Mg-based Alloys Research Articles

Composite Nanocoatings of Biomedical Magnesium Alloy Implants: Advantages, Mechanisms, and Design Strategies.

The rapid degradation of magnesium (Mg) alloy implants erodes mechanical performance and interfacial bioactivity, thereby limiting their clinical utility. Surface modification is among the solutions to improve corrosion resistance and bioefficacy of Mg alloys. Novel composite coatings that incorporate nanostructures create new opportunities for their expanded use. Particle size dominance and impermeability may increase corrosion resistance and thereby prolong implant service time. Nanoparticles with specific biological effects may be released into the peri-implant microenvironment during the degradation of coatings to promote healing. Composite nanocoatings provide nanoscale surfaces to promote cell adhesion and proliferation. Nanoparticles may activate cellular signaling pathways, while those with porous or core-shell structures may carry antibacterial or immunomodulatory drugs. Composite nanocoatings may promote vascular reendothelialization and osteogenesis, attenuate inflammation, and inhibit bacterial growth, thus increasing their applicability in complex clinical microenvironments such as those of atherosclerosis and open fractures. This review combines the physicochemical properties and biological efficiency of Mg-based alloy biomedical implants to summarize the advantages of composite nanocoatings, analyzes their mechanisms of action, and proposes design and construction strategies, with the purpose of providing a reference for promoting the clinical application of Mg alloy implants and to further the design of nanocoatings.

Development of sustainable novel Mg-Ca-Sc alloys with exceptional corrosion resistance

Mg-based alloys have been widely researched for biomaterial and structural applications as they fulfill several prerequisites, such as lightweight, high specific strength, and good biocompatibility, which are highly desirable. However, a long-standing obstacle to the widespread use of magnesium is its low corrosion resistance and increased cost upon increasing alloying content to enhance corrosion resistance. In this study, we report the effect of the simultaneous addition of rare-earth element (Sc) and non-rare earth element (Ca) maintaining low alloying content (∼ 1 wt%) on the mechanical, tribological, and corrosion behavior of Mg. The novel as-cast Mg-0.6Ca-0.5Sc alloy exhibited excellent corrosion resistance with a corrosion rate ∼ 40 % lower than the conventional as-cast WE43 alloy and ∼ 88 % lower than AZ31 alloy. A finer grain size and strong basal texture were achieved through thermomechanical processing, further enhancing the corrosion resistance of the as-cast novel alloys by ∼ 45 %. Stress corrosion cracking and wear testing in physiological saline solution were also conducted to study the combined effect of stress and corrosive electrolyte. The tensile and compression behavior remained practically the same upon adding Sc. However, the addition of 0.5 wt% Sc reduced the yield asymmetry by ∼ 10 % in as-cast and ∼ 5 % in recrystallized conditions. Furthermore, Mg-0.6Ca-0.5Sc alloy exhibited significant strength (∼ 175 %) and ductility (∼ 67 %) improvement under tensile testing in a physiological saline solution environment compared to Mg-0.6Ca alloy. The developed novel Mg-0.6Ca-0.5Sc ternary alloy exhibited enhanced resistance to corrosion, stress corrosion cracking, and wear relative to the Mg-0.6Ca binary alloy.

Development, Processing and Aging of Novel Zn-Ag-Cu Based Biodegradable Alloys.

The use of biodegradable materials for implants is a promising strategy to overcome known long-term clinical complications related to permanent implants. Ideally, biodegradable implants support the damaged tissue for a certain period and then degrade, while the physiological function of the surrounding tissue is restored. Although Mg-based alloys nearly ideally lend themselves to biodegradable implants, a few critical shortcomings promoted the development of alternative alloy systems. Due to their reasonably good biocompatibility, moderate corrosion rate without hydrogen evolution and adequate mechanical properties, increasing attention has been paid to Zn alloys. In this work, precipitation-hardening alloys in the system Zn-Ag-Cu were developed relying on thermodynamic calculations. After casting the alloys, their microstructures were refined by thermomechanical treatment. The processing was tracked and directed, respectively, by routine investigations of the microstructure, associated with hardness assessments. Although microstructure refinement increased the hardness, the material proved to be susceptible to aging as the homologous temperature of zinc is at 0.43 Tm. Besides mechanical performance and corrosion rate, long-term mechanical stability is another crucial factor that must be taken into consideration to ensure the safety of the implant and thus requires a profound understanding of the aging process.

Investigation of ball-milling process on microstructure, thermodynamics and kinetics of Ce–Mg–Ni-based hydrogen storage alloy

Aiming at improving hydrogen storage performance of Mg-base alloy, the Mg90Ce3Ni7 alloy is prepared by medium-frequency induction melting and following mechanical ball-milling process. X-ray diffraction analysis reveals that the ball-milling Mg90Ce3Ni7 alloy is composed of Mg, Mg2Ni and CeMg12 phases, whereas subsequent milling induces grain refinement and the formation of amorphous phase. In addition, the extension of ball-milling time also not further improve the thermodynamic properties, whereas has a very significant effect on the kinetic properties, which is mainly attributed to the change of microstructure of the alloy by ball milling process. The ball-milling not only creates the nanocrystalline and amorphous structures, but also refines the particle size of the alloy. This is beneficial to the nucleation and diffusion of the alloy during reversible hydrogenation reaction. Concretely, the ball-milling time enhances the kinetics of hydrogen absorption at low temperature, especially for the alloy milled for 20 h, in which can absorb more than 3.5 wt % H2 over 30 min at 100 °C. Meanwhile, the ball-milling time enhances the kinetics of hydrogen desorption. It leads to effectively reducing the dehydrogenation activation energy to 72.2 kJ/mol H2, which allows the alloy can release more than 5 wt % H2 in 10 min at 280 °C. The work provides a scientific way to promote the practical application of Mg-based hydrogen storage alloy.

Microstructure, Biodegradation, and Mechanical Properties of Biodegradable Mg-Based Alloy Containing Calcium for Biomedical Applications

Microstructure, Biodegradation, and Mechanical Properties of Biodegradable Mg-Based Alloy Containing Calcium for Biomedical Applications

Hydrogen absorption/desorption cycling performance of Mg-based alloys with in-situ formed Mg2Ni and LaH (x = 2, 3) nanocrystallines

Aiming to elucidate the hydrogen absorption/desorption cycling properties of Mg-based alloys with in-situ formed Mg2Ni and LaHx (x = 2, 3) nanocrystallines, the hydrogen storage cycle stability, hydriding/dehydriding cycling kinetics and thermodynamic stability of the experimental alloys have been investigated in detail. The results show that the Mg–Ni–La alloys exhibit improved hydrogen storage cycling properties and can remain storage hydrogen above 5.5 wt% after 200 cycles. With the increase of cycling numbers, the dehydrogenation rates of the experimental samples increase firstly and then gradually decrease, and eventually maintain relative stable state. Microstructure observation reveals that powders sintering and hydrogen decrepitation both exist during hydrogen absorption/desorption cycles due to repeated volume expansion and contraction. Meanwhile, the in-situ formed LaHx (x = 2, 3) and Mg2Ni nanocrystallines stabilize the microstructures of the particles and hinder the powders sintering. After 200 cycles, the average particle size of the experimental samples decreases and the specific surface area apparently increases, which leads to the decomposition temperatures of MgH2 and Mg2NiH4 slightly shift to lower temperatures. Moreover, Mg2Ni and LaHx (x = 2, 3) have been proven to be stable catalysts during long-term cycling, which can still uniformly distribute within the powders after 200 cycles.

Microstructural and Electrochemical Influence of Zn in MgCaZn Biodegradable Alloys.

In recent years, biodegradable materials have included magnesium alloys with homogenous disintegration and a controllable degradation rate. Utilized in medical applications, biodegradable materials based on magnesium have been widely explored throughout the years. It is well-known that alloying Mg with biocompatible and non-toxic elements increases the biodegradability of surgical alloys. The purpose of this study was to examine the microstructure and the electrochemical response (corrosion resistance) of a new experimental Mg-based biodegradable alloy-Mg-0.5%Ca with additions of Zn as follows: 0.5, 1.5, and 3.0 wt.% in order to control the corrosion rate. Immersion tests were performed for different periods in a simulated body fluid electrolyte solution at 37 °C, and the mass loss was appreciated in order to calculate the corrosion rate (CR). The investigation led to the discovery of a dendritic Mg solid solution, a lamellar Mg2Ca compound, and a MgZn2 intermetallic phase. Scanning electron microscopy, optical microscopy, and energy dispersive spectroscopy were used for surface analysis after the immersion and electro-corrosion resistance tests. The metallic and ceramic compounds that detached themselves from the sample and passed into the solution were evaluated using the SEM-EDS system. All samples presented a generalized electro-corrosion with anodic and cathodic reactions of similar intensity. The corrosion rate was similar regardless of the percentage of zinc, with a smaller value for a higher than 3 wt.% Zn percentage based on the more protective zinc oxide that appeared on the surface.

Strategies to enhance hydrogen storage performances in bulk Mg-based hydrides

Bulk Mg-based hydrogen storage materials have the potential to provide a low-cost solution to diversify energy storage and transportation. Compared to nano powders which require handling and processing under hydrogen or an inert gas atmosphere, bulk Mg-based alloys are safer and are more oxidation resistant. Conventional methods and existing infrastructures can be used to process and handle these materials. However, bulk Mg alloys have smaller specific surface areas, resulting in slower hydrogen sorption kinetics, higher equilibrium temperatures, and enthalpies of hydride formation. This work reviews the effects of the additions of a list of alloying elements and the use of innovative processing methods, e.g., rapid solidification and severe plastic deformation processes, to overcome these drawbacks. The challenges, advantages, and weaknesses of each method and future perspectives for the development of Mg-based hydrogen storage materials are discussed.

Additive manufacturing of biodegradable magnesium-based materials: Design strategies, properties, and biomedical applications

Magnesium (Mg)-based materials are a new generation of alloys with the exclusive ability to be biodegradable within the human/animal body. In addition to biodegradability, their inherent biocompatibility and similar-to-bone density make Mg-based alloys good candidates for fabricating surgical bioimplants for use in orthopedic and traumatology treatments. To this end, nowadays additive manufacturing (AM) along with three-dimensional (3D) printing represents a promising manufacturing technique as it allows for the integration of bioimplant design and manufacturing processes specific to given applications. Meanwhile, this technique also faces many new challenges associated with the properties of Mg-based alloys, including high chemical reactivity, potential for combustion, and low vaporization temperature. In this review article, various AM processes to fabricate biomedical implants from Mg-based alloys, along with their metallic microstructure, mechanical properties, biodegradability, biocompatibility, and antibacterial properties, as well as various post-AM treatments were critically reviewed. Also, the challenges and issues involved in AM processes from the perspectives of bioimplant design, properties, and applications were identified; the possibilities and potential scope of the Mg-based scaffolds/implants are discussed and highlighted.

A novel method towards improving the hydrogen storage properties of hypoeutectic Mg-Ni alloy via ultrasonic treatment

Ultrasonic treatment has great contributions on modifying the morphology, dimension and distribution of constituent phases during solidification, which serve as dominate factors influencing the hydrogen storage performance of Mg-based alloys. In this research, ultrasonic treatment is utilized as a novel method to enhance the de-/hydriding properties of Mg-2Ni (at.%) alloy. Due to ultrasonic treatment, the microstructure of as-cast alloy is significantly refined and homogenized. Ascribing to the increased eutectic boundaries and shortened distance inside α-Mg for hydrogen atoms diffusion, the hydrogen uptake capacities and isothermal de-/hydriding rates improve effectively, especially at lower temperature. The peak desorption temperature reduces from 392.99 °C to 345.56 °C, and the dehydriding activation energy decreases from 101.93 kJ mol−1 to 88.65 kJ mol−1. Weakened hysteresis of plateau pressures and slightly optimized thermodynamics are determined from the pressure-composition isotherms. Owing to the refined primary Mg, a larger amount of hydrogen with the higher hydriding proportion is absorbed in the first stage when hydrides nucleate in eutectic region and grow on primary Mg periphery subsequently before MgH2 colonies impinging, resulting in the enhancement of hydrogenation rates and capacities.

Study on Material Design and Corrosion Resistance Based on Multi-Principal Component Alloying Theory.

This study mainly attempts to develop Mg-based alloy materials with excellent corrosion resistance by means of multi-principal alloying. The alloy elements are determined based on the multi-principal alloy elements and the performance requirements of the components of biomaterials. Mg30Zn30Sn30Sr5Bi5 alloy was successfully prepared by vacuum magnetic levitation melting. Through the electrochemical corrosion test with m-SBF solution (pH7.4) as the electrolyte, the corrosion rate of alloy Mg30Zn30Sn30Sr5Bi5 alloy decreased to 20% of pure Mg. It could also be seen from the polarization curve that when the self-corrosion current density is low, the alloy shows superior corrosion resistance. Nevertheless, with the increase in self-corrosion current density, although the anodic corrosion performance of the alloy is obviously better than that of pure Mg, the cathode shows the opposite situation. The Nyquist diagram shows that the self-corrosion potential of the alloy is much higher than that of pure Mg. In general, under the condition of low self-corrosion current density, the alloy materials display excellent corrosion resistance. It is proved that the multi-principal alloying method is of positive significance for improving the corrosion resistance of Mg alloys.

Deformation-induced dynamic precipitation of 14H-LPSO structure and its effect on dynamic recrystallization in hot-extruded Mg-Y-Zn alloys

Understanding dynamic precipitation in thermo-mechanical processing can shed light on the manufacturing of high-performance Mg-based alloys. This study investigates the dynamic precipitation of long-period stacking order (LPSO) phase with 14H structure and its effect on dynamic recrystallization (DRX) in the hot-extruded Mg98.5Y1Zn0.5, Mg97Y2Zn1 and Mg94Y4Zn2 (at. %) alloys. First, the simultaneous increase of Y and Zn atoms not only promotes the formation of interdendritic block 18R-LPSO phases during solidification but also facilitates the dynamic precipitation of intragranular lamellar and thin 14H-LPSO phases in coarse non-DRX and fine DRX grains, respectively, during hot extrusion. Second, the increased block 18R volume fraction and lamellar 14H number density significantly delays DRX. However, as the deformation strain increases, broken 18R fragments accelerate the DRX particle-stimulated nucleation (PSN) mechanism and fluctuant α-Mg/18R interfaces initiate the discontinuous DRX mechanism. In particular, the deformation kinking and dissolving of lamellar 14H activate the continuous DRX mechanism. Finally, the mechanical strength increases but ductility decreases with increasing the content of Y and Zn atoms for the hot-extruded Mg-Y-Zn alloys. The high strength of the hot-extruded Mg94Y4Zn2 alloy is attributed to fine DRX grain size, strong un-DRX grains, major block 18R and lamellar/thin 14H phases, and deformation kinking, while the high ductility of the hot-extruded Mg98.5Y1Zn0.5 alloy is responsible for large DRX volume fraction, high activity of deformation twins, and easy mobility of basal slip.

Characteristics of Mg-Based Sintered Alloy with Au Addition

The magnesium-based alloys produced by mechanical alloying (MA) are characterized by specific porosity, fine-grained structure, and isotropic properties. In addition, alloys containing magnesium, zinc, calcium, and the noble element gold are biocompatible, so they can be used for biomedical implants. The paper assesses selected mechanical properties and the structure of the Mg63Zn30Ca4Au3 as a potential biodegradable biomaterial. The alloy was produced by mechanical synthesis with a milling time of 13 h, and sintered via spark-plasma sintering (SPS) carried out at a temperature of 350 °C and a compaction pressure of 50 MPa, with a holding time of 4 min and a heating rate of 50 °C∙min-1 to 300 °C and 25 °C∙min-1 from 300 to 350 °C. The article presents the results of the X-ray diffraction (XRD) method, density, scanning electron microscopy (SEM), particle size distributions, and Vickers microhardness and electrochemical properties via electrochemical impedance spectroscopy (EIS) and potentiodynamic immersion testing. The obtained results reveal the compressive strength of 216 MPa and Young's modulus of 2530 MPa. The structure comprises MgZn2 and Mg3Au phases formed during the mechanical synthesis, and Mg7Zn3 that has been formed during the sintering process. Although MgZn2 and Mg7Zn3 improve the corrosion resistance of the Mg-based alloys, it has been revealed that the double layer formed because of contact with the Ringer's solution is not an effective barrier; hence, more data and optimization are necessary.

Hydrogen storage property improvement of La–Y–Mg–Ni alloy by ball milling with TiF3

Ball milling the powders of Mg-based alloys with transition metal compounds is effective for improving their hydrogen storage performances. In this experiment, the alloys of La1.7Y0.3Mg16Ni + x wt.% TiF3 (x = 0–10) were prepared through mechanical milling technology. XRD, SEM, HRTEM and granulometry were used to measure the composition and microstructure of alloys. The isothermal hydrogen storage property was measured by a Sievert apparatus. The results reveal that the TiF3 additive in ball-milled samples transforms into MgF2 and TiH2 after the first hydrogen absorption. Adding TiF3 enhances the crystallinity and reduces the average particle and crystallite sizes of alloys, which is beneficial to accelerating hydriding and dehydriding kinetics. Adding 7 wt% TiF3 into alloy decreases the dehydrogenation activation energy from 72.2 to 64.0 kJ/mol and improves the hydrogen absorption rate at low temperatures, absorbing 3.50 wt% H in 0.5 min at 323 K.

Compositional and thermophysical study of Al–Si- and Zn–Al–Mg-based eutectic alloys for latent heat storage

Abstract In this study, the eutectic temperature and latent heat of Al–Si- and Zn–Al–Mg-based eutectic alloys were determined using differential thermal analysis (DTA) and differential scanning calorimetry measurements in order to identify eutectic alloys for latent heat storage in the eutectic temperature ranges of 450–550 and 300–350°C. First, the eutectic compositions of the Al–Si–Cu–Mg–Zn and Zn–Al–Mg–Sn alloys were identified using scanning electron microscopy with energy-dispersive X-ray spectroscopy and DTA in two steps. In the second step, metallographic analysis was repeated until a uniform eutectic microstructure was obtained. Thermophysical analysis revealed that the eutectic temperatures of several types of Al–Si- and Zn–Al–Mg-based eutectic alloys were within the targeted temperature ranges with relatively high latent heat. These results confirmed that Al–Si- and Zn–Al–Mg-based eutectic alloys have suitable properties as phase change materials for use in the 300–350 and 450–550°C temperature ranges.

Attaining High Functional Performance in Biodegradable Mg-Alloys: An Overview of Challenges and Prospects for the Mg-Zn-Ca System.

This article presents a concise overview of modern achievements and existing knowledge gaps in the area of biodegradable magnesium alloys. Hundreds of Mg-based alloys have been proposed as candidates for temporary implants, and this number tends to increase day by day. Therefore, while reviewing common aspects of research in this field, we confine ourselves primarily to the popular Mg-Zn-Ca system, taken as a representative example. Over the last decades, research activities in this area have grown enormously and have produced many exciting results. Aiming at highlighting the areas where research efforts are still scarce, we review the state-of-the-art processing techniques and summarize the functional properties attained via a wide variety of processing routes devised towards achieving a desired properties profile, including the mechanical response in terms of strength, ductility, and fatigue resistance paired with biocompatibility and bio-corrosion resistance or controlled degradability. We pay keen attention to a summary of corrosion properties and mechano-chemical interactions between an aggressive environment and loaded Mg-based structures, resulting in stress corrosion cracking and premature corrosion fatigue failures. The polemic issues and challenges practitioners face in their laboratory research are identified and discussed.

The Effects of Sirolimus and Magnesium on Primary Human Coronary Endothelial Cells: An In Vitro Study.

Drug eluting magnesium (Mg) bioresorbable scaffolds represent a novel paradigm in percutaneous coronary intervention because Mg-based alloys are biocompatible, have adequate mechanical properties and can be resorbed without adverse events. Importantly, Mg is fundamental in many biological processes, mitigates the inflammatory response and is beneficial for the endothelium. Sirolimus is widely used as an antiproliferative agent in drug eluting stents to inhibit the proliferation of smooth muscle cells, thus reducing the occurrence of stent restenosis. Little is known about the potential interplay between sirolimus and Mg in cultured human coronary artery endothelial cells (hCAEC). Therefore, the cells were treated with sirolimus in the presence of different concentrations of extracellular Mg. Cell viability, migration, barrier function, adhesivity and nitric oxide synthesis were assessed. Sirolimus impairs the viability of subconfluent, but not of confluent cells independently from the concentration of Mg in the culture medium. In confluent cells, sirolimus inhibits migration, while it cooperates with Mg in exerting an anti-inflammatory action that might have a role in preventing restenosis and thrombosis.

Influence of the Zn interlayer on the mechanical strength, corrosion and microstructural behavior of friction stir-welded 6061-T6 aluminium alloy and AZ61 magnesium alloy dissimilar joints

To reduce structural weight, the transportation industry needs to join dissimilar Al and Mg alloys. However, due to their different properties, joining dissimilar materials is much harder than joining identical ones. Brittle intermetallic compounds (IMCs) make it difficult to produce strong Al/Mg joints even with friction stir welding (FSW). Mechanical and corrosion properties are important for joint protection over time. Mg-based alloys corrode preferentially in dissimilar Al/Mg joints due to their lower corrosion potential. Consequently, this study introduces a novel interlayer-based strategy to address this issue. Therefore, this study explored the influence of Zn interlayers on the mechanical properties, microstructure, and corrosion behaviors of Al6061-T6 and AZ61 Mg alloy FSW butt joints. A scanning electron microscope, a transmission electron microscope, X-ray photoelectron spectroscopy, X-Ray diffraction, and an energy dispersive spectrometer were used to observe and characterise the microstructures and IMCs formation at the interface of Al/Mg welded joints. In Zn-added FSW joints, finer and better-distributed Mg-Zn IMCs form in place of the brittle Al-Mg IMCs (multilayered structure) observed in Zn free Al/Mg joints. Moreover, the addition of Zn significantly improved the joints' tensile strength through the proper dispersion and distribution of the zinc interlayer in the weld zone. In this way, a tensile strength of 198.85 MPa was attained, 34.17% greater than a Zn free Al/Mg joint. Furthermore, immersion tests revealed that the weld joints of Al/Mg with Zn are more resistant to corrosion than the joints of Al/Mg, resulting in a 12.78% lessening in weight loss compared with a Zn free joint. The reason for that is the Zn interlayer's ability to reduce the dissimilar metal corrosion amid the base materials.

Synthesis of Magnesium-Based Alloys by Mechanical Alloying for Implant Applications

The biocompatibility and biodegradability of magnesium (Mg), along with its lightness, make magnesium-based materials promising for use in the biomedical industry. In this work, ternary Mg–Zn–Ca alloys were manufactured for biomedical applications using mechanical alloying (MA). The objective of this work was to study the effect of milling time on the produced ternary alloys Mg65–Zn30–Ca5 and Mg70–Zn25–Ca5 (percentages by weight), the degradation of the alloys in synthetic human fluids, and their generated cytotoxicity. The Mg-based alloys were synthesized in a planetary ball mill under an argon atmosphere using stainless-steel containers and balls with a milling regimen of 400 rpm for 2, 5, 10, 15, and 20 h. The powders obtained after MA were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD), which verified that ternary Mg–Zn–Ca alloys can be obtained using MA. The XRD refinement analysis of the samples showed the presence of a MgZn intermetallic phase. Electrochemical tests showed that the corrosion resistance and corrosion current density of Mg65–Zn30–Ca5 and Mg70–Zn25–Ca5 alloys improved compared to those of pure Mg. Cytotoxicity testing was conducted using the Sulforhodamine B (SRB) assay, which revealed that the alloys did not exhibit cytotoxicity toward human fibroblast cells. Mg65–Zn30–Ca5 and Mg70–Zn25–Ca5 alloys show good potential to be used in biomedical applications.

Magnesium-based alloys with adapted interfaces for bone implants and tissue engineering.

Magnesium and its alloys are one of the most used materials for bone implants and tissue engineering. They are characterized by numerous advantages such as biodegradability, high biocompatibility and mechanical properties with values close to the human bone. Unfortunately, the implant surface must be adequately tuned, or Mg-based alloys must be alloyed with other chemical elements due to their increased corrosion effect in physiological media. This article reviews the clinical challenges related to bone repair and regeneration, classifying bone defects and presenting some of the most used and modern therapies for bone injuries, such as Ilizarov or Masquelet techniques or stem cell treatments. The implant interface challenges are related to new bone formation and fracture healing, implant degradation and hydrogen release. A detailed analysis of mechanical properties during implant degradation is extensively described based on different literature studies that included in vitro and in vivo tests correlated with material properties' characterization. Mg-based trauma implants such as plates and screws, intramedullary nails, Herbert screws, spine cages, rings for joint treatment and regenerative scaffolds are presented, taking into consideration their manufacturing technology, the implant geometrical dimensions and shape, the type of in vivo or in vitro studies and fracture localization. Modern technologies that modify or adapt the Mg-based implant interfaces are described by presenting the main surface microstructural modifications, physical deposition and chemical conversion coatings. The last part of the article provides some recommendations from a translational perspective, identifies the challenges associated with Mg-based implants and presents some future opportunities. This review outlines the available literature on trauma and regenerative bone implants and describes the main techniques used to control the alloy corrosion rate and the cellular environment of the implant.