Metal Layer Research Articles

Exploration of a Novel Electric-Fuse Device with a Simple Structure of Ni Metal on a SiO2 Dielectric for Electrostatic Discharge Protection under a Human Body Model

On-chip electrostatic discharge (ESD) protection poses a challenge in the chip fabrication process. In this study, a novel electric fuse (E-fuse) device featuring a simple structure of Ni metal on a SiO2 dielectric for ESD protection was proposed, and the physical mechanism of its operation was investigated in detail. Experimental evaluations, utilizing transmission line pulse (TLP) testing and fusing performance analyses, reveal that the E-fuse, constructed with a Ni metal layer measuring 5 μm in width, 100 μm in length, and 5 nm in thickness, achieved a significant ESD protection voltage of 251 V (VHBM) and demonstrates low-voltage fusing at a bias voltage of 7 V. Compared to traditional ESD protection devices, the E-fuse boasts a smaller size and removability. To assess fusing performance, devices of varying sizes were tested using a fusing lifetime model. This study supports both theoretical and empirical evidence, enabling the adoption of cost-effective, straightforward E-fuse devices for ESD protection.

A modeling method for thermal steady-state simulation of the four-layer printed circuit board.

Thermal simulation of a Printed Circuit Board (PCB) can help identify potential overheating risks in the circuit. The proposed modeling method combines analytical temperature solutions and numerical approximations. Only Fourier-series analytical solutions related to the prepreg-layer surfaces need to be calculated, rather than the entire structure. Heat transfer through the lateral sides of a PCB is approximately considered as part of the compensated heat flux of the insulating-layer surface boundaries. Heat diffusion within or between metal layers is numerically approximated using the finite volume method. The core layer is treated as "thermally-thick". Temperature-dependent boundary conditions are considered through iterations. A test solver was developed based on the method. The modeling accuracy was validated by comparison with COMSOL Multiphysics for a four-layer structure with a moderate degree of discretization. Additionally, a PCB for generating DC 3.3V was designed, tested, and modeled, with the modeling results confirmed by the thermal images. The electro-thermal analysis of the distribution of electric potential and Joule heating in traces and vias was integrated into the PCB model. The layout maps of the PCB were further adjusted to reduce Joule heating in the output circuit, and the improvement on reducing the IR drop and hotspot temperature was examined.

Phase field thermal shock analysis of rotating porous cracked pretwisted FGM microblade using exact shear correction factor

The present work is an attempt to develop a simple and accurate finite element formulation for the thermal shock analysis of the rotating porous cracked pretwisted functionally graded material (FGM) microblade using modified coupled stress theory in conjunction with phase-field and first-order shear deformation theory (FSDT). The physical neural surface is taken as the reference plane and the exact value of the shear correction factor is calculated from the shear stiffness. The elastic properties are assumed to be temperature-dependent and the upper ceramic layer is subjected to a high thermal shock whereas the bottom metallic layer is maintained at room temperature or is thermally insulated. The governing differential equation for the present analysis is derived using Hamilton’s principle and Newmark average acceleration method is used to obtain the transient response of the rotating porous cracked pretwisted FGM microblade subjected to thermal shock. The results obtained from the present finite element formulation are first validated with several benchmark examples available in the literature. New results are presented investigating the effect of crack depth, crack location, crack angle, rotational velocity and material scale ratio on the transient response of the cracked rotating porous pretwisted FGM microblade subjected to thermal shock. It is shown here that the parameters like crack depth, crack location and crack angle have a significant influence on the transient response of the rotating porous cracked pretwisted FGM microblade.

Metal-only anisotropic impedance holographic metasurface

Abstract This paper presents a kind of metal-only anisotropic impedance holographic metasurfaces (MOAIHMs) made up of periodic wavelength size-variable meta-atoms. The proposed meta-atom has only two metal layers, i.e., a upper patterned layer carved with cylindrical hollows connecting by a narrow metal cuboid, and a lower grounded layer. The two metal layers are separated by an air gap. The anisotropy of this tensor impedance meta-atom can be skillfully realized by simultaneously controlling the radius of cylindrical hollows and the orientation angle of the narrow metal cuboid. The relationship between the geometrical parameters of the meta-atoms arranged in different positions and the impedance strips with alternating light and shade can be directly mapped based on the integration of the holographic theory and the leaky-wave principle. For proof of concept, two MOAIHMs are applied to design linearly polarized broadside pencil beam and dual linearly polarized pencil beams with different radiation angles in the C-band. There is good consistency between the measurements and the simulated results. The satisfactory performance and ultralow profile metal-only structure with reduced fabrication complexity/cost make this proposed design a competitive candidate for space applications.

Ultrathin metal-dielectric planar interface for high-performance photonic spin Hall effect

Abstract This study explores the photonic spin Hall effect (PSHE) with a focus on its sensitivity to incident wave polarization and physical parameter variations. Traditionally surface plasmonic resonance (SPR) systems mainly enhance H-polarized PSHE. However, our proposed method involves an ultrathin metal layer, capped with a glass dielectric layer on a glass substrate, to achieve high-performance PSHE for both H- and V-polarization waves. This high-performance PSHE in terms of enhancement in PSHE magnitudes arises from the simultaneous presence of SPR and waveguiding effects, resulting in the emergence of hybrid TE and TM modes. Investigating Au and Ag ultrathin metal layers, we find that the highest H-polarized PSHE occurs at ~1.52 × 10^6 nm and ~2.05 × 10^5 nm for Au and Ag, respectively. Similarly, for Vpolarized incident light, maximum enhanced PSHE is observed at ~1.58 × 10^5 nm and ~9.48 × 10^4 nm for Au and Ag, respectively. By adjusting the thickness of the metal and/or glass cap layer, precise control over PSHE amplitude and active polarization response is achievable. This research unveils unique capabilities for generating hybrid modes that enhance PSHE for both polarizations, offering a potential platform for developing tunable polarizationfavorable spin optics optoelectronic devices.

Low-resistivity Ohmic contacts of Ti/Al on few-layered 1T'-MoTe2/2H-MoTe2 heterojunctions grown by chemical vapor deposition.

This study explores the phase-controlled growth of few-layered 2H-MoTe2, 1T'-MoTe2, and 2H-/1T'-MoTe2 heterostructures and their impacts on metal contact properties. Cold-wall chemical vapor deposition (CW-CVD) with varying growth rates of MoOx and reaction temperatures with Te vapors enabled the growth of continuous thin films of either 1T'-MoTe2 or 2H-MoTe2 phases on two-inch sapphire substrates. This methodology facilitates the meticulous optimization of chemical vapor deposition (CVD) parameters, enabling the realization of phase-controlled growth of few-layered MoTe2 thin films and their subsequent heterostructures. The study further investigates the influence of a 1T'-MoTe2 intermediate layer on the electrical properties of metal contacts on few-layered 2H-MoTe2. Bi-layer Ti/Al contacts directly deposited on 2H-MoTe2 exhibited Schottky behavior, indicating inefficient carrier transport. However, introducing a few-layered 1T'-MoTe2 intermediate layer between the metal and 2H-MoTe2 layers improved the contact characteristics significantly. The resulting Al/Ti/1T'-MoTe2/2H-MoTe2 contact scheme demonstrates Ohmic behavior with a specific contact resistance of around 1.7 × 10-4 Ω cm2. This substantial improvement is attributed to the high carrier concentration of the 1T'-MoTe2 intermediate layer which could be attributed tentatively to the increased tunneling events across the van der Waals gap and enhancing carrier transport between the metal and 2H-MoTe2.

Achieving Ultra-High-Energy-Density Lithium Batteries: Elimination of Irreversible Anionic Redox through Controlled Cationic Disordering.

Lithium-rich layered oxides (LLOs) capable of supporting both cationic and anionic redox chemistry are promising cathode materials. Yet, their initial charge to high voltages often trigger significant oxygen evolution, resulting in substantial capacity loss and structural instability. In this study, we applied a straightforward low-potential activation (LOWPA) method alongside a relatively stable electrolyte to address this issue. This approach enables precise control over the order-to-disorder transformation of the transition metal layers in LLOs, producing an in-plane cation-disordered Li1.2Mn0.54Co0.13Ni0.13O2 that averts irreversible oxygen evolution at 4.8 V by stabilizing Mn-O2 or Mn-O3 species within the Li/Mn-disordered nanopores. Consequently, an ultrahigh reversible capacity of 322 mAh g-1 (equating to 1141 Wh kg-1), 91.5% initial Coulombic efficiency, and enhanced durability and rate capability are simultaneously achieved. As LOWPA does not alter any chemical composition of LLOs, it also offers a simple model for untangling the complex phenomena associated with oxygen-redox chemistry.

Systematic Study on Swelling/Delamination of Layered Metal Oxides with Quaternary Ammonium Ions: Production of Well-Shaped/Oversized Unilamellar Nanosheets.

Enormous swelling of layered host compounds in an aqueous solution of various amines has been investigated as an important step in the synthesis of molecularly thin 2D nanosheets. However, a complete understanding of the reaction process has not been attained, which is the barrier for producing high-quality unilamellar nanosheets. Here, the swelling and delamination behaviors of platelet single crystals of protonated layered metal oxides are systematically examined with a series of tetraalkylammonium (TAA) hydroxide solutions. Upon contact with the solutions, the crystals immediately underwent massive expansion by several tens to hundreds of times. The swollen crystals can be delaminated into elementary layers by the application of external shear force. The exfoliation behavior is dependent on TAA ions, especially in terms of yield and lateral size/shape of the delaminated nanosheets. The swollen crystals with TAA ions with longer alkyl chains are delaminated almost completely, but irregular and fractured small sheets are yielded. Such long alkyl chains become entangled on the oxide layer and resulting hydrophobic interactions may be responsible for the lateral fragmentation. It is found that replacement of aqueous solutions with organic solvents to suppress the hydrophobic interactions is effective to produce oversized nanosheets in rectangular shape with sharp edges.

A new method for estimating nanoparticle deposition coverage from a set of weak-contrast SEM images

Imaging nanomaterials in hybrid systems is critical to understanding the structure and functionality of these systems. However, current technologies such as scanning electron microscopy (SEM) may obtain high resolution/contrast images at the cost of damaging or contaminating the sample. For example, to prevent the charging of organic substrate/matrix, a very thin layer of metal is coated on the surface, which will permanently contaminate the sample and eliminate the possibility of reusing it for following processes. Conversely, examining the sample without any modifications, in pursuit of high-fidelity digital images of its unperturbed state, can come at the cost of low-quality images that are challenging to process. Here, a solution is proposed for the case where no brightness threshold is available to reliably judge whether a region is covered with nanomaterials. The method examines local brightness variability to detect nanomaterial deposits. Very good agreement with manually obtained values of the coverage is observed, and a strong case is made for the method's automatability. Although the developed methodology is showcased in the context of SEM images of Polydimethylsiloxane (PDMS) substrates on which silicone dioxide (SiO2) nanoparticles are assembled, the underlying concepts may be extended to situations where straightforward brightness thresholding is not viable.

Microstructural characterizations of metallized Al2O3 before/after surface treatment and Al2O3/Cu soldered joint

Joining Al2O3 ceramics to Cu heat pipes should be conducted at low temperatures since Cu heat pipes may fail at temperatures higher than 320 °C. Due to the poor wettability of low-temperature solder on Al2O3 ceramics, it is essential to metallize Al2O3 ceramics before joining Al2O3 to Cu with a low-temperature solder. Surface metallization of Al2O3 has been conducted using Ag-Cu-Ti active metal filler at 900 °C. Microanalysis indicates that an interfacial reaction occurs between the active metal filler and the Al2O3, leading to the formation of a Cu3Ti3O reaction layer. The metal layer on the surface of Al2O3 is primarily composed of Ag (s, s) (solid solution), Cu (s, s) and Ti2Cu. The polishing treatment of the surface metal layer in metallized Al2O3 results in a reduction of the oxide content and contaminants, which subsequently allows joining at low temperature. Low-temperature joining of metallized Al2O3 to Cu has been carried out using Sn-Ag-Cu solder at 280 °C. The joining area of the joint includes a Cu3Ti3O reaction layer, a metal layer and a solder layer. The solder layer mainly consists of Sn (s, s), Ag3Sn and Cu6Sn5. The Al2O3/Cu joint fractures in the solder layer after the shearing test, indicating that the strength of the solder is relatively low. However, the interfacial bonding between the metallized Al2O3, solder layer and Cu base material is satisfactory.

Solvent-mediated oxide hydrogenation in layered cathodes.

Self-discharge and chemically induced mechanical effects degrade calendar and cycle life in intercalation-based electrochromic and electrochemical energy storage devices. In rechargeable lithium-ion batteries, self-discharge in cathodes causes voltage and capacity loss over time. The prevailing self-discharge model centers on the diffusion of lithium ions from the electrolyte into the cathode. We demonstrate an alternative pathway, where hydrogenation of layered transition metal oxide cathodes induces self-discharge through hydrogen transfer from carbonate solvents to delithiated oxides. In self-discharged cathodes, we further observe opposing proton and lithium ion concentration gradients, which contribute to chemical and structural heterogeneities within delithiated cathodes, accelerating degradation. Hydrogenation occurring in delithiated cathodes may affect the chemo-mechanical coupling of layered cathodes as well as the calendar life of lithium-ion batteries.

Структурные особенности и трибологические свойства многослойных высокотемпературных плазменных покрытий

Introduction. Multilayer high-temperature coatings obtained using plasma spraying, are studied. The combination of layers of different chemical and phase compositions made it possible to increase wear resistance by 1.5–2.0 times. The purpose of this work is to study the influence of the chemical composition of sprayed coatings on the phase composition, structure, micromechanical and tribological characteristics under conditions of dry sliding friction of surface layers. Materials and methods of research. Coatings A and B consist of sequentially sprayed layers. The first and second layers were sprayed in a reducing atmosphere: the first layer was a heat-resistant self-fluxing powder of two systems: 1 – Fe-Cr-Si-Mn-B-C for coating A and 2 – Fe-Ni-Si-Mn-B-C for coating B; the second layer was a mixture of self-fluxing powder with iron powder in a 1:1 ratio. The third layer was obtained by spraying iron powder in an oxidizing atmosphere to form a metal oxide coating. To create a layer of scale on the surface, coated specimens were subjected to high-temperature annealing at a temperature of 1,000 ℃. The chemical composition and nature of the distribution of elements over the thickness of the coatings were determined by micro-X-ray spectral analysis using a TWSCAN scanning electron microscope with an Oxford energy-dispersive attachment. Microhardness and micromechanical properties were studied using an instrumental microhardness tester of the Fischerscope HM2000 XYm system at a load of 0.980 N. Determination of tribological properties was carried out on a laboratory installation using the “finger-disc” scheme at loads of 30, 75, 100 and 130 N. To measure roughness parameters and obtain 3-D profilometry of surfaces after testing, a non-contact profilometer-profiler Optical profiling system Veeco WYKO NT 1100 was used. Results and discussion. Metallographic studies have shown that the formed multilayer coatings consist of an internal metal layer and an external oxide layer with a total thickness of the entire coating up to 800–850 μm. It is established that the first sprayed layer has the highest level of microhardness, which is due to the high-volume fraction of the strengthening phases contained in it (~ 95 %). It is shown that the coating A has increased wear resistance, which is expressed by minimal weight loss (~ 1.5 times less than that of the coating of the coatimg B), the friction coefficient was f = 0.3 for coating A and f = 0.4 for coating B. The study of wear surfaces has shown that for all selected test loads under sliding friction conditions, the coating of both compositions was preserved, even at a maximum load of 130 N.

A novel dual functional gradient Zn(O,S)/Mg electron-selective contact for dopant‐free silicon solar cells with efficiencies approaching 21 %

Dopant-free carrier-selective contacts have the potential to mitigate or eliminate parasitic absorption, auger recombination losses, etc. Therefore, the vigorous development of dopant-free carrier-selective contact materials is an important way to enhance the performance of crystalline silicon (c-Si) photovoltaics. This study presents the concept of magnetron sputtering gradient deposited zinc oxide (Gd-Zn(O,S)) combined with a low work function magnesium metal layer. Subsequently, the Gd-Zn(O,S)/Mg bifunctional layer was further investigated and optimised to determine its suitability as a contact layer for electron transfer in c-Si solar cells. This strategy simultaneously enables a good passivation and a low contact resistance. The c-Si(n)/a-Si:H(i)/Gd-Zn(O,S)/Mg devices are constructed and achieved an optimal contact recombination current density (J0) of approximately 1.51 fA cm−2, along with a minimum ρc of approximately 35.89 mΩ.cm2. As a consequence, the power conversion efficiency of a prototype silicon heterojunction solar cell is 20.92 %. This study demonstrates that the strategy of replacing the a-Si:H(n) electron transport layer with Gd-Zn(O,S) is an effective approach for improving the SHJ cell. This study also provides new perspectives for designing novel dopant-free carrier-selective contact structures.

A Novel 4-Fluorophenyl Isocyanate Additive Constructing Solid Cathodes-Electrolyte Interface for High-Performance Lithium-Ion Batteries.

Building a stable cathode-electrolyte interface (CEI) is crucial for achieving high-performance layered metal oxide cathode materials LiNixCoyMn1-x-yO2 (NCM). In this work, a novel 4-fluorobenzene isocyanate (4-FBC) electrolyte additive that contains isocyanate and benzene ring functional groups is proposed, which can form robust and homogeneous N-rich and benzene ring skeleton CEI film on the cathode surface, leading to significant improvement in the electrochemical performance of lithium-ion batteries. Taking LiNi0.5Co0.2Mn0.3O2 (NCM523) as an example, the NCM523/SiO@Graphite pouch full cells with electrolytes containing a mass fraction of 1% 4-FBC additives demonstrate improved capacity retention after 200 cycles, retaining capacity retention rates of 81.3%, which is much higher than that of 39.1% without additive. The improvement can be ascribed to the mitigation of electrolyte decomposition and inhibition of transition metal ions the dissolution from the cathode material due to the stable CEI film. Moreover, the electrochemical performance enhancement can also be achieved in high voltage and Ni-rich cathode materials, indicating the universality and effectiveness of this strategy for the practical applications of high energy density lithium-ion batteries.

Topography control and component design strategies to enhance electrochemical performance of O3-Type cathode materials for Sodium-ion batteries

Layered transition metal oxides (NaxTMO2, 0 < x ≤ 1) are considered one of the most promising cathodes for Sodium-ion batteries (SIBs) due to their high theoretical capacity and operability. However, NaxTMO2 still faces significant challenges, including poor kinetic performance and low energy efficiency. Herein, in order to enhance the kinetics of NaNi1/3Fe1/3Mn1/3O2 (NaNFMO), topography control and component design were proposed: First, Cu doping (Cu-NaNFMO) was used to expand lattice channels and improve “flat sheet” of layered oxide, which synergistically enhanced transport kinetics of Na+. Second, Co coating (NaNFMO@Co) reacted with surface residue to form a fast-ionic conductor NaxCoO2 (0 < x ≤ 1), which inhibited interfacial side reactions and enhanced transport kinetics of Na+. Furthermore, the presence of strong Cu-O bonds in Cu-NaNFMO and fast-ionic conductor NaxCoO2 in NaNFMO@Co led to better electrochemical redox performance, the initial charge specific capacity of NaNFMO was increased from 141.5 mAh g⁻1 to 145.8 mAh g⁻1 and 144 mAh g⁻1, with capacity retention improving by nearly 10 % after 100 cycles. Furthermore, NaNFMO@Co improves ICE from 90.56 % to 93.57 %. With the improved kinetics, the DCR of pouch cells decreased, and the energy efficiency increased from 93.3 % to 94 % and 95.7 %.

CMOS-based micro-fluxgate with racetrack core and solenoid coils

This work introduces an integrated fluxgate sensor fabricated using CMOS chip technology. The sensor uses a “racetrack” shape of the core. The material used for the core is VITROVAC 6025F, and the shape was laser-cut from 25 μm thick foil. The coils are solenoids fabricated using metal layers of the chip and bonding wires. Sensing and excitation coils have 60 and 40 turns respectively. TSMC D35 technology was used for fabrication. The size of the core is 8 mm × 1.75 mm. Dimensions of the chip are 8 mm × 2.7 mm (21.6 mm2).The sensor was tested in open-loop operation using a sinewave excitation. Sensitivity increases with frequency up to 1.5 MHz, reaching 5000 V/T. This is a significantly higher value than what can be achieved using a flat pick-up coil (around 10 V/T). Fully saturating the core requires a 110 mA excitation current, leading to 300 mW power dissipation in the coil. The Core loss is 100 mW at 1 MHz excitation. The Noise at 1 Hz may be as low as 2nT/Hz depending on excitation signal parameters. The typical offset is below 1 μT.

High-Performance Visible-to-SWIR Photodetector Based on the Layered WS2 Heterojunction with Light-Trapping Pyramidal Black Germanium.

This study presents a layered transition metal dichalcogenide/black germanium (b-Ge) heterojunction photodetector that exhibits superior performance across a broad spectrum of wavelengths spanning from visible (vis) to shortwave infrared (SWIR). The photodetector includes a thin layer of b-Ge, which is created by wet etching of germanium (Ge) wafer to form submicrometer pyramidal structures. On top of this b-Ge layer, the WS2 thin film is deposited using pulsed laser deposition. In comparison to conventional germanium, b-Ge absorbs about 25% more light between 850 and 1750 nm wavelengths. The WS2/b-Ge photodetector has a peak photoresponsivity of 0.65 A/W, which is more than twice the photoresponsivity of the WS2/Ge photodetector at 1540 nm. Additionally, it shows better responsivity and response speed compared with other similar state-of-the-art photodetectors. Such an improvement in the performance of the device is credited to the light-trapping effect enabled by the germanium pyramids. Theoretical simulations employing the finite-difference time-domain technique help validate the concept. This novel photodetector holds promise for efficient detection of light across the vis to SWIR spectrum.

Preparation and characterization of ZnS/metal/ZnS transparent conductive multilayer films with different metal layers

ZnS/metal/ZnS transparent conductive multilayer films were deposited on quartz glass by pulsed laser deposition at room temperature with Au, Ag and Cu as the metal layers, and annealed in air at 100, 200 and 300℃ for 1 h. XRD patterns show that β -ZnS(111) diffraction peak of ZnS/Au/ZnS is stronger and sharper than the other two samples, indicating that its crystalline quality is the best. SEM images show the good structural homogeneity of the samples with smooth and compact film surfaces. When the annealing temperature increases from 100 to 300℃, the sheet resistance decreases first and then increases, while the carrier concentration changes in the opposite trend. The maximum transmittance (~85%) for ZnS/Au/ZnS in the visible light region is observed when the sample is annealed at 200℃. The figure of merit is calculated, and the best sample suitable for transparent conductive electrode is determined.

Enhanced adsorption of radioactive cesium from nuclear wastewater using ZIF-67 laminated 2D MXene Ti3C2

Development of nuclear industry has caused severe water pollution. Adsorptive removal of radionuclides from wastewater has been regarded as effective solution for environment. However, developing adsorbents with high adsorption capacity and selectivity for removal of radionuclides (such as 137Cs) is still a challenge. Herein, we adopted an in situ assemble strategy to construct a novel composite, in which zeolitic imidazolate framework (ZIF-67) was grafted into two-dimension (2D) layers of transition metal carbides/nitrides (MXenes) Ti3C2, and used it in adsorptive removal of Cs+ from wastewater. Laminated and pillaring effect of ZIF-67 increased interlayer spacing and specific surface area of Ti3C2, significantly enhancing Cs+ adsorption. MXenes matrix provided the main adsorptive sites and interaction to stabilize Cs+, while the hybrid ZIF-67 assisted adsorption. The adsorbent achieved 96.2 % removal for 5 mg·L-1 of Cs+ within 6 h, and 50.0 mg·g−1 of maximum adsorption capacity, with good recyclability for 4 times. Ion competition, kinetics and thermodynamics were studied in detail to obtain the behavior of Cs+ adsorption. Finally, adsorption mechanism was proposed that [Ti − O] − H+ and [Ti − O] groups of 2D Ti3C2 were main adsorptive sites to participate in ion exchange and complexation with Cs+, respectively, while 2-methylimidazole (2-MI) ligands in ZIF-67 were synergetic adsorption sites.

Achieving a comparable transverse magneto-optical Kerr effect by spin–orbit field driven magnetoplasmonic

In this study, we propose and simulate a magnetoplasmonics heterostructure that utilizes spin–orbit fields to generate an internal magnetic field and create a significant magneto-optical effect. Our approach offers a new way to overcome the challenges of using permanent magnets or magnetic coils in conventional magnetoplasmonics, such as high-power consumption and non-scalability. We demonstrate that it is possible to create an appropriate amount of magnetic field using spin–orbit fields induced by the spin-Hall effect, such that the consumption power becomes reasonable and the dimensions could be miniaturized. This approach will be an important development in the field of magneto-optics, as it can lead to enhanced transverse magneto-optical Kerr effect in the present of surface plasmon polaritons. The proposed nanostructure consists of a ferromagnetic film adjacent to a heavy metal layer, both sandwiched between two noble metal films, and deposited on a dielectric prism. The strength of the Kerr signal strongly depends on the thickness of the ferromagnetic layer, with the maximum effect observed at a thickness of 5nm. This concept has potential for various nanophotonic and spintronic applications, particularly for developing high-speed active plasmonic devices for ultrafast light modulation.