Mechanical Resistance Properties Research Articles

Equol-based epoxy resin as an ideal substitute for the diglycidyl ether of bisphenol A (DGEBA)

The development of high-performance bio-based epoxies with excellent mechanical properties, heat resistance and flame retardant properties is essential to mitigating the resource and environmental burdens caused by the widespread utilization of petroleum-based epoxies. This work focuses on the synthesis of a bifunctional epoxy resin (EEU) with the rigid tetrahydrobenzopyran ring derived from equol. The structure of the EEU epoxy resin was characterized, and using 4,4′ diamino diphenyl sulfone as the curing agent, the rheological properties, curing behavior and comprehensive properties of cured resin were studied. The results demonstrate that EEU-DDS presents the same curing behavior as DGEBA-DDS. The mechanical properties heat resistance and flame retardant properties of EEU-DDS are superior to DGEBA-DDS. The tensile strength, tensile modulus and glass transition temperature reached to 94.0 MPa, 3.62 GPa and 221 °C, respectively, higher than those of DGEBA-DDS (83.2 MPa, 2.81 GPa and 203 °C). EEU-DDS reached the V-1 rating in UL-94 tests with a high limiting oxygen index (LOI) (28 %), and the peak heat release rate and smoke release rate of 631 kW/m2 and 0.155 m2/s were significantly lower than that of DGEBA-DDS. The flame retardant mechanism was proven to be gas-coacervated phase synergistic flame retardant. In addition, the interlamellar shear strength (ILSS), bending strength, and impact strength of carbon fiber reinforced resin matrix composites prepared by EEU-DDS reached 97.9 MPa, 1281 MPa, and 81.3 kJ/m2, respectively, higher than those of DGEBA-DDS. Therefore, equol-based epoxy resin can serve as an ideal alternative to petroleum-based bisphenol A-type epoxy resin, offering superior comprehensive properties.

Preparation and performance of steel slag and recycled brick aggregate modified concrete under the background of solid waste application

Permeable concrete has the characteristics of breathability, permeability, and high heat dissipation. To improve its mechanical and frost resistance properties, this study optimized the preparation and performance of permeable concrete by adding materials to improve its performance. The performance analysis validate that epoxy resin owns a filling effect on the pores of permeable concrete. The internal curing agent, high water absorbent resin, has a good water absorption effect. The synergistic effect of these two increases the density and compressive strength of permeable concrete. When the two contents are 0.5%, the maximum compressive strength of modified permeable concrete at 7 and 28 days was 15.62 and 17.97 MPa, respectively. Under the action of freeze-thaw cycles, its mass loss rate show an upward trend By comparison, epoxy resin and high water absorbent resin are beneficial for improving the frost resistance of permeable concrete. The minimum value of relative dynamic modulus of elasticity remains stable at over 80%, and the loss rate of dynamic modulus of elasticity is all below 0.4. However, the influence of epoxy resin and SAP on the mass loss rate is relatively small, and the mass loss of all experimental groups is controlled below 2.5%. The binomial Fourier function model is the best predictive model for permeable concrete under freeze-thaw cycles. This study has positive significance for improving the performance of permeable concrete and maintaining the sustainable development of ecological cities.

Experimental investigation in enhancing the mechanical, wear and corrosion resistance properties of Al6061-SiC-NSA composites fabricated using stir casting process

The study investigates the mechanical, and tribological properties of Al6061-SiC-NSA hybrid composites. The characterization via FE-SEM reveals NSA particle’s crystal structure and agglomeration, with an average particle size of approximately 400 nm. The EDS analysis confirms the presence of oxides (TiO2, SiO2, Fe2O3, Al2O3) along with calcium and potassium. The XRD spectra corroborate these findings, additionally identifying Calcite and intermetallic compounds. The Al6061–5SiC-10NSA composites has improved compressive strength of 254 MPa compared to 220 MPa for base Al6061 alloy. The tensile strength of base Al6061 (100 MPa) decreased to 70 MPa for Al6061–5SiC-20NSA composites. The tensile strength decreases with increasing NSA content. Fracture analysis indicates ductile fracture mechanisms, supported by FE-SEM images displaying honeycomb-like structures and dimples. Impact testing reveals reduced impact strength in composites compared to Al6061 (26J3), with Al6061–10SiC-5NSA exhibiting the best toughness of 22.5 J3. Density decreases in composites, with density of Al6061–5SiC-20NSA composites has reduced to 2.40 g cm−3. The microhardness of Al6061–10SiC-5NSA has better value of 109 HV, whereas further addition of NSA has resulted in decrease in microhardness of composites. Pin-on-disc wear tests demonstrate improved wear resistance with increased NSA content, with Al6061–5SiC-20NSA outperforming other compositions. COF decreases with increased NSA content and sliding speed. FE-SEM analysis of worn surfaces reveals that the major wear mechanism is adhesive wear followed by delamination, further the oxide formation along the surface aiding wear resistance of the composites. Tafel testing indicates decreased corrosion potential with increased NSA content, with Al6061–5SiC-20NSA exhibiting improved corrosion resistance.

Investigation of electrostatic interactions in laponite-polyacrylic acid nanocomposites

Nanocomposites provides a unique opportunity to enhance thermal, mechanical, and waterproof resistance properties of polymer. The effectiveness of these enhancements typically depends on the optimal dispersion and interaction of nanofillers within the polymer matrix. The primary objective of this study is to provide direct chemical evidence for electrostatic interactions between Laponite nanofiller and polyacrylic acid. Samples were prepared by mixing Laponite dispersion and aqueous polyacrylic acid (PAA) that were adjusted to various pH conditions. We observed, an IR peak shift in the carbonyl peak of PAA and Si–O peak of Laponite to lower wave number in nanocomposite, with the maximum shift at pH 7. UV–Vis results also showed a hypsochromic shift in the carbonyl peak of PAA due to the interaction with Laponite. The extent of peak shift in IR, and UV–Vis region for the PAA-Laponite dispersion was found to be influenced by the molar mass of PAA used in the formulation of Laponite-PAA nanocomposite and pH of the medium. These results along with zeta potential measurements strongly suggest that electrostatic forces are in play between deprotonated PAA and the positively charged rim of Laponite in promoting electrostatic interactions between Laponite and PAA. The findings of the study can have a strong bearing on the design of next generation high performance coatings, sealants, and adhesives.

Synergistic valorization of rice straw and red brick demolition in development performance of lightweight cement mortars

This work deals with upgrading the undesirable agro- and industrial wastes, such as rice straw (RS), red brick demolition (RBP), and polystyrene foam (PSF), for construction purposes, as an excellent strategy to protect the environment. In this respect, the RS and its pulp fibers are modified by PSF, followed by their incorporating individually or in hybrid with RBP, in cement mortar formulation. As a substitute for fine aggregates. Six rice straw pulps used in this study were prepared from alkali, neutral, acidic, and kraft pulping agents. The effective performance of this investigated route is assessed from the mechanical properties, density, moisture resistance (thickness swelling and water absorption), measurements of the resulting mortar composites, as well as how the investigated treatment effects on behavior of RS fibers. The finding results show that the modified RS fibers, especially those results from KOH–NH4OH and neutral RS-pulping reagents, in hybrid with red brick waste provide motors with better mechanical and water resistance properties. These treated fibers have a synergistic role for including the RBP in mortar formulation to 30 %. The produced mortar has compressive strength 6.2 MPa and flexural strength 4.4 MPa, which is convenient to apply as load-bearing wall. Moreover, they provide improvement in resistance to thickness swelling and water absorption after 24-h exposure to water. The reduction in thickness swelling and water resistance reached 36.7 and 52.8 %, respectively. From the TGA measurements and SEM, it is interesting to notice that the investigated route accepts the RS fibers thermal stability and hydrophobic surface character.

The mechanical and frost resistance properties of pressed concrete blocks mixed with the polymeric aluminum chloride waste residue.

This study aims to research on the mechanical and frost resistance properties of pressed concrete blocks mixed with the polymeric aluminum chloride (PAC) waste residue. Experimental studies on the activity index of volcanic ash, mechanical property, frost resistance and microstructure of pressed concrete blocks mixed with PAC waste residue were carried out. The results show that the activity index of volcanic ash of PAC waste residue reaches 74.96% at a particle size of 0.075mm or less and a curing age of 28days. Based on results of mechanical property tests, the optimum dosage of PAC waste residue is 15%, at which time the compressive and bending strength only decreases by 14.57% and 15.84%. Based on results of frost resistance tests, the optimum dosage of PAC waste residue for pressed concrete blocks is 10%. After 50 freeze-thaw cycles, when the dosage of PAC waste residue is 10%, the strength loss rate is only 3.04%. XRD and SEM tests show that PAC waste residue participates in chemical reactions. With a small amount of PAC waste residue, the structure of the specimen remains dense and therefore the strength decreases less.

Effect of Various Polyimide (PI) Ratios on the Wear Resistance and Mechanical Properties of PI/Polytetrafluoroethylene (PTFE) Blends

Filling polytetrafluoroethylene (PTFE) with polyimide (PI) could effectively improve the properties of PTFE-based blends. In our research described in this article, five PI/PTFE-blend specimens with various conditions were prepared by a cold-pressing, sintering method using various ratios of PI. The PI/PTFE blends were tested for mechanical and wear resistance properties. The surface morphology of the blends was observed using an ultra-field electron microscope. The maximum tensile strength was 32.18 MPa at a PI ratio of 12.5 wt.%. The variation of the PI ratio caused changes in the dispersion of the filler in the matrix, which affected the mechanical properties of the blends. When the PI content was 15 wt.%, the lowest volumetric wear degree of the PI/PTFE blends occurred, 7.8327 × 10−7 mm3/Nm. When the ratio of PI was too high, the PI filler was more likely to be detached from the PTFE matrix in a large area during the friction experiments. This would lead to the blends being more prone to generating abrasive debris during friction, and the buildup and sliding of these abrasive debris on the friction interfaces increased the volumetric wear rate and the coefficient of friction of the blends.

Microstructure and properties of 316 L lattice/Al composites by additive manufacturing and infiltration with different temperature

Interface between lattice reinforcement and matrix played a key factor on properties of the lattice reinforced aluminum matrix composites. However, the effect of interface composed of intermetallic compounds on the properties of 316 L lattice/Al composites was still unclear. In this study, 316 L lattice reinforced aluminum composite with continuous interface were prepared by combining laser powder bed fusion (LPBF) and vacuum infiltration, and effect of infiltration temperature on interface evolution and properties of the composite was investigated. Results indicated that a continuous dual-phase interfacial layer consisting of hard intermetallic compounds η-Fe2Al5 and θ-FeAl3 was formed between the reinforcement and matrix due to diffusion and reaction of iron and aluminum atoms, and the size of needle-type FeAl3 phase in the interfacial zone increased when infiltration temperature was up from 800 °C to 900 °C. It also confirmed that reinforced by 316 L lattice and hard intermetallic compounds layer, the composite showed excellent mechanical and wear resistant properties, with compressive strength of 657 ± 32 MPa and specific wear rate of 0.20 × 10−3 (mm3/N·m) for the sample prepared at 800 °C, which were over 10 times and one fifth of that of the aluminum matrix individually. This study provides a new strategy for developing 316 L lattice/Al composites with excellent properties.

Interface bonding characteristics and thermal damage behavior of brazed diamond with Nb-added Ni[sbnd]Cr filler alloys

NiCr alloy is one of the important filler for brazed diamond tools because of its high hardness, high wear resistance and good wettability to diamond. However, the high brazing temperature and catalytic action of Ni element contained in alloy tend to cause the thermal damage of diamond and interface failure of brazed samples. In this work, the noval NiCr filler alloys added with different contents of Nb are prepared, and the microstructures, mechanical and wear resistance properties of brazed layers used these alloys are investigated. On this basis, the interfacial bonding characteristics and thermal damage behaviors of diamond brazed with Nb-added NiCr filler alloys are further studied. The results show that the addition of Nb element improves the hardness and wear resistance of NiCr filler layer, and the filler alloys exhibit good wettability and climbing effect to diamond. The refined Cr3C2 and Cr7C3 carbides are formed on the surface of diamond, which effectively enhances the interface bonding strength between filler alloy and diamond. Meanwhile, the addition of Nb element consumes some Ni and generates NbNi compound, which weakens, to some extent, the graphitization catalysis and chemical erosion of Ni to diamond. When the addition amounts of Nb are 1–1.2 wt%, the brazed diamond samples present excellent interfacial bonding strength and mechanical properties.

Investigating nano-SiC reinforced WE43 magnesium matrix surface composites

Abstract Magnesium matrix surface composites have been garnering attention due to their superior mechanical and corrosion resistance properties. An idea of facile fabrication of surface composite composed of nano-SiC reinforced WE43 matrix through friction stir processing was explored in this study. Also, the effects of tool geometries, tool rotations, and tool feeds on resultant properties were comprehensively investigated. Uniform dispersion of SiC nanoparticles within stir zone was evident. Square tool demonstrated the most promising results. Processing at 1700 rev min−1 and 60 mm min−1 with a square tool produced finest grains in surface composites exhibited exceptional microhardness (180.8 HV), nanohardness (1.867 GPa), elastic modulus (41.69 GPa), and wear resistance (0.0254 mm3 min−1). Besides it, WE43 substrates also exhibited superior mechanical properties when processed with a square tool at 800 rev min−1 and 60 mm min−1. This research opens up new possibilities for the development of reliable magnesium matrix surface composites for multifunctional applications.

The induced co-deposition of Ni–Mo–W ternary alloy; Coatings for hardness and corrosion resistance applications

Ni–Mo–W ternary alloy coatings were electrodeposited on mild steel substrate using citrate electrolyte for hardness and corrosion resistance applications. The influences electrolyte pH, electrolyte temperature and sodium molybdate concentrations on deposit qualities were studied. The sodium molybdate concentrations were varied from 0.025 to 0.1 M for obtaining alloy coatings with various molybdenum (Mo) compositions. The deposition condition such as electrolyte concentration, pH and temperature were optimized for obtaining good aesthetic (bright) appearance, surface stability and microhardness properties. The maximum Mo composition (47.71 wt %) in alloy deposit was achieved is 47.71 wt % using 0.1 M sodium molybdate concentration. The microhardness properties were increased from 850 HV to 946 HV by introducing molybdenum (47.71 wt %) as third alloying element in to Ni–W alloy matrix. The obtained mechanical and corrosion resistance properties of these ternary alloy coatings were compared with binary alloy and metallic coatings viz., Ni–W and Ni–Mo and metallic Ni coatings. The superior corrosion rate was observed for Ni–Mo–W alloy deposits (5.8 mpy) compared to Ni–W (9.04 mpy) and Ni–Mo (8.89 mpy) alloy.

Carbonation resistance of recycled fine aggregate concrete reinforced by calcium sulfate whiskers

This study investigates mechanical and carbonation resistance tests conducted on Recycled Fine Aggregate Concrete (RFAC) with three different Recycled Fine Aggregate (RFA) replacement rates and four calcium sulfate whisker (CSW) contents, and investigates the effects of RFA replacement rate and CSW content on the mechanical properties of RFAC and the carbonation resistance of RFAC with calcium sulfate whiskers at different ages of carbonation. The microstructure of CSW-modified RFAC was observed and analyzed by SEM electron microscopy to explore further enhancement and toughening mechanisms of CSW in RFAC, as well as the optimal content of CSW in RFAC. In addition, the carbonation depth of recycled concrete with calcium sulfate beard is modeled based on a quadratic fitting formulation. The test results show that the mechanical properties and carbonation resistance of RFAC would decrease with the increase of the RFA replacement rate. Incorporating CSW can effectively improve the mechanical properties and carbonation resistance of RFAC. At 60 % RFA substitution, CSW at 2 % content has the most significant effect on the mechanical properties and carbonation resistance of RFAC. Microscopic analysis shows that CSW has a bridging effect at the micro-cracks in the concrete matrix, preventing the creation and expansion of micro-cracks in the concrete matrix, thus improving RFAC mechanical properties of RFAC and resistance to carbonation. The predicted results of the carbonation depth model which are constructed from the test data coincide with the results. We can use them to predict and analyze the carbonation depth of the carbonation resistance of recycled concrete.

A facile cleaner approach towards the synthesis of silver-doped cardanol-based hydrophobic antimicrobial and anticorrosive polymeric coating material

This work reports the solvent, catalyst and cross-linker free green synthesis of silver (Ag)-doped cardanol-based multifunctional polymer nanocomposite (PNC) coatings. The interaction of Ag ions with the polymeric backbone and in-situ formation of nanoparticles (NP) was confirmed by various characterization techniques. The optimum curing temperature (120–160 °C) and Ag concentration (1%) required for the free-standing film/coating with durable mechanical and chemical resistant properties in acidic/basic/salt solutions was studied. The high gel content (degree of crosslinking, 98%) and thermal stability up to 345 °C endorse the formulation of a well-cross-linked polymeric film/coating. XRD (approx. 27 nm) indicated the formation of crystalline silver nanoparticles within the polymer matrix, whereas SEM and TEM explored the distribution (200–700 nm). EIS studies for three weeks in 3.5% NaCl solution showed the exceptional corrosion inhibition efficiency (98-91%) of the coatings on steel substrate. The stable coating resistance value (MΩ.cm−2) throughout the study highlights the formation of a hydrophobic barrier with good resistance against the corrosive ions. Additionally, the potent antibacterial impact against Gram-positive, and Gram-negative bacteria, and the antifungal activity of the nanocomposite were attributed to the presence of Ag in the PNC. The multifunctional properties arise from the in-situ formed nanostructure and its synergistic effect with the biopolymer matrix projects its versatile industrial application.

Multifunctional Zincophilic Hydrogel Electrolyte with Abundant Hydrogen Bonds for Zinc-Ion Capacitors and Supercapacitors.

The new-generation flexible Zn-ion capacitors (ZICs) require multifunctionality and environmental adaptability for practical applications. This essentially means that hydrogel electrolytes are expected to possess superior mechanical properties, temperature resistance, and tunable interface properties to resist flexibility loss and performance degradation over a wide operating temperatures range. Herein, a multifunctional polyzwitterionic hydrogel electrolyte (PAM/LA/PSBMA) with wide operating temperatures, excellent tensile ability, high water retention, and self-adhesion is designed. Molecular dynamics simulations and experimental results show that polar functional groups (-COO-, -SO3-, -C═O, and -NHCO-) in the hydrogel can form abundant hydrogen bonds with water molecules, which can destroy the original hydrogen bonds (HBs) network between the water molecules and have a low freezing point. It can also form coordination with Zn2+, so that the deposition of Zn2+ electric field homogenization effectively alleviates the growth of Zn dendrites. On this basis, the constructed Zn//Zn cell can be stably cycled 290 h at 10 mA cm-2 (1 mA h cm-2). The constructed ZICs and supercapacitor have a high specific capacitance, excellent energy density, good ionic conductivity, and long cycling stability. This study provides guidance on molecular design for the development of integrated multifunctional smart electronic devices that are environmentally adaptable, resistant to drying, and highly flexible.

Analysis of failure characteristics of screen plates of ring hammer crusher used in coal handling applications

The screen plate, a critical component within a ring hammer crusher (also known as a ring granulator or rolling ring crusher), plays a vital role in the secondary crushing of coal. Functioning both as a platform for coal crushing and as a sieve to achieve the desired coal size, it is essential to understand and examine its failure characteristics to enhance its mechanical and wear resistance properties in coal handling applications. This study thoroughly explored the failure modes, mechanisms, and underlying causes of screen plate failures. Microscopic techniques such as optical microscopy (OM), scanning electron microscopy (SEM), Vickers microhardness test and spectrochemical analysis were utilised to identify the failure mechanism. Failure modes identified from the macroscopic analysis were discharged hole widening, hole wall break-off, plate edge crack, plate fracture, one-sided edge slimming, and general surface wear of the screen plate. The fractographic and wear track analysis identified the principal failure mechanisms of three-body abrasive wear, two-body sliding abrasion wear, shear-induced fatigue fracture and brittle shear fracture. The root causes of the failures are the rotor’s direct impact, defects in the parent material, the presence of hard materials in the coal and the use of unsuitable steel grade in the screen plate manufacturing. The service life of the screen plate can be improved through proper material selection, uniform crusher feeding, surface modification of the surface of the “as purchase” screen plate with appropriate wear-resistant materials, and adherence to good maintenance practices.

Enhancing mechanical properties of surface hardness and abrasion resistance of Fe-Mn-Al alloy by using atmospheric pressure plasma jet nitriding

This study investigates the use of a N2/H2 mixture gas and an atmospheric pressure plasma jet (APPJ) for nitriding Fe-Mn-Al alloy. Pure metals, iron, manganese, and aluminum, were used as the reference metallic substrates. Various characterization techniques, including X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Vickers hardness test, and optical emission spectroscopy (OES), were employed to analyze the material properties and plasma species. XRD analysis revealed the formation of nitride compounds on metals after the nitriding process. The plasma-nitrided Fe-Mn-Al alloy showed the mixture phases of Fe4N and Al, while plasma-nitrided pure metals possessed their specific metal nitrides. After nitriding process, the surface hardness increased to approximately 596 ± 6 HV0.025 for the Fe-Mn-Al alloy, 1307 ± 9 HV0.025 for manganese, 467 ± 4 HV0.025 for aluminum, 646 ± 5 HV0.025 for iron, and, compared to the pristine values of around 346 ± 4 HV0.025, 972 ± 6 HV0.025, 145 ± 3 HV0.025, and 125 ± 3 HV0.025, respectively. After the nitriding process, the Fe-Mn-Al alloy exhibited notable enhancements in both its resistance to abrasion and its capacity to endure impact loads, as indicated by the conducted tests. The OES test results identified NH radicals generated by the atmospheric pressure plasma jet beam as the active chemicals responsible for the success of the nitriding process. Overall, this study provides valuable insights into the strengthening of metal surfaces through nitriding using an N2/H2 mixture gas and APPJ. The results demonstrate significant improvements in surface hardness and surface free energy for iron, manganese, aluminum, and Fe-Mn-Al alloy, highlighting the effectiveness of NH radicals in the nitriding process.

Effect of Combined Laser Thermal and Shock Wave Effects on the Mechanical and Tribological Properties of Steels.

Herein, we present the results of an experimental study on the mechanical properties of Fe-C alloys with different carbon contents (0.2, 0.45, and 0.8%) in a wide range of deformation rates (10-3-103 s-1) and abrasive wear resistance, which underwent combined laser thermal (laser surface hardening-LSH) and laser shock wave (Laser Shock Peening-LSP) processing. The combined treatment modes included a different sequence of exposure to laser thermal and laser-induced shock pulses on the material. The amplitude and duration of laser-induced shock waves were measured using a laser Michelson interferometer. The mechanical properties of steel samples were studied under conditions of uniaxial tension under static loads on a standard universal testing machine, the LR5KPlus, and under dynamic loading, tests were carried out on a specialized experimental complex according to the H. Kolsky method using a split Hopkinson rod. The abrasive wear resistance of hardened surfaces was studied using the Brinell-Haworth method. Studies have shown that the use of a combination of LSH and LSP treatments leads to an increase in both the mechanical properties of steels and abrasive wear resistance compared to traditional laser hardening. It has been established that in the combinations considered, the most effective is laser treatment, in which LSP treatment is applied twice: before and after LSH. Thus, after processing steels using this mode, an increase in the depth of the hardened layer was recorded-by 1.53 times for steel 20, by 1.41 times for steel 45, and by 1.29 times for steel U8-as well as a maximum increase in microhardness values by 22% for steel 20, by 27% for steel 45, and by 13% for U8 steel. The use of this mode made it possible to obtain the maximum strength properties of the studied materials under static and dynamic loading, which is associated with an increase in the volume fraction of the strengthened metal and high microhardness values of the strengthened layer of traditional LSH. The dependences of abrasive wear of the studied steels after various combinations of LSP and LSH impacts were established. It is shown that the greatest wear resistance of the studied steels is observed in the case when the LSH pulse is located between two LSP pulses. In this case, abrasive wear resistance increases by 1.5-2 times compared to traditional LSH.

Development, characterization and application of colorimetric active packaging based on soy protein isolate, trehalose and Oxalis triangularis extract

Colorimetric active packaging based on soy protein isolate (SPI)/trehalose (TRE) and Oxalis triangularis extract (OTE) was developed for monitoring pork spoilage and preserving Actinidia arguta. The formation of intermolecular hydrogen bonds among TRE, OTE, and the SPI matrix resulted in a more compact film structure and improved mechanical, barrier and water resistance properties. The addition of OTE greatly increased the antibacterial and antioxidant activities of the films. The stability of the films improved due to their dense network structure and good barrier and antioxidant capacity. Among all samples, SPI films containing both TRE and OTE (ST-OTE) exhibited the best barrier and mechanical properties after 45 days of storage and maintained a high level of antioxidant activity after heating and UV irradiation. SPI-OTE and ST-OTE films showed good pH sensitivity and responsiveness and exhibited visible color changes during the monitoring of pork spoilage. Compared to the control group, ST-OTE effectively prolonged the storage period of A. arguta.

Study on electrical, thermal, mechanical and corrosion resistance properties of conductive silicone rubber for polymer-based metal composite grounding electrodes

Study on electrical, thermal, mechanical and corrosion resistance properties of conductive silicone rubber for polymer-based metal composite grounding electrodes

Experimental study on compressive properties of mixed fiber concrete after fire

In recent years, the application of high performance self-compacting concrete with high strength, high durability and high workability has become more and more widespread, and has gradually become the main building material. However, high-performance self-compacting concrete increases brittleness while increasing strength, and at the same time, explosion resistance and fire resistance are significantly reduced. With the development of cities, natural gas and intelligent electrical equipment are becoming more and more popular, but people's awareness of fire safety has not been improved, making the incidence of fire in buildings on the rise. In recent years, the development of hybrid fiber self-compacting concrete (HFRSCC), which combines the high workability of self-compacting concrete (SCC) and the high toughness and high crack-resistant properties of fiber concrete (FRC), giving full play to the fiber's anti-cracking, reinforcing and toughening effect, and after the fire and high temperature effect, the components of the use of hybrid fiber self-compacting concrete to maintain a certain degree of residual load-bearing capacity. The introduction of fibers for reinforcement and toughening, to improve the mechanical properties of concrete materials, blast resistance and fire resistance performance points to a direction.