Fracture Mechanics Research Articles

Acoustic emission characteristics of coal and limestone failure based on MFCC

Fractures in the rock surrounding karst caves can result in substantial surface subsidence, especially in mining areas with abundant carbonate rocks. Acoustic emission (AE) is a crucial signal associated with rock fracture mechanics and lithology. This study aimed to distinguish the AE features between coal and limestone using the MFCC-based method and universal AE analysis method in conjunction with uniaxial compression tests. The results indicated that the MFCC-4–6 of AE could distinguish between coal and limestone prior to rock failure. The MFCC-1–6 of limestone exhibited a tail-like pattern change on the stress sawtooth and a step-like pattern change after reaching peak stress. The fluctuation degree of MFCC-2–5 exhibited an initial transition from small to large, followed by a subsequent transition from large to small, reaching its maximum value during the elastic deformation stage. Additionally, the power law distribution index of AE energy in the magnitude range of 102–104 for coal was larger than that for limestone. The AE events in coal were mainly characterized by shear fractures, while limestone exhibited more tension fractures than coal, as indicated by the AF/RA analysis. Furthermore, the lower the AE peak frequency, the larger the scale of fracturing in coal and limestone. These findings are valuable for ground control and early warning of rock failure.

Debonding Fiber Damage Mechanism Modeling for Machining Damage Inhibition During Rotary Ultrasonic Face Grinding SiO2f/SiO2

Abstract The debonding fiber defects on the grinding surface of SiO2f/SiO2 ceramic matrix composites deteriorate the service performance of related components. The low-damage process window is the key information to suppress machining damage by controlling grinding parameters. A mechanism model for debonding fiber damage on SiO2f/SiO2 surface was first proposed in this paper by the large deformation analysis for SiO2 fibers during rotary ultrasonic face grinding (RUFG). The established mechanism model built a bridge between grinding parameters and damage inhibition by integrating the ultrasonic stress effect, grinding force calculation, and critical fracture curvature cutting-off criterion of SiO2 fibers. The modeling mechanism for fiber deformation and fracture in grinding was validated by in situ observation of single abrasive grit scratching experiments. Besides, the low debonding damage process window predicted by the model was verified by experimental results and could be adopted to suppress the debonding fiber damage in grinding. The affected mechanism of fiber orientation, ultrasonic amplitude, and fiber-matrix interface strength on the low debonding damage process window was analyzed based on the theoretical and experimental results. The damage inhibition effect of the RUFG process was limited by the low fiber-matrix interface strength and axial cutter-relieving movement component. The ultrasonic-assisted vibration exerted its auxiliary effects through the ultrasonic stress effect and force reduction effect. The prerequisite for exerting the damage inhibition effect of RUFG was that the fiber-matrix interface strength was sufficient to resist the negative influence of the ultrasonic stress effect.

Propagation Effect Analysis of Existing Cracks in Box Girder Bridges Based on the Criterion of Compound Crack Propagation

Cracking in concrete box girder bridges will have a significant impact on the safety and durability of the structure, and many box girder bridges which are in service have undergone varying degrees of cracking. Currently, the safety design of actual bridge projects place an emphasis on the stress or the load value of a cross section at the limit value specified in the code for safety control. This design method assumes that the member itself is of uniform and continuous material and is internally undamaged. However, the bridge structure is more or less cracked to varying degrees during the period from casting to construction to operation of the concrete members. In this paper, a finite element computational model of a three-span prestressed concrete box girder bridge with existing cracks is established based on the fracture mechanics theory, and the critical parameters of crack extension are introduced to evaluate the extension state of cracks. At the same time, the extended stability of the existing cracks of the box girder bridge is analyzed by considering the temperature effect, vehicle loading, and prestressing loss, and the sensitivity of crack extension under each working condition is investigated. The results show that, with the increase in crack length and depth, the crack expansion is promoted, but the effect is relatively small, and the maximum stress intensity factor is only 6.48 MPa mm1/2. Under the multi-factor coupling effect, the cracks show a composite crack expansion dominated by type I cracks, the longitudinal cracks of the existing base plate are in a stable state, the maximum value of the crack expansion critical parameter of the vertical cracks of the webs reaches 1.087, and there is a tendency to expand locally. The maximum value of the critical parameter for crack extension of the vertical crack in the web plate reaches 1.087, and there is a tendency towards local expansion. The crack extension evaluation criteria proposed in this paper have a certain reference value for crack extension research on similar concrete box girder bridges and provide a scientific basis for the optimized design of similar bridges.

Effect of temperature on the microstructure and mechanical properties of TiC/Fe matrix composites fabricated by spark plasma sintering

The effects of sintering temperatures on the microstructures and mechanical properties of titanium carbide particles reinforced iron matrix composites (TiC/Fe MCs) fabricated by the spark plasma sintering (SPS) process with pure element powders have been systematically investigated. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron back scattering diffractometer (EBSD), and energy dispersive spectroscopy (EDS) have been conducted for microstructural analysis. The results show that with increasing sintering temperatures, the porosity of the composites initially decreases and then increases. Simultaneously, the grain size gradually diminishes while element diffusion becomes more uniform. Upon reaching a critical sintering temperature (1120 °C), the original grain size disappears and carbides undergo decomposition and reprecipitation to reach an equilibrium state, with which optimal comprehensive properties can be achieved (porosity decreases to a minimum of 3.85%, grain size of 2.69 μm, Vickers hardness reaches 595 HV0.5, bending strength is at 662 MPa, coefficient of friction is at 0.74, and wear loss to 0.21 mg). These property enhancements have been attributed to reduced porosity in the composites, decreased grain size, and improved anchoring effect of carbides within the matrix. Additionally, the primary fracture mechanisms and wear mechanisms of TiC/Fe MCs with different process parameters have been analyzed. When the temperature is below 1080 °C, intergranular fracture predominates, whereas transgranular and ductile fractures become predominant above this threshold. When the temperature is below 1120 °C, fatigue wear, oxidation wear, and abrasive wear are predominantly observed. Conversely, when the temperature exceeds 1120 °C, oxidation wear and abrasive wear become the primary mechanisms.

Thermoelastic fracture of two-dimensional hexagonal quasicrystal media weakened by a penny-shaped crack subjected to uniformly antisymmetric heat fluxes

This study focuses on the thermoelastic fracture behavior of quasicrystals, a class of solids that exhibit unique properties between traditional crystals and amorphous materials. The complex atomic structure of quasicrystals poses challenges in understanding their fracture mechanisms under thermoelastic loading conditions. Central to our investigation is an analytical examination of a penny-shaped crack in an infinite three-dimensional body composed of two-dimensional hexagonal quasicrystals, where the upper and lower crack surfaces are applied to a pair of uniformly antisymmetric heat fluxes. This crack problem requires simultaneous consideration of thermal-phason-phonon multiple field coupling. According to the symmetry of field variables with respect to the crack plane, the thermal-phason-phonon coupled crack problem is transformed into a mixed boundary value problem in the upper half space. The extended displacement discontinuities, encompassing both phonon and phason displacement discontinuities, as well as the temperature discontinuity, are chosen as the basic unknown variables to construct the boundary integral-differential equations governing the mixed boundary value problem. Based on these boundary governing equations and Fabrikant's potential theory method, the problem with the crack surface subjected to uniform antisymmetric heat fluxes is solved. The solutions of thermal-phason-phonon fields on the crack plane, and in the full space are given in closed-form. Numerical results are employed to validate the obtained analytical solutions and visually illustrate the spatial distribution of thermal-phonon-phason coupling fields in the vicinity of the crack. The study provides fundamental insights into the behavior of cracks in quasicrystals under thermal loading, with potential implications for the design of new materials and structures.

Penetrative Fracture Behavior of Monolayer Graphene Oxide: Nanoscale Experiment and Molecular Dynamics Simulation

Abstract Graphene, a two-dimensional material, is expected to be employed as a next-generation component for structural and functional applications because of its light weight and excellent mechanical properties. For applications requiring lightness and impact resistance, preventing penetrative damage upon particle impact is critical for applications in mechanical protection. However, graphene is known to have high defect sensitivity. Graphene oxide (GO) may be a better candidate, as functional groups (e.g., hydroxy and epoxy groups) bonded to the C–C network in GO result in better deformability, ductility, and durability compared to graphene. For mechanical applications, it is crucial to understand the fracture behavior, especially the penetrative fracture behavior, of GO membranes. This study characterizes the penetration behavior and fracture morphology of GO membranes subjected to particle impact. Nanoscale experiments were conducted using an atomic force microscope and laser-induced particle impact test for GO. These material testing methods employ nanoscale spheres to induce particle penetration, with the former experiment conducted under quasi-static loading and the latter under dynamic loading. Additionally, molecular dynamics simulations were performed to elucidate the fracture mechanisms of GO. Finally, cyclic fatigue experiments and simulations revealed that GO’s ductility provides resistance to catastrophic failure, indicating its durability. These comprehensive investigations provide valuable insights into the fracture properties of GO membranes under impact penetration.

Crack-tip cleavage/dislocation emission competition behaviors/mechanisms in magnesium: ALEFM prediction and atomic simulation

Structural properties and reliability of materials can be improved by increasing fracture toughness. At the atomic scale, the fracture is a material separation process, and the fracture toughness of materials is associated with the atomic-scale crack-tip behaviors/mechanisms. The crack-tip behaviors are relevant to the energy state of atoms in the system. Atomic thermal oscillation increases with increasing temperature, which may affect/alter the crack tip behaviors. This work is the first to investigate the temperature-dependent crack-tip cleavage/dislocation emitting competition in magnesium (Mg) using anisotropic linear elastic fracture mechanics theory, Density Functional Theory (DFT), and atomic simulation. Crack-tip behaviors are examined using a specially designed ‘K-field’ loads model. DFT calculations show that a single crystal system with lower entropy and higher Gibbs free energy implies stronger interatomic bonding that favors a higher KIc. Changes in the stress distribution initiate a brittle-ductile transition in crack-tip behavior. The ductile crack tip can be blunted by continuous crack-tip dislocations nucleation/slip, and the evolution of the ductile crack-tip geometry from sharp to semicircular structure significantly decreases the stress concentration at the crack tip. A new criterion of the crack-tip force vector is established, which reasonably explains the geometrical evolution of ductile crack tip where the angle θ between the crack plane and the slip plane is 0∘<θ<90∘ and θ=90∘. This work expands the atomic-scale brittle/ductile crack-tip behaviors/mechanisms of Mg, which provides a reference for crack-tip behavior analysis in engineering research.

Mechanical Properties and Microstructure Analysis of Mild Steel Welding Made by GTAW

This work discusses the effect of gas tungsten arc welding (GTAW) variables on the welding transverse tensile strength and hardness of S 235JR at different groove configurations. The welding microstructure and numerical fracture mechanism are also discussed. GTAW is increasingly emerging in the local industry due to its advantages over conventional shielded metal arc welding (SMAW). The properties of steel welding have always concerned manufacturers and researchers. Since steel structures experience forces such as tensile, it’s vital that good welding has increased tensile strength. It was reported that the hardness of welding affects the welding properties and, therefore, the integration of welded structures. The groove shape of the joining ends determines the size of the FZ and affects the dilution; thus, it is important to study the groove shape due to its effect on the final properties of welding. The results showed an increased welding traverse tensile strength (251 MPa) at higher welding speeds (150 mm/min) and V-shaped groove welding. The V-shaped groove welding that obtained higher tensile strength (251 MPa) has shown higher grain boundary ferrite and PF volume friction in the FZ and finer PF in the HAZ due to its higher interpass heat input. Higher traverse tensile strength welding has shown increased bainite and lower bainite volume friction in FZ and a finer grain structure in HAZ. The failure due to tensile force starts at the welding root, according to numerical analysis, and a double V-shaped groove has shown deformation balance at the tensile test.

Investigating dwell fatigue crack growth in welded titanium alloy structures

ABSTRACT In this paper, dwell-fatigue crack growth tests under complex loading spectra were conducted for a titanium alloy used in marine structures. The influence of upper and lower peak dwell time on the dwell-fatigue crack growth behavior of the welded structure were comprehensively investigated. The results show that the longer the upper and lower peak dwell times were, the faster the crack growth rate was. Still, the impact of the upper and lower dwell times on the crack growth rate of titanium alloy had a specific saturation value. Based on the above findings, a new model was developed that combined the fracture mechanics theory, considering the effects of welding and load dwell on crack growth. By predicting the dwell-fatigue behavior of titanium alloy welded structures using the model, it was confirmed that the model has a strong prediction ability for the dwell-fatigue behavior of welded structures under complex loads..

The effect of direct aging treatment on microstructure and mechanical properties of the GH4099 superalloys produced by selective laser melting

The effect of direct aging (DA) treatment on microstructure and mechanical properties of the GH4099 superalloys produced by selective laser melting (SLM) was investigated by the microhardness tests, room- (RT) and high-temperature (HT) tensile tests, field emission scanning electron microscopy (FE-SEM), and electron backscattered diffraction (EBSD) in this study. Both microhardness and RT tensile results show that DA treatment improves mechanical properties more than solution-aging (SA) treatment. By analyzing the effect of the microstructural features on the yield strength, we found that the dominant strengthening mechanisms responsible for higher yield strength of the DA specimens are the grain size hardening of fine γ matrix, high-density dislocation strengthening, Orowan dislocation bypass strengthening of smaller but dense M23C6-type carbides, and chemical strengthening of smaller but dense γ΄ nanoprecipitates. Furthermore, a transgranular fracture is a dominant fracture type for RT tensile specimens produced by DA treatment. Conversely, the failure type of SA tensile specimens is a typical intergranular fracture mechanism. The underlying mechanism for the above phenomenon is attributed to the effects of transgranular and intergranular M23C6-type carbides.

In Silico Investigation of the Interlaminar and Mechanical Fracture of Arteries with Atheromatic Plaque during Angioplasty Treatment

The reduction in the inner diameter of the artery due to the creation of atheromatic plaque on the artery lumen, known as artery stenosis, disrupts the blood flow, leading to medical complications, which can be fatal. The angioplasty procedure aims to reopen the artery and uses a stent to keep it open. In this study, an effort is made to determine the point of the stent, the plaque and the artery during the expansion phase of the angioplasty using the in silico Finite Element Analysis method. A literature-based design was chosen for the stent geometry, whereas simplified shapes of the balloon and the two artery layers were used. Additionally, two plaque designs were the benchmark for the eight distinct artery stenosis models within the Abaqus environment. In the context of stent angioplasty simulations, failure patterns were investigated. An inverse relationship was observed between artery stenosis and pressure at the artery failure point, while an increased danger of interlaminar failure was detected in models with larger artery stenosis. This study verifies the necessity for the inclusion of interlaminar failure in future angioplasty research.

Surface roughness and fracture cracks of Al2O3/TiO2 composite coating by wet chemical mechanical grinding with structured abrasives pad

In the fields of wind power, and other industries, the Al2O3/TiO2 coating is prepared and ground on the bearing ring, in order to obtain the insulation resisting the electrical erosion for the motors at high voltage. A novel wet chemical mechanical grinding (WCMG) method is proposed to finish this hard-brittle composite material, utilizing the structured diamond abrasives pad and the NaOH solution. The softened workpiece's surface under the chemical reaction was demonstrated by means of Raman spectrum, indentation and scratching tests. The analytical model of surface roughness and fracture cracks is established based on the synthesis of geometry and kinematics, contact mechanics, material removal and indentation fracture mechanics. The surface roughness of coating was reduced from initial Sa 3.293 μm down to final Sa 0.049 μm in the WCMG process with grain size 3 μm and pH 12.01, mostly attributed to the ductile removal of chemically softened coating surface.

Effect of grain size on the deformation mechanism and fracture behavior of a non-equiatomic CoCrNi alloy with low stacking fault energy

Manipulation of stacking fault energy (SFE) plays a significant role in microstructure control and in turn mechanical properties of advanced alloys. In this work, we present the influence of grain size on the mechanical properties and fracture behavior of a non-equiatomic CoCrNi alloy with low SFE. Specimens with controlled grain sizes ranging from 0.61 to 6.4 µm were fabricated through rolling and annealing. A novel SFs-dominated plastic deformation mechanism was discovered. Tensile strength decreases monotonically with increasing grain size, while ductility achieves a peak value at the medium grain size, contradicting with the typical behavior observed in most single-phase face-centered cubic (FCC) metallic materials deformed primarily by dislocation slips and/or twinning. The fracture behavior changes from void coalescence to quasi cleavage with grain coarsening, and the fracture mechanisms were analyzed. Additionally, the evolution of SFs and phase transformation is explored at various deformation strains.

Microstructural behavior of CNT-PDMS thin-films for multifunctional systems

Heterogeneous ribbed and non-ribbed carbon nanotube (CNT)-PDMS thin-film systems manufactured by large-scale rolling exhibit large-strain and high strain-rate characteristics with favorable surface behaviors, such as superhydrophobicity and drag reduction. However, it is not well understood how the multi-phase microstructure and material properties of non-ribbed thin-films are related to the surface material behavior and fracture. Hence, the objective of this investigation is to characterize the large-strain mechanical behavior and the microstructure of various CNT-PDMS compositions to understand how the CNT loading, agglomeration, distribution, and orientation affect the mechanical behavior and fracture of CNT-PDMS unribbed systems. Non-ribbed thin tensile testing specimens were fabricated for neat PDMS and CNT-PDMS with different weight CNT distributions to understand non-ribbed behavior. The ultimate strain, strength, and global stress–strain behavior were obtained by uniaxial mechanical testing. Scanning electron microscopy (SEM) of the fracture surface was also obtained for each sample to analyze the microstructure and relate the damage mode to the different weight distributions. Based on these experimental measurements and observations, large-strain, hyperelastic and hyper-viscoelastic material models were used to characterize the material behavior. The hyper-viscoelastic material model was shown to provide the most accurate material description of the thin-film behavior of the viscoelastic PDMS with the high-strength CNTs.

Fracture Behavior of a 2D Imine-Based Polymer.

2D polymers have emerged as a highly promising category of nanomaterials, owing to their exceptional properties. However, the understanding of their fracture behavior and failure mechanisms remains still limited, posing challenges to their durability in practical applications. This work presents an in-depth study of the fracture kinetics of a 2D polyimine film, utilizing in situ tensile testing within a transmission electron microscope (TEM). Employing meticulously optimized transferring and patterning techniques, an elastic strain of ≈6.5% is achieved, corresponding to an elastic modulus of (8.6 ± 2.5) GPa of polycrystalline 2D polyimine thin films. In step-by-step fractures, multiple cracking events uncover the initiation and development of side crack near the main crack tip which toughens the 2D film. Simultaneously captured strain evolution through digital image correlation (DIC) analysis and observation on the crack edge confirm the occurrence of transgranular fracture patterns apart from intergranular fracture. A preferred cleavage orientation in transgranular fracture is attributed to the difference in directional flexibility along distinct orientations, which is substantiated by density functional-based tight binding (DFTB) calculations. These findings construct a comprehensive understanding of intrinsic mechanical properties and fracture behavior of an imine-linked polymer and provide insights and implications for the rational design of 2D polymers.

Multiscale study of dynamic mode-I fracture characteristics of thermally treated granite: Comparison of conventional and microwave heating

High-temperature-assisted rock breaking is a promising technique, with conventional and microwave heating being widely used methods. Understanding the mechanisms of conventional and microwave heating on the dynamic mode-I fracture characteristics of rock is crucial for engineering applications. Dynamic mode-I fracture experiments were conducted on Notched Semi-Circular Bending (NSCB) specimens at 25, 200, 300, 400, and 500 °C under both heating methods. Additionally, a finite element-discrete element coupled numerical method was developed to simulate the dynamic mode-I fracture process in high-temperature granite. The study investigated the effects of both heating methods on the fracture process and morphological features of the rocks, revealing differences in damage mechanisms across various scales. Results indicated that both heating methods similarly influence the fracture toughness of granite, with fracture toughness initially remaining nearly unchanged and then rapidly decreasing, with 200 °C identified as the threshold temperature. Moreover, the fractal dimension increased exponentially with temperature. The fracture mechanisms associated with conventional and microwave heating were also discussed.

On microstructures and mechanical properties of automotive (Graphtie-TiB2)/Cu composites with different milling times

Copper (Cu) matrix composites are the most attractive materials in rail transit, aerospace and other fields because of their excellent electrical conductivity and strength. The aim of this study was to determine the effect of milling time on the microstructure and mechanical properties of the (Graphtie-TiB2)/Cu composites. The composites were prepared using rapid hot pressing sintering at the milling time of 4, 6, 8, 10 and 12. The structural, physical and mechanical properties of the composites was characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and compression test. The results revealed that the particles size decreased with an increase in milling time, especially the particles size drop sharply during the first 4 h of milling, and the particles size directly decreased from 44.3 μm to about 13.2 μm. The full width at half maximum of diffraction peak increased gradually with an increase in milling time. The relative density, hardness, elastic modulus, electrical conductivity and compressive strength of the composites reached the maximum at 6 h, which were 99.1 %, 86.6 HV, 137.1 GPa, 45.6 %IACS, and 228.8 MPa, respectively. Compared with 12 h, the hardness, electrical conductivity and compressive strength at 6 h were increased by 5.7 %, 79.4 % and 56.9 %, respectively. Finally, the fracture mechanism of the composites was analyzed by observing the fracture morphology.

Fracture Mechanisms and Crack Propagation in Monolayer Ti3C2Tx under Nanoindentation: The Influence of Surface Terminations and Vacancy Defects.

Monolayer MXenes are a novel class of two-dimensional transition metal carbides/nitrides with fascinating physicochemical properties. Despite recent advances in the study of MXenes' mechanical properties, a comprehensive understanding of the fundamental physical mechanisms that affect fracture due to surface terminations and vacancy defects in MXenes under nanoindentation remains largely unexplored. Here, we address this gap using molecular dynamics simulations and nanoindentation theory to investigate the effects of surface terminations and vacancy defects on the fracture behavior of Ti3C2Tx MXenes. By inducing the rupture of monolayer MXenes through nanoindentation, we find that bare Ti3C2 exhibits brittle fracture behavior. The presence of surface terminations and vacancy defects reduces the load-carrying capacity and flexibility of MXenes. Interestingly, surface terminations increase the stiffness of the structure, while vacancy defects have the opposite effect. We also find that high concentrations of surface oxidation impart ductile fracture characteristics to MXenes and increase the maximum crack length at failure. Additionally, defects exceeding the critical concentration can effectively prevent brittle crack propagation by causing frequent crack deflection and blunting crack tips. Combining these findings, we propose a new strategy to synergistically enhance the fracture toughness of MXenes through high concentrations of surface oxidation and vacancy defects exceeding the critical concentration without significantly affecting strength and stiffness, thereby avoiding catastrophic failure in MXene monolayers due to brittle fracture. This work provides fundamental insights into the mechanical properties and fracture mechanisms of monolayer MXenes.

Dynamic fracture mechanism and fragment characteristics of sandstone specimens with asymmetrical conjugate fissures under static pre-compression

This paper systematically investigates the dynamic mechanical response and fragment characteristics of sandstone with asymmetrical conjugate fissures subjected to preexisting static stress based on the split Hopkinson pressure bar apparatus. The cross-fissured sandstone exhibits significant variations in mechanical behavior when exposed to higher dynamic strain rates under identical static pre-stress. The cross-fissured sandstone with a higher dynamic strain rate is characterized by a greater coupled strength under the same static pre-stress; for a given dynamic load, the highest coupled strength occurs under the static pre-stress of 60% UCS. The failure mode of the cross-fissured sandstone is predominantly governed by the dynamic strain rate, independent of static pre-stress variations considered in this investigation. At lower dynamic strain rates, the specimens typically exhibit a mixed tensile-shear failure mode, characterized by the dominance of larger fragments in the broken specimens. In contrast, under high dynamic impacts, the sandstone tends to fail in a shear-dominated manner, resulting in smaller fragments with a more uniform size distribution. Furthermore, the study explores how varying dynamic strain rates and static pre-stress influence the fragment characteristics of the cross-fissured sandstone. Higher dynamic strain rates and increased static pre-stress generally lead to smaller mean fragment sizes. This phenomenon is quantitatively described by fitting fragment size distributions using the Generalized Extreme Value (GEV) distribution, revealing a decrease in the location parameter (μ) and an increase in fractal dimension. These metrics indicate that higher dynamic strain rates and static pre-stress result in sandstone specimens breaking into smaller fragments with a more homogeneous size distribution. These findings contribute to a deeper understanding of rock dynamics, with potential implications for engineering applications involving similar geological configuration under dynamic loading conditions.

Analysis of the dynamic impact behavior and fracture mechanism of coal samples at various temperatures

A thorough understanding of the mechanical properties and fracture mechanisms of coal under high-temperature conditions is crucial for preventing deep coal and rock dynamic disasters. Utilizing the Hopkinson pressure bar experimental system, this study conducts an in-depth analysis of the strength characteristics, failure modes, microscopic properties, and energy consumption effects of coal between 0 and 250℃. The findings reveal that during the heating process, coal’s mass loss increases with temperature, but at a decreasing rate. Significant changes in the coal samples’ dynamic strength, fragmentation, microscopic features, energy evolution, and fracture mechanisms occur at 100℃, marking a turning point in their dynamic behavior. Both dynamic strength and elastic modulus experience a transient increase at 100℃, while the fractal dimension experiences a brief decrease. At 100℃, the thermal expansion of coal particles predominates over the thermal damage from high temperatures, resulting in an increase in the coal samples’ dynamic strength. As the temperature further rises, thermal damage to the coal samples intensifies, leading to a decrease in dynamic strength. Similarly, the absorption and dissipation energy index K of the coal samples experiences a brief increase at 100℃, signifying a sudden change in the energy evolution pattern. Observations of the coal samples’ failure modes upon impact reveal a transition from tensile failure to a combined shear-tensile failure with increasing temperature.