Energy Dissipation Mechanisms Research Articles

Расчеты сжатия сферической слоистой системы ударными волнами с учетом переноса тепла излучением в различных приближениях

Numerical modeling is one of the basic tools to investigate physical phenomena that occur in materials compressed by shock waves. A study of the behavior of shock waves using simplified models is helpful in the analysis of more complex systems, for instance, in the problems of inertial thermonuclear fusion on laser facilities. Mathematical simulation of the nonstationary radiative heat transfer in a spectral kinetic statement is rather complicated because the system of equations is nonlinear and large in size. Generally, the kinetic transport equation is solved in 7D phase space, which requires huge computational resources. The initial system is often approximated under certain assumptions but this immediately causes questions as to whether the simplified model is applicable to particular calculations. In this study, several economic radiative heat transfer models were implemented in a 2D hydrodynamic code. Based on these models, test calculations were performed to simulate the compression of a layered spherical system by shock waves, taking into account radiative heat transfer. When the shock wave reaches the center of the sphere, it is focused and reflected. In the neighborhood of the focal point of a converging wave, temperature gradients increase; therefore, thermal conduction and radiation become the main mechanisms of energy dissipation to be considered when taking into account heat transfer. Maximum densities and temperatures at the center of the sphere and their average values in its regions were calculated. In addition, the time when shock and heat waves cross the sphere center was determined, and their behavior before and after focusing at the sphere center was estimated. It is shown that solutions to such problems can be found much faster and with adequate accuracy when applying simplified models.

New deterministic model for calculating mesh stiffness and damping of rough-surface gears considering elastic–plastic contact and energy-dissipation mechanism

For a long time, meshing parameter calculations and dynamic modeling of gear systems have assumed smooth tooth surfaces, disregarding the impact of actual three-dimensional (3D) microscopic topography. Based on elastic–plastic contact and energy-dissipation mechanisms, this work developed a comprehensive deterministic model that integrates 3D rough surface modeling, reconstruction, and contact analysis, for calculating the time-varying mesh stiffness (TVMS) and mesh damping (TVMD) of deterministic rough-surface gears. Distinct from fractal and statistical models, the deterministic model analyzes deterministic, real 3D rough surfaces rather than simple surfaces defined by a few parameters. Utilizing stochastic process theory, different-topography surfaces are obtained using height and spatial features and reconstructed employing watershed algorithm and ellipsoidal asperity fitting. Subsequently, a deterministic elastic–plastic contact model based on equivalent rough curved-surface contact is constructed, emphasizing local contact states and energy dissipation for calculating contact stiffness (CS) and damping (CD) of gears. Accordingly, a meshing characteristics analysis model is established for calculating TVMS, TVMD, and load sharing ratio (LSR). Experimental validation and comparisons with several statistical and gear contact models demonstrate the effectiveness, reliability, and superiority of the proposed deterministic model. Multi-parameter impact analysis reveals small Sq (meaning low roughness Sa) and Ssk and high load correlate with increased CS and TVMS, while CD and TVMD depend on their interaction and hardness. Overall, by bridging the micro-surface topography and macro-meshing parameters, our model provides essential insights for the design and manufacturing of high-performance gear to reduce vibration and noise.

High-pressure intrusion of double salt aqueous solution in pure silica chabazite: searching for cation selectivity

Heterogeneous lyophobic systems (HLSs), i.e. systems composed of a nanoporous solid and a non-wetting liquid, have attracted much attention as promising candidates for innovative mechanical energy storage and dissipation devices. In this work, a new HLS based on a pure silica chabazite (Si-CHA) and a ternary electrolyte solution (KCl + CaCl2) is studied from porosimetric and crystallographic points of view. The combined approach of this study has been fundamental in unravelling the properties of the system. The porosimetric experiments allowed the determination of the energetic behaviour, while high-pressure in situ crystallographic analyses helped elucidate the mechanism of intrusion. The results are compared with those obtained for systems involving the same zeolite but intruded with solutions containing only single salts (CaCl2 or KCl). The porosimetric results of the three Si-CHA systems intruded by simple and complex electrolyte solutions (KCl 2 M, CaCl2 2 M and the mixture KCl 1 M + CaCl2 1 M) suggest that the intrusion pressure is mainly influenced by the nature of the cations. The CaCl2 2 M solution shows the highest intrusion pressure and KCl 2 M the lowest, whereas the mixture KCl 1 M + CaCl2 1 M is almost in the middle. These differences are probably related to the higher hydration enthalpy and Gibbs energy of Ca2+ compared with those of K+. It has been demonstrated that partial ion desolvation is needed to promote the penetration of the species, and a higher solvation energy requires higher pressure. The `intermediate' value of intrusion pressure shown by the complex electrolyte solution arises from the fact that, statistically, the second/third solvation cation shells can be assumed to be partially shared between K+ and Ca2+. The stronger interaction of Ca2+ with H2O molecules thus also influences the desolvation of K+, increasing the pressure needed to activate the process compared with the pure KCl 2 M solution. This is confirmed by the structural investigation, which shows that at the beginning of intrusion only K+, Cl− and H2O penetrate the pores, whereas the intrusion of Ca2+ requires higher pressure, in agreement with the hydration enthalpies of the two cations.

Experimental study and multi‐scale refinement model of high damping acrylic polymer matrix VEDs for civil structural seismic retrofit

AbstractThe viscoelastic dampers (VEDs), which can provide both stiffness and damping, have been recently introduced into the field of structural vibration control for seismic enhancement of civil engineering structures. In this study, a kind of high damping acrylic polymer matrix VEDs (HDPVED) is developed independently, and this innovative HDPVED can solve the significant problem of service performance under medium‐high temperature environments, as well as low‐frequency vibration control under earthquake actions for civil engineering structures. To systematically investigate the influencing rules of frequency, temperature, and displacement amplitude on the mechanical properties and damping dissipation performance of HDPVEDs, a series of dynamic mechanical performance tests of the developed HDPVEDs are carried out at different frequencies, temperatures, and displacement amplitudes. The research results show that HDPVED exhibits excellent damping dissipation capability and adaptability under medium‐high temperature environments and low‐frequency excitations. The mechanical properties and energy dissipation performance present a strong correlation with frequency, temperature and displacement amplitude, and there is an obvious coupling effect between the three influencing factors. Based on the macroscopic mechanical property research of HDPVED, the microscopic damping mechanism and microscopic mechanical properties of HDPVED are then investigated. High‐order fractional derivative fraction Voigt and Maxwell model in parallel (FVMP) models are preferred to characterize the combined hyper‐elasticity and viscoelasticity owned by networked molecular chains and free molecular chains. The breaking and reconstruction theory of microphysical bonds is used to assess the effect of packing particles, and the time‐temperature equivalence principle is introduced to assess the effect of temperature. The multi‐scale refinement model is proposed, and the validity and accuracy of this model are verified by testing data of HDPVED. The study results show that the proposed model can accurately describe the effects of frequency, temperature, displacement amplitude, and microstructure on the multi‐scale mechanical properties of HDPVED. It provides a theoretical basis for the multi‐scale design and development of high damping VEDs.

Quantification of modeling uncertainty in the Rayleigh damping model

AbstractUnderstanding and accurately characterizing energy dissipation mechanisms in civil structures during earthquakes is an important element of seismic assessment and design. The most commonly used model is attributed to Rayleigh. This paper proposes a systematic approach to quantify the uncertainty associated with Rayleigh's damping model. Bayesian calibration with embedded model error is employed to treat the coefficients of the Rayleigh model as random variables using modal damping ratios. Through a numerical example, we illustrate how this approach works and how the calibrated model can address modeling uncertainty associated with the Rayleigh damping model.

Tailoring Network Topology in Mechanically Robust Hydrogels for 3D Printing and Injection.

Tissue engineering and regenerative medicine are confronted with a persistent challenge: the urgent demand for robust, load-bearing, and biocompatible scaffolds that can effectively endure substantial deformation. Given that inadequate mechanical performance is typically rooted in structural deficiencies─specifically, the absence of energy dissipation mechanisms and network uniformity─a crucial step toward solving this problem is generating synthetic approaches that enable exquisite control over network architecture. This work systematically explores structure-property relationships in poly(ethylene glycol)-based hydrogels constructed utilizing thiol-yne chemistry. We systematically vary polymer concentration, constituent molar mass, and cross-linking protocols to understand the impact of architecture on hydrogel mechanical properties. The network architecture was resolved within the molecular model of Rubinstein-Panyukov to obtain the densities of chemical cross-links and entanglements. We employed both nucleophilic and radical pathways, uncovering notable differences in mechanical response, which highlight a remarkable degree of versatility achievable by tuning readily accessible parameters. Our approach yielded hydrogels with good cell viability and remarkably robust tensile and compression profiles. Finally, the hydrogels are shown to be amenable to advanced processing techniques by demonstrating injection- and extrusion-based 3D printing. Tuning the mechanism and network regularity during the cell-compatible formation of hydrogels is an emerging strategy to control the properties and processability of hydrogel biomaterials by making simple and rational design choices.

A numerical investigation of energy dissipation mechanism of visco-hyperelastic bimaterials subjected to low-velocity impact

Impact protection equipment typically relies on the material failure mechanism and is frequently discarded after the impact. A promising alternative emerges utilizing a foam-infilled lattice bimaterial with shape recovery trait and customizable impact protection capability. This study employs a numerical approach to elucidate the energy dissipation mechanism exhibited by the bimaterial under low-velocity impact condition. The experiment-based inverse method is used to characterize visco-hyperelastic models for two base materials. The investigation reveals that the interaction between the two base materials significantly amplifies the foam’s energy dissipation capability, resulting in an overall higher energy dissipation for the bimaterial. Besides, the study establishes a close correlation between the bimaterial’s effective viscoelastic properties and the enhancement in energy dissipation. Furthermore, the numerical design of experiments (DOE) analysis of base material properties indicates that there is an optimal region for selecting the critical foam material constants for a significant improvement of bimaterial energy dissipation. The results reveal that the combination effect of material interaction and material viscoelastic properties constitutes the fundamental elements of bimaterial energy dissipation mechanism. The insight derived from this study can inform the future design and material selection of a more complicated bimaterial across a wide range of impact protection applications.

Observation of exceptionally strong near-bottom flows over the Atlantis II Seamounts in the northwest Atlantic

Knowledge of near-bottom ocean current velocities and especially their extreme values is necessary to understand geomorphology of the seafloor and composition of benthic biological communities and quantify mechanical energy dissipation by bottom drag. Direct measurements of near-bottom currents in deep ocean remain scarce because of logistical challenges. Here, we report the results of flow velocity and pressure fluctuation measurements at three sites with depths of 2573–4443 m in the area where the Gulf Stream interacts with the New England Seamounts. Repeated episodes of unexpectedly strong near-bottom currents were observed, with the current speed at 4443 m of more than 0.40 m/s. At 2573 m, current speeds exceeded 0.20 m/s approximately 5% of the time throughout the entire eight-week measurement period. The maximum flow speeds of over 1.10 m/s recorded at this site significantly surpass the fastest previously reported directly measured current speeds at comparable or larger depths. A strong correlation is found between the noise intensity in the infrasonic band and the measured current speed. The noise intensity and the characteristic frequency increase with the increasing current speed. Machine-learning tools are employed to infer current speeds from flow-noise measurements at the site not equipped with a current meter.

Study of energy dissipation mechanisms and hotspot formation patterns during impact process in octogen explosives with circular cavities

Considerable focus has been given to hotspot generation and ignition phenomena in impact-induced explosives. Hotspot formation in explosives is typically attributed to internal dissipation and heat transfer occurring within them. This study refines the momentum and energy equations to illustrate the entire process of particle collision, temperature-rise evolution, and hotspot formation in octogen explosive bed under impact. By octogen, we mean the substance known as cyclotetramethylene tetranitramine, which is also commonly referred to as HMX. Dense particles are considered to have pseudo-fluid properties. During the impact of the explosive, we captured the propagation of the stress wave and compared its similarities and differences with the shock wave. The collision force model incorporates a combination of Hertz–Mindlin elastic and Thornton elastoplastic contact theories. The temperature-governing equation includes sliding friction, rolling resistance, and plastic dissipations as energy sources, taking into account the heat transfer processes between particles. Temperature evolution is a spatiotemporally correlated phenomenon divided into three processes: high-temperature bands formation, cavity collapse, and particle bed dispersion, all of which lead to hotspot formation near the cavity and near the wall. Plastic dissipation is the primary source for particle temperature-rise and hotspot formation. Furthermore, the effect of cavity size, impact velocity, and particle size on temperature evolution and hotspot formation patterns is analyzed. It was found that higher impact velocities and smaller cavity sizes are associated with increased hotspot temperatures near the wall, but the hotspot temperature near the cavity does not consistently vary with impact velocity and cavity size. This is attributed to the relationship between energy dissipation rate and void collapse time.

Damping and mechanical behavior of graphene nanoplatelets reinforced Al-30Zn alloy matrix bioinspired laminated composites by two steps flake powder metallurgy

Damping and mechanical properties are often incompatible in metallic materials. In this paper, bio-inspired laminated graphene nanoplatelets (GNPs) reinforced Al-30Zn alloy matrix composites with an outstanding combination of damping-mechanical properties are prepared using a flake powder metallurgy (FPM) process. The increased grain/phase boundary owing to grain refinement improves the intrinsic damping properties of the composites, while the lamellar grains promote the oriented alignment and crack deflection of GNPs. The multilayered GNPs with large specific surface area experienced repeated stretching and compression during cyclic bending deformation, leading to intense interfacial frictional slip, and GNPs' high intrinsic thermal conductivity also helped to dissipate heat quickly, which promoted mechanical energy dissipation. The improvement in mechanical properties is mainly attributed to grain refinement, the load transfer effect of GNPs and their interaction with dislocations. The Al-30Zn-0.5GNPs composites showed the best combination of damping properties and mechanical properties.

A multiple buffering high-fall protection structure and its impact response

High-fall accidents are the most serious safety accidents in the global construction of tall buildings, and existing techniques cannot effectively prevent large-energy impact accidents such as the overall fall of construction formwork, resulting in huge safety risks. Therefore, this paper proposed a flexible protection structure with multiple buffering mechanisms by using a high-strength steel wire net as the intercepting component, and energy dissipators and buffer supports as the buffering and energy dissipation devices. Based on the mechanical model of the critical components, established a simulation model for the overall falling dynamic impact protection of construction formwork, and carried out four cases of parameter analyses that used the material of the intercepting net, whether to use energy dissipators and buffer support as control variables. The analyses show that the multiple buffering and energy dissipation mechanisms composed of steel wire net, energy dissipators, and buffer supports can effectively reduce the response of each component. Nine sets of parametric analyses based on the finalized structure were conducted with the stiffness of the intercepting net and energy dissipator as parameters The results indicate that the smaller the stiffness of the intercepting net and energy dissipator, the better the structural performance. The novel structure proposed in this paper can effectively protect against large-energy falling object impacts and improve the safety of building construction.

Insights into turbulent flow structure and energy dissipation in centrifugal pumps: A study utilizing time-resolved particle image velocimetry and proper orthogonal decomposition

The purpose of the study is to investigate the flow structure and energy dissipation mechanism within centrifugal pump impellers. The velocity fields at the mid-sections of the flow passages of 4- and 5-blade impellers were measured under various flow rates using the Time-resolved Particle Image Velocimetry (TR-PIV) technique; the proper orthogonal decomposition (POD) analysis was performed to extract flow structures with different scales; the dissipation rate was estimated using the large-eddy PIV method; the correlation between turbulent kinetic energy (TKE) and dissipation rate was measured using the cross-correlation analysis. The findings are as follows: impeller with more uniform and stable flow, the scale and energy contribution of large-scale structures in lower order modes are smaller, leading to higher impeller efficiency; large-scale structures identified in the low-order modes correspond to locations of high TKE and dissipation areas; the high velocity gradients within the impeller passage and the interactions between large-scale flow structures encourage the breakup of large-scale turbulent structures into dissipative-scale structures; the correlation between TKE and dissipation rate reflects the extent to which large-scale flow structures within the impeller passage break up into dissipative scales.

Influence of Oxygen/Argon/Nitrogen multi-component plasma modification on interlayer toughening of UHMWPE fiber reinforced composites

The study reveals the influence of glow discharged three gas sources of Oxygen/Argon/Nitrogen plasma modification on interlayer toughening of ultra-high molecular weight polyethylene (UHMWPE) fiber reinforced composite. The failure modes under bending, tensile and interlayer fracture toughness testing were analyzed through acoustic emission (AE) technology. The results showed that Oxygen/Argon/Nitrogen multi-component plasma modified fiber introduced more hydrophilic groups such as hydrogen and hydroxyl groups, and significantly enhanced the binding of fiber and matrix. The GⅠC (Mode-I interlaminar fracture toughness) of multi-component plasma modified composites exhibited increased by 61.67 %, 40.88 % and 18.01 % compared to untreated, Oxygen and Oxygen/Argon plasma, respectively, while GⅡC (Mode-II interlaminar fracture toughness) increased by 38.57 %, 25.57 % and 23.09 %. AE cluster analysis exhibited that multi-component plasma modified composites formed an energy dissipation mechanism dominated by fiber breakage. Additionally, the oxygen, argon, and nitrogen plasma modification have a synergistic effect on interlayer toughening.

Hierarchical-porous acoustic metamaterials: A synergic approach to enhance broadband sound absorption

A novel design for hierarchical-porous acoustic metamaterials (HPAM) is proposed to enhance the functionality of Helmholtz-type resonators and porous materials, achieving continuous and efficient broadband sound absorption. This method can potentially eliminate absorption valley and improve the coupling strength through a synergistic energy dissipation mechanism and hybrid impedance matching behavior. Excellent sound-absorbing capability of the elaborately crafted HPAM was demonstrated analytically, numerically, and experimentally. Specifically, the results revealed an impressive average absorption coefficient of 0.77, with 73 % of the α points exceeding 0.8 across the entire test frequency range. Furthermore, the sound absorption of HPAM can be further optimized to attain ultra-broadband properties by modifying the hierarchical configuration and composite design of the porous materials. The physical mechanism is revealed through the integration of the hierarchical scaling effect and the energy-trapped mode. Numerical simulations revealed the emergence of three distinct absorption peaks at frequencies of 0.76, 1.4, and 3.6 kHz, respectively, and the effective absorption spectrum exceeded 3.4 kHz. Overall, the proposed design highlights the role of hierarchical structures and porous materials in synthesizing superior sound-absorbing properties that fullyelucidate the relationship between structure and performance,and provide an avenue for potential noise-control applications.

Variation characteristics and homology analysis of loaded coal-rock's non-stress signals

When loaded coal-rock is deformed, various non-stress signals, such as temperature-type, electromagnetic-type, and vibration-type, exhibit distinct characteristics as stress'. In order to clarify the relationship between various coal-rock's non-stress signals and establish the corresponding relationship between these characteristics and the damage degree, the study first analysed the generation and evolution mechanisms of the three types of non-stress signals from the perspective of physical mechanisms and energy, and then investigated the changing characteristics of loaded coal-rock's non-stress signals based on uniaxial experiments at different rates. Finally, the homology of non-stress signals is verified by comparing the characteristics of different non-stress signals. The findings indicate that the variation of the non-stress signal is connected to the status of the coal-rock fracture, which is a physical expression of external mechanical energy dissipation. Moreover, the degree of damage inside the coal-rock is proportional to the strength of each non-stress signal source, and the location of the measurement point has no effect on the details associated with coal-rock damage in the non-stress signal. All of the non-stress signals display changing features and fracture precursors connected to the coal-rock damage state. Among the three kinds of non-stress signals, the temperature-type non-stress signal exhibits the most obvious stationarity and stage, whereas the electromagnetic-type and vibration-type signals would fluctuate because of the stress stability. However, they differ greatly in terms of sensitivity to stress variations and difficulties in diagnosing fracture precursors. In addition, the maximum of the vibration-type and electromagnetic-type signals often corresponds with the “plateau” of the temperature-type signal, which means that three different non-stress signal features occur together. Furthermore, the homology of loaded coal-rock's non-stress signals can be efficiently verified by both evidence from theory and experiment. This research can offer a way to determine the loading condition of coal-rock by using non-stress signals, and it can theoretically promote future studies on the prevention of coal and rock dynamic disasters by multi-information fusion.

A friction-strip hybrid damper with multi-phase energy dissipation mechanism: Cyclic test and numerical verification

By combining the frictional and plastic energy dissipation modules (FEDM and PEDM), a novel multi-phase friction-strip hybrid damper (MFSHD) is proposed in the current study. The theoretical analyses demonstrate that, when applied in a self-centering structure, the MFSHD is able to provide higher strength, secondary stiffness and energy dissipation and maintain the self-centering capacity compared with conventional friction dampers. A series of quasi-static tests was conducted on the MFSHD to evaluate the effects of different parameters on the hysteresis performance of the MFSHD. The results showed that increasing the strip number or the bolt pre-tension force could both improve the mechanical performance of the MFSHD. The MFSHD with sandglass-shaped strips had a better performance than that with I-shaped strips. In the MFSHD with lower slipping displacement, the PEDM was activated earlier and provided higher strength, stiffness and energy dissipation, whereas its low-cycle fatigue life was reduced. The numerical analyses based on the model validated by the test results showed that the self-centering braced frame substructure equipped with the MFSHD exhibited hysteresis behavior in consistency with the theoretical model. The superior performance of the MFSHD compared with conventional friction dampers was verified numerically.

Energy dissipation mechanism of annihilating reverse tilt domains for various applied voltages.

When a voltage is applied to a uniformly aligned nematic liquid crystal, a characteristic texture designated as reverse tilt domain (RTD) appears. The RTD, surrounded by a domain wall, gradually shrinks and finally disappears. The domain wall splits into a pair of disclination lines by increase of the voltage. This work examines the energy dissipation mechanism of annihilation dynamics by ascertaining the phenomenological viscosity Γ based on experimentation. To evaluate Γ, the time dependence of curvature radius R is analyzed using an equationR=Asqrt[t_{0}-t], where A is a fitting parameter. Parameter A decreased linearly with increasing applied voltage and suddenly became constant. Also, Γ was evaluated from A as a function of voltage. When the voltage reaches a critical value, Γ increased sharply to be one order of magnitude greater than that under low voltages. The critical voltage is consistent with the theoretically expected value at which the splitting of domain wall occurs. The transition of Γ is described clearly by localized deformation of the director field.

Study on dynamic mechanical properties and microstructure of basalt fiber reinforced coral sand cement composite *

This study investigates the impact of basalt fiber on the static and dynamic compression of coral-sand cement-based composites, as well as the mechanisms for strengthening and toughening. The samples of basalt fiber-reinforced coral sand cementitious composite (BFRCSCC) with varying fiber volume fractions (0%, 0.2%, 0.4%, 0.6%, 0.8%) underwent quasi-static mechanical tests and impact dynamic tests using an MTS universal testing machine and a split Hopkinson pressure bar (SHPB). This study investigates the mechanical properties of BFRCSCC, focusing on static and dynamic compressive strength, dynamic stress-strain curve, strain rate effect, failure strain, toughness analysis, and energy dissipation mechanism. In terms of microstructure, specimens of BFRCSCC were tested using scanning electron microscopy (SEM). The results indicate that basalt fiber can significantly enhance the quasi-static compressive strength (fc)and dynamic compressive strength (fd)of coral sand cement-based composite materials. When the basalt fiber content is 0.4%, the static and dynamic compressive strength of BFRCSCC increases by 28.78% and 37.25% respectively compared to ordinary concrete. The analysis from a micro perspective indicates that the incorporation of basalt fiber in the concrete matrix enhances the hydration reaction between cement and the BFRCSCC interface. The spatial structure formed by basalt fiber contributes to the excellent toughening effect on the mechanical properties of BFRCSCC. As the content of basalt fiber increases (≤0.4%), the bridging effect becomes stronger. The dynamic increase factor (DIF) and toughness index of BFRCSCC exhibit a significant positive correlation with the strain rate effect. Basalt fibers can help drive the hydration products to fill the cracks or voids in the cement matrix, thereby increasing the material's density and enhancing the impact resistance of coral concrete. This can be utilized in practical engineering projects with high dynamic load demands.

Mechanical Behavior and Energy Dissipation of Sandstone–Shotcrete under Monotonic and Cyclic Triaxial Loading

Mechanical Behavior and Energy Dissipation of Sandstone–Shotcrete under Monotonic and Cyclic Triaxial Loading

Enhanced Energy Conversion by Turbulence in Collisionless Magnetic Reconnection

Abstract Magnetic reconnection and turbulence are two of the most significant mechanisms for energy dissipation in collisionless plasma. The role of turbulence in magnetic reconnection poses an outstanding problem in astrophysics and plasma physics. It is still unclear whether turbulence can modify the reconnection process by enhancing the reconnection rate or energy conversion rate. In this study, utilizing unprecedented high-resolution data obtained from the Magnetospheric Multiscale spacecraft, we provide direct evidence that turbulence plays a vital role in promoting energy conversion during reconnection. We reached this conclusion by comparing magnetotail reconnection events with similar inflow Alfvén speed and plasma β but varying amplitudes of turbulence. The disparity in energy conversion was attributed to the strength of turbulence. Stronger turbulence generates more coherent structures with smaller spatial scales, which are pivotal contributors to energy conversion during reconnection. However, we find that turbulence has negligible impact on particle heating, but it does affect the ion bulk kinetic energy in these two events. These findings significantly advance our understanding of the relationship between turbulence and reconnection in astrophysical plasmas.