Metres Research Articles

Multivariate process capability analysis for evaluating metal additive manufacturing via electron beam melting

Abstract Electron beam melting (EBM) as one of the relatively new metal AM techniques showed promising and increasing applications. Therefore, there is a need to evaluate the quality of the EBM process using its critical quality characteristics. However, EBM and different AM process parts have many functionally or statistically correlated quality characteristics. Consequently, the quality characteristics of the EBM process should be evaluated together. Therefore, this research aims to evaluate the quality of the EBM process using a multivariate process capability index (MPCI). In this study, the dimensional accuracy in different directions is considered as a quality characteristics. The proposed methodology involves producing a large sample of small specimens of square shape using EBM technology. Three critical dimensions of the specimen in the X, Y, and Z axis are investigated as quality characteristics. The dimensions of quality characteristics are measured using a precise measurement device. The normality and stability assumptions of the collected data are investigated using skewness measure, and multivariate process control chart respectively. Then a large sample of the multivariate normal data is simulated using computer software to estimate the percent of nonconforming (PNC) from the established specification limits, which is used to estimate MPCI. Finally, the capable tolerance of the process is estimated and the sensitivity analysis of variation is investigated. The results show the capability of the EBM process under different specification limits designations. Estimating MPCI revealed that the EBM process is capable under very coarse limits only. Moreover, the sensitivity analysis showed that variation in quality characteristics data is very sensitive for MPCI estimation, especially variation in width quality characteristic.

Association Between Tongue Pressure and Prevalence of Mild Cognitive Impairment in Japan.

Although it has been suggested that a decline in oral function is one of the potential risk factors affecting mild cognitive impairment (MCI), evidence is insufficient to draw clear conclusions. This Japanese cross-sectional study examined the association between tongue pressure (TP) and MCI in middle-aged and older adults aged 36-84years. Study participants were 1019 (368 men and 651 women). TP was evaluated using a TP measurement device. The maximum value of three measurements was used for analysis. MCI was defined as being present if a participant had a Japanese version of the Montreal Cognitive Assessment score of <26. Adjustment was made for age, smoking status, alcohol consumption, leisure-time physical activity, body mass index, hypertension, dyslipidemia, diabetes mellitus, history of depression, number of teeth, employment, education, and household income. The prevalence of MCI was 45.3%. Among women, compared with the lowest tertile of TP, the second and highest tertiles were significantly associated with a lower prevalence of MCI with a clear dose-response relationship; the adjusted odds ratio (95% confidence intervals) in the second and highest tertiles of TP were 0.54 (0.36-0.83) and 0.55 (0.36-0.84), respectively (p for trend=0.005). In contrast, no statistically significant association was observed between TP and the prevalence of MCI among men. Our findings suggest that higher TP might be inversely associated with the prevalence of MCI in middle-aged and older Japanese women.

Automatic characterization of capillary flow profile of liquid samples on μTADs based on capacitance measurement

Capillary flow profile of liquid samples in porous media is closely related to the important properties of liquid samples, including the viscosity and the surface energy. Therefore, capillary flow profile can be used as an index to differentiate liquid samples with different properties. Fast and automatic characterization of capillary flow profile of liquid samples is necessary. In this work, we develop a portable and economical capacitance acquisition system (CASY) to easily obtain the capillary flow profile of liquid samples on microfluidic thread-based analytical devices (μTADs) by measuring the capacitance during the capillary flow. At first, we validate the accuracy of this method by comparing with the traditional method by video analysis in obtaining the capillary flow profiles in μTADs of cotton threads or glass fiber threads. Then we use it to differentiate liquid samples with different viscosity (mixture of water and glycerol). In addition, capillary flow profile on μTADs with chemical valves (chitosan or sucrose) can also be obtained on this device. Lastly, we show the potential of this device in measurement of hematocrit (HCT) of whole blood samples. This device can be used to catalog liquid biological samples with different properties in point-of-care diagnostics in the near future.

Open, Active-Controlled Clinical Study to Evaluate the Correlation between Whole Body DEXA and BIA Muscle Measurements.

Dual energy X-ray absorptiometry (DXA) is the gold standard for diagnosing sarcopenia. However, comparative studies using bioelectrical impedance analysis (BIA) would be required in the Korean population. This study aimed to evaluate the correlation between total-body bone density measuring devices (Hologic and GE Lunar) and a bioelectrical impedance measurement device (InBody 970) as well as the correlation between upper body muscle mass. A total of 119 participants were involved in this study, aged 20 to 70 years, with specific body mass index ranges and no severe health conditions used both DXA (or DEXA) and BIA technologies to assess body composition. The participants were scanned using a Hologic QDR-4500W DXA scanner and GE-Lunar Prodigy DXA systems, and the InBody 970 type of multi-frequency BIA machine. Statistical analysis was performed to determine the correlation between the devices, with a coefficient of at least 0.8. The muscle mass measurement comparisons between the InBody 970 and Hologic devices demonstrated remarkably high correlation coefficients (exceeding 0.9) across all limbs. Similarly, the muscle mass comparison between the Inbody 970 and GE Lunar devices also revealed substantial correlation coefficients, ranging from 0.83 upwards, across all limbs. Limb muscle mass measurements using Hologic and GE Lunar whole-body DXA and Inbody 970 BIA demonstrated particularly high levels of concordance. In addition, a conversion formula that bridges limb muscle mass measurements from two widely used whole-body DXA machines and a BIA machine will facilitate sarcopenia research and patient management.

An Improved Laplace Satellite Tracking Method Based on the Kalman Filter

When photoelectric measuring equipment is used to track satellites, the extraction of the short-term or long-term target often fails because the target is weak, clouds block the target, and/or the sun’s angle is too small, resulting in the loss of the tracking target. In this study, an improved Laplacian satellite tracking method based on the Kalman filter is proposed. Firstly, the improved Laplacian algorithm was used for the initial fitting of the equation of motion of a small amount of measurement data. Judgment of the validity and Kalman filtering was carried out on the current frame’s measurement data to calculate the optimal estimate of the current frame’s orbit data, and the accurate equation of motion was iteratively fitted to obtain high-precision data for predicting the satellite’s orbit frame by frame. Numerical tracking of the equipment was carried out. This method was experimentally validated on an actual optical measurement device. The test results showed that this method can make up for the frequent loss of short-term targets. Under the condition that the maximum deviation is less than 3”, the length of extrapolated data can be up to 30 s and the length of the measurement data was less than 30 s. This method may improve the stability of tracking equipment as well as the accuracy and integrity of the measurement data.

Development of a wireless multichannel miniature impedance measurement system and its application for bolt loosening detection

The piezoelectric impedance-based technique is always regarded as one of the most promising structural health monitoring and nondestructive evaluation methods. In recent years, impedance measurement chip AD5933 with the characteristics of high integration and cost-effectiveness makes it possible to address the huge and high-cost problems of the commercialized impedance measurement instrument during the process of structural health monitoring and defect identification. However, it still faces lots of challenges for the chips to be utilized in practical applications due to several limitations, such as short distance for data transmission, single measurement channel and artificial attendant requirement. In this paper, a wireless multichannel miniature impedance measurement system composed by the front-end measurement device and the remote measurement and control platform on the server, is firstly developed and presented with the functions of wireless data transmission, multi-channel acquisition and remote data post-processing. Subsequently, the design concept and composition of the system were introduced in detail. Then, a series of piezoelectric transducers related tests were conducted to validate its impedance measurement performance, especially when comparing with the ones measured by commercialized instruments. In addition, to verify its effectiveness and feasibility of the developed system for the structural damage detection, a bolt loosening detection experiment on the flange connection of a pipeline specimen was investigated for its damage localization and severity quantification. Finally, all the results demonstrated that the developed system provides a great possibility to be used as a convenient and portable impedance measurement tool for the civil structural health monitoring and damage identification in practical applications.

Systematic Evaluation of Isometric Maximal Muscle Strength in an Orthopaedic Cohort.

Although the lower extremities are essential for movement function and human gait, no normalized isometric maximum strength values, which include the factors gender, age, weight, height, and body mass index (BMI), have been defined to date for orthopaedic patients. To systematically analyze the isometric maximal muscle strength of a cohort in an orthopaedic outpatient clinic and to evaluate its relation to gender, age, weight, height, BMI, and the differences between diseases. Cross-sectional study. Level 4. Isometric maximal muscle strength of knee extension, knee flexion, hip abduction, and hip adduction was measured in orthopaedic patients of an outpatient clinic using a specific muscle strength measurement device. Correlation analysis was performed for age, gender, height, weight, and BMI. Patients were grouped by disease characteristics. The cohort consisted of 311 subjects (sex: 164 male, 147 female; age: 48.63 years, SD = 16.595; BMI: 26.56 kg/m², SD = 4.9). Age correlated significantly with maximal isometric muscle strength. At the age of 54 years onward, based on 133 patients, a decline in maximum isometric muscle strength was detected. Gender showed a strong influence on maximal isometric muscle strength, with significantly higher values for male patients. Furthermore, weight and height, but not BMI, correlated significantly with muscle strength. For clinical studies comparing different evidence-based training interventions for rehabilitation, it is important to consider determinants such as gender, age, weight, and height for isometric maximum strength measurement. For further validation, follow-up examinations taking into account the performance level, other target groups, and other muscle groups are required to avoid the wide dispersion of isometric maximum strength values. These results and associated determinants are highly clinically relevant and can be used as a reference for further studies in the field of musculoskeletal regeneration.

Construction of SuperKEKB vacuum control system and its eight years operation experience

SuperKEKB has two main rings (MRs), namely low- and high-energy rings, with circumferences of 3 km; beam transport (BT) lines; and a positron damping ring (PDR). We upgraded the MRs and BT line vacuum control systems and designed a new PDR vacuum control system for upgrading KEKB to SuperKEKB.Here, we describe the basic configuration of the vacuum control system, which includes the interlock logic (gate valve open/closed control, non-evaporable getter pump activation, and beam abortion). We subsequently present the collimator driving system and the cooling water control system for the beam pipe of the final focusing superconducting quadrupole magnet as examples of special SuperKEKB vacuum control systems. Examples of problems in the SuperKEKB vacuum control system, including the discharge at the high-voltage connector of the ion pump, stoppage of the cooling water pump for the vacuum system, and failure of the collimator position measurement device are described.

面向小粒蔬菜种子的气吸排种器排种性能试验

Vegetable precision planting agronomy is suitable for my country's current vegetable planting system, and the air-suction vegetable precision planter is currently the most important work tool in my country. This paper designs a kind of air-absorbing vegetable precision sower for the problems of small vegetable seeds with small grains, poor mobility and high difficulty in achieving uniform sowing of small seeds. First, Fluent software is used to simulate and analyze the flow field of the air chamber in the seed metering device, and the pressure and velocity of the fluid in the air chamber are analyzed. Through the comparison of the pressure distribution cloud chart and the velocity distribution cloud chart, the influence of different apertures, holes, vacuum degree, and gas chamber depth on the flow field of the gas chamber is analyzed. The air suction seed discharger test bench was set up and orthogonal test was carried out, and the test results showed that the optimal parameter combination was 3.5 kPa vacuum degree of the air chamber, 2.4 mm diameter of the type hole, and 18 r/min rotational speed of the seed discharging disk. The high-speed photographic test was carried out under the optimal parameter combination, and the results showed that leakage of suction, adsorption of 1 seed, and adsorption of multiple seeds appeared in the process of suction, and it is important for the development of the air suction precision machine for small seeded vegetables with better performance. The results showed that the phenomenon of leakage, adsorption of 1 seed and adsorption of multiple seeds occurred in the process of seed suction, which provided a reference basis for the development of a better performance of the air-absorption precision planter for small seeds.

Methodology and Monitoring of the Strengthening and Upgrading of a Four-Story Building with an Open Ground Floor in a Seismic Region

Many buildings around the world fail to meet current earthquake resistance requirements and have significant potential to be a risk to human life and property. Therefore, a seismic upgrade of such buildings is quite necessary. Over the past decades, hundreds of buildings have been strengthened and upgraded to improve their seismic resistance, and thousands more are planned for years to come. In Israel, this was followed by National Outline Plan No. 38, which provides a basis for retrofitting and adding new areas to existing buildings. It should be noted that adding new floors to existing buildings increases seismic forces. Moreover, structure material properties change over a building’s lifetime, which should be also considered for strengthening. The proposed research investigates and validates the existing practice for strengthening and upgrading buildings in seismic regions and suggests ways of improving their efficiency. Experiments and numerical analysis were performed on a real existing residential building that requires strengthening and upgrading. A corresponding methodology was proposed for monitoring the strengthening and upgrading processes, including selecting measurement devices and their real use. Using sensors with the highest sensitivity enabled measurements of micro-vibrations and investigations of the recorded signal to obtain the building’s natural vibration frequencies. Experimental measurements allowed us to distinguish different frequencies of the building at all strengthening and upgrading stages. The measured dynamic parameters of the building allowed a more accurate calculation of seismic forces for all of these stages and consequently made the design more effective. Therefore, we recommended monitoring buildings in each stage of seismic strengthening and upgrading.

Calibration methods for high frequencies: Development and validation

The paper presents an introduction of an advanced method for calibration of high-frequency instruments, such as oscilloscopes, frequency counters and function generators that operate at the frequencies between 1 MHz and GHz range. Based on conducted thorough survey of the needs for calibration of high-frequency measurement devices in the region of Southeast Europe, and the identified calibration and measurement capability gap in comparison to the international metrology offer, the Laboratory for Electrical Measurements at Ss. Cyril and Methodius University in Skopje developed new methods, following the general recommendations of the EURAMET cg-7 Calibration Guide. An original approach in the design of the experimental procedure, and a novel data fusion concept for the evaluation of the measurement uncertainty is deployed. The paper also investigates and resolves some challenges of setting up an unbroken measurement traceability chain, and uncertainty estimation for calibration in the domain of high frequencies. The established and accredited calibration capabilities are essential for the region of Southeast Europe, where the metrology facilities for the calibration/testing of high frequency electronic devices are inadequate to meet the conformity assessment needs of the quickly growing automotive supply chain sector, and the needs of other electrical and electronic industries.

Design and Validation of a Monte Carlo Method for the Implementation of Noninvasive Wearable Devices for HbA1c Estimation Considering the Skin Effect.

To diagnose diabetes early or to maintain stable blood glucose levels in diabetics, blood glucose levels should be frequently checked. However, the only way to check blood glucose levels regularly is to use invasive methods, such as pricking the fingertip or using a minimally invasive patch. These invasive methods pose several problems, including being painful and potentially causing secondary infections. This study focuses on noninvasively measuring glycated hemoglobin (HbA1c) using PPG signals. In particular, the study relates to a method and a hardware design technology for removing noise that may be present in a PPG signal due to skin contact with a noninvasive HbA1c measurement device. The proposed HbA1c measurement device consists of the first sensor (PPG sensor) module including an optical barrier and the second sensor (cylindrical sensor) module for removing the skin effect. We have developed a Monte Carlo method to implement accurate, noninvasive HbA1c measurement by considering different skin properties among different subjects. Implementing this model in wearable devices will allow end users to not only monitor their glycated hemoglobin levels but also control diabetes with higher accuracy without needing any blood samples. This will be a groundbreaking advancement in modern wearable medical devices.

Microfluidic paper-based analytical device for measurement of pH using as sensor red cabbage anthocyanins and gum arabic

The objective of this study was to develop and validate a novel microfluidic paper-based analytical device (μPADpH) for determining the pH levels in foods. Anthocyanins from red cabbage aqueous extract (RCAE) were used as its analytical sensor. Whatman No. 1 filter paper was the most suitable for the device due to its porosity and fiber organization, which allows for maximum color intensity and minimal color heterogeneity of the RCAE in the detection zone of the μPADpH. To ensure the color stability of the RCAE for commercial use of the μPADpH, gum arabic was added. The geometric design of the μPADpH, including the channel length and separation zone diameter, was systematically optimized using colored food. The validation showed that the μPADpH did not differ from the pH meter when analyzing natural foods. However, certain additives in processed foods were found to increase the pH values.

An Introduction to Ventra: A Programmable Abdominal Phantom for Training, Educational, Research, and Development Purposes.

Intra-abdominal pressure (IAP) is a critical parameter in the care of critically ill patients, as elevated IAP can lead to reduced cardiac output and organ perfusion, potentially resulting in multiple organ dysfunction and failure. The current gold standard for measuring IAP is an indirect technique via the bladder. According to the Abdominal Compartment Society's Guidelines, new measurement methods/devices for IAP must be validated against the gold standard. This study introduces Ventra, an abdominal phantom designed to simulate different IAP levels, abdominal compliance, respiration-related IAP variations, and bladder dynamics. Ventra aims to facilitate the development and validation of new IAP measurement devices while reducing reliance on animal and cadaveric studies. Additionally, it offers potential applications in training and education for biomedical engineering students. This study provides a thorough explanation on the phantom's design and fabrication, which provides a low-cost solution for advancing IAP measurement research and education. The design concept, technical aspects, and a series of validation experiments determining whether Ventra is a suitable tool for future research are presented in this study. Ventra's performance was evaluated through a series of validation tests using a pressure gauge and two intra-gastric (Spiegelberg and CiMON) and two intra-bladder (Accuryn and TraumaGuard) pressure measurement devices. The mean and standard deviation of IAP recordings by each device were investigated. Bland-Altman analysis was used to evaluate bias, precision, limits of agreement, and percentage error for each system. Concordance analysis was performed to assess the ability of Ventra in tracking IAP changes. The phantom demonstrated excellent agreement with reference pressure measurements, showing an average bias of 0.11 ± 0.49 mmHg. A concordance coefficient of 100% was observed for the phantom as well. Ventra accurately simulated different abdominal compliances, with higher IAP values resulting in lower compliance. Abdominal volume changes showed a bias of 0.08 ± 0.07 L/min, and bladder fill volume measurements showed an average difference of 0.90 ± 4.33 mL for volumes ranging from 50 to 500 mL. The validation results were in agreement with the research guidelines of the world abdominal society. Ventra is a reliable tool that will facilitate the development and validation of new IAP measurement devices. It is an effective educational tool for biomedical engineering students as well.

Unsupervised online poor contact detection in the secondary circuit of voltage transformers

Voltage transformers (VTs) are fundamental and crucial instrument devices for accurate voltage measurement. Generally, measurement errors can be caused by both the VT and the secondary circuit. Most research focused on the VT but ignored the secondary circuit between it and the measurement device. Poor contact in the secondary circuit is more challenging to capture than those caused by faulty VTs. In this study, we present an unsupervised online poor contact detection method. It first exploits a time series similarity matrix derived from the measured voltage data. The physical constraints deriving from the electrical topology are utilized to eliminate the non-fault fluctuation. To ensure the versatility of the proposed method, an adaptive threshold determination strategy is designed based on knee point location. Numerical experiments compared with some state-of-the-art methods have validated the effectiveness of the proposed method. The versatility of the proposed method is further validated in three real-world cases.

Deep Entropy-Learning based virtual inertia control for VRFB regulation considering Phase-Locked loop dynamics

The virtual inertia control (VIC) technique is often adopted as a prominent mechanism to address the inertia deficiency of modern integrated power systems with high penetration of sustainable energy units. In such control mechanisms, a phase-locked loop (PLL) is required to estimate the grid frequency. However, utilization of such frequency measurement platforms is accompanied by large frequency fluctuations due to its inherent dynamics. In particular, this paper proposes an adaptive integral recursive backstepping (I-RBSC) based on virtual inertia for the regulation of vanadium redox flow battery (VRFB) in stand-alone Micro-Grids (SMGs). Unlike previous works that neglected the effect of frequency measurement devices, this work investigates the effect of PLL dynamics in virtual inertia control. The I-RBSC controller is designed by an entropy-driven actor-critic neural networks (NNs) to adaptively adjust the tunable coefficients during its interaction with the SMG. By training the ability of deep NNs, the entropy is maximized to regulate the system output. The VRFB unit can be discharged up to 90% which can quickly respond to the randomness of loads and sustainable energy units. The transient outcomes of SMG reveal the feasibility of I-RBSC (designed by entropy learning) to address the challenges of low inertia and PLL dynamics. The real-data of wind turbine and solar radiation are utilized to simulate the SMG in a more realistic framework from a systematic point of view. The comprehensive analysis under typical scenarios confirms the supremacy of the suggested VIC controller over prevalent state-of-the-art virtual inertia controllers including conventional VIC, fuzzy logic, backstepping, and model-predictive control (MPC).

Assessing the contribution of different upper limb degrees of freedom to an unconstrained shoulder proprioception task

For the purpose of testing shoulder joint proprioception while controlling for axioscapular muscle recruitment, a novel shoulder thoracohumeral (TH) rotation joint position sense (JPS) measurement device was designed. This device was intended to measure shoulder TH rotation, while also implicitly constraining other upper limb degrees of freedom (DOF) and minimizing cutaneous sensation. The purpose of this study was to determine whether joint motion aside from shoulder TH rotation is being captured by the shoulder JPS measurement device. Upper limb kinematics were collected from 32 participants during joint angle matching trials using the shoulder JPS measurement device. Step wise multiple regression revealed that shoulder TH rotation (β-Humeral Rotation = 0.409, p < 0.001), and wrist deviation (β-Wrist Deviation = 0.104, p = 0.008) both contributed a significant unique variance in the prediction of shoulder JPS measurement device rotation. Findings suggest that seated, unconstrained shoulder TH rotation JPS testing protocols in literature may be confounded by contributions from joints both proximal and distal to the shoulder. Researchers should be aware of the limitations of both constrained and unconstrained shoulder TH rotation JPS testing protocols.

Development of automatic arc sag measurement equipment for tensioned line tightening construction on overhead transmission lines

Due to the low degree of automation of the existing arc droop measurement device, the tension line digital twin system is not yet able to simulate the change of arc droop in the actual engineering situation in a high degree of real time. To this end, a kind of arc droop automatic measuring equipment applicable to the working condition of tension frame line tightening construction is developed. In terms of hardware, firstly, the STC microcontroller is used to control the motor to achieve free movement of the equipment on the wire. Secondly, the Beidou positioning module is used to collect the spatial coordinates of each point on the wire, thereby obtaining the spatial attitude of the wire and calculating the final sag. Finally, LoRa technology with long transmission distance and low power consumption is selected for wireless transmission of controlled data and collected data. The software system of the device is equipped with the motor's action logic, which cooperates with the hardware to respond to the control commands issued by the terminal. The developed arc droop measurement equipment has been successfully applied in the project, compared with the traditional arc droop observation construction method construction efficiency increased by 28%, the difference between the observation file arc droop and the design arc droop after erection of the line is 1.96%. Digital simulation and remote guidance of arc sag variations by the digital twin system for tension racking lines was realized while ensuring the engineering requirements.

Quasi-static cyclic tests of FRP-confined steel-reinforced HPFRCC circular columns

This study presents a novel composite component comprising of steel-reinforced high-performance fiber reinforced cementitious composites (HPFRCC) circular columns confined by fiber-reinforced polymer (FRP), with the goal of improving the mechanical behavior of conventional reinforced concrete (RC) columns. Quasi-static cyclic loading tests were conducted to investigate various aspects of the column specimens, including failure phenomena, load-displacement response, sectional compression-bending performance, plastic hinge length, and lateral strain distributions in the FRP jacket, etc. A self-designed frictional force measurement device was employed to accurately measure the actual force borne by the specimen. The experiment results revealed that FRP confinement effectively improved the load-bearing capacity and deformation capacity of the specimens and delayed the deterioration of the sectional compression-bending performance. The superior tensile ductility of HPFRCC led to increased yielding displacement and peak load compared to FRP-confined concrete specimen, although this enhancement was limited. Furthermore, the peak load of the FRP-confined HPFRCC specimen increased with axial load, while the sectional compression-bending performance after the peak load remained relatively stable until approaching the collapse prevention (CP) limit state.

Thermo-economic analysis and comparison of novel desiccant air conditioning systems

Desiccant air conditioning (DAC) systems are considered an effective alternative to traditional vapor compression systems due to their ability to independently control temperature and humidity, coupled with their environmentally friendly design. Consequently, this paper deals with experimental and simulation study on DAC systems. The experiments were conducted on a reference system (RS) equipped with all necessary control and measurement devices. This reference system includes a traditional desiccant evaporative air-conditioning system with an additional heat exchanger placed after the desiccant wheel, functioning as an after-cooler. In addition, steady state and transient simulation models were developed using TRNSYS software to predict the performance of four different configurations of DAC systems and the reference system, under hot and humid climatic conditions.The experimental data verify the precision and relevance of the simulation results, with an average error of 2.57 % for the air temperatures. The steady state findings showed that Config-4 exhibited the best thermal performance compared to the other configurations. Also, Config-4 demonstrates a stable thermal cooling capacity despite fluctuations in outdoor air dry-bulb temperature. Transient results revealed that, Config-4 has levelized costs of CO2 emissions that are 64.2 % lower than RS, followed by Config-3, Config-2, and Config-1. Lower CO2 emissions result in a positive impact on mitigating climate change and improving air quality. Economic analysis revealed that the total levelized cost of cooling (LCOC) for Config-4 is 70.5 % lower than RS, demonstrating the most significant cost reduction. Configurations 3, 2, and 1 also showed lower LCOC compared to the reference system.