Melt-blown Nonwoven Fabrics Research Articles

Flexible temperature sensor based on RGO/CNTs@PBT melting blown nonwoven fabric

The flexible smart wearable device with low cost and high performance is highly desired but rather challenging. In this work, a wearable temperature sensor was developed by integrating the polybutylene terephthalate melt-blown nonwoven fabric (PBT NW) with reduced graphene oxide (rGO) and carbon nanotubes (CNTs) via a simple mechanical ultrasonication method. The microstructures of the rGO/CNTs@PBT NW sensor were investigated by FT-IR, XRD, and SEM techniques, and the thermal and mechanical properties of this sensor were systematically analyzed. The conductive rGO and CNTs could be tightly fixed to the surface of PBT NW. Compared with original PBT NW, the tensile properties of rGO/CNTs@PBT NW sensor were improved. The results of sensing performance tests showed that the prepared temperature sensor had high sensitivity (−0.737% °C−1) and linearity (R2 =0.98) with a resolution of 0.1 °C between 25 °C and 45 °C, a long-term stability and good circularity indicating that our sensor can meet the monitoring requirement of real-time human body temperature. In addition, this sensor could also be used to monitor human respiratory rate. Our study may provide a new idea for the fabrication of the flexible temperature sensor with nonwoven substratefor monitoring the human body and environment temperature.

Triboelectric charging of melt-blown nonwoven filters with high filtration efficiency

As a novel technology to convert low-frequency energy into electric power, the triboelectric nanogenerator is a hot research topic recently. However, the nature of charge carriers and their transfer mechanisms still remain poorly understood, especially for the cases of liquid–solid triboelectric nanogenerator. In this paper, charges produced by a triboelectric charging process were designed to provide melt-blown nonwoven fabrics with high filtration efficiency by making full use of the electrostatic attraction filtration mechanism. Influences of water conductivity and drying temperature on the filtration efficiency of melt-blown nonwoven fabrics were investigated. And the corresponding properties such as the surface charge potential and charge stability were analyzed by using the electrostatic voltmeter, bio atomic force microscope and thermally stimulated discharge technique. In addition, metal and inorganic elements in the masterbatch and water before and after triboelectric charging were measured in order to uncover the charge transfer mechanism. Melt-blown nonwoven fabrics with filtration efficiency as high as 96.8% was obtained through the triboelectric charging treatment by using water with the conductivity as low as 1.1 μS/cm for the first time. Negative and positive surface charge density appeared randomly on both sides of melt-blown nonwoven fabrics after the triboelectric charging treatment from the bio atomic force microscope measurement while only one kind of surface charge density can be achieved in the research of TENG, that is, negative or positive. It seems there are both electron and ion transfers during the triboelectric charging process and electron transfer seems to have more important contribution for the generation of charges.

Investigation of sound transmission loss of natural fiber/rubber crumbs composite panels

Natural fibers and their waste are widely used all over the world, and their production has been increasing continuously. But, the rubber crumbs from used tire disposal are nonbiodegradable and present significant problems about their end-of-life given a critical environmental impact. These problems require recycling policies to provide the collection and recycling of used clothing, textile wastes, and rubber crumbs. In this work, the acoustic properties of insulator panels from the combination of textile fibers and rubber crumbs material were analyzed. Insulator panels demonstrated a good sound transmission loss (STL) characteristic, especially at high frequencies. The STL of the manufactured panels from a combination of fiber (cotton, wool, and Kapok) and rubber crumbs was investigated at the different sound frequencies. Results indicated that the fiber/rubber crumbs panel had a significant STL profile of 47 dB, 40 dB, and 35 dB, for Kapok, wool, and cotton, respectively. The addition of polylactic acid meltblown nonwoven fabric on the surface of the rubber crumbs side considerably increases the STL by 20%.

Controlled Degradation of Commercial Resin for Meltblown Nonwoven Fabric Sheet Production.

Manufacturing meltblown nonwoven fabrics requires special grades of resin with very low viscosity, which are not dealt with so much on market and cost quite high compared to the standard grades. We propose a high-shear rate processing method that can quickly and easily produce such low-viscosity resin from the commercial one without using organic peroxides. In this method, we apply high-shear stress to molten resin by using a high-shear extruder, which is a single screw extruder with high screw rotation speed, and the resin is thermally decomposed of its shear-induced heat which is quickly generated. We found that polypropylene with a value of melt flow rate over a thousand, which was required for the meltblown process, was produced from the standard grade with the high-shear extruder at the screw rotation speed of 3600 min and the barrel temperature over 300 C. Using the degradated polypropylene, a meltblown nonwoven fabric sheet was successfully fabricated. We also developed a numerical simulator of the high-shear extruder which can handle a wide range of the screw rotation speed and barrel temperature by the Nusselt number modulated with the operational conditions. The experimental values of the zero-shear viscosity and temperature at the exit of the extruder agreed well with the simulation results. Our high-shear rate processing method will enable us to quickly and easily produce various meltblown nonwoven fabric sheets at low costs.

Preparation of Ag@ZIF-8@PP Melt-Blown Nonwoven Fabrics: Air Filter Efficacy and Antibacterial Effect.

Serving as matrices, polypropylene (PP) melt-blown nonwoven fabrics with 4% electrostatic electret masterbatch were incorporated with a 6%, 10%, 14%, or 18% phosphorus-nitrogen flame retardant. The test results indicate that the incorporation of the 6% flame retardant prevented PP melt-blown nonwoven fabrics from generating a molten drop, which, in turn, hampers the secondary flame source while increasing the fiber diameter ratio. With a combination of 4% electrostatic electret masterbatch and the 6% flame retardant, PP melt-blown nonwoven fabrics were grafted with ZIF-8 and Ag@ZIF-8. The antibacterial effect of ZIF-8 and Ag@ZIF-8 was 40% and 85%, respectively. Moreover, four reinforcing measures were used to provide Ag@ZIF-8 PP melt-blown nonwoven fabrics with synergistic effects, involving lamination, electrostatic electret, and Ag@ZIF-8 grafting, as well as a larger diameter because of the addition of phosphorus-nitrogen flame retardants. As specified in the GB2626-2019 and JIS T8151-2018 respiratory resistance test standards, with a constant 60 Pa, Ag@ZIF-8 PP melt-blown nonwoven membranes were tested for a filter effect against PM 0.3. When the number of lamination layers was five, the filter effect was 88 ± 2.2%, and the respiratory resistance was 51 ± 3.6 Pa.

Responsibilities of petroleum prospectors: Discussions on dual logic and development trend of hydrocarbon exploration

Some unusual events happened in petroleum industry in 2020, such as the negative WTI oil price, price soaring of melt-blown nonwoven fabric, Exxon Mobil Corp.(NYSE:XOM) removed from Dow Jones Industrial Average, and the oil demand peak theory proposed by BP Energy Outlook 2020 Edition. These events have made profound impact on petroleum exploration. Prospecting is at the forefront of petroleum industry chain, and prospectors have great influence on petroleum industry. The responsibility of petroleum prospectors is to find oil, which calls for the correct way of thinking as well as scientific and technical means, both of which are indispensable. When it comes to the cognition of petroleum exploration, we should draw lessons from predecessors' philosophy of finding oil from a development perspective. It is necessary to define the relationship between subject activity and objective structure, as there is an inherent tension between the two and a dialectical relationship that complements each other. It is also essential to illustrate the logic of initiative and decisiveness, as between the two is the dual logic of active logic that changes the world and deterministic logic based on science and technology. The strategic breakthrough in the Gulong shale oil exploration in Daqing is a typical example. Our knowledge and practice of oil exploration has overthrown the Hubbert Curve. The new curve may have more than one peak, which means hopes are always there for finding oil. Climbing to the top of a mountain must start from the foot. A journey of a thousand miles must begin with a single step. Looking forward to the future, prospectors have the wisdom, ability, and methods to find more, cleaner, and more affordable oil to drive the progress of human civilization. This is the duty of petroleum prospectors.

Filtering efficiency measurement of respirators by laser-based particle counting method

Respirators are one of the most useful personal protective equipment which can effectively limit the spreading of coronavirus (COVID-19). There are a worldwide shortage of respirators, melt-blown non-woven fabrics, and respirator testing possibilities. An easy and fast filtering efficiency measurement method was developed for testing the filtering materials of respirators. It works with a laser-based particle counting method, and it can determine two types of filtering efficiencies: Particle Filtering Efficiency (PFE) at given particle sizes and Concentration Filtering Efficiency (CFE) in the case of different aerosols. The measurement method was validated with different aerosol concentrations and with etalon respirators. Considerable advantages of our measurement method are simplicity, availability, and the relatively low price compared to the flame-photometer based methods. The ability of the measurement method was tested on ten different types of Chinese KN95 respirators. The quality of these respirators differs much, only two from ten reached 95% filtering efficiency.

Reusable Self-Sterilization Masks Based on Electrothermal Graphene Filters

Surgical mask is recommended by the World Health Organization for personal protection against disease transmission. However, most of the surgical masks on the market are disposable that cannot be self-sterilized for reuse. Thus, when confronting the global public health crisis, a severe shortage of mask resource is inevitable. In this paper, a novel low-cost electrothermal mask with excellent self-sterilization performance and portability is reported to overcome this shortage. First, a flexible, ventilated, and conductive cloth tape is patterned and adhered to the surface of a filter layer made of melt-blown nonwoven fabrics (MNF), which functions as interdigital electrodes. Then, a graphene layer with premier electric and thermal conductivity is coated onto the MNF. Operating under a low voltage of 3 V, the graphene-modified MNF (mod-MNF) can quickly generate large amounts of heat to achieve a high temperature above 80 °C, which can kill the majority of known viruses attached to the filter layer and the mask surface. Finally, the optimized graphene-modified masks based on the mod-MNF filter retain a relatively high particulate matter (PM) removal efficiency and a low-pressure drop. Moreover, the electrothermal masks can maintain almost the same PM removal efficiency over 10 times of electrifying, suggesting its outstanding reusability.

Study on the Relationship Between Structure Parameters and Filtration Performance of Polypropylene Meltblown Nonwovens

Abstract In this study, polypropylene meltblown nonwoven fabrics with different structure parameters such as fiber diameter, pore size, and areal density were prepared by the industrial production line. The morphology of meltblown nonwoven fibers was evaluated by using scanning electron microscope, and the diameter of fibers was analyzed by using image-pro plus software from at least 200 measurements. The pore size of nonwoven fabric was characterized by a CFP-1500AE type pore size analyzer. The filtration efficiency and pressure drop were evaluated by TSI8130 automatic filter. The results showed that the pressure drop of nonwoven fabrics decreased with the increase in pore size; the filtration efficiency and the pressure drop had a positive correlation with the areal density. However, when the areal density is in the range of 27–29 g/m2, both filtration efficiency and pressure drop decreased with the increase of areal density; when the areal density was kept constant, the filtration efficiency decreased as the pore size decreased; when the pore size of the meltblown nonwoven fabric is less than 17 μm, the filtration efficiency increased as the pore diameter decreased; when the pore diameter of the nonwoven fabric is larger than 17 μm. In a wide range, the pressure drop decreased as the fiber diameter decreased.

Effect of Electret Process Parameters on Filtration Performance of Polypropylene Melt-Blown Nonwoven Fabric

With the spread of the novel coronavirus, masks become daily necessities, and their protective effect mainly depends on the core materials, so improving the performance of the core material polypropylene melt-blown nonwoven fabric has become the current research hotspot. The filtration performance of PP melt-blown nonwoven fabric mainly depends on the electret process parameters. The electret treatment of PP melt-blown nonwoven fabric is carried out by using high voltage corona discharge. The research on the influence of the electret process parameters, such as charging time, charging voltage and charging distance, on the filtration performance of PP melt-blown nonwoven fabric will have guiding significance for the practical production. In this paper, after a lot of research and experimental work, find out the influence of process parameters on the filtration performance of nonwoven fabrics. It is found that the best condition for the sample is the charge time of 12 min, the charge voltage of 15 kV and the charge distance of 4 cm. The filter efficiency is 90.2%, which is more than 1.5 times higher than that before the sample. The air permeability of melt-blown nonwovens after electret treatment did not decrease.

High performance flexible wearable strain sensor based on rGO and AgNWs decorated PBT melt-blown non-woven fabrics

Flexible strain sensors have attracted wide attention to the field of applications on wearable electronic devices. However, they still have numerous defects, such as low linearity and low sensitivity. In this paper, high-elastic polybutylene terephthalate (PBT) melt-blown non-woven fabric (MB) was chosen as the substrate of the strain sensor. The reduced graphene oxide (rGO) and silver nanowires (AgNWs) were loaded on the PBT MB surface by simple ultrasonic treatments to form a dense and stable conductive path. The sensing properties of the sensors loaded with the different concentration load ratios of rGO and AgNWs were studied and the best load ratio was 1:0.9. The results showed that the sensor has excellent sensing characteristics, including wide range of applications (90 %), extremely high sensitivity (guage factor (GF) up to 1829 at 80 % strain). Finally, the strain sensor has demonstrated in monitoring an assortment of human-exercises even some subtle physiological signals.

Development of Anti-Bacterial and Anti-Viral Nonwoven Surgical Masks for Medical Applications

This article aims to investigate the development of surgical masks for medical applications by incorporating biocidal silver nanoparticles. Medical masks were developed in three layers of a nonwoven fabric, where the outer and inner layers were made of a spun-bond polypropylene nonwoven fabric and the middle layer con­sisted of a melt-blown nonwoven polypropylene fabric. In this study, silver nanoparticles in the concentrations of 1–5% were applied to masks with the pad-dry-cure method. The samples were cured at room temperature and subsequently examined for antimicrobial properties. Scanning electron microscopy, energy dispersive spectroscopy and Fourier transform infrared spectroscopy were used to investigate the morphological charac­teristics and chemical composition of the samples. Microbial cleanliness, bacterial filtration efficiency, antiviral effect and breathability tests were performed according to standard test protocols. The results revealed that the application of silver nanoparticles to a three-layer mask rendered the end product with outstanding anti­microbial and antiviral properties with poor breathability (air permeability) results.

Superabsorbent Fibers for Comfortable Disposable Medical Protective Clothing.

Disposable medical protective clothing for 2019-nCoV mainly consists of stacked layers with nanopore films, polymer coated nonwoven fabrics and melt-blown nonwoven fabrics against anti-microbial and anti-liquid penetration. However, such structures lack moisture permeability and breathability leading to an uncomfortable, stuffy wearing experience. Here, we propose a novel medical protective clothing material with a superabsorbent layer to enhance moisture absorption. Poly(acrylic acid-co-acrylamide)/polyvinyl alcohol superabsorbent fibers (PAAAM/PVA fibers) were prepared via wet spinning. And the superabsorbent composite layer was stacked from PAAAM/PVA fibers, bamboo pulp fibers (BPF) and ethylene-propylene side by side fibers (ESF). The novel disposable medical protective composite fabric was obtained through gluing the superabsorbent layer to the inner surface of strong antistatic polypropylene nonwoven fabric. The resultant composite fabric possesses excellent absorption and retention capacity for sweat, up to 12.3 g/g and 63.8%, and a maximum hygroscopic rate of 1.04 g/h, higher than that of the conventional material (only 0.53 g/h). The moisture permeability of the novel material reached 12,638.5 g/(m2 d), which was 307.6% of the conventional material. The novel material can effectively reduce the humidity inside the protective clothing and significantly improve the comfort of medical staff.

Durability and adsorption of heavy metal ions of glass-geogrid-reinforced geosynthetic clay liners

Geosynthetic clay liners (GCLs) are commonly used in engineering to prevent seepage. These liners’ surface fabric often suffers damage, especially in toxic environments and under high pressure. To mechanically strengthen the GCLs, this study proposes reinforcement by using needle bonding and glass geogrid to establish glass-geogrid-reinforced GCLs (i.e., GGCLs), consisting of glass geogrid, bentonite layer, and 0.3 mm thick melt-blown nonwoven fabric. Tensile durability of GGCLs was determined by exposing them to thermal oxidation and UV degradation. Hydraulic conductivity and heavy metal ions adsorption of GGCLs was explored to simulate the damage caused by garbage leachate. Tensile strengths of polyamide (PA)- and polyethylene terephthalate (PET)-contained GGCLs retained greater than 73% and 90%, respectively, even after 20 h thermal oxidation at 100°C and 60 h UV degradation. Improvement of hydraulic conductivity after 2 h adsorptions of Cu2+, Ni2+, and Pb2+ reached 51.09, 51.04, and 45.56%. The absorptions of Cu2+ and Ni2+ conformed to the quasi-secondary dynamics model, but that of Pb2+ followed both the quasi-first-order and quasi-secondary dynamics models. The mechanical properties and impermeability of the resulting GGCLs declined under the simulated conditions. This study provides a basic theory to predict the durability and adsorption of heavy metal ion of landfill GGCLs under natural and severe weather conditions.

Preparation and Characterization of magnetic PLA/Fe3O4-g-PLLA composite melt blown nonwoven fabric for air filtration

A kind of magnetic poly (lactic acid) (PLA) melt blown nonwoven fabric (MB) was fabricated by the introduction of ferroferric oxide (Fe3O4) nanoparticles to improve its air filtration performances. In view of the poor compatibility of two components, the poly (L-lactic acid) (PLLA) molecular chains was firstly grafted onto the Fe3O4 nanoparticles surface via the ring opening polymerization (ROP). Then, PLA/Fe3O4-g-PLLA composite masterbatches with different mass ratios were prepared by melt-blending method and processed into the corresponding composite MB. The structures and performances of PLA/Fe3O4-g-PLLA composite masterbatches and their MB were investigated. The results showed that the addition of Fe3O4-g-PLLA nanohybrids hardly influenced the glass transition, cold crystallization and melting behaviors of the composite masterbatches. Though the melt fluidity of the composite masterbatches reduced with the Fe3O4-g-PLLA content increasing, the composite masterbatches still could present the appropriate processability in the range of 210°C to 230°C. Fe3O4-g-PLLA could be uniformly dispersed in PLA matrix and had a good interfacial compatibility with the matrix. Compared with pure PLA MB, the fiber surface of the composite MB became slightly rough, the pore size and distribution of the fiber web increased. The addition of Fe3O4-g-PLLA endowed PLA MB with magnetism. With the increasing of Fe3O4-g-PLLA content, the air permeability of the composite MB was improved and their filtration resistance obviously reduced. When the content of Fe3O4-g-PLLA was 0.5 wt%, the filtration efficiency of the composite MB reached the maximum. Moreover, the composite MB have higher longitudinal tensile strength and elongation at break than those of pure PLA MB.

Coalescence efficiency of surface modified PBT meltblown nonwovens in the separation of water from diesel fuel containing surfactants

Abstract Removal of water from diesel fuel is essential to ensure efficient operation of High-Pressure Common-Rail (HPCR) fuel injection systems used in modern diesel engines. The presence of surfactants in modern fuels (including biofuels) can create conditions in which the interfacial tension between water and fuel is reduced, leading to coalescing media being “disarmed” and less effective in separation. To elucidate this phenomenon in industrially available depth coalescing media, the coalescence efficiency of surface-modified poly (butylene terephthalate) (PBT) meltblown nonwoven fabrics possessing a wide range of wetting behaviours was studied. Tuning of the wettability was accomplished by alkaline hydrolysis of the medium. Using reference grade diesel fuel with and without added surfactants, the coalescence efficiency and quality factor were studied by means of a purpose-built coalescence test rig. The coalescence efficiency was found to depend on both the fuel composition and the wettability of the treated PBT and the optimum efficiency for each test fuel required a difference in wettability of the PBT. For reference grade diesel, increasing the wettability to ‘intermediate’ level improved coalescence efficiency, but the quality factor can be negatively affected by water droplet retention within the medium. The reduced quality factor associated with hydrophilic media was even more pronounced in fuels containing surfactants due to increased pressure drop and re-emulsification of the fuel in water. These findings highlight the practical challenges that exist in engineering a “universal” coalescing medium suitable for removing water from diesel fuels containing surfactants, based solely on the modulation of fibre wettability and hydrophilicity.

Concentration levels of selected analytes in the gas phase of an e-cigarette aerosol

The aerosols generated from e-cigarettes are composed of liquid and gas phases resulting from vapourized e-liquid. The apportioning of substances from e-liquid into the liquid and gas phases during e-cigarette use has not been extensively studied. Partitioning of e-liquid components between the gas and the liquid phase of the aerosol influences the substances inhaled and exhaled by the users, leading to second-hand exposure. It seems important to determine which compounds and how much of them are transferred into the gas phase and may immediately enter the bloodstream. For this purpose, a method based on thermal desorption followed by gas chromatography coupled with tandem mass spectrometry (GC–MS/MS) in electron ionization mode was developed. As in a previous study, an automatic generator of an aerosol from an e-cigarette with a collection tube filled with melt-blown non-woven fabric discs and equipped with Tenax TA sorption tubes was used. The melt-blown non-woven fabric is designed to capture liquid phase compounds, while sorption tubes are meant to sorb compounds in the gas phase of the aerosol. To control the e-liquid mass changes before and after a puff session, quantitation based on the mass change tracking approach (MCT) was applied. Accuracy of the developed method ranged between 91% and 110% regardless of the spiking level, with precision and reproducibility better than 10%. The limits of detection (LODs) ranged from 0.015 to 0.076 ng of substance emitted/mg of consumed e-liquid, while limits of quantitation (LOQs) ranged from 0.045 to 0.23 ng of substance emitted/mg of consumed e-liquid. Most of the compounds are deposited in the liquid phase of the aerosol, while only trace levels of some substances may be observed in an actual, non-condensed gas phase.

New approach for e-cigarette aerosol collection by an original automatic aerosol generator utilizing melt-blown non-woven fabric

Currently, there is lack of standardized conditions for the collection and analysis of e-cigarette (EC) aerosol. Considering the urgent need for the development of these guidelines, a procedure for EC aerosol analysis was developed. A novel automatic e-cigarette aerosol generator was designed. For the first time, melt-blown non-woven fabric was applied for the effective uptake of compounds released from vaporized e-liquid. The extraction procedure was optimized in terms of type of extraction solvent, amount of sorbent and solvent volume. For optimization, a model e-liquid containing flavour additives belonging to various chemicals group with various chemical properties was investigated. The aerosol trapping efficiency was satisfactory and was equal to 92 ± 7%. Final determination was performed by GC-MS/MS. Quantitation was based on the mass change tracking approach (MCT), which assumes the monitoring of e-liquid mass changes before and after vaping. The combination of non-woven fabric and sampling approach (MCT) was proven to be effective in acquisition of reliable data. Thus, the concentrations in aerosol and emission factors were calculated for aerosols collected during the vaping of both model e-liquids and real samples. Validation was performed by evaluating key analytical parameters, such as linearity, accuracy, precision, limit of detection (LOD) and quantitation (LOQ). For all investigated compounds, recoveries from 70% to 118% together with precision and reproducibility below 12% were achieved. The applicability of the described approach was examined by analysing EC refill solutions commercially available on the Polish market.

Microstructural analysis of melt-blown nonwoven fabric by X-ray micro computed tomography

The structures of melt-blown nonwoven fabric, including the fiber volume fraction and fiber orientation, are decided by the melt-blowing conditions, such as the die-to-collector distance (DCD), air suction and air flow rate. In this study, the effects of these melt-blowing conditions on the structure of melt-blown fabric was investigated by X-ray micro computed tomography with a resolution of 1 µm/voxel and a measurement area of 1 mm2. The structural profile along the thickness direction of the fabric was also analyzed. Obtained averages of fiber diameter and basis weight were almost identical to the results of scanning electron microscopy measurements and tests following the standard of International Organization for Standardization. Samples produced with insufficient air suction showed larger deviation of basis weight on the 1 mm2 scale compared with those produced with sufficient air suction. The fiber volume fraction changed steeply around the fabric surface, which was attributed to surface roughness. Insufficient DCD increased the fiber diameter and surface roughness, and decreased the thickness of the fabric. The fiber volume fraction gradually decreased from the collector side to the die side for fabrics with sufficient DCD. The fibers were oriented along the machine direction rather than the cross-machine direction for all layers and samples, and orientation profiles corresponded to the zero-span tensile strength of corresponding samples.

Effect of Bicomponent Fibers on Sound Absorption Properties of Multilayer Nonwovens

In this study sound absorption properties of multilayer nonwovens with bicomponent fibers have been derived compared with homocomponent fibers. Multilayer nonwovens obtained by polyester fibers consisted of three layers. The top and bottom layers were spunbonded nonwoven and middle layer was meltblown nonwoven sandwiched between them. Each layer was produced separately to compose unbonded three-layered nonwoven structures. Four different spunbonded nonwoven fabrics having a basis weight of 40 gsm made from four different polyester cross-sectional fibers (homocomponent round and trilobal, bicomponent round and trilobal). Five different meltblown nonwoven fabrics having five different basis weights ranging 100 gsm to 200 gsm were made from polyester round cross-sectional fibers. Spunbonded/ Meltblown/ Spunbonded (SMS) type unbonded multilayer nonwovens had basis weights ranging 180 gsm to 280 gsm. The effect of basis weight on sound absorption performance of multilayer nonwovens has been evaluated in the study. All results have been analyzed statistically. Results show that three-layered nonwoven structures including bicomponent fibers as outer layers had better sound absorption performance than nonwoven structures including homocomponent fibers. This effect becomes more significant as the basis weight increases, resulting insound absorption coefficients.