating technique

Can a Self-etching Primer be Effective in Bonding Aligner Attachments to Different Types of Ceramics?

This in vitro study aimed to evaluate the effectiveness of pretreatment with a self-etching primer for bonding aligner attachments to lithium disilicate (LD) and monolithic zirconia (MZ) ceramics. Forty ceramics, including LD (n=20) and MZ (n=20), were divided into four study groups according to the surface pretreatments: LD specimens pretreated with universal primer (Monobond Plus, MP) after hydrofluoric acid etching (Group 1); MZ ceramics pretreated with MP after sandblasting (Group 2); LD ceramics pretreated with self-etching ceramic primer (Monobond etch & prime, MEP) (Group 3); and MZ ceramics pretreated with MEP after sandblasting (Group 4). The aligner composite (GC Aligner Connect) and universal adhesive (GPremio Bond) were used to prepare the resin attachments. The bond strength was evaluated by micro-shear bond strength (SBS) testing (0.1 mm/min) after thermocycling, and the remnant adhesive was scored according to the resin attachment remnant index (RARI). The SBS data were analyzed using ANOVA and Tukey tests, and the RARI scores were analyzed using the chi-square test. Group 1 had the lowest SBS, and group 2 had the highest SBS. There were significant differences between the groups in terms of bond strength (p<0.05). The RARI scores showed no significant differences, regardless of the pretreatment and ceramic type. The use of a self-etching primer increased the bond strength of resin attachments on LD ceramics. For zirconia ceramics, both ceramic primers are recommended for aligner attachment bonding.

Adhesion of glass ionomer cements to primary dentin using a universal adhesive.

Glass ionomers are widely used for restoring carious primary teeth. However, their ability to bond to primary dentin is considered a challenge in pediatric dentistry. The study aimed to evaluate the microshear bond strength (μSBS) of a resin-modified glass ionomer (RMGI) and a high-viscosity glass ionomer cement (Hv-GIC) to primary dentin using a universal adhesive. Thirty human primary maxillary canines were cut in half and prepared for the μSBS test. The specimens (N = 60) were assigned to 6 groups. Three groups were defined for RMGI (FUJI II LC) and 3 groups for Hv-GIC (EQUIA Forte): with an immediately curing adhesive (G-Premio); with a delayed curing adhesive; and without an adhesive (control group). After preparing the dentin surfaces, the glass ionomers were bonded using Tygon® tubes with an internal diameter of 0.7 mm. The μSBS test was performed, and the data was analyzed using two-way analysis of variance (ANOVA) followed by Tukey's post hoc test. Additionally, the failure modes were determined using a stereomicroscope. Six specimens, one for each study group, were prepared for scanning electron microscopy (SEM) analysis to observe the glass ionomer-dentin interface. The type of glass ionomer did not have a significant effect on the μSBS (p = 0.305). Groups that received universal adhesive application prior to glass ionomer exhibited a significantly higher μSBS (p < 0.0001). However, there was no significant difference between the immediately curing and delayed curing groups (p = 0.157). The predominant failure mode was mixed failure. Higher bond strength of glass ionomers to primary teeth can be achieved by using universal adhesives, which, in addition to the proven benefits of glass ionomers, can improve their clinical success.

The Effect of Bioglass Coating on Microshear Bond Strength of Resin Cement to Zirconia.

Objectives: Durable bonding to zirconia is a challenging issue in dentistry. This study aimed to assess the effect of bioglass coating of zirconia on the microshear bond strength of resin cement to zirconia and to study the effect of thermocycling on this bond. Materials and Methods: This in-vitro experimental study was conducted on 60 yttria-stabilized tetragonal zirconia blocks in six groups (N=10) based on surface pretreatment and thermocycling. Surface pretreatments included no treatment control, alumina particle abrasion, and bioglass-coating of zirconia. Resin bonding was performed with Panavia F2.0 cements. Then, half of the specimens underwent a 24-hour incubation in 37°C water, while the other half were subjected to thermocycling (12000 cycles, 5-55°C, 60s for each batch) following the same incubation period. Subsequently, the microshear bond strength of the specimens was measured. Additionally, one block from each group was subjected to scanning electron microscopy and X-ray diffraction. The data were analyzed using Kruskal-Wallis and Mann-Whitney U tests. Results: There was a significant difference between the bond strength values of different groups (P<0.001). Alumina particle abrasion and bioglass coating equally increased the bond strength compared to the untreated control group (P<0.001). Thermocycling caused significant decreases in bond strength in all the groups (P<0.001); however, the bond strength value of the thermocycled bioglass-coated group was significantly higher than that reported for the thermocycled alumina particle abraded group (P=0.015). Conclusion: Despite the decrease in the bond strength values after thermocycling, the long-term efficacy of the bioglass coating of zirconia was promising.

Delayed vs. immediate placement of restorative materials over Biodentine and RetroMTA: a micro-shear bond strength study

BackgroundThe aim of the present study was to investigate the micro-shear bond strength (µSBS) of various restorative materials applied on two different fast-setting calcium silicate-based materials and to evaluate the effect of restoration time on µSBS.MethodsA total of 180 acrylic blocks with a cavity in the center were randomly divided into 2 main groups according to the capping material to be used (Biodentine or RetroMTA). The specimens were also randomly divided into 3 groups according to the restoration time (3 min, 12 min, 24 h). After the specified waiting periods, glass hybrid material (EQUIA Forte HT), resin composite (Filtek Z550) and light-cured calcium silicate material (Theracal LC) were placed on the specimens with tygon tubes. The specimens were kept for 24 h and then subjected to µSBS test. Statistical analysis was performed by 3-way ANOVA followed by Tukey test for pairwise comparisons (α = 0.05).ResultsThere is a statistically significant difference (p < 0.05) between the µSBS values obtained by applying resin composite on RetroMTA after different setting times (24 h > 12 min > 3 min). The µSBS obtained for the Biodentine-resin composite at the end of the 3 min setting time is significantly lower (p < 0.05) than the µSBS values at 12 min and 24 h. For both calcium silicate cements, at the end of all time periods, the µSBS obtained when resin composite was applied at the end was higher than the other materials (p < 0.05).ConclusionsFor Biodentine-resin composite bonding, the manufacturer’s recommendation of 12 min can be considered an appropriate time, whereas for RetroMTA-resin composite bonding, the µSBS increased as the waiting time increased. Regardless of the waiting time, it is recommended to prefer direct composite resin restoration over Biodentine and RetroMTA.

Influence of Application Modes on Increasing Bond Strength Longevity of Self-etching and Universal Adhesive Systems to Enamel.

The present study aimed to evaluate the influence of application mode on the short-term microshear bond strength longevity of self-etching and universal adhesive systems to enamel, the failure mode, and the resulting enamel surface micromorphology. Ninety enamel surfaces were obtained from sound third molars, planed, and randomly assigned to nine groups, according to the application mode and the adhesive system (n=10). There were three primer application modes: according to the manufacturer's recommended application time (control), using double the application time recommended for the primer and selective enamel etching. The adhesive systems used were: Clearfil SE Bond (Kuraray), FL-Bond II (SHOFU), and Futurabond U (Voco). At least two resin-bonded composite cylinders (Grandioso Light Flow, Voco) were placed on each enamel surface, and then evaluated for microshear bond strength at 24 hours and 180 days of storage in solution body fluid (SBF) at pH 7.4. Failure modes were evaluated with a stereoscopic microscope at 20× magnification. A micromorphological analysis of the enamel surface was performed under a scanning electron microscope at 5000× magnification before and after the treatments. Mixed models for repeated measures over time showed significant interaction among application modes, adhesive systems, and time periods (p=0.0331). The bond strength of FL-Bond II adhesive to enamel observed after performing selective enamel etching was significantly higher than that observed after applying the control treatment (p=0.0010) at both 24 hours and 180 days. However, no significant difference was observed between the application of this same adhesive at double the time recommended by the manufacturer and the other two application modes (p>0.05). There was also no significant difference in the microshear bond strength for the enamel treatments applied using Clearfil SE Bond and Futurabond U (p>0.05). A significant reduction in bond strength to enamel was observed at the 180-day storage time for all the adhesive systems when selective enamel etching was performed (p<0.0001). No significant association was observed between the adhesive system failure mode and the enamel treatments (p=0.1402 and p=0.7590 for 24 hours and 180 days, respectively). The most prevalent failure was the adhesive type.

Effect of hydrofluoric acid concentration and aging on the bond strength ceramics to a resin cement.

This study evaluated the influence of hydrofluoric acid (HF) concentration and thermal cycling on the microshear bond strength (µSBS) of a resin luting agent to IPS e.max® CAD and Rosetta® SM. Ceramic specimens (12.0 x 14.0 x 1.5mm) were randomized into 8 groups (n=10) according to HF concentration, commercial brand, and aging. Immediately after polishing, and etching, all specimens were silanized and a layer of adhesive was applied. A PVS mold of 3 mm thickness and 10mm diameter with (four) 1.0mm holes was fabricated, placed on each specimen, and then filled with a resin luting agent. Half of the specimens were subjected to the µSBS test using an Instron at a speed of 1.0 mm/min, following a 24-hour storage in deionized water at 37ºC. The remaining specimens were subjected to thermal cycling (5ºC-55ºC, 30 seconds per bath) and µSBS. The data were evaluated utilizing a three-way ANOVA and Tukey's post-hoc test (α=0.05). Significant differences were found for HF concentration and aging (p<0.0001). No significant difference in µSBS was found for commercial brands (p=0.085). The interaction between brand and HF concentration (p=0.358), brand and aging (p=0.135), and HF concentration and aging (p=0.138) were not statistically significant. The triple interaction among these factors was not statistically significant (p=0.610). In conclusion, the bond strength is affected by the HF concentration. No statistical difference was observed between the two ceramics. Thermal cycling significantly reduced µSBS.

Effect of Different Surface Treatments on Repair Micro-Shear Bond Strength of An Injectable Composite

Effect of Different Surface Treatments on Repair Micro-Shear Bond Strength of An Injectable Composite

Effect of Ceramic Thickness on the Bond Strength to Resin-Luting Agents before and after Thermal Cycling.

This study investigated microshear bond strength (µSBS) of two (2) dual-cured resin-luting agents (RelyX™ Ultimate and RelyX™ U200) when photoactivated through varying thicknesses of lithium disilicate, with or without thermal cycling. Discs of IPS e.max Press of 0.5, 1.5, and 2 mm in thickness were obtained. Elastomer molds (3.0 mm in thickness) with four cylinder-shaped orifices 1.0 mm in diameter, were placed onto the ceramic surfaces and filled with resin-luting agents. A Mylar strip, glass plate, and load of 250 grams were placed over the filled mold. The load was removed and the resin-luting agents were photoactivated through the ceramics using a single-peak LED (Radii Plus.) All samples were stored in distilled water at 37oC for 24 h. Half of the samples were subjected to thermal cycling (3,000 cycles; 5ºC and 55ºC). All samples were then submitted to µSBS test using a universal testing machine (Instron 4411) at a crosshead speed of 0.5 mm/min. Data were submitted to three-way ANOVA and Tukey post-hoc test (α=0.05). The mean µSBS at 24 h was significantly higher than after thermal cycling (p<0.05). No statistical difference was found between resin-luting agents (p > 0.05). The mean µSBS for groups photoactivated through 0.5 mm ceramic were significantly higher than 1.5 mm and 2.0 mm (p < 0.05). In conclusion, increased ceramic thicknesses reduced the bond strength of tested resin-luting agents to lithium disilicate. No differences were found between resin-luting agents. Thermal cycling reduced the bond strength of both resin-luting agents.