Mixture Of Methyl Esters Research Articles

Multicomponent Synthesis of C(8)-Substituted Purine Building Blocks of Peptide Nucleic Acids from Prebiotic Compounds.

We have explored the reaction of a three-components mixture of aminomalononitrile, urea and α-amino acid methyl esters for the multicomponent synthesis substituted purines resembling PNA's building blocks. 2,6-diamino-purines, 6-amino-3,9-dihydro-2H-purin-2-one (iso-guanines), and 3,9-dihydro-6H-purin-6-one derivatives, selectively decorated at C(8)-position of the purine ring with different amino acid residues, were obtained from acceptable to good yields. The regio-selectivity of the transformation was controlled by the use of urea in the ternary mixture and by the annulation agent involved in the ring-closure of amino-imidazole carbonitrile intermediates. Solvent free conditions, microwave irradiation and simple one-carbon containing reagents further satisfied the major requirement of atom economy and sustainable chemistry. Due to the prebiotic nature of the three-components mixture and of annulation agents, it also embodies the possibility for the synthesis of novel PNAs bearing purine nucleobases decorated at C(8)-position of the imidazole ring as alternative RNA analogues in molecular evolution.

Tandem hydroformylation-amine condensation and reduction of canola fatty acid methyl esters for production of diesel renewable antioxidant additives

A canola fatty acid methyl esters (FAME) mixture was synthesized through transesterification and modified by rhodium homogeneous tandem hydroformylation-amine condensation, with primary amines, yielding imine products. The obtained imines were reduced by maceration with sodium borohydride and alumina, yielding secondary amine products. The synthesized fatty imines and amines were evaluated as additives for commercial diesel and biodiesel on concentrations of 0.5 and 1.0 %, while tested for oxidative stability fallowing the EN14112 standard method. The tested amino products exhibited higher oxidative stability, which justifies its application as antioxidant additives, while the diesel blends did not show expressive physicochemical modifications. The modified amino-FAME antioxidant performance, justifies a renewable biorefinery application, extend the biodiesel shelf-life prior to diesel blending, complies with UN’s Sustainable Development Goals (SDGs) and if prepared from residues, enhance the circular economy appeal.

Machine Learning for Characterizing Biofuels Based on Femtosecond Laser Ionization Mass Spectrometry.

A sample mixture of fatty acid methyl esters (FAMEs) was measured by femtosecond laser ionization mass spectrometry (fsLIMS) using the fifth (206 nm) and fourth (257 nm) harmonic emissions of an ytterbium (Yb) laser (1030 nm). Molecular ions were observed as the major signals in this technique, providing valuable information concerning the molecular weight and the number of double bonds in the molecule. The mass spectral data were then used as explanatory variables in machine learning based on artificial intelligence (AI) to correlate with objective variables such as the cetane number, kinematic viscosity, specific gravity, a higher heating value, an iodine value, flash point, oxidative stability index, and a cloud point measured for reference biofuel samples containing various FAMEs. The properties of biofuels, i.e., the objective variables, were evaluated from the mass spectral data obtained for unknown samples. The errors in the evaluation were a few percent when the distribution of the FAMEs in the unknown biofuel sample was similar to those of the biofuels used for machine learning. As demonstrated herein, the present approach, involving a combination of fsLIMS and AI, has the potential for use in evaluating the properties of a biofuel and then in solving of environmental issues associated with global warming.

Revisiting the Potential of Group VI Inorganic Precatalysts for the Ethenolysis of Fatty Acids through a Mechanochemical Approach.

The utilization of biobased feedstocks to prepare useful compounds is a pivotal trend in current chemical research. Among a varied portfolio of naturally available starting materials, fatty acids are abundant, versatile substrates with multiple applications. In this context, the ethenolysis of unsaturated fatty acid esters such as methyl oleate is an atom-economical way to prepare functional C10 olefins with a biobased footprint. Despite the existence of a variety of metathesis catalysts for the latter process, there is a lack of readily available, efficient, and inexpensive catalytic systems based on earth-abundant metals (Mo, W) whose preparation does not require sophisticated syntheses and manipulations. Here, a systematic exploration of homogeneous and heterogeneous inorganic Mo, W (oxy)halides shows that MoOCl4, while inactive as a homogeneous species, forms active and selective silica-supported ethenolysis precatalysts able to reach equilibrium conversion of methyl oleate within a few minutes upon activation with SnMe4. Such heterogeneous MoOCl4-based precatalysts were easily accessed through mechanochemical solvent-free procedures and found to contain, upon characterization by elemental analysis and Raman spectroscopy, isolated (≡SiO)Mo(=O)Cl3 units or polymeric silica-supported [-O(≡SiO)nMoCl4-nO-]m (n = 1, 2) complexes depending on the molybdenum loading. The former isolated species exhibited a higher catalytic performance. The developed heterogeneous precatalysts could be applied to the ethenolysis of various substrates, including polyunsaturated fatty acid esters and industrial fatty acid methyl ester (FAME) mixtures from palm oil transesterification.

Corrosion Induced on Aluminum by Biodiesel Components in Non-Oxygen Environments.

Biodiesel is a mixture of saturated and unsaturated Fatty Acid Methyl Esters (FAMEs) whose composition affects the corrosion behavior of metal containers during storage. This study examines the effect of the C=C bond present in selected FAMEs (Methyl Stearate, Methyl Oleate, and Methyl Linoleate) in aluminum corrosion in the absence of oxygen. First, mass loss assays were carried out at 100, 200, and 280 °C for 1000 h using pure Methyl Stearate (MS), 5% Methyl Oleate in Methyl Stearate (MS-5% MO), and 5% Methyl Linoleate in Methyl Stearate (MS-5% ML). Next, chemical changes in FAMEs were studied using FTIR, TGA, and GC/MS. SEM/EDS analysis allowed us to inspect the aluminum surfaces and their chemical characterization. We estimated higher corrosion rates for MS assays than those of unsaturated methyl ester mixtures. In a separate set of experiments, we used electrochemical techniques (potentiodynamic polarization, linear polarization resistance, and electrochemical impedance spectroscopy) to investigate aluminum corrosion induced by thermal-degraded products from FAMEs at 100, 200, and 280 °C for 300 h able to dissolve in aqueous extracts. These electrochemical experiments revealed that the products in the aqueous extracts from the unsaturated methyl ester mixture form a passive layer on the Al surface thicker than pure MS at the corresponding degradation temperatures.

Sodium Methoxide Catalyzed Preparation of Nitrogen Compounds from Palm Oil Methyl Esters as Corrosion Inhibitor

This research was conducted to study preparation of nitrogen compounds by reacting palm oil derived methyl esters and diethanolamine using sodium methoxide as a catalyst. The chemical composition of the product was analyzed using the gas chromatography-mass spectrometry (GC-MS) method. The product was then applied as a corrosion inhibitor for mild steel in CO2 saturated 3% NaCl solution. Experimental results indicate that the reaction product contains six nitrogen compounds with a relative percentage of 63.7%, and the rest 36.7% are a mixture of unreacted diethanolamine and unreacted methyl esters. The results of the corrosion experiments show that the product obtained exhibited appreciably high performance as reflected by a percentage of protection (%P) of 96.85%. The performance of the product as a corrosion inhibitor is also supported by the SEM image of the mild steel sample, which shows that the surface of the sample is well protected. The results of this work demonstrate that nitrogen compounds obtained have promising potential as corrosion inhibitors, particularly to prevent corrosion by CO2 gas.

Recycled waste groundnut oil: A potential feedstock for green energy/biodiesel synthesis

This work focuses on the recycling of waste groundnut oil as a potential feedstock for biodiesel production using activated coconut husk as a regenerating agent. The coconut husk was functionalized using organic acid. The properties of the functionalized coconut husk were investigated via instrumental analysis. Non-parametric modeling involving 2-degree isotherm models were used. The regeneration/recycling of the waste oil were done in batch mode examining key factors of temperature, time, concentration and dosage. Biodiesel was synthesized from recycled waste groundnut oil using transesterification reaction. The properties of biodiesel were examined using ASTM and AOAC official standards. Brunauer-Emmett-Teller surface analysis revealed the surface area of the adsorbent as 371.88 m2/g and a porosity distribution of 0.567 η on the surface at a pH of 6.1. Batch mode analysis revealed that 97.5% of impurities was removed from waste groundnut oil under one batch process at 80 °C after 4 h with 6 g of the activated coconut husk. Langmuir isotherm model provided the best fit to the experimental data with adsorption capacity of 33.5 mg/g at R2 of 0.996. Adsorption of waste groundnut oil impurities onto activated coconut husk was endothermic, as evidenced by the calculated ΔH of +2.7914 kJ/mol. A high cetane number of 48.4 obtained after transesterification is an indication of the good ignition quality of the obtained recycled waste groundnut oil methyl ester. Kinematic viscosity and acid value were revealed to be 4.65 mm2 S−1 and 0.31 mg KOH/g, while the calorific value stood at 38,053 kJ/kg. GC-MS analysis revealed a complex mixture of fatty acid methyl esters dominated by unsaturated fatty acids (58.78%). Recycling of waste cooking oil in this work using activated coconut husk demonstrated good quality as a regenerating agent. The properties of biodiesel obtained showed that it has all the good qualities comparable to other existing biodiesel based on the ASTM and AOAC official standards. More work on the recycling of other waste cooking oils for green energy synthesis to protect our environment from pollution emanating from the use of conventional petro-diesel and promote energy transition is highly recommended.

Assessment of the functioning of biofuel-powered engines based on a multi-criteria analysis

Reducing the emission of exhaust gas components into the natural environment from the transport sector is a priority. In recent years, the European Union has published many legal acts that regulate the emission of exhaust gas components. One of the known ways to reduce them is to use alternative fuels to power combustion engines. The paper presents an assessment of the functioning of drive units powered by mixtures of diesel oil and fatty acid methyl esters. The AHP (analytic hierarchy process) method was used for the analysis, which made it possible to determine the values of individual assessments. Based on the analysis, it was found that the lowest exhaust emission parameters were obtained for a fuel mixture containing 30% fatty acid methyl esters.

An overview of biodiesel, a fuel blend made from palm oil.

With the increasing global demand and rising fossil fuel prices, the oil industry is turning to alternative fuels from renewable sources like biodiesel or vegetable oils. To compensate for the scarcity of fossil fuels, fuel from vegetable oils is one of the alternatives to meet energy needs. Biodiesel is considered a suitable and better choice due to its environmentally friendly features, reduced carbon dioxide emissions, and functional properties similar to fossil fuels. The diesel blend is a renewable fuel derived from a mixture of hydrocarbons (diesel) and fatty acid methyl esters (FAME). This article focuses on biodiesel produced in Indonesia from palm oil as a feedstock for biofuel production. As one of the world’s largest palm oil producers, the production of biodiesel in Indonesia, especially biodiesel from palm oil, has many advantages and disadvantages in terms of economic, social and economic aspects. environment. Use specifically as a fuel is sometimes problematic because biodiesel is hygroscopic and can corrode steel. The scope of this study is based on a brief overview of the progress and challenges in developing palm oil biodiesel feedstock to pursue in the future.

Content of fatty acids in lipids of adipose derived mesenchymal stem cells

The content of fatty acids in the lipids of mesenchymal stem cells of dog adipose tissue culture was studied. Mesenchymal stem cells of dog adipose tissue culture were obtained by culturing the primary material in a CO2 incubator with a content of 5 % CO2, at a temperature of 37 °C in DMEM medium with the addition of 10–15 % fetal bovine serum and 1 % antibiotic-antimycotic. When the confluency of the monolayer reached 70–80 %, the cells were transferred to a suspension and subcultivated in order to reduce the heterogeneity of the culture and obtain a sufficient amount of biological material. The lipids of the obtained stem cells were analyzed for the content of fatty acids by the method of thin-layer gas-liquid chromatography. Determination of the content of lipids of fatty acids in FSK of a cat was carried out by the Folch method. A mixture of fatty acid methyl esters was analyzed on a Trace GC Ultra gas chromatograph with a flame ionization detector on a capillary column SPTM –2560, 100 m x 0.25 mm ID, 0.20 μm film (Supelco). Identification of fatty acids was carried out using a standard sample of Supelco 37 Сomponent FAME Mix. Quantitative assessment of the LC spectrum was carried out by the method of normalization of the peak planes of methylated LC derivatives and their content was determined as a percentage of the total content of all LC. The conducted study of the content of fatty acids in lipids made it possible to reveal certain features of the lipid metabolism of mesenchymal stem cells cultured in dog adipose tissue. A high content of oleic acid, characteristic of cells resistant to apoptosis and with high proliferative potential, was determined; a high ratio of unsaturated linoleic to saturated stearic acid (С18:1/С18.0), which reflects the high activity of the stearoyl-coenzyme-desaturase enzyme and, indirectly, the active state of the Wnt/β-catenin signaling pathway; inability to lengthen the chain of saturated fatty acids; lack or low activity of de novo synthesis of omega-6 polyunsaturated fatty acids. 18 fatty acids were found in the composition of lipids of fetal stem cells of a cat, of the saturated ones - the most palmitic acid (33.70 ± 0.02 %), of the monounsaturated ones – oleic acid (21.63 ± 0.03 %), of the polyunsaturated ones – linoleic acid (6.45 ± 0.07 %). The least amount of cis-,11,14-eicosadienoic acid (0.04 ± 0.01 %) was found in the composition of cell lipids. The total amount of saturated fatty acids in dog mesenchymal stem cell lipids was 65.65 ± 0.02 %), unsaturated fatty acids – 34.35 ± 0.02 %. Monoene fatty acids were determined in the amount of 24.46 ± 0.02 %, and polyene – 9.89 ± 0.02 %. The ratio index of polyunsaturated fatty acids ω 3 to ω 6 is 0.40. Lipids of mesenchymal stem cells of adipose tissue culture were characterized by a lower content of monoene unsaturated fatty acids 24.46 ± 0.02; (P < 0.05), with a higher content of ω3 fatty acids 3.04 ± 0.02 %; (P < 0.05), with a lower content of ω6 fatty acids 6.86 ± 0.02 %; (P < 0.05) in contrast to lipids of red bone marrow stem cells.

Experimental analysis of a diesel engine run on non-conventional fuel blend at different preheating temperatures

Due to urbanisation, the reuse of scrap tyres in the form of energy has gained attention for the disposal of waste tyres. Among the numerous methods, pyrolysis appears to be possible, appealing and viable for generating products such as pyrolysis oil, which can be combined with petroleum oils and used as a source of energy. In a prior study, a mixture of jatropha methyl ester (JME) and tyre pyrolysis oil (TPO) was used as a diesel engine fuel, and it was discovered that the JMETPO20 (JME80% + TPO20%) blend gave better results among all the test blends but inferior than diesel operation. Also, it was reported that due to higher viscosity of the JMETPO20 blend, engine gave inferior performance than diesel operated engine. In this context, an attempt has been made to utilize the JMETPO20 blend at different preheating temperatures to substitute conventional diesel. The blend was preheated at three different temperatures, that is, 50, 60 and 70°C and experiments were carried out in a single-cylinder diesel engine with a rated output of 4.4 kW. The results of the investigations were analysed and compared with diesel and presented in this study.

A comprehensive two-scale model for predicting the oxidizability of fatty acid methyl ester mixtures

The intricate mechanisms of oil thermooxidation and their accurate prediction have long been hampered by the combinatory nature of propagation and termination reactions involving randomly generated radicals. To unravel this complexity, we suggest a two-scale mechanistic description that connects the chemical functions (scale 1) with the molecular carriers of these functions (scale 2). Our method underscores the importance of accounting for cross-reactions between radicals in order to fully comprehend the reactivities in blends. We rigorously tested and validated the proposed two-scale scheme on binary and ternary mixtures of fatty acid methyl esters (FAMEs), yielding three key insights: (1) The abstraction of labile protons hinges on the carrier, defying the conventional focus on hydroperoxyl radical types. (2) Termination reactions between radicals adhere to the geometric mean law, exhibiting symmetric collision ratios. (3) The decomposition of hydroperoxides emerges as a monomolecular process above 80 °C, challenging the established combinatorial paradigm. Applicable across a wide temperature range (80 °C to 200 °C), our findings unlock the production of blends with controlled thermooxidation stability, optimizing the use of vegetable oils across applications: food science, biofuels, and lubricants.

Optimizing the subcritical water valorization of insect (Hermetia illucens l.) farming waste for biodiesel production

To counter the proliferation of secondary waste streams generated on insect (black soldier fly) farms, the present study integrated green water technology and acid-catalyzed transesterification as a basis to assess further value extraction potentials. By valorizing the waste streams, a process was developed to promote the circular economy paradigm. In this regard, wastes generated from a local insect farm were initially subjected to subcritical water extraction (SWE) for lipid recovery. The SWE process was optimized such that an enhanced lipid yield of 13.31 wt% was obtained at temperature, time, and solid loading conditions of 236.8 °C, 10 min of extraction, and 1 g/ 100 mL respectively. The lipids recovered were then subjected to an acid-catalyzed transesterification reaction for the production of a fatty acid methyl ester (FAME) mixture. A preliminary economic assessment of the process was also undertaken. The results showed that the wastes had the potential to be economically employed in the production of biodiesel that satisfied fuel property standards. In addition, the potential of employing the side streams as an animal feed was also highlighted due to the determined dominance of oligopeptides, which are known for their favorable bioactive properties. The results indicated that insect farming waste is a promising renewable source for high-quality biodiesel and animal feed production through the environmentally friendly biorefinery.

Environmentally Friendly New Catalyst Using Waste Alkaline Solution from Aluminum Production for the Synthesis of Biodiesel in Aqueous Medium.

Red mud (RM) is composed of a waste alkaline solution (pH = 13.3) obtained from the production of alumina. It contains high concentrations of hematite (Fe2O3), goethite (FeOOH), gibbsite [Al(OH)3], a boehmite (AlOOH), anatase (Tetragonal-TiO2), rutile (Ditetragonal dipyramidal-TiO2), hydrogarnets [Ca3Al2(SiO4)3-x(OH)4x], quartz (SiO2), and perovskite (CaTiO3). It was shown to be an excellent catalytic mixture for biodiesel production. To demonstrate the value of RM, an environmentally friendly process of transesterification in aqueous medium using waste cooking oil (WCO), MeOH, and waste alkaline solution (WAS) obtained from aluminum production was proposed. Triglycerides of WCO reacted with MeOH at 60 °C to yield mixtures of fatty acid methyl esters (FAMEs) in the presence of 0.019% (w/w) WAS/WCO using the WAS (0.204 mol L-1, predetermined by potentiometric titration) from aluminum production by the Bayer process. The use of the new catalyst (WAS) resulted in a high yield of the products (greater than 99% yield).

Stability of B50 biodiesel added with glycerol ester additive based on palm oil oleic acid

Biodiesel in Indonesia is a mixture of Fatty Acid Methyl Ester (FAME) and diesel oil. Mixing FAME and diesel oil is challenging since FAME is separated from diesel oil at low temperatures. Changes in the physico-chemical properties of biodiesel during storage decrease biodiesel quality due to dissolved oxygen, potentially damaging the engine. Using glycerol ester (GE) as an additive can be an alternative solution to tackle that problem. This research examined the stability of GE-added biodiesel. As a comparison, commercial diethyl ether (DEE) additive was used. The concentration of additive added to biodiesel varied at 1000, 2000, and 3000 ppm while the storage temperature varied at 12, 25, and 42℃. The stability of biodiesel was evaluated for three months by measuring the acid value, viscosity, corrosion rate, and water content. The acid values ​​​​of the various types and concentrations of additives still meet the SNI 7182-2015 standard (0.5 mg KOH g-1 sample) with a value range of 0.148- 0.392 mg KOH g-1 sample. Kinematic viscosity had a value range of 3.12-3.58 cst, which also meets the SNI 7182-2015 standard (2.3-6 cst). The highest corrosion rate for GE and DEE was in the first week, with values of 0.447 and 0.261 mpy, respectively. Both B50 biodiesel control and the addition of 1000 ppm GE had the same water content value on the 18th day, which was 0.046%, and this value was considered the highest water content. This means adding an additive can maintain the water content in B50 biodiesel. Overall, GE additives in B50 biodiesel with various concentrations comply with SNI 7182-2015 standard.

Testing and Analysis of Selected Operating Parameters of a Vehicle Powered by Fuel with the Addition of Biocomponents

The most common fuel used for powering compression ignition engines is diesel, whose main components are petroleum products. The constantly growing energy demand involves the implementation of new technical solutions and applying alternative fuels, including renewable ones, such as rapeseed oil, sunflower oil, peanut oil, and animal fats. The most commonly used biofuels are those obtained from chemically processed rapeseeds (transesterification) to provide them with physical–chemical properties similar to diesel fuel. The study presents the results of tests of a power unit fueled with different mixtures of diesel oil and fatty acid methyl esters. The experiment was carried out for a compression ignition engine of 81 kW power with direct fuel injection. Performance parameters of the vehicle power unit and its computer software were modified for the needs of the tests. Those modifications involved increasing the fuel dose and the fuel injection pressure. The test results were statistically analyzed. Based on the results, a simulation of power and torque was performed, depending on the vehicle computer system adjustment and the fuel mixture used. A simulation of the vehicle movement in a non-homogeneous environment (variable road conditions) was performed concerning the vehicle motion kinematics. The simulations were carried out in a V-SIM 5.0 program. The simulation was performed at five speeds, respectively: 0 km/h, 25 km/h, 50 km/h, 75 km/h, and 100 km/h. The simulation made it possible to determine speed, acceleration, time, and distance. The analysis shows that the highest acceleration of 3 m/s2 was obtained for the BIO50 mixture, regulation V. The longest road section needed to achieve the maximum speed (100 km/h) was recorded for the BIO10 mixture, regulation II. The simulation duration ranged from 17.9 s to 17.74 s, depending on the adopted variant.

Analysis of the noise emission generated by a drive unit powered by mixtures of diesel oil and fatty acid methyl ester

The sound generated by drive units is one of the aspects that are addressed in sustainable transport development strategies. The regulations of the European Union, which indicate the ecological aspect of the use of internal combustion engines as one of the most important, also refer to the level of sound emission generated by these engines. The use of alternative fuels to power combustion engines allows not only to reduce the toxic components of exhaust gases, but also to reduce the noise they generate during operation. The manuscript presents the study of a drive unit powered by mixtures of diesel oil and fatty acid methyl esters, in which the software regulations of the control system were modified. Studies have shown a decrease in the level of sound emission when powered by alternative fuels.

RAPID METHOD FOR SIMULTANEOUS DETERMINATION OF CIS-9, TRANS-11 AND TRANS-10, CIS-12 CONJUGATED LINOLEIC ACID ISOMERS IN MILK BY GC-FID

Ruminant milk is the lead source of conjugated linoleic acid (CLA) in the human diet, with cis-9, trans-11 CLA being the major among all. Small amounts of trans-10, cis-12 CLA are also found in synthetic supplements. Since both isomers are biologically active with potential health benefits, there is great interest in quantifying them for quality control routines. An alternative method for the analysis of the aforementioned CLAs by fast gas chromatography (GC) is discussed in the present study. The fatty acid methyl ester mixture obtained by alkaline catalysis was injected into a GC equipped with a flame ionization detector (FID) and fitted with an ionic liquid SLB-IL111 chromatographic column (15 m × 0.10 mm × 0.08 µm). Separation was achieved in less than 5 min using a 168 °C isotherm run. Both CLA isomers were quantified by using of single point standard addition statistical approach. Results were contested to those obtained using the recommended 100 m long CP-Sil88 capillary column and none evidence of significant differences was found within 95% confidence interval. Therefore, the proposed method could be valuable to focused regulatory routines of large numbers of samples with greater analytical frequency.

Synergistic effect in co-processing a residue from a transesterification process with vacuum gas oil in fluid catalytic cracking

• Co-processing of bio-oil in existing fluid catalytic cracking unit produces biofuel. • Bio-oil oxygen content determines its blends level with vacuum gas oil or VGO. • Distillation residue from biodiesel production using waste fats and oil is used. • Synergistic effect of bio-oil and VGO shows yield of gasoline higher than predicted. • Cracking of 10 wt% bio-oil has the closest coke characteristics compared to VGO. The catalytic co-processing of bottom fuel oil (BFO) with refinery vacuum gas oil (VGO) using a commercial fluid catalytic cracking (FCC) zeolite equilibrium catalyst was carried out to ascertain its potential as a source for biofuels. The BFO used was the distillation residue from biodiesel transesterification process using waste fats and oil; being a mixture of saturated and unsaturated fatty acid methyl esters. The catalytic cracking experiments were performed in a laboratory fixed bed micro activity test (MAT) reactor at 516 °C and atmospheric pressure. As well as the VGO and BFO, three different blends were used with BFO to VGO mass ratios of 10:90, 20:80 and 50:50, and catalyst-to-oil (C/O) ratios of 3.0 – 5.7. The synergistic effect of BFO in VGO blends includes the yield of gasoline, and LPG being higher than predicted for the blends of 10 wt% BFO in VGO. Also, the formation of more CO 2 with the increase in BFO blend level suggests CO 2 production through decarboxylation reactions as a possible route. The compositions of the produced gasoline for pure VGO and 10 wt% BFO are similar as well. The cracking of 10 wt% BFO gives a higher fraction of aromatics, alkenes and naphthenes than other blends. However, some deterioration was observed when higher substitution levels of BFO were used, resulting in a decrease in the gasoline yield and higher yields of LCO, HCO and coke as predicted. Overall, co-processing BFO with VGO may be economically attractive because the BFO is obtained from waste oils and fats which are one of the under-exploited sources of biodiesel feedstocks and add value to waste management.

Lemon seed oil: An alternative source for the production of glycerol‐free biodiesel

AbstractThe aim of this study was the evaluation of two different procedures for the one‐pot transformation of oil extracted from Citrus limon seeds to a mixture of fatty acid methyl esters (FAMEs) and glycerol derivatives for application as a potential biofuel. Lemon seed oil was obtained by Soxhlet extraction. The first procedure was realized by efficient irreversible transesterification of the oil in hexane by lipase B from Candida antarctica (Novozym 435®) using dimethyl carbonate as the alcohol donor. For the realization of the second methodology an acid‐catalyzed transformation was carried out, dissolving the seed oil in methyl tert‐butyl ether in a microwave tube using Amberlyst®‐36 dry form catalyst. Both procedures, in optimized conditions, led to the complete conversion of the triglycerides to give the corresponding FAMEs and a mixture of glycerol derivatives. The absence of free glycerol in the final mixtures makes the two herein described procedures considerably advantageous in terms of both cost and sustainability since they enable performance of the production of FAMEs without requiring steps to remove glycerol. These final mixtures may be used in the energy chain and exploited as biofuels. © 2022 The Authors. Biofuels, Bioproducts and Biorefining published by Society of Industrial Chemistry and John Wiley & Sons, Ltd.