Oxide Research Articles

Conversion of 5‐hydroxymethylfurfural and carbohydrates to 2,5‐diformylfuran over supported Mo‐based catalysts

Here, a series of nitrogen‐doped carbon (NC) supported transition metal oxide catalysts were prepared by pyrolysis of chitosan‐metal salt mixtures for the efficient synthesis 2,5‐diformylfuran (DFF) from 5‐hydroxymethylfurfural (HMF) and fructose. Among them, supported molybdenum‐based species on nitrogen‐doped carbon (Mo/NC) exhibited excellent activity and selectivity for selective oxidation of HMF to DFF. The presence of nitrogen species reduces the electron cloud density around the Mo species, thereby improving the catalytic activity. Moreover, the interaction between active MoO2 species on the catalyst surface and NC ensured the stability of the catalyst, resulting in no significant loss of activity after four catalytic cycles. 99.5% and 55.1% yields of DFF with full conversion were obtained from HMF and fructose respectively over Mo/NC‐chitosan‐600 in DMSO under ambient air. In order to enhance DFF yield from fructose, sulfonate groups were introduced into Mo/NC‐chitosan‐600 catalyst, leading to the highest DFF yield of 70.2%. In addition, this catalyst also allowed 10.0%, 22.9% and 33.3% DFF yields from glucose, sucrose and inulin, respectively.

Application of a Scaled‐up Dielectric Barrier Discharge Reactor in the Trace Oxygen Removal in Hydrogen‐Rich Gas Mixtures at Ambient and Elevated Pressure

AbstractDielectric barrier discharges (DBDs) are frequently utilized in various gas conversion processes. For industrial applications a low flow resistance and scalability are crucial. In this study a tenfold scaled‐up reactor based on a surface dielectric barrier discharge (SDBD) was employed for the removal of oxygen traces from H2/N2/O2 gas mixtures. The conversion efficiency of the reactor with ten electrode configurations was investigated for different admixtures of O2, and high degrees of conversion were observed that decreased with increasing flow rate, but remained constant when raising the pressure to 2 bar(g). A new generator based on silicon carbide field‐effect transistors (SiC‐FETs) was used and compared to a generator based on classical metal oxide semiconductor field‐effect transistors (MOS‐FETs).

Photon-assisted electron depopulation of 4H-SiC/SiO2 interface states in n-channel 4H-SiC metal–oxide–semiconductor field effect transistors

4H-SiC/SiO2 interface states play a major role in the performance and reliability of modern 4H-SiC metal–oxide–semiconductor field effect transistors (MOSFETs). To gain new insights into these interface states, we developed a cryogenic measurement technique that uses photon-assisted electron depopulation to probe device performance limiting 4H-SiC/SiO2 interface states. This technique enables the characterization of shallow as well as deep states at the 4H-SiC/SiO2 interface of fully processed devices using a cryogenic probe station. Our method is performed on n-channel 4H-SiC MOSFET test structures with deposited oxide and postoxidation anneal. We identify conditions under which the electrons remain trapped at 4H-SiC/SiO2 interface states and trigger the controlled photon-assisted electron depopulation within a range of photon energies. This allows us to prove the presence of near interface traps, which have previously been found in thermally grown 4H-SiC MOS structures. Our results are supported by device simulations. Additionally, we study the impact of irradiation intensity and light exposure time on the photon-induced processes.

Enhanced photocatalytic performance of bi-doped TiO2 under sunlight and UV light: mechanistic insights and comparative analysis.

Bismuth-doped metal oxides exhibit favourable photocatalytic features when exposed to both sunlight and UV light. In this approach, Bi0/TiO2 and Bi+3/TiO2 photocatalysts were prepared and their structural and optical properties are analysed using various characterization techniques. These developed photocatalysts were further tested for the photocatalytic elimination of Nitrobenzene in UV light and sunlight and compared with the performance of bare TiO2. The catalyst Bi+3/TiO2 performed better in UV light with 72.31% degradation, and 4.74 × 10-6mol.litre-1.min-1 initial rate of reaction. However, when exposed to sunlight, Bi0/TiO2 outperformed with 73.85% degradation, and 4.63 × 10-6mol.min-1 initial rate of reaction. This significant increase in photocatalytic activity of Bi0/TiO2 under sunlight could be accredited to increased light harvesting and enhanced efficiency in charge carrier separation, both of which were made possible by bismuth-induced surface plasmon resonance.

Naphthalene Diimide-Modified SnO2 Enabling Low-Temperature Processing for Efficient ITO-Free Flexible Perovskite Solar Cells.

A low-cost and indium-tin-oxide (ITO)-free electrode-based flexible perovskite solar cell (PSC) that can be fabricated by roll-to-roll processing shall be developed for successful commercialization. High processing temperatures present a challenge for the PSC fabrication on flexible substrates. The most efficient planar n-i-p PSC structures, which utilize a metal oxide as an electron transport layer (ETL), necessitate high annealing temperatures. In addition, the device performance deteriorates owing to the migration of halogen ions, which causes the oxidation of the metal electrodes. These drawbacks conflict with the development of highly efficient flexible PSCs fabricated on ITO-free transparent electrodes. Herein, an efficient ETL material that enables low-temperature processing is presented. Tin dioxide (SnO2) is modified by (sulfobetaine-N,N-dimethylamino)propyl naphthalene diimide (NDI-B) and used as an ETL. The NDI-B effectively reduces the interfacial nonradiative recombination between the ETL and perovskite and suppresses the ion migration by passivating oxygen-vacancy defects in SnO2 and strongly interacting with halogen ions, respectively. Based on the NDI-B-blended SnO2 ETL, a record PCE of 17.48% is achieved in the ITO-free flexible PSC fabricated at low temperature.

Influence of metal and metal oxide nanoparticles on growth and total phenolic content accumulation of Anoectochilus roxburghii cultured in vitro

The application of metal nanoparticles in agriculture and related fields, especially in plant cell tissue culture has increased interest in recent years due to its potential benefits. This study used gold nanoparticles (AuNPs), silver nanoparticles (AgNPs), copper nanoparticles (CuNPs) and magnetite nanoparticles (Fe3O4NPs) to evaluate their effect on the growth and total phenolic content (TPC) of Anoectochilus roxburghii. The results showed that Fe3O4 NPs were the most positively influenced metal nanoparticles in increasing biomass and TPC of A. roxburghii among metal nanoparticles tested. After 8 weeks of culture, the dry weight (DW) and TPC of the plants cultured on the medium containing 5 ppm Fe3O4NPs were 39.07 mg and 13.0 mg gallic acid respectively per g of dry weight (mg GAE/g DW). Meanwhile, on the medium without Fe3O4NPs, they were 30.47 mg and 6.71 mg GAE/g DW respectively. This study proposed an effective approach to improve the growth and accumulation of TPC in A. roxburghii. Moreover, it suggests the potential application of metal nanoparticles in plant tissue culture and the production of bioactive compounds.

In situ grazing incidence synchrotron x-ray diffraction studies on the wakeup effect in ferroelectric Hf0.5Zr0.5O2 thin films

The discovery of ferroelectricity in HfO2 ultrathin films has gathered considerable interest from the microelectronic industry owing to their compatibility with complementary metal oxide semiconductor technology. However, a significant challenge in utilizing HfO2 thin films for commercial devices is the wakeup effect, which is an increase in polarization with the number of electric field cycles in HfO2-based capacitors. Despite efforts to develop wakeup-free HfO2 thin films, the root cause of this effect remains elusive. Some studies attribute it to the tetragonal (T) to orthorhombic (O) phase transformation, while others suggest it is due to the redistribution of oxygen vacancies within the HfO2 layer during electric field cycling. This study investigated the phase transformation dynamics and oxygen vacancy distributions in TiN/Hf0.5Zr0.5O2/TiN capacitors subjected to electric field cycling using in situ grazing incidence synchrotron x-ray diffraction and ex situ x-ray photoelectron spectroscopy. The as-grown HZO films were crystallized in a mixed phase consisting of monoclinic (M), tetragonal, and orthorhombic fractions. The T-phase volume fraction decreased continuously up to 10k electric field cycles. In contrast, the O-phase fraction increased within the first 100 cycles and then stabilized with further cycling. The redistribution of oxygen vacancies occurred continuously throughout the cycling process. The results revealed that continuous oxygen vacancy redistribution during electric field cycling resulted in phase transformation between the T-, O-, and M-phases. The study provides insight into the phase transformation dynamics and oxygen vacancy redistribution in TiN/Hf0.5Zr0.5O2/TiN capacitors during electric field cycling, shedding light on the underlying mechanisms of the wakeup effect.

Using Mössbauer Spectroscopy to Evaluate the Influence of Heat Treatment on the Surface Characteristics of Additive Manufactured 316L Stainless Steel

The oxidation behaviour of iron-based 316L stainless steel was investigated in the temperature range of 700 to 1000 °C. The test specimens in the shape of plates were produced by selective laser melting. After fabrication, the samples were sandblasted and then annealed in air for different periods of time (0.5, 2, 8, 32 h). Under the influence of temperature and time, stainless steels tend to form an oxide layer. Scanning electron microscopy, energy dispersive analysis, and X-ray diffraction were employed to analyse the composition of this layer. Notably, a thin oxide layer primarily composed of (Fe-Cr) formed on the surface due to temperature effects. In addition, with increasing temperature (up to 1000 °C), the oxide of the main alloying elements, specifically Mn2(Fe-Cr)O4, appeared alongside the Fe-Cr oxide. Furthermore, the samples were subjected to conversion X-ray (CXMS) and conversion electron (CEMS) Mössbauer spectroscopy. CXMS revealed a singlet with a decreasing Mössbauer effect based on the surface metal oxide thickness. CEMS revealed the presence of Fe3+ in the surface layer (0.3 µm). Moreover, an interesting phenomenon occurred at higher temperature levels due to the inhomogeneously thick surface metal oxide layer and the tangential direction of the Mössbauer radiation towards the electron detector.

Synthesis of Metallic and Metal Oxide Nanoparticles Using Homopolymers as Solid Templates: Luminescent Properties of the Eu+3 Nanoparticle Products

Starting from poly(4-vinylpyridine) ((P4VP)n), poly(2-vinylpyridine) ((P2VP)n), and [N=P(O2CH2CF3)]m-b-P2VP20 block copolymers, a series of metal-containing homopolymers, (P4VP)n⊕MXm, (P2VP)n⊕MXm, and [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm MXm = PtCl2, ZnCl2, and Eu(NO3)3, have been successfully prepared by using a direct and simple solution methodology. Solid-state pyrolysis of the prepared metal-containing polymeric precursors led to the formation of a variety of different metallic and metal oxide nanoparticles (Pt, ZnO, Eu2O3, and EuPO4) depending on the composition and nature of the polymeric template precursor. Thus, whereas Eu2O3 nanostructures were obtained from europium-containing homopolymers ((P4VP)n⊕MXm and (P2VP)n⊕MXm), EuPO4 nanostructures were achieved using phosphorus-containing block copolymer precursors, [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm with MXm = Eu(NO3)3. Importantly, and although both Eu2O3 and EuPO4 nanostructures exhibited a strong luminescence emission, these were strongly influenced by the nature and composition of the macromolecular metal-containing polymer template. Thus, for P2VP europium-containing homopolymers ((P4VP)n⊕MXm and (P2VP)n⊕MXm), the highest emission intensity corresponded to the lowest-molecular-weight homopolymer template, [P4VP(Eu(NO3)3]6000, whereas the opposite behavior was observed when block copolymer precursors, [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm MXm= Eu(NO3)3, were used (highest emission intensity corresponded to [N=P(O2CH2CF3)]100-b-[P2VP(Eu(NO3)3)x]20). The intensity ratio of the emission transitions: 5D0 → 7F2/5D0 → 7F1, suggested a different symmetry around the Eu3+ ions depending on the nature of the polymeric precursor, which also influenced the sizes of the prepared Pt°, ZnO, Eu2O3, and EuPO4 nanostructures.

An experimental study on jute/banana fiber reinforced poly(vinyl alcohol) composites with nanofiller

AbstractThe incorporation of nanoparticles into natural fiber composites has the potential to alter the characteristics of natural fiber composites. In this study, various properties of jute and banana fiber reinforced poly(vinyl alcohol) (PVA) composites with different nanofillers incorporation were investigated. Samples were prepared using the vacuum bagging technique. Inorganic nanoparticles (Al2O3, ZnO, MgO, CuO, and TiO2) were synthesized using a ball milling machine and in each sample, 3 wt.% of nanofillers were incorporated. The maximum ultimate tensile strength and elongation percentage is found for TiO2, which is 90.433% higher than pure PVA whereas MgO incorporated samples provides maximum flexural strength, which is 162.59% higher than PVA. The sample with Al2O3 provides strongest impact resistance, 17.3 J/cm2. It was found that the decomposition temperatures were slightly higher for MgO and CuO doping than the undoped PVA composite. The FT‐IR spectra exhibited notable hydroxyl groups and minor shifts indicating a reduction in hydrophilicity upon the introduction of nanoparticles. The water absorption exhibited a reduction of up to 36% in conjunction with an increase in density across all samples. The highest crystallinity is found for CuO nanofiller composite, validated by x‐ray diffraction analysis. Additionally, morphological changes in the composites were seen through scanning electron microscopy and EDX shows a strong peak at 2.1 keV indicate some impurities present in the samples.Highlights Jute/banana/PVA composites were prepared with 3 wt% nanoparticles incorporation. Metal oxides such as Al2O3, ZnO, MgO, CuO, and TiO2 were used as nanoparticle. The use of nanoparticle improved the tensile, flexural, and impact properties. Decomposition temperatures were found higher for MgO and CuO incorporated composites. Upon nanoparticle incorporation, water absorption exhibited a reduction of upto 36%.

A Novel Electronic Nose Using Biomimetic Spiking Neural Network for Mixed Gas Recognition

Odors existing in natural environment are typically mixtures of a large variety of chemical compounds in specific proportions. It is a challenging task for an electronic nose to recognize the gas mixtures. Most current research is based on the overall response of sensors and uses relatively simple datasets, which cannot be used for complex mixtures or rapid monitoring scenarios. In this study, a novel electronic nose (E-nose) using a spiking neural network (SNN) model was proposed for the detection and recognition of gas mixtures. The electronic nose integrates six commercial metal oxide sensors for automated gas acquisition. SNN with a simple three-layer structure was introduced to extract transient dynamic information and estimate concentration rapidly. Then, a dataset of mixed gases with different orders of magnitude was established by the E-nose to verify the model’s performance. Additionally, random forests and the decision tree regression model were used for comparison with the SNN-based model. Results show that the model utilizes the dynamic characteristics of the sensors, achieving smaller mean squared error (MSE < 0.01) and mean absolute error (MAE) with less data compared to random forest and decision tree algorithms. In conclusion, the electronic nose system combined with the bionic model shows a high performance in identifying gas mixtures, which has a great potential to be used for indoor air quality monitoring in practical applications.

Surprising Effects of Ti and Al2O3 Coatings on Tribocatalytic Degradation of Organic Dyes by GaN Nanoparticles

GaN is more stable than most metal oxide semiconductors for the photocatalytic degradation of organic pollutants in harsh conditions, while its catalytic efficiency has been difficult to be substantially improved. In this study, the tribocatalytic degradation of organic dyes by GaN nanoparticles has been investigated. Stimulated through magnetic stirring using homemade Teflon magnetic rotary disks in glass beakers, the GaN nanoparticles were found to induce negligible degradation in rhodamine B (RhB) and methyl orange (MO) solutions. Surprisingly, the degradation was greatly enhanced in beakers with Ti and Al2O3 coatings on their bottoms: 99.2% and 99.8% of the 20 mg/L RhB solutions were degraded in 3 h for the Ti and Al2O3 coatings, respectively, and 56% and 60.2% of the 20 mg/L MO solutions were degraded in 24 h for the Ti and Al2O3 coatings, respectively. Moreover, the MO molecules were only broken into smaller organic molecules for the Ti coating, while they were completely degraded for the Al2O3 coating. These findings are important for the catalytic degradation of organic pollutants by GaN in harsh environments and for achieving a better understanding of tribocatalysis as well.

CO2‐Hydrogenation to Methanol over CuO/ZnO Based Infiltration Composite Catalyst Spheres

Multiple active component catalysts for efficient conversion of CO2 to Methanol (MeOH) are synthesized through coating γ‐Al2O3 carrier spheres by incipient wetness impregnation method (IWI). The well‐known bimetallic Copper Oxide/Zinc Oxide (CuO/ZnO) are promoted in three steps, first by Cerium Oxide (CeO2), then additionally with Zirconium Oxide (ZrO2) and finally with Calcium Oxide (CaO) resulting in four carrier catalysts with high surface area and catalyst pore. Quaternary and quinary carrier catalysts promoted with moderate CeO2, ZrO2 in the quaternary (20% CZCZ) and additionally with CaO (20% CZCZC) in the quinary catalysts demonstrate high CO2‐conversion ratios (16.2% and 18.7%) and space time yields (0.51 and 0.47 gMeOH h‐1 gCatalyst‐1) at 5 MPa and 250 °C reactor temperature. The high conversion ratios (XCO2) and good methanol space‐time‐yields (STYMeOH) are attributed to enhanced copper dispersion and several multi metal oxide component interactions essential to enhance CO2‐activation and ‐conversion through the catalytic systems as well as very high overall surface area. Compared to related studies, the carrier catalysts show superior conversion rates, proving the effectiveness of the introduced multi‐component carrier catalyst and extending the understanding of infiltrate composites as possible large‐scale application alternatives to precipitated MeOH catalyst systems.

Three-dimensional pine-tree-like bimetallic sulfide with maximally exposed active sites by secondary structural restructuring for efficient electrocatalytic OER

Developing efficient, low-cost and bifunctional catalysts with predominant durability for the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) is an extraordinary challenge in the preparation of green hydrogen energy by electrochemical water splitting. Three-dimensional (3D) transition metal compounds have become a research hotspot as OER electrocatalysts, which can replace noble metal oxides such as RuO2 and IrO2 to reduce application costs. Herein, we synthesized a novel three-dimensional pine-tree-like bimetallic sulfide arrays on nickel foam (FeCoS/NF) using various optimization strategies such as morphology optimization, in situ growth and introduction of heterogeneous structures. The as-synthesized FeCoS/NF electrocatalyst only requires relatively low overpotential of 156 mV to achieve a current density of 20 mA cm−2 for OER, with a Tafel slope of only 37 mV dec−1. It also has a small charge transfer resistance, an electrochemical surface area and good electrochemical stability in alkaline electrolytes. The excellent performance of FeCoS/NF can be attributed to the synergistic effect and amorphous phase of FeCoS as well as the well-defined pine-tree-like array architecture with a large surface area, abundant active sites, and sufficient gas and electrolyte diffusion channels.

Optical, physical, mechanical, structural, and radiation shielding investigations of B2O3–TeO2-GeO2-MgO-PbO for ionizing protection and optical transmission application

This study aims to investigate a new heavy glass system's potential use in the radiation shielding and optical transmission applications. Glass former like borate is replaced in this work by heavy metal oxides like lead oxide in the following glass system: (35-x) B2O3–20TeO2-10GeO2-35MgO-xPbO (where x = 2.5, 5, 7.5, and 10 mol%). Through the melt-annealing process, four transparent glasses were synthesized. A number of physical properties were reported, namely the boron–boron separation x 10−8 m, field strength x 1018 (cm2), inter nuclear distance x 10−8 m, ion concentration (N) x 1023 (ion cm3), molar volume (cm3/mol), molecular weight (g/mol), and polaron radius x 10−9 m. Moreover, the following mechanical and structural properties of the synthesized glasses were explored: bulk modulus (B, GPa), dissociation energy (kcal/cm3), fractal bond connectivity (d), longitudinal modulus (L, GPa), hardness (H, GPa), oxygen packing density, packing density (Vt), oxygen molar volume, packing factor (Vi), shear modulus (S, GPa), Poisson radius (σ), and Young modulus (Y, GPa). To study the bulk glasses' nature, the X-ray diffraction was examined. Optical absorption along with optical transmission profile have been recorded to extract various optical properties, as well as the direct and indirect band gap. The transmittance spectra of the prepared glass samples' FTIR were investigated within the 400–2000 cm−1 range. This allowed for the examination of molecular structural groups and vibrational modes. Radiation shielding parameters have been calculated and studied using XCOM software and MCNP-5 algorithm.

Nano-innovations in lubrication: Unveiling the synergistic boundary lubrication potential of zinc titanate with phosphonium ionic liquid

This study investigates the potential of Zinctitanate (ZnTiO3) nanoparticles (APS <100 nm) as nano-additives in lubricant formulations, in conjunction with phosphonium phosphate ionic liquids. Comparative analysis against well-established nano-additives highlights ZnTiO3's exceptional dispersion stability, enduring beyond 225 days. Tribological assessments unveil significant enhancements in antiwear, antifriction, and extreme pressure properties, with 1 wt% ZnTiO3 outperforming the base oil. The ZnTiO3 hybrid nanolubricants exhibited notable synergy, achieving a 49 % reduction in wear compared to hexagonal boron nitride (hBN) and Boehmite NPs. Surface characterization confirms the formation of a protective transfer film (≥100 nm thick), attributed to ZnTiO3's disintegration under tribostress. This results in the development of a mixed metallic metal oxide interfacial film composed of (FeTiO3, FePO4, and ZnO) domains on exposed nascent steel surfaces through tribochemical reactions. These findings suggest ZnTiO3 as a promising nano-additive for advanced lubricants, offering substantial improvements in dispersion stability and tribological performance.

Advancements in enzyme-free electrochemical glucose sensor materials

ABSTRACT Increased health awareness has called for better health monitoring devices, resulting in continuous research and advancement in glucose sensors. Innovations in both enzymatic and enzyme-free sensors (or non-enzymatic) are revolutionising diabetes control. While enzymatic sensors offer superior sensitivity and selectivity, enzyme-free sensors are preferred for stability and affordability, advancing the quest for rapid and accurate glucose tests. Progress in the development of enzyme-free glucose sensors is being achieved by improvements in electrode materials as well as sensor design. The selection of electrode materials is crucial in these sensors for attaining optimum values of sensing time as well as accuracy. Numerous electrode materials, including graphene, carbon nanotubes, metal oxides (such as platinum and gold), and conductive polymers, have been developed and studied by researchers to be employed in glucose sensors. Among the most critical factors being considered for developing glucose sensor materials is the selectivity for glucose molecules without interference due to the presence of another molecule. This article focuses on tracing recent developments in enzyme-free glucose sensor research, highlighting efforts to overcome limitations and drive innovation in glucose monitoring technology.

RuNi/TiZr-MMO Catalysts Derived from Zr-Modified NiTi-LDH for CO-Selective Methanation

CO-selective methanation (CO-SMET) is an efficient hydrogen-rich (H2-rich) gas purification technology for proton exchange membrane fuel cells. It is vital to develop suitable catalysts with good low-temperature activity for CO-SMET reactions. In this study, RuNi/TiZrx-mixed metal oxide (RuNi/TiZrx-MMO) catalysts with different molar ratios of Zr/Ti, derived from a Zr-promoted NiTi-layered double hydroxide (NiTi-LDH) precursor were successfully prepared using the co-precipitation and wet impregnation methods. The RuNi/TiZr0.2-MMO catalyst possesses higher catalytic performance in a lower temperature window of 180–280 °C, which can reduce the CO concentration to be below 10 ppm. The characterization results obtained from XRD, BET, SEM, TEM, XPS, TPR, and TPD suggest that the addition of ZrO2 increases the surface area of the catalyst, improves the dispersion of metallic nanoparticles, increases the reducibility of Ni species on the RuNi/TiZr0.2-MMO catalyst’s surface, and enhances the adsorption and activation ability of CO, resulting in remarkable catalytic performance at lower reaction temperatures. Moreover, the RuNi/TiZr0.2-MMO catalyst demonstrated long-term catalytic stability and carbon resistance.

All-Solution-Processed Electronics with Sub-Microscale Resolution and Nanoscale Fidelity Fabricated Via a Humidity-Controlled, Surface Energy-Directed Assembly Process.

Solution-based processes have received considerable attention in the fabrication of electronics and sensors owing to their merits of being low-cost, vacuum-free, and simple in equipment. However, the current solution-based processes either lack patterning capability or have low resolution (tens of micrometers) and low pattern fidelity in terms of line edge roughness (LER, several micrometers). Here, we present a surface energy-directed assembly (SEDA) process to fabricate metal oxide patterns with up to 2 orders of magnitude improvement in resolution (800 nm) and LER (16 nm). Experiment results show that high pattern fidelity can be achieved only at low relative humidities of below 30%. The reason for this phenomenon lies in negligible water condensation on the solution droplet. Employing the SEDA process, all-solution-processed metal oxide thin film transistors (TFTs) are fabricated by using indium oxide as channel layers, indium tin oxide as source/drain electrodes and gate electrodes, and aluminum oxide as gate dielectrics. TFT-based logic gate circuits, including NOT, NOR, NAND, and AND are fabricated as well, demonstrating the applicability of the SEDA process in fabricating large area functional electronics.

Remediation of Sulfides in Produced Waters of the Oil and Gas Industry Using Hydrogen Peroxide

Produced waters are often treated in open lagoons where hydrogen sulfide (H2S) can off gas, posing a risk to human health and the environment. The aim of this study was to optimize a treatment process using hydrogen peroxide (H2O2) to oxidize H2S while minimizing off gassing. Samples of produced water from West Texas and laboratory-prepared waters utilizing sodium sulfide (Na2S) or biogenic polysulfides were oxidized with H2O2 alone or in combination with copper or iron catalysts, sodium hydroxide (NaOH), or a commercial sulfide oxidizer, HydroPower Green™. Sulfur speciation was measured using Hach test kits for sulfide/sulfate/sulfite and Dräger tubes for headspace H2S. HydroPower Green™ (HPG) helped to reduce H2S in the headspace of water samples; some of this was pH related as NaOH also worked, but not as well as HPG. The dose of peroxide necessary to oxidize sulfides to sulfate is a function of the oxidation-reduction potential (Eh) of the water and total sulfide concentration as well as pH; approximately a 1–4:1 ratio of peroxide to sulfide concentration was needed to oxidize sulfidic waters of pH 7–10 with half-lives under 30 min. Both copper and iron catalysts reduce H2O2 demand and the half-life of H2S. Peracetic acid (PAA) and copper (II) sulfate pentahydrate (CuSO4, 5H2O) were explored as biocides for controlling sulfate-reducing bacteria (SRBs) that produce H2S. An AquaSnap (Hygenia) test kit was employed to monitor relative microbial activity in a wetland porewater containing H2S. Microbial regrowth occurred after a few days using the highest dose of PAA; these results showed that PAA was being used by bacteria as a carbon source even after the initial substantial reduction in the microbial activity. CuSO4, 5H2O at a dose of 1 ppm prevented microbial regrowth. The recommended treatment process from this research is determined by jar testing with H2O2, a base for pH control, a biocide, and possibly a metal catalyst or other co-oxidants in order to achieve oxidation of sulfides without H2S release or the precipitation of metal carbonates or oxides.