Thermal Energy Storage Medium Research Articles

Computational Analysis and Experimental Investigation of the Performance of an Evacuated Tube Solar Air Heater Incorporating Therminol‐55 as a Thermal Energy Storage Medium

Computational Analysis and Experimental Investigation of the Performance of an Evacuated Tube Solar Air Heater Incorporating Therminol‐55 as a Thermal Energy Storage Medium

New database of sustainable solid particle materials to perform a material-based design for a thermal energy storage in concentrating solar power

Renewable energies have surged worldwide, aiming to mitigate greenhouse gas emissions and reduce dependence on fossil fuels. Concentrated solar power (CSP) with thermal energy storage (TES) emerges as a viable alternative to bridge the gap between renewable energy generation and consumption. However, existing CSP plants face a significant challenge in optimizing performance due to the operational temperature limitations of solar salt. While alternative materials, such as solid particles for sensible heat storage in solar towers exceeding 600 °C, have been proposed, the crucial aspect revolves around selecting a new alternative sustainable low-cost material for use as a TES media. This article investigates the optimization of CSP-TES systems by evaluating alternative sustainable low-cost materials sourced from several sectors such as the mining or metallurgical industry, municipal solid wastes, or demolition wastes. The materials, either used in their original form or formulated into aggregates for mortars, underwent thorough a property comparison focused on thermal, physical properties, and cost. With this data, a database was created using the Constructor software from ANSYS and integrated with the Selector software from the same company that provides instrumental for the creation of a comprehensive repository of sustainable materials, providing a database that serves as a practical reference guide for optimizing the selection of sustainable materials as TES in CSP plants. Then, a baseline could be established for selecting a sustainable material for a specific design, considering the properties of the materials. This methodology consists of redesigning and adapting the system according to the material, and it is known as the Materials-Based Design (MBD) process.

Experimental enhancement study of thermophysical properties of ternary carbonate phase change material with multi-dimensional nanoparticles

Carbonates have great application potential as heat transfer and thermal energy storage media in the development of future phase change materials. This paper gives thermophysical properties enhancement study on ternary carbonates in liquid state by adding aluminum oxide nanoparticles, multi-walled carbon nanotubes, graphene nanosheets, and experimentally evaluate the performance strengthen ability of multi-dimensional nanoparticles. The thermal diffusivities and specific heats of the prepared samples by the water solution method are determined using the laser flash technique and the differential scanning calorimetry at liquid state, respectively. A thermogravimetric analyzer is deployed for evaluate the high-temperature thermal stability of the composite ternary carbonates. Scanning electron microscopy and Fourier transform infrared spectroscopy techniques are utilized to examine the surface morphologies and chemical structures of the samples. The results indicate that there is a cooperative reinforcement impact on the thermophysical properties of ternary carbonate by utilizing zero-dimensional Al2O3 nanoparticles and two-dimensional graphene nanosheets, with a maximum improvement of 56.7 % for thermal conductivity, and 10.3 % for specific heat, which is apparently larger than adding any single nanoparticle. The composites exhibit superior thermal cycling stability after low-high temperature experiment, and samples can maintain thermal stability until 700 °C in the thermogravimetric analysis.

Experimental investigation of major rocks in Hong Kong as potential sensible thermal energy storage medium

Energy storage is considered a viable solution for managing renewable energies, and rock is recognized as an economically feasible and environmentally friendly medium for sensible heat storage. Following the principle of utilizing local resources, fifteen major rock types from Hong Kong—covering igneous, sedimentary, and metamorphic classifications—were collected and processed to required sizes for several characterization techniques, considering their heterogeneity and anisotropy. Thermophysical (thermal diffusivity/conductivity, heat capacity, and thermal expansion coefficient) and mechanical properties of the selected rocks were analyzed from room temperature to 1000 °C, along with their chemical and structural compositions. Through multidimensional evaluation, the suitability (optimal, average, poor) of these rocks from Hong Kong to serve as thermal energy storage media was assessed. The results obtained indicated that Hong Kong basalt is the optimal candidate for high-temperature thermal energy storage material, with 850 °C identified as the suitable maximum working temperature. Other igneous rocks from Hong Kong can be utilized for mid-to-low temperature range (100–500 °C) thermal energy storage engineering. However, sedimentary and metamorphic rocks from Hong Kong appear unsuitable for local thermal energy storage engineering.

Effect of Na2CO3 content on thermophysical properties, corrosion behaviors of KNO3-NaNO2 molten salt

Molten salt is popularly used as high temperature heat transfer and thermal energy storage medium. In order to decrease the melting point and increase decomposition temperature of molten salt, phase diagrams for KNO3-NaNO2 binary nitrates were calculated. And the binary salt with the lowest eutectic point was prepared. Furthermore, the effect of Na2CO3 addition on optimal selected KNO3-NaNO2 binary molten salt thermophysical properties and corrosion behavior are experimentally investigated. The results show that the addition of 7 wt% Na2CO3 to KNO3-NaNO2 binary molten salt can lower the melting point by 5.8 %. The addition of 9 wt% Na2CO3 to KNO3-NaNO2 binary molten salt can increase the decomposition temperature by 20.6 %, enhance the specific heat capacity by 4.8 % and increase the thermal conductivity by 7.5 %, but at the same time viscosity increased about 70 % at 300 °C. Meanwhile, the density increases with the increase of Na2CO3 content addition. The average corrosion rate of 316 stainless steel increases with the increasing of Na2CO3 content, which is consistent with the cross-section SEM results.

Heat release efficiency Betterment inside a novel-designed latent heat exchanger featuring arc-shaped fins and a rotational mechanism via numerical model and artificial neural network

Thermal energy storage (TES) units featuring phase change materials (PCMs) have a crucial impact on efficient energy management. Since energy demands keep changing, and the world increasingly relies on sustainable energy sources, innovation is continuously required. New technologies, materials, and methods for energy storage must be developed to meet these shifting needs effectively. In this study, a triplex-tube heat exchanger (TTHE) was employed as a TES medium, utilizing PCM within the middle tube. Because of its high thermal energy storage capacity, RT50 was selected as the PCM. Four innovative arc-shaped fins were strategically integrated within the PCM space to accelerate heat release. The system was subjected to rotational speeds of 0.1, 0.3, 0.5, 1, and 1.5 rpm. The investigation was carried out in two stages: initially, the impact of varying rotational speeds on the discharging process of the PCM in a finless TTHE was explored; subsequently, the influence of the same speeds on the solidification behavior of the finned TTHE was analyzed. Natural convection and PCM’s solidification process were examined through the enthalpy-porosity method. The findings represented that in the absence of fins, the device’s rotation had a more noticeable impact on the solidification behavior; however, incorporating fins was much more influential. Up to 2850 s, all the finned systems had solidified entirely in the presence or absence of the rotational mechanism, while in the finless system with a rotational speed of 1.5, 30.52 % of the material was still unsolidified until this time. Finally, the influence of three key structural parameters of the fins: α (outer fins arc angle), β (inner fins arc angle), and S (space between fins) on the discharging time of the PCM was analyzed using an artificial neural network (ANN) model. The study offered critical insights for optimizing fin configuration by systematically varying these parameters within defined ranges. An ANN predictive model was also proposed to assist TES system manufacturers and developers in future design and optimization efforts. The results demonstrated that the optimal setting of the TTHE (with the parameters of α = 60°, β = 60°, S = 10 mm) achieved the liquid fraction of 0.1, 80.33 % faster than the finless system.

Performance of solid particles as thermal storage media in thermal power flexibility retrofits: Effects of charging and discharging flow rates on single piece stacking bed

An innovative, efficient, and cost-effective energy storage method was introduced for retrofitting thermal power plants, which can be connected in series to scale up quickly (like a battery) and aimed to replace expensive, hazardous molten salts. Charging/discharging processes among steam and solid particles were investigated using energy storage devices with capacities in the tens of kilowatts. Results of the study confirm the excellent performance of steel waste as a thermal energy storage medium. Key findings include that the time required for complete charging decreases from 75 to 300 kg/h, taking 173, 128, 106, and 105 min, respectively. The most efficient charging occurs when the bed temperature is most inhomogeneous, taking 68, 42, 34, and 28 min for 75–300 kg/h. The highest average charging power and heat transfer coefficient are 5 kW and 210 W/(m2·K) at 300 kg/h. In addition, 145 kg/h achieves optimal speed and quantity coupling, resulting in the highest charging efficiency of approximately 84 %. Time-optimized and efficiency-optimized charging flows are given. Real-time efficiency shows that the poorest temperature uniformity corresponds to the highest charging efficiency, with 145 kg/h exhibiting the strongest thermal inertia and 75 kg/h the weakest. Higher flow rates improve internal heat transfer and reduce stratification, facilitating multiple charge-discharge cycles. At discharge rates of 50, 75, and 100 kg/h, steam production is sustained at approximately 30, 40, and 50 kg/h for 11, 7, and 7 min, respectively. Discharge efficiency increases with flow rate, rising from 30 % to 95 %. Phase transition region migrates at approximately 10∼20 mm/s across different discharge rates, with 75 kg/h showing the fastest discharge state. As the discharge rate increases, the phase transition region's total area proportion rises, reaching about 70 % at 100 kg/h. Research demonstrates the potential of this new energy storage medium for efficient and safe retrofitting of thermal power plants.

Enhancing Thermal Conductivity of Phase Change Materials Using Nanomaterials and its Effectiveness in Cooling Solar Cells

The latent heat storage system is considered the most promising technology in thermal energy storage (TES) because of its many advantages. This technique uses phase change material (PCM) as a TES medium. However, the low thermal conductivity (TC) of PCM is the major drawback of the system. Previous studies have shown that the addition of nanomaterials to PCM generally increases its TC. On the other hand, researchers tend to study the possibility of using enhanced PCM to cool solar cells. In fact, raising the solar cell’s operating temperature negatively impacts its efficiency. This problem is considered one of the biggest problems in solar energy systems, and researchers are still working to solve it. This paper focused on the possibility of enhancing the TC of paraffin by adding different shapes of silver nanomaterials to it (silver nanoparticles, silver nanowires and nanohybrid with silver nanoparticles and silver nanowires). Nanomaterials were added at volume fractions of 0.5% and 1%. Then, the study examined the ability to use this improved material to reduce the temperature of solar cells. We used the “Solidworks” program to create a 3D system, and then we used the “Ansys Fluent” software to simulate five cases; PV without PCM, PV with PCM, PV with PCM enhanced by nanoparticles, PV with PCM enhanced by nanowires, PV with PCM enhanced by nanohybrid (a mixture of nanoparticles and nanowires). The results show that using PCM enhanced by nanowire at a volume fraction of 0.5% gave the best results in decreasing the temperature of PV. The average temperature of PV declined by 14.9[Formula: see text]. In addition, the efficiency of PV rose by about 7.6%. Followed by using PCM enhanced by nanoparticles at a volume fraction of 1%. The average temperature of PV declined by 12.9[Formula: see text]. Moreover, the efficiency of PV rose by about 6.6%.

Simulation on solidification process of molten salt-based phase change material as thermal energy storage medium for application in Stirling engine

Abstract Thermal energy storage technologies have been widely used to mitigate intermittency from renewable energy such as solar energy. Phase change material (PCM) is a certain material that can be used as a heat storage medium and is available in a wide range of operating temperatures. Molten salt is one of the PCMs that has the advantage of a very high operating temperature. The PCM solidification simulation based on HitecXL molten salt using COMSOL Multiphysics software will be carried out with variations in heat absorption of 1 - 5 kW/m2, assuming constant heat absorption. The results show that the PCM solidification process starts from the surface of the Stirling engine heat exchanger pipe. The part of the PCM that has been solidified will fall following the direction of gravity and cause a phenomenon such as a droplet. The flow that occurs is a natural flow caused by the buoyancy force due to changes in density due to temperature gradients in the solidification process. The time required for the PCM to completely solidify is closely related to the amount of heat absorption. The greater the heat absorption from the pipe, the faster the PCM to fully solidified.

Viability of hybrid and alkali-activated slag materials for thermal energy storage: Analysis of the evolution of mechanical and thermal properties

Technological progress is needed to develop renewable energies. Improvements should be especially focused on the energy storage element to help correct the mismatch between energy supply and demand. In concentrated solar power (CSP) plants, ordinary concrete made of Portland cement (PC) has been proven to be a good thermal energy storage (TES) medium. However, the substantial environmental impact of PC manufacturing makes it necessary to develop new materials. Thus, in this work, alternative alkali-activated mortars (AAM) and hybrid materials (HM) have been developed using blast furnace slag to replace PC. This has been done in order to study their stability at high temperature (up to 500 °C) and their viability to operate as TES, undergoing thermal cycles between 200 °C and 400 °C, as they would in CSP technologies. Studying the mechanical and thermal properties after the thermal treatments has revealed that the alternative materials offer improved mechanical properties as well as very good thermal conductivity and storage capacity values. In particular, the best results in terms of mechanical properties were achieved by the AAM system, where the compressive strength value is increased with respect to the reference PC sample by 195% after exposure to 500 °C and by almost 97% after 20 thermal cycles between 200 °C and 400 °C. Furthermore, in terms of thermal properties, the AAM system showed a 31% increase in thermal conductivity after thermal exposure compared to PC. In addition, both AAM and HM systems demonstrated substantial improvements in specific heat and thermal storage capacity, outperforming PC by up to 46% during CSP-like thermal cycles. These promising results open new doors to the study of these alternative materials, such as TES, as they are more suitable than PC from an operational point of view.

Influence of Different Melting Points of Phase Change Material on Photovoltaic Phase Change Materials System Performance: An Energy, Exergy, and Environmental Point of View

The photovoltaic (PV) module extracts and converts solar irradiation energy into electrical power in a sustainable and renewable manner. The substantial upswing in the temperature of the PV panel occurs while conversion predominantly impacts its performance and reduces efficiency. To resolve this issue, three different organic phase‐change materials (PCMs), OM29, OM35, and OM42, are proposed for cooling the PV panel as a thermal energy storage medium. The energy and exergy performance of PV panels with and without PCM are compared through experimental investigation to study the influence of different melting points of PCM with reference PV system (PVr). It is identified that the average PV panel temperature can be significantly reduced by incorporating PCM materials (OM29, OM35, and OM4), which are 12.7%, 21.53%, and 17.71% lower than the PVr system. The average electrical efficiencies of PV‐PCM–OM29, PV‐PCM–OM35, and PV‐PCM–OM42 are 10.96%, 10.77%, and 11.66%, which are 4.07%, 6.38%, and 4.91% higher than PVr system. Similarly, the average exergy efficiency is 4.62%, 5.06%, and 5.57% higher. The incorporation of PCM (OM29, OM35, and OM4) as a cooling mechanism effectively mitigates the CO2 3.70, 5.67, and 4.46 tons of CO2 throughout its lifetime and contributes to the sustainable development goal 7.

Predicting thermophysical properties of molten salts in the MgCl2-NaCl-KCl-LiCl system with a shell-model potential

Ternary eutectic salts composed of MgCl2, NaCl, and KCl, referred to as MNK salts, have recently emerged as promising candidates as high-temperature heat transfer fluids and thermal energy storage media. In this study, we performed classical molecular dynamics (MD) simulations to predict the densities, specific heat capacities, viscosities, and ionic self-diffusivities for MNK salts over a wide temperature range. The impact of LiCl additive on their thermophysical properties was also investigated. To capture the electronic polarization of Cl anions by neighboring cations, we developed a novel shell-model potential using the force-matching method and a dataset of ab initio calculated interatomic forces. Our extensive MD simulations predict structure and properties for pure salts and binary/ternary salt mixtures in the MgCl2-NaCl-KCl-LiCl system in overall good agreement with available experimental and theoretical data, which corroborates the accuracy and reliability of our developed potential.

Dynamic Modeling of a Concentrating Solar Thermal Plant With a Packed Bed Energy Storage

The Air-packed bed system is a cost-competitive concentrating solar thermal system that employs air as the heat transfer fluid and a solid packed bed as the thermal energy storage medium. The thermocline behavior of the packed bed plays an important role in the performance and operation of the system, so a dynamic model of the TES is needed to evaluate the design and performance of the system. A high-fidelity first-principle TES model is often too computationally expensive to incorporate into a larger system model for simulation and optimization at an annual time scale. Here, we develop in Modelica a system model for a CST concept plant with a reduced order TES model to ensure the necessary thermocline fidelity while maintaining suitable computational performance. The validity of the reduced order model is quantified both against simulation results from a first-principle finite-difference model and against real-world test data taken at the Heliogen Test Facility in Lancaster, CA. The thermocline fidelity and computational performance of the system model are then demonstrated with an annual simulation run of the concept air-packed bed plant.

Electrochemical impedance study of corrosion of pure Ni, Fe, Cr, and Fe‐5Cr alloy in molten nitrides

AbstractMolten nitrates or nitrate–nitrite mixtures have been used as heat transfer fluid as well as thermal energy storage medium in concentrated solar power plants and other industrial applications. However, containment materials in contact with these molten salts are subjected to molten salt corrosion, which has been a concern over the years. In this investigation, the corrosion behavior of pure Ni, Fe, Cr, and Fe‐5Cr alloy (in weight percent) has been examined at 400°C in molten nitrates using electrochemical impedance spectroscopy and gravimetric tests. It is shown that Ni, Fe, and Fe‐5Cr exhibit mass gain, with the best corrosion resistance for Ni followed by Fe‐5Cr and Fe, while pure Cr goes through fast dissolution, forming hexavalent chromium product K3Na(CrO4)2. The increase of salt basicity from Solar Salt to Hitec could accelerate the dissolution of Cr. Nevertheless, the formation of an inner Cr‐containing scale could still offer the alloy good protection because the external insoluble Ni or Fe oxides can protect it from dissolution.

Flexible insulating phase change composite film with improved thermal conductivity for wearable thermal management

Phase change materials (PCMs) are extensively employed as media for thermal energy storage and temperature regulation due to their remarkable capacity to absorb or release significant amounts of latent heat at constant phase transition temperatures. However, the inherent low thermal conductivity, solid-state rigidity and electric insulation issues of PCMs greatly limit their practical applications in the field of wearable thermal management of flexible electronic devices. Herein, we have developed a flexible composite PCM film with improved thermal conductivity by incorporating paraffin wax (PW) with a porous structure of polyvinylidene fluoride-boron nitride (PVDF-BN) film as a substrate. Remarkably, the composite film exhibits outstanding electric insulation properties and excellent cycle stability, further enhancing its suitability of thermal management in wearable electronics for safe and long-term applications. The obtained flexible composite PCM film exhibits a superior melting enthalpy of 105.63 J·g−1, along with a 200% improvement in thermal conductivity compared to the pure PW. Furthermore, this flexible composite film can not only retain its remarkable flexibility at room temperature but also demonstrate attractive shape recovery capabilities during phase transition process. The flexible insulating PCM film developed in this work may hold substantial promise for applications in the field of wearable thermal management for next-generation electronic devices.

Thermal Stability and Performance Evaluation of Hitec Molten Salt for High-Temperature Energy Storage Applications

The quest for advanced materials in thermal energy storage (TES) has become paramount in a world grappling with pressing demands for sustainable and reliable energy solutions. Among these materials, molten salts have emerged as up-and-coming contenders, owing to their exceptional thermal properties and wide operational temperature ranges. HITEC, a eutectic blend of sodium nitrate, sodium nitrite, and potassium nitrate, distinguishes itself as a superior choice due to its unique amalgamation of favorable thermal characteristics. This comprehensive review delves into the thermal properties of HITEC molten salt and its manifold applications in thermal energy storage, illuminating its potential as a pivotal element in addressing contemporary global challenges. The review examines HITEC's specific heat capacity, thermal conductivity, and thermal stability, presenting critical insights into its efficacy as a TES medium. Such comprehension fosters the advancement of Sustainable Development Goal 7. The article explores strides made in HITEC-based TES systems, underscoring inventive engineering approaches and burgeoning technologies that bolster progress towards Sustainable Development Goal 9. Furthermore, the article discusses challenges associated with HITEC molten salts, such as corrosion and material compatibility issues, and investigates ongoing research efforts to overcome these limitations. A comparative evaluation of HITEC with other molten salt mixtures elucidates its competitive advantages. This review consolidates knowledge about HITEC molten salt for thermal energy storage applications, providing valuable perspectives for researchers, engineers, and policymakers dedicated to advancing sustainable energy technologies. The review underscores the pivotal role of HITEC molten salt in advancing thermal energy storage technologies, directly influencing the achievement of several SDGs.

Graphene oxide – adipic acid nanocomposites for thermal energy storage: Assessment of thermophysical properties and energy storage performance

Adipic acid is one of the organic phase change materials with a melting temperature greater than 150 °C and a freezing point greater than 140 °C, making the same a suitable thermal energy storage medium for near-atmospheric pressure steam generation. This work attempts to alleviate the rate limitation posed by the lower thermal conductivity of adipic acid by adding graphene oxide (GO) nanostructures at lower concentrations such that the energy storage capacity is not severely affected. The resultant GO – adipic acid composites (0–2 wt% GO) were characterized in terms of latent heat for phase change, specific heat and thermal conductivity. The composite containing 1 wt% GO exhibited a 16 % enhancement in thermal conductivity with a 3.4 % reduction in latent heat and 3.6 % reduction in specific heat. The impact of GO addition on the solidification rate was remarkable, with a 44 % enhancement in overall heat transfer coefficient during the initial solidification phase, when solidification was carried out in thermal contact with a constant temperature heat transfer fluid (oil bath). Thus, the present work clearly demonstrates the intensification of heat transfer during the discharge cycle of a thermal energy system with 1 wt% GO-Adipic acid composite as the thermal energy storage medium.

Analysis of heat charging and release processes in cascade phase change materials energy storage floor heating systems: Performance evaluation

To address the issues of high energy consumption, significant temperature fluctuation and low heat release efficiency in conventional energy storage floor heating systems, this study proposes a novel solution known as the cascade energy storage floor heating system. This system incorporates two layers of phase change materials (PCMs) with distinct phase change temperatures as the thermal energy storage medium. A coupled heat transfer numerical model is developed to analyze the heat charging and release processes within the floor heating system. The evolutions of liquid fraction of PCMs, flow field and floor surface temperature are investigated during the heat charging and release processes. The findings demonstrate that the cascade PCM energy storage floor heating system avoids overheating and saves >19 % of energy consumption during the heat charging process, elevates the floor surface temperature by about 2 K during the late stage of heat release and thus reduces floor surface temperature fluctuation in comparison with the single-stage PCM system. These improvements are conducive to enhancing the energy utilization rate. Due to better synergistic solidification of the two PCM layers, the system with a PCM proportion of 1:1 exhibits superior overall heat release performance when compared to systems with PCM proportions of 1:2 or 2:1. The research outcomes provide a theoretical foundation and technical guidance for the practical implementation of cascade PCM energy storage technology in the field of building energy conservation.

Flexible and photo-responsive composite phase change materials for thermal therapy

The medical dressings with appropriate temperature can relieve body pain by promoting blood circulation. In order to endow the thermal compress dressings with multifunction and facilitate their application in different scenarios, the flexible films employing paraffin (PF) as thermal energy storage medium, styrene-ethylene/butylene-styrene (SEBS) triblock copolymer as matrix and graphene as photo-thermal conversion agents were fabricated. The film containing 77 wt% of PF has high latent heat of 157.26 J·g−1 and exhibits smooth and dense morphology. The film also exhibits tensile strain of 2576.75 %, photothermal conversion efficiency of 70.52 % and enviable self-healing properties, which makes it possible to meet the needs of different body parts and reuse in practical applications. In addition, under natural sunlight, the thickness of 3 mm thermal film can maintain the temperature ranging from 40 °C to 50 °C for more than 25 min; under the action of an electrically heated film, the film can maintain at 40 °C to 50 °C for about 22 min. The extraordinarily long thermal therapy time and suitable thermal therapy temperature are remarkable. In summary, the excellent thermal storage properties, mechanical properties, self-healing properties and photothermal conversion properties make it a good application prospect for thermal therapy.

Thermal stability and durability of solar salt-based nanofluids in concentrated solar power thermal energy storage: An approach from the effect of diverse metal alloys corrosion

Concentrated Solar Power (CSP) technology has witnessed substantial growth, with forecasts predicting an increase of 3.4 GW between 2019 and 2024. This expansion necessitates the installation of energy storage systems to meet the growing demand. Solar molten salts, specifically a mixture of 60 % NaNO3 and 40 % KNO3, have emerged as the primary thermal energy storage (TES) medium in commercial CSP plants. However, a significant challenge lies in the corrosive nature of molten salt at high temperatures, which poses limitations in TES applications. The literature has explored a promising solution: reducing corrosion rates by incorporating nanoparticles into molten salts, creating nanofluids. To assess the viability of nanofluids for CSP, it is essential to understand how they perform under working conditions, especially regarding their thermal stability and durability. This study presents further evidence of nanofluid interactions with component materials under static working conditions. Specifically, focus on the impact of corrosion products precipitated during corrosion tests on the physical and thermal properties of Solar Salt-based silica dioxide nanofluids. In this research, nanofluids in contact with stainless steel, nickel‑chromium alloy, and carbon steel were examined before and after subjecting them to a 90-day thermal exposure at 500 °C. These findings provide valuable data on key thermo-physical properties during service, contributing to the design of more precise TES systems and enhancing their overall efficiency and effectiveness.