Methyl Ether Research Articles

Communication — The Impact of Co-solvent Selection for Dimethyl-2,5-dioxahexane carboxylate in Sodium Ion Batteries

Traditional linear carbonates including dimethyl carbonate (DMC), diethyl carbonate (DEC), and ethyl methyl carbonate (EMC) were investigated as co-solvents for the dimethyl-2,5-dioxahexane carboxylate (DMOHC)-based electrolyte in Na0.97Ca0.03[Mn0.39Fe0.31Ni0.22Zn0.08]O2 (NCMFNZO)/hard carbon (HC) pouch cells. The EMC-containing cell displays excellent electrochemical performance, exhibiting only a 1.6 mAh irreversible capacity loss during 500 h of storage at 4 V and 40 °C, and maintaining over 80% capacity retention after 200 cycles up to 4 V at 40 °C. Severe gas evolution and Na plating issues are present in all the tested systems.

Interphase‐Designable Additive‐Enabled Ethylene Carbonate‐Free Electrolyte for Wide‐Temperature, Long‐Cycling, High‐Voltage Lithium Metal Batteries

AbstractIncreasing the upper cut‐off voltage of the LiNixCoyMn1‐x‐yO2 (NCM)‐based lithium‐metal batteries (LMBs) is highly pursued for achieving high battery energy density. However, the cycling stability of high‐voltage LMBs, which is associated with ethylene carbonate electrolytes, remains greatly challenging. Herein, an interphase‐designable additive‐enabled ethylene carbonate‐free electrolyte strategy is proposed for achieving 4.6 V Li||NCM811 battery with long cycling life from 55 to −30 °C. The solvent characteristics of ethyl methyl carbonate endow LMBs with potential merits in high voltage, wide temperature, and cycling stability, which are further strengthened by the additive, 1,5‐difluoro‐2,4‐dinitrobenzene (FNB), for optimizing electrode electrolyte interphases. The sturdy LiF‐rich and LiNxOy‐contained electrode/electrolyte interphase on cathode/anode surfaces can protect two electrodes well from electrolyte corrosion and also reduce excessive electrolyte decomposition. As expected, the Li||NCM811 batteries can maintain 70% capacity retention after 500 cycles with superior high‐temperature and low‐temperature performance (from 55 to −30 °C). The 6.8Ah pouch cells with this electrolyte can achieve a high energy density of up to 505 Wh kg−1.

Intramolecular Hydrogen Bonding Rigidifying Flexible Bridge for Solution- and Vacuum-Processed TSCT-TADF Emitters.

To realize strong donor-acceptor face-to-face stacking for efficient through-space charge transfer-type thermally activated delayed fluorescence, a conceptually new design strategy is proposed to couple flexible bridges with adequate rigidity via built-in intramolecular hydrogen bonds (IHBs). The resulting emitter ACE-CN has a planarized benzyl methyl ether bridge self-anchored by the C-H···O IHB and shows a high photoluminescence quantum efficiency of 93%. The solution- and vacuum-processed devices exhibited high external quantum efficiencies of 11.8% and 24.7%, respectively.

Deciphering the Lipid-Random Copolymer Interactions and Encoding Their Properties to Design a Hybrid System.

Lipid/copolymer colloidal systems are deemed hybrid materials with unique properties and functionalities. Their hybrid nature leads to complex interfacial phenomena, which have not been fully encoded yet, navigating their properties. Moving toward in-depth knowledge of such systems, a comprehensive investigation of them is imperative. In the present study, hybrid lipid/copolymer structures were fabricated and examined by a gamut of techniques, including dynamic light scattering, fluorescence spectroscopy, cryogenic transmission electron microscopy, microcalorimetry, and high-resolution ultrasound spectroscopy. The biomaterials that were mixed for this purpose at different ratios were 1,2-dioctadecanoyl-sn-glycero-3-phosphocholine and four different linear, statistical (random) amphiphilic copolymers, consisting of oligo(ethylene glycol) methyl ether methacrylate as the hydrophilic comonomer and lauryl methacrylate as the hydrophobic one. The colloidal dispersions were studied for lipid/copolymer interactions regarding their physicochemical, morphological, and biophysical behavior. Their membrane properties and interactions with serum proteins were also studied. The aforementioned techniques confirmed the hybrid nature of the systems and the location of the copolymer in the structure. More importantly, the random architecture of the copolymers, the hydrophobic-to-hydrophilic balance of the nanoplatforms, and the lipid-to-polymer ratio are highlighted as the main design-influencing factors. Elucidating the lipid/copolymer interactions would contribute to the translation of hybrid nanoparticle performance and, thus, their rational design for multiple applications, including drug delivery.

Ethylene Polymerizations Catalyzed by Fluorinated "Sandwich" Diimine-Nickel and Palladium Complexes.

Nickel and palladium complexes bearing "sandwich" diimine ligands with perfluorinated aryl caps have been synthesized, characterized, and explored in ethylene polymerization reactions. The X-ray crystallographic analysis of the precatalysts 16 and 6b shows differences from their nonfluorinated analogues 17 and 19, with the perfluorinated aryl caps centered precisely over the nickel and palladium centers, which results in higher buried volumes of the metal centers relative to the nonfluorinated analogues. The sandwich diimine-palladium complexes 5a and 5b containing perfluorinated aryl caps polymerize ethylene in a controlled fashion with activities that are substantially increased compared with their nonfluorinated analogues. Migratory insertion rates in relevant methyl ethylene complexes agree with the activities exhibited in bulk polymerization experiments. DFT studies suggest that facility of ethylene rotation from its preferred orientation perpendicular to the Pd-alkyl bond into a parallel in-plane conformation contributes to the higher polymerization activity for 5b relative to 18a. For these palladium systems, polymer molecular weights can be controlled via hydrogen addition (hydrogenolysis), which is unusual for late-transition-metal-catalyzed olefin polymerizations with no catalyst deactivation occurring. Sandwich diimine-nickel complexes 6a and 6b with perfluorinated aryl caps show ethylene polymerization activities that are about half of those of classical tetraisopropyl-substituted catalyst 2 but again are more active than the analogous nonfluorinated sandwich complexes. Ethylene polymerizations exhibit living behavior, and branched ultrahigh-molecular-weight polyethylenes (UHMWPEs) with very low-molecular-weight distributions (less than 1.1) are obtained. The activated nickel catalysts are stable in the absence of monomer and show good long-term stability at 25 °C.

Controlled Amphiphilicity and Thermo-Responsiveness of Functional Copolymers Based on Oligo(Ethylene Glycol) Methyl Ether Methacrylates

Controlled Amphiphilicity and Thermo-Responsiveness of Functional Copolymers Based on Oligo(Ethylene Glycol) Methyl Ether Methacrylates

Laminar Combustion Characteristics of Spherically Propagating Ethyl Methyl Carbonate Flames

Laminar Combustion Characteristics of Spherically Propagating Ethyl Methyl Carbonate Flames

Crucial Roles of Ethyl Methyl Carbonate in Lithium-Ion and Dual-Ion Batteries: A Review.

The essential role of electrolyte solutions in traditional electrochemical energy storage devices is crucial to enhancing their performance. Consequently, a wide array of electrolyte mixtures along with diverse electrodes have been extensively explored across different models of secondary batteries. Fascinatingly, the role of ethyl methyl carbonate (EMC) as a key cosolvent in the electrolyte mixture of commercial lithium-ion batteries with a graphite anode is garnering growing attention in alternative rechargeable dual-ion batteries utilizing graphite cathodes. In this context, the advancement and function of EMC as a solvent in electrolyte mixtures for lithium-ion and dual-ion batteries were extensively and thoroughly examined in this analysis, encompassing the genesis, synthesis process, and diverse characteristics for the practical uses of these batteries. Here, the review aims to guide readers in understanding EMC's function and impact as a cosolvent in electrolyte mixtures for both major secondary lithium-ion and dual-ion batteries, considering their distinct physicochemical characteristics.

Preparation and performance evaluation of intelligent plugging agent for thermo‐sensitive water‐based drilling fluid

AbstractIn the process of unconventional oil and gas exploitation, the invasion of a large amount of drilling fluid into the formation is one of the most critical reasons leading to wellbore instability. A temperature‐sensitive polymer (AOS) was synthesized from acrylamide, oligo (ethylene glycol) methyl ether methacrylate (OEGMA), and sodium p‐styrene sulfonate by emulsion polymerization. The material is a solid‐free fluid with good fluidity at room temperature, after injection into the formation, the fluid is gradually transformed into hard gel above the lower critical solution temperature (LCST) (90°C), thus blocking micro‐fractures and improving wellbore stability. Infrared and NMR characterization confirmed the successful preparation of the target product. The transmittance of AOS with ambient temperature was measured by UV–vis spectrophotometer, and the LCST behavior of AOS was verified by rheological and viscoelastic measurements. The interaction mechanism between AOS and sodium bentonite was evaluated according to the American Petroleum Institute standard. The results show that after aging at 180°C, the filtration loss is reduced by 93%, and the medium permeability (100, 200 mD) formation is effectively plugged, with a plugging efficiency is as high as 74.7%.

Hybrid Nanoparticles from Random Polyelectrolytes and Carbon Dots.

The present study concerns the preparation of hybrid nanostructures composed of carbon dots (CDs) synthesized in our lab and a double-hydrophilic poly(2-dimethylaminoethyl methacrylate-co-oligo(ethylene glycol) methyl ether methacrylate) (P(DMAEMA-co-OEGMA)) random copolymer through electrostatic interactions between the negatively charged CDs and the positively charged DMAEMA segments of the copolymer. The synthesis of P(DMAEMA-co-OEGMA) copolymer was conducted through RAFT polymerization. Furthermore, the copolymer was converted into a strong cationic random polyelectrolyte through quaternization of the amine groups of DMAEMA segments with methyl iodide (CH3I), and it was subsequently utilized for the complexation with the carbon dots. The molecular, physicochemical, and photophysical characterization of the aqueous solution of the copolymers and their hybrid nanoparticles was conducted using dynamic and electrophoretic light scattering (DLS, ELS) and spectroscopic techniques, such as UV-Vis, fluorescence (FS), and FT-IR spectroscopy. In addition, studies of their aqueous solution using DLS and ELS showed their responsiveness to external stimuli (pH, temperature, ionic strength). Finally, the interaction of selected hybrid nanoparticles with iron (III) ions was confirmed through FS spectroscopy, demonstrating their potential application for heavy metal ions sensing.

The isolation strategy and chemical analysis of oil cells from Asari Radix et Rhizoma.

Single-cell analysis, a rapidly evolving field, encounters significant challenges in detecting individual cells within complex plant tissues, particularly oil cells (OCs). The intricate process of single-cell isolation, coupled with the inherent chemical volatility of oil cells, necessitates a comprehensive methodology. This study presents a method for obtaining intact OC from Asari Radix et Rhizoma (ARR), a traditional herbal medicine. The developed approach facilitates both qualitative and quantitative analysis of diverse OCs. To determine the most reliable approach, four practical methods-laser capture microdissection, micromanipulation capturing, micromanipulation piping, and cell picking-were systematically compared and evaluated, unequivocally establishing cell picking as the most effective method for OC isolation and chemical analysis. Microscopic observations showed that OCs predominantly distribute in the cortex of adventitious and fibrous roots, as well as the pith and cortex of the rhizome, with distinct morphologies-oblong in roots and circular in rhizomes. Sixty-three volatile constituents were identified in OCs, with eighteen compounds exhibiting significant differences. Safrole, methyleugenol, and asaricin emerged as the most abundant constituents in OCs. Notably, cis-4-thujanol and tetramethylpyrazine were exclusive to rhizome OCs, while isoeugenol methyl ether was specific to fibrous root OCs based on the detections. ARR roots and rhizomes displayed marked disparities in OC distribution, morphology, and constituents. The study highlights the efficacy of cell picking coupled with HS-SPME-GC-MS as a flexible, reliable, and sensitive method for OC isolation and chemical analysis, providing a robust methodology for future endeavors in single-cell analyses.

Vinyl and methyl-ester groups in the insoluble polymer drug patiromer identified and quantified by solid-state NMR

Patiromer (Veltassa®) is a crosslinked, insoluble co-polymer drug used as a nonabsorbent potassium binder, approved for treatment of hyperkalemia. Quantitative solid-state 13C nuclear magnetic resonance (NMR) analysis with comprehensive peak assignment, component quantification, and calculation of mole and weight fractions of monomer units was performed on three doses of patiromer. The workflow is documented in detail. Spectrally edited solid-state 13C NMR spectra of patiromer show =CHn peaks of matching intensity at 116 and 141 ppm, characteristic of -CH=CH2 vinyl groups. Similar spectral features can be observed in earlier studies but were previously ignored. In this study, the vinyl signals are well-resolved in a 2-s direct polarization (DP) spectrum without and with dipolar dephasing, which confirms that these sp2-hybridized carbons are bonded to hydrogen and partially mobile, consistent with vinyl side groups from incompletely reacted divinyl crosslinkers. The vinyl groups account for 1.6% of all carbon, 3% of the monomer units, and nearly 1/3 of the crosslinkers. Furthermore, an unexpected OCH3 moiety accounting for ∼1.2% of all carbons was identified by spectral editing; its chemical shift of 54 ppm is more consistent with a methyl ester than with a methyl ether. It can originate from incomplete hydrolysis of ∼6% of methyl-2-fluoroacrylate, the main monomer of patiromer. Characteristic cross peaks in two-dimensional 1H–13C heteronuclear correlation NMR confirm the presence of the vinyl and OCH3 groups. Trace amounts of xanthan gum are also detected. The quantitative 13C NMR spectrum of patiromer has been matched in a simulation using a model with five monomer units.

Differential Resistance to Acetyl-CoA Carboxylase Inhibitors in Rice: Insights from Two Distinct Target-Site Mutations.

Weeds present a significant challenge to agricultural productivity, and acetyl-CoA carboxylase (ACCase)-inhibiting herbicides have proven to be effective in managing weed populations in rice fields. To develop ACCase-inhibiting herbicide-resistant rice, we generated mutants of rice ACCase (OsACC) featuring Ile-1792-Leu or Gly-2107-Ser substitutions through ethyl methyl sulfonate (EMS) mutagenesis. The Ile-1792-Leu mutant displayed cross-resistance to aryloxyphenoxypropionate (APP) and phenylpyrazoline (DEN) herbicides, whereas the Gly-2107-Ser mutants primarily exhibited cross-resistance to APP herbicides with diminished resistance to the DEN herbicide. In vitro assays of the OsACC activity revealed an increase in resistance to haloxyfop and quizalofop, ranging from 4.84- to 29-fold in the mutants compared to that in wild-type. Structural modeling revealed that both mutations likely reduce the binding affinity between OsACC and ACCase inhibitors, thereby imparting resistance. This study offers insights into two target-site mutations, contributing to the breeding of herbicide-resistant rice and presenting alternative weed management strategies in rice cultivation.

Closing the Gap Between Gas Phase and Condensed Phase: Fragmentation Studies of the Thiomethoxymethyl Complex [(bipy)Pt(CH3)2(CH2SCH3)]+

AbstractCollision‐induced dissociation (CID) of the mass‐selected cation [(bipy)Pt(CH3)2(CH2SCH3)]+ in an ion‐trap mass‐spectrometer results in the losses of the neutrals ethane, ethene, dimethyl sulfide, methane, ethyl methyl sulfide, and propane. The generation of the first four neutrals is also observed, when the isolated, dimeric complex [(bipy)Pt(CH3)2(CH2SCH3)]2[SbF6]2 is heated in the condensed phase. While the product distribution is very similar regardless of whether the complex is heated in the solid state or in solution, ethane loss, i. e. the quite rare event of an sp3‐sp3 C−C reductive elimination from a platinum(IV) complex, dominates in the gas‐phase experiment. However, when the counter anion [SbF6]− is exchanged by the more weakly coordinating anion [BAr4F]−, the amounts of ethane and ethene are increased also in the condensed phase. These sum of observations indicates the similarities of the fragmentation of [(bipy)Pt(CH3)2(CH2SCH3)]+ in both phases. Thus, a correlation of processes in both environments is possible for selected systems (and particularly for unimolecular processes), but the choice of the proper conditions is crucial for a meaningful comparison.

Rapid attainment of full wettability through surface PEGylation of hydrophobic polyvinylidene fluoride membranes via spray-coating for enhanced anti-biofouling performances

This manuscript explores the development of antifouling membranes fabricated by vapor-induced phase separation (VIPS) process and their spray-coating modification with an aqueous solution of a copolymer comprising butyl methacrylate and poly(ethylene glycol) methyl ether methacrylate, designated as poly(BMA-r-PEGMA). An initial optimization phase focused on improving the modification quality, with the aim of enhancing the wettability on both the top and bottom surfaces of the membranes, despite spraying on the top surface only. Our findings reveal that a sprayed solution concentration of 10 mg/mL, a pressure of 0.25 MPa, and a scan rate of 3000 mm/min achieved a decrease in water contact angle to 0 in less than 12 s for both membrane surfaces (the top surface directly exposed to the spray, and the bottom surface facing the instrument stage), suggesting that the spray-coating modifies the entire membrane’s bulk. The presence of the copolymer on both surfaces was also evidenced by FTIR and XPS tests. Further biofouling assessments demonstrated the performances of the optimized membrane (OM). In static attachment tests, the OM exhibited a high reduction in Escherichia coli adhesion, with less than 10 % adhering bacteria, compared to unmodified membranes. During the filtration of bacteria-containing wastewater, the OM boasted a flux recovery ratio approaching 60 % (against less than 40 % for a commercial hydrophilic membrane), a rejection rate of 99.3 %, and a water permeability of 2500 LMH/bar. Moreover, the OM was stable over a 4-week period, with a resistance to E. coli attachment remaining similar to prior immersion. These findings underscore the significant potential of spray-coating to develop stable and effective antifouling microfiltration membranes for the removal of microorganisms from wastewater.

Asymmetric Aldol Reactions Catalyzed by Polymeric Self-Assembly with Side-Chain Dipeptide Pendants.

To explore the role of proline amide moieties in polymer-supported organocatalysts, side-chain l-proline-l-alanine (Pro-Ala) dipeptide-containing block copolymers were synthesized, and their catalytic potential for the aldol reaction was explored. The dipeptide monomer (Boc-Pro-Ala-HEMA) was polymerized to prepare block copolymers in the presence of hydrophilic poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMA) and hydrophobic poly(methyl methacrylate) (PMMA) macro-chain transfer agents. Boc group expulsion from the block copolymers produced double hydrophilic PPEGMA-b-P(Pro-Ala-HEMA) (1b) and amphiphilic PMMA-b-P(Pro-Ala-HEMA) (1c) polymers. The solution behaviors of the polymers were studied by various physical techniques, which showed the formation of self-assembled aggregates of 1c in water and N,N-dimethylformamide (DMF)/water solvent mixtures. These polymers are used as organocatalysts during the aldol reaction of cyclohexanone and 4-nitrobenzaldehyde in different solvent polarities, catalyst loadings, temperatures, and reaction times. This work emphasizes superior catalytic activity of 1c at lower catalyst loadings (5%) while maintaining high conversion (95%) and enantioselectivity (94%) across multiple recycling cycles in DMF/water at a 3:1 ratio (v/v).

Four-Component Statistical Copolymers by RAFT Polymerization.

This manuscript serves as the starting point for in-depth research of multicomponent, statistical, methacrylate-based copolymers that potentially mimic the behavior of proteins in aqueous solutions. These synthetic macromolecules are composed of specially chosen comonomers: methacrylic acid (MAA), oligoethylene glycol methyl ether methacrylate (OEGMA475), 2-(dimethylamino)ethyl methacrylate (DMAEMA) and benzyl methacrylate (BzMA). Monomer choice was based on factors such as the chemical nature of pendant functional groups, the polyelectrolyte/polyampholyte and amphiphilic character and the overall hydrophobic-hydrophilic balance (HLB) of the obtained quaterpolymers. Their synthesis was achieved via a one-pot reversible addition fragmentation chain transfer (RAFT) polymerization in two distinct compositions and molecular architectures, linear and hyperbranched, respectively, in order to explore the effects of macromolecular topology. The resulting statistical quaterpolymers were characterized via 1H-NMR and ATR-FTIR spectroscopies. Their behavior in aqueous solutions was studied by dynamic (DLS) and electrophoretic light scattering (ELS) and fluorescence spectroscopy (FS), producing vital information concerning their self-assembly and the structure of the formed aggregates. The physicochemical studies were extended by tuning parameters such as the solution pH and ionic strength. Finally, the quaterpolymer behavior in FBS/PBS solutions was investigated to test their colloid stability and biocompatibility in an in vivo-mimicking, biological fluid environment.

Unravelling Competitive Interactions between Polymer Side Chains and End Groups with β-Cyclodextrin.

This study investigates unexpected competitive host-guest interactions of β-cyclodextrin (β-CD), which can occur with polymers in aqueous solution, using the examples of the two polymers poly(oligo(ethylene glycol) methyl ether methacrylate) and poly(glycerol mono methacrylate). Systematic structural modifications of the polymer provide insight into the host-guest interaction with β-CD and the competition between side chains and end groups such as hydrophobic end groups remaining from reversible addition fragmentation chain transfer polymerization or intentionally implemented molecular recognition units such as arylazopyrazole photoswitches.

Development of Perfluoro Decalin/Fluorinated Polyimide Core-Shell Microparticles via SPG Membrane Emulsification Using Methyl Perfluoropropyl Ether Cosolvent.

Red blood cell-inspired perfluorocarbon-encapsulated core-shell particles have been developed for biomedical applications. Although the use of perfluorodecalin (FDC) is expected for core-shell particles owing to its high oxygen solubility, the low solubility of FDC in any organic solvent, owing to its fluorous properties, prevents its use in core-shell particles. In this study, a new cosolvent system composed of dichloromethane (DCM) and heptafluoropropyl methyl ether (HFPME) was found to dissolve both FDC and fluorinated polyimide (FPI) based on a systematic study using a phase diagram, achieving a homogeneous disperse phase for emulsification composed of oxygen-permeable FPI and oxygen-soluble FDC. Using this novel cosolvent system and Shirasu porous glass (SPG) membrane emulsification, FDC-encapsulated FPI shell microparticles were successfully prepared for the first time. In addition to oxygenation, demonstrated using hypoxia-responsive HeLa cells, the fabricated core-shell microparticles exhibited monodispersity, excellent stability, biocompatibility, and oxygen capacity.

Versatile morphology transition of nano-assemblies via ultrasonics/microwave assisted aqueous polymerization-induced self-assembly based on host–guest interaction

Nano-assemblies have wide applications in biomedicine, functional coatings, Pickering emulsifiers, hydrogels, and so forth. The preparation of assemblies mainly utilizes the polymerization-induced self-assembly (PISA) method, which can produce high-concentration nanoscale assemblies in one step. However, the initiation processes of most reported PISA are limited to thermal initiation. Here, we reported two green and efficient methods for synthesizing nano-assemblies with various morphologies using ultrasound (20 kHz)/ microwave (500 W) assisted aqueous-phase RAFT-PISA in 3 h and 1 h. Cyclodextrin (CD) and styrene (St) nucleating monomer were complexed in a 1:1 ratio. Then, using Poly (ethylene glycol) methyl ether as the macromolecular reversible addition-fragmentation chain transfer (RAFT) agent (PEG-CTA) to control the CD/St complexes, the conversion rate of St monomer was respectively 27 %–60 %, 20 %–30 % within 3 h and 1 h under ultrasonics/microwave assisted PISA. Results showed that the morphologies of the assemblies are not only related to the length of PS block, but also to the assistance types and the remaining monomer concentration. The results showed that only PEG45-b-PS90 and PEG45-b-PS241 assemblies prepared by ultrasonics assisted PISA form evolved lamellaes and vesicles (100 nm), which break through the limitation of kinetic freezing. But the ultrasonic reaction on morphology of assemblies is not all favourable. For one thing, it can promote the movement of particles; for another, it makes reverse morphology transformation and sphere is preferred morphology. Therefore, the main reason of morphology evolution is the remaining monomer concentration of PEG45-b-PS90 and PEG45-b-PS241 assemblies reaches to 55 %–65 %, which promoting the segment movement. The results showed that the morphology of the assemblies prepared by microwave assisted PISA changed from spherical micelles to short rods, and finally to vesicles (120–140 nm) as the length of hydrophobic PS block increases. The kinetic freezing problem was solved in microwave-assisted PISA due to the action of microwaves and more remaining monomer concentration. Both them can boost particles movement.