Mechanical Compression Research Articles

Identifying the activated slip modes and twin variants in compressive creep deformation of Mg-8.0Al-1.0Nd-1.0Gd

The compressive creep deformation mechanism of as-cast Mg-8.0Al-1.0Nd-1.0Gd alloy at 180 °C under constant stress of 60 MPa and 90 MPa was novelly analyzed through the distribution characteristics of in-grain misorientation axes (IGMA). Activated slip modes in the creep process was accurately identified and the structure of dislocations is revealed by the weak beam dark-field (WBDF) technology. The intensities of IGMA are concentrated on 011̅0 and 1̅21̅0 axis demonstrates that 0001112̅0(basal slip) and 112̅2112̅3̅ (pyramidal slip) dominate the deformation mechanism. Tensile twins 101̅21̅011 were extensively activated in compression-creep process and the 101̅21̅011 variants with a twinning trace angle close to 90 deg are 1̅012101̅1 and 101̅21̅011 with para-position. The creep mechanism of the alloy crept at 180°C/60 MPa is dominated by grain boundary sliding triggered by the precipitation of β-Mg17Al12, and pipe diffusion-controlled boundary sliding is the dominant creep mechanism of the alloy under 180 °C/90 MPa. In addition, the results reveal that tensile twins induced by dislocation slip contribute to coordinate the grain c-axis deformation, release the stress concentration caused by dislocation accumulation at the grain boundary.

Compressive Mechanical Behavior and Corresponding Failure Mechanism of Polymethacrylimide Foam Induced by Thermo-Mechanical Coupling.

Thermal-mechanical coupling during the molding process can cause compressive yield in the polymer foam core and then affect the molding quality of the sandwich structure. This work investigates the compressive mechanical properties and failure mechanism of polymethacrylimide (PMI) foam in the molding temperature range of 20-120 °C. First, the DMA result indicates that PMI foam has minimal mechanical loss in the 20~120 °C range and can be regarded as an elastoplastic material, and the TGA curve further proves that the PMI foam is thermally stable within 120 °C. Then, the compression results show that compared with 20 °C, the yield stress and elastic modulus of PMI foam decrease by 22.0% and 17.5% at 80 °C and 35.2% and 31.4% at 120 °C, respectively. Meanwhile, the failure mode changes from brittle fracture to plastic yield at about 80 °C. Moreover, a real representative volume element (rRVE) of PMI foam is established by using Micro-CT and Avizo 3D reconstruction methods, and the simulation results indicate that PMI foam mainly shows brittle fractures at 20 °C, while both brittle fractures and plastic yield occur at 80 °C, and most foam cells undergo plastic yield at 120 °C. Finally, the simulation based on a single-cell RVE reveals that the air pressure inside the foam has an obvious influence of about 6.7% on the yield stress of PMI foam at 80 °C (brittle-plastic transition zone).

Contribution of Red Blood Cells and Platelets to Blood Clot Computed Tomography Imaging and Compressive Mechanical Characteristics

Thrombus computed tomography (CT) imaging characteristics may correspond with thrombus mechanical properties and thus predict thrombectomy success. The impact of red blood cell (RBC) content on these properties (imaging and mechanics) has been widely studied. However, the additional effect of platelets has not been considered. The objective of the current study was to examine the individual and combined effects of blood clot RBC and platelet content on resultant CT imaging and mechanical characteristics. Human blood clot analogues were prepared from a combination of preselected RBC volumes and platelet concentrations to decouple their contributions. The resulting clot RBC content (%) and platelet content (%) were determined using Martius Scarlet Blue and CD42b staining, respectively. Non-contrast and contrast-enhanced CT (NCCT and CECT) scans were performed to measure the clot densities. CECT density increase was taken as a proxy for clinical perviousness. Unconfined compressive mechanics were analysed by performing 10 cycles of 80% strain. RBC content is the major determinant of clot NCCT density. However, additional consideration of the platelet content improves the association. CECT density increase is influenced by clot platelet and not RBC content. Platelet content is the dominant component driving clot stiffness, especially at high strains. Both RBC and platelet content contribute to the clot’s viscoelastic and plastic compressive properties. The current in vitro results suggest that CT density is reflective of RBC content and subsequent clot viscoelasticity and plasticity, and that perviousness reflects the clot’s platelet content and subsequent stiffness. However, these indications should be confirmed in a clinical stroke cohort.

Acute Lung Injury after Cardiopulmonary Resuscitation: A Narrative Review.

Although cardiopulmonary resuscitation (CPR) includes lifesaving maneuvers, it might be associated with a wide spectrum of iatrogenic injuries. Among these, acute lung injury (ALI) is frequent and yields significant challenges to post-cardiac arrest recovery. Understanding the relationship between CPR and ALI is determinant for refining resuscitation techniques and improving patient outcomes. This review aims to analyze the existing literature on ALI following CPR, emphasizing prevalence, clinical implications, and contributing factors. The review seeks to elucidate the pathogenesis of ALI in the context of CPR, assess the efficacy of CPR techniques and ventilation strategies, and explore their impact on post-cardiac arrest outcomes. CPR-related injuries, ranging from skeletal fractures to severe internal organ damage, underscore the complexity of managing post-cardiac arrest patients. Chest compression, particularly when prolonged and vigorous, i.e., mechanical compression, appears to be a crucial factor contributing to ALI, with the concept of cardiopulmonary resuscitation-associated lung edema (CRALE) gaining prominence. Ventilation strategies during CPR and post-cardiac arrest syndrome also play pivotal roles in ALI development. The recognition of CPR-related lung injuries, especially CRALE and ALI, highlights the need for research on optimizing CPR techniques and tailoring ventilation strategies during and after resuscitation.

Delayed presentation of Wilkie’s syndrome after scoliotic curve correction surgery: a case report

BackgroundSuperior mesenteric artery (SMA) syndrome, also known as Wilkie’s syndrome, is a rare but serious complication following scoliosis correction surgery. It occurs as a result of mechanical compression of third part of duodenum between the SMA and aorta. This condition occurs most commonly in significantly underweight patients with deformities, and usually during the first week following spinal deformity corrective surgeries. The angle between the abdominal aorta and the SMA gets reduced following spinal lengthening during deformity correction surgery causing compression of third part of duodenum resulting in development of SMA syndrome.Case presentation.We present a case of 17-year-old male with congenital scoliosis with a 70-degree scoliotic curve who underwent spinal deformity correction surgery with posterior instrumented fusion. Post-operative course was uneventful and the patient was discharged after suture removal on post-operative day 15. The patient presented after 21-days of symptom onset on post-operative-day 51, with a 3 week history of post-prandial vomiting, abdominal pain and distension which resulted in rapid weight loss of 11 kg. A CT-angiogram showed obstruction at third part of duodenum. After reviewing clinical and radiological profile of the patient, a diagnosis of SMA syndrome was made. Conservative management was tried, but due to rapid deterioration of patient condition and symptoms of complete intestinal obstruction, the patient was treated surgically by gastro-jejunostomy and side-to-side jejuno-jejunostomy, which improved his condition.ConclusionSMA syndrome can occur much later than previously reported cases and with potentially life-threatening symptoms following scoliosis correction. Having a high index of suspicion, early recognition of condition and institution of appropriate treatment are essential to prevent occurrence of severe complications including risk of intestinal perforation and mortality. This case highlights management of delayed onset of SMA syndrome, with presentation further delayed after symptom onset, as is common in developing parts of the world, due to limited availability and accessibility of resources, and low socio-economic status of large segments of the population.

A single-frame infrared small target detection method based on joint feature guidance

Single-frame infrared small target detection is affected by the low image resolution and small target size, and is prone to the problems of small target feature loss and positional offset during continuous downsampling; at the same time, the sparse features of the small targets do not correlate well with the global-local linkage of the background features. To solve the above problems, this paper proposes an efficient infrared small target detection method. First, this paper incorporates BlurPool in the feature extraction part, which reduces the loss and positional offset of small target features in the process of convolution and pooling. Second, this paper designs an interactive attention deep feature fusion module, which acquires the correlation information between the target and the background from a global perspective, and designs a compression mechanism based on deep a priori knowledge, which reduces the computational difficulty of the self-attention mechanism. Then, this paper designs the context local feature enhancement and fusion module, which uses deep semantic features to dynamically guide shallow local features to realize enhancement and fusion. Finally, this paper proposes an edge feature extraction module for shallow features, which utilizes the complete texture and location information in the shallow features to assist the network to initially locate the target position and edge shape. Numerous experiments show that the method in this paper significantly improves nIoU, F1-Measure and AUC on IRSTD-1k Datasets and NUAA-SIRST Datasets.

Computational Description of a Spinal Compression Mechanism based on Stress-Shielding in an Anteroposteriorly Osteolytic Lumbar Vertebra

Computational Description of a Spinal Compression Mechanism based on Stress-Shielding in an Anteroposteriorly Osteolytic Lumbar Vertebra

Enhanced Energy Absorption with Bioinspired Composite Triply Periodic Minimal Surface Gyroid Lattices Fabricated via Fused Filament Fabrication (FFF)

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop’s Boolean subtraction method, this study combined walled TPMS gyroid structures with a normal TPMS gyroid lattice. This made a composite TPMS gyroid lattice (CTG) with relative densities ranging from 14% to 54%. Using ideaMaker 4.2.3 (3DRaise Pro 2) software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer-aided design (CAD) models and fabricate 36 lattice samples precisely using a layer-by-layer technique. Shimadzu 100 kN testing equipment was utilized for the mechanical compression experiments. The finite element approach validates the results of mechanical compression testing. Further, a composite CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson–Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice’s relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS gyroid lattices in high-speed crash box scenarios to potentially enhance vehicle safety and performance. The structures have tremendous potential to improve vehicle safety by acting as advanced shock absorbers, which are particularly effective at higher relative densities.

Compressive properties and energy absorption of 4D printed auxetic mechanical metamaterials

Auxetic mechanical metamaterials contract or expand laterally when subjected to compressive or tensile load in the axial direction and offer potential benefits in areas such as flexible electronics, aerospace, and soft actuators. Nevertheless, when metamaterials are fabricated using conventional methods, their configurations and properties are fixed, which prohibits adaptation to the specific geometric requirements of their application environment. This limits their further development. This paper proposes an auxetic mechanical metamaterial with a negative Poisson's ratio and energy absorption capability. Compression specimens are fabricated with LCD photo-curable printing technology. The deformation mechanism and in-plane compression characteristics are examined through experimental and numerical simulation methods. The influence of unit cell geometrical control parameters on Poisson's ratio and energy absorption are also explored. The results indicate the dominant deformation mechanism of metamaterial during in-plane compression is bending deformation. The negative Poisson's ratio behavior is more pronounced when compressing along the X direction than along the Y direction, and the specimens also exhibit energy absorption capacity. In addition, the metamaterials prepared by 4D printing technology can be transformed from one configuration to another under external stimuli stimulation and force, and exhibit different mechanical properties, realizing programmable and reconfigurable, further expanding their application range.

Microballoons: Osmotically-inflated elastomer shells for ultrafast release of encapsulants and mechanical energy

HypothesisMicrocapsules with osmotically-inflated elastic shells exhibit an ultrafast release of encapsulants while mechanically stimulating the microenvironments, akin to popping balloons. ExperimentsTo prepare elastic shells with uniform thickness and size, monodisperse water-in-oil-in-water (W/O/W) double-emulsion drops are produced in a capillary microfluidic device. The polydimethylsiloxane (PDMS)-containing oil phase is thermally cured to create the elastic shell. The elastic shells are inflated by pumping water into the lumen in hypotonic conditions. The inflated microcapsules produced undergo mechanical compression, and their release properties are studied. FindingsBy controlling the osmotic pressure difference, Microballoons are inflated into a diameter of 200 μm – 316 μm and shell thickness of 7.8 μm – 0.7 µm, respectively. The inflated shell pops due to mechanical failure when subjected to mechanical stress above a certain threshold, resembling a balloon. During popping, the stretched shell rapidly retracts to the original uninflated state, resulting in an ultrafast release of encapsulants from the lumen within a millisecond. This process converts elastic potential energy stored in the shell into mechanical energy with substantial power. The microballoons mechanically stimulate the local environment, leading to the direct and rapid release of encapsulants. This has the potential to improve absorption efficiency.

Profound hypoxemia and hypotension during posterior spinal fusion in a spinal muscular atrophy child with severe scoliosis: a case report

BackgroundAnesthesia for spinal muscular atrophy (SMA) patients undergoing spinal deformity surgery is challenging. We report an unusual case of an SMA girl who developed severe intraoperative hypoxemia and hypotension during posterior spinal fusion related with surgical positioning.Case presentationA 13-yr-old girl diagnosed with SMA type 2, severe kyphoscoliosis and thoracic deformity was scheduled for elective posterior spinal fusion. She developed severe hypoxemia and profound hypotension intraoperatively in the prone position with surgical table tilted 45° to the right. Though transesophageal echocardiography (TEE) could not be performed due to limited mouth opening, her preoperative computed tomography revealed a severely distorted thoracic cavity with much reduced volume of the right side. A reasonable explanation was when the surgeons performed surgical procedure with the tilted surgical table, the pressure was directly put on the shortest diameter of the significantly deformed thoracic cavity, causing severe compression of the pulmonary artery, resulting in both hypoxemia and hypotension. The patient stabilized when the surgical table was tilted back and successfully went through the surgery in the leveled prone position.ConclusionsSpinal fusion surgery is beneficial for SMA patients in preventing scoliosis progression and improving ventilation. However, severe scoliosis and thoracic deformities put them at risk of both hemodynamic and respiratory instability during surgical positioning. When advanced monitoring like TEE is not practical intraoperatively, preoperative imaging may help with differential diagnosis, and guide the surgical positioning to minimize mechanical compression of the thoracic cavity, thereby helping the patient complete the surgery safely.

Low-cost ternary composite photocatalysts consisting of TiO2, kaolinite and cement for an efficient organic waste decontamination in water

The present study demonstrates the fabrication of heterogeneous ternary composite photocatalyst consisting of TiO2, kaolinite and cement (TKCe), which is essential to overcome the practical barriers that are inherent to currently available photocatalysts. TKCe is prepared via a cost-effective method, which involved the mechanical compression and thermal activation as a major fabrication steps. Clay-cement ratio primarily determines TKCe mechanical strength and photocatalytic efficiency where TKCe with the optimum clay-cement ratio, which is 1:1 results in uniform matrix with fewer surface defects. The composites that have clay-cement ratio below or above the optimum ratio account for comparatively low mechanical strength and photocatalytic activity due to inhomogeneous surface with more defects, including particle agglomeration and cracks. The TKCe mechanical strength is mainly from clay-TiO2 interactions and TiO2-cement interactions. TiO2-cement interactions result in CaTiO3 formation, which significantly increases matrix interactions; however, the maximum composite performance is observed at the optimum titanate level; anything above or below this level deteriorates composite performance. Over 90% degradation rates are characteristic to all TKCe, which follow pseudo first order kinetics in methylene blue decontamination. The highest rate constant is observed with TKCe 1-1, which is 1.57 h−1 and being the highest among all the binary composite photocatalyst that were fabricated previously. The TKCe 1-1 accounts for the highest mechanical strength, which is 6.97 MPa, while the lowest is observed with TKCe 3-1, indicating that clay-cement ratio has direct relation to composite strength. TKCe is a potential photocatalyst, which can be obtained in variable sizes and shapes, complying with real industrial wastewater treatment requirements.

Improving electronics stability via covalent-linked interfaces for ultra-robust pressure sensing array

There is an urgent need for developing ultra-stable sensors with robust interfacial connections to promote the progress of intelligent technology. Here we propose a strategy for fabricating porous sensors with covalent-linked interfaces, which significantly improve the device’s mechanical and environmental stability. By endowing the polymer reactive siloxane group for further dehydration and condensation process, the modified polymer can on one hand form interface covalent Ti-O-Si bonds with hydroxyl-rich MXene nanosheets for improved interfacial adhesion, and on the other hand, form internal self-condensed Si-O-Si bonds for strengthened mechanical resilience. Owing to the firmly undetached conductive materials, the resulting sensor can maintain stable signal output, and survive harsh conditions including repeated mechanical compression and rigorous water and acid washing. These features make the covalent-linked sensor feasible for human sitting posture monitoring over prolonged periods and spatial distribution detection in various complicated operation scenarios.

Mechanical compression regulates tumor spheroid invasion into a 3D collagen matrix

Uncontrolled growth of tumor cells in confined spaces leads to the accumulation of compressive stress within the tumor. Although the effects of tension within 3D extracellular matrices (ECMs) on tumor growth and invasion are well established, the role of compression in tumor mechanics and invasion is largely unexplored. In this study, we modified a Transwell assay such that it provides constant compressive loads to spheroids embedded within a collagen matrix. We used microscopic imaging to follow the single cell dynamics of the cells within the spheroids, as well as invasion into the 3D ECMs. Our experimental results showed that malignant breast tumor (MDA-MB-231) and non-tumorigenic epithelial (MCF10A) spheroids responded differently to a constant compression. Cells within the malignant spheroids became more motile within the spheroids and invaded more into the ECM under compression; whereas cells within non-tumorigenic MCF10A spheroids became less motile within the spheroids and did not display apparent detachment from the spheroids under compression. These findings suggest that compression may play differential roles in healthy and pathogenic epithelial tissues and highlight the importance of tumor mechanics and invasion.

Semi‐Interpenetrated Polymer Networks Based on PHEMA and Modified Chitosan as a Potential Bactericide Hydrogel for Wound‐Healing

AbstractA series of crosslinked hydrogel are developed to evaluate their applicability as efficient carriers for sustained release of ciprofloxacin (CFX) with bactericidal activity. The hydrogels are prepared from 2‐hydroxyethyl methacrylate (HEMA) and carboxymethyl‐chitosan (CMCS) using ethylene glycol dimethacrylate (EGDMA) as crosslinker to yield a semi‐interpenetrating polymer networks (semi‐IPNs) by a photoinitiated chemical method. Molecular weight and concentration of CMCS in the network are varied to optimize its properties as a wound dressing. PHEMA‐CMCS semi‐IPNs (HC‐IPNs) are characterized by their swelling ratio (Q), glass transition temperature (Tg), Young's moduli by mechanical compression submerged in water at different pHs at 37 °C, CFX delivery mimicking skin conditions, cell viability, biodegradability study and by their antibacterial activity. Results show that addition of CMCS results in pH sensitive behavior. HC‐IPNs show thermal reinforcement, and they are softer materials as compared to plain PHEMA hydrogels when submerged in water. The in vitro release of CFX suggests that the HC‐IPNs release the drug continuously up to 50 h. Unloaded HC‐IPNs show inhibition effects against Escherichia coli strain and show bacteriostatic effects against Staphylococcus aureus strain. Results suggest that HC‐IPNs probably be a potential candidate that can be applied as wound dressing for topical CFX controlled delivery.

Oxygenation and ventilation during prolonged experimental cardiopulmonary resuscitation with either continuous or 30:2 compression-to-ventilation ratios together with 10 cmH20 positive end-expiratory pressure

BackgroundIn refractory out-of-hospital cardiac arrest, the patient is commonly transported to hospital with mechanical continuous chest compressions (CCC). Limited data are available on the optimal ventilation strategy. Accordingly, we compared arterial oxygenation and haemodynamics during manual asynchronous continuous ventilation and compressions with a 30:2 compression-to-ventilation ratio together with the use of 10 cmH2O positive end-expiratory pressure (PEEP).MethodsIntubated and anaesthetized landrace pigs with electrically induced ventricular fibrillation were left untreated for 5 min (n = 31, weight ca. 55 kg), after which they were randomized to either the CCC group or the 30:2 group with the the LUCAS® 2 piston device and bag-valve ventilation with 100% oxygen targeting a tidal volume of 8 ml/kg with a PEEP of 10 cmH2O for 35 min. Arterial blood samples were analysed every 5 min, vital signs, near-infrared spectroscopy and electrical impedance tomography (EIT) were measured continuously, and post-mortem CT scans of the lungs were obtained.ResultsThe arterial blood values (median + interquartile range) at the 30-min time point were as follows: PaO2: 180 (86–302) mmHg for the 30:2 group; 70 (49–358) mmHg for the CCC group; PaCO2: 41 (29–53) mmHg for the 30:2 group; 44 (21–67) mmHg for the CCC group; and lactate: 12.8 (10.4–15.5) mmol/l for the 30:2 group; 14.7 (11.8–16.1) mmol/l for the CCC group. The differences were not statistically significant. In linear mixed models, there were no significant differences between the groups. The mean arterial pressures from the femoral artery, end-tidal CO2, distributions of ventilation from EIT and mean aeration of lung tissue in post-mortem CTs were similar between the groups. Eight pneumothoraces occurred in the CCC group and 2 in the 30:2 group, a statistically significant difference (p = 0.04).ConclusionsThe 30:2 and CCC protocols with a PEEP of 10 cmH2O resulted in similar gas exchange and vital sign outcomes in an experimental model of prolonged cardiac arrest with mechanical compressions, but the CCC protocol resulted in more post-mortem pneumothoraces.

Investigation of ballistic and mechanical properties of AlNPB metal matrix composites reinforced with TiCN decorated graphene nano flakes for light armored vehicles

In response to evolving military strategies and technology advancements, this study investigates the ballistic and mechanical properties of novel defense grade Aluminium Nickel Phosphorized Bronze (AlNPB) Metal Matrix Composites (MMCs) reinforced with 2, 4, and 6 wt% of Titanium Carbonitride (TiCN) decorated graphene nanoflakes (TG NPs). The TG NPs were synthesized via modified Hummer's method, mechanically milled with TiCN, and integrated into the AlNPB matrix through the stir casting technique. The fabricated MMCs were characterized using XRD, FTIR, and SEM analyses to evaluate the formation of the nanocomposite and MMC. A series of mechanical tests, including tensile, impact, and compression analyses, identified 4 wt% as the optimum filler loading to enhance mechanical strength. The corrosion resistance of the MMCs was studied alongside their morphological analysis. Explicit ballistic tests yielded satisfactory results, bolstering the potential of the fabricated MMCs for use in Light Armored Vehicles (LAVs). This research contributes a valuable MMC candidate for enhancing the performance and durability of LAVs in challenging environments.

Multiscale characterization of additively manufactured PMMA: the influence of sterilization

PurposePolymethyl methacrylate (PMMA) is a remarkable biocompatible material for bone cement and regeneration. It is also considered 3D printable but requires in-depth process–structure–properties studies. This study aims to elucidate the mechanistic effects of processing parameters and sterilization on PMMA-based implants.Design/methodology/approachThe approach comprised manufacturing samples with different raster angle orientations to capitalize on the influence of the filament alignment with the loading direction. One sample set was sterilized using an autoclave, while another was kept as a reference. The samples underwent a comprehensive characterization regimen of mechanical tension, compression and flexural testing. Thermal and microscale mechanical properties were also analyzed to explore the extent of the appreciated modifications as a function of processing conditions.FindingsThermal and microscale mechanical properties remained almost unaltered, whereas the mesoscale mechanical behavior varied from the as-printed to the after-autoclaving specimens. Although the mechanical behavior reported a pronounced dependence on the printing orientation, sterilization had minimal effects on the properties of 3D printed PMMA structures. Nonetheless, notable changes in appearance were attributed, and heat reversed as a response to thermally driven conformational rearrangements of the molecules.Originality/valueThis research further deepens the viability of 3D printed PMMA for biomedical applications, contributing to the overall comprehension of the polymer and the thermal processes associated with its implementation in biomedical applications, including personalized implants.

Solvent-Free and Cost-Efficient Fabrication of a High-Performance Nanocomposite Sensor for Recording of Electrophysiological Signals.

Carbon nanotube (CNT)-based nanocomposites have found applications in making sensors for various types of physiological sensing. However, the sensors' fabrication process is usually complex, multistep, and requires longtime mixing and hazardous solvents that can be harmful to the environment. Here, we report a flexible dry silver (Ag)/CNT/polydimethylsiloxane (PDMS) nanocomposite-based sensor made by a solvent-free, low-temperature, time-effective, and simple approach for electrophysiological recording. By mechanical compression and thermal treatment of Ag/CNT, a connected conductive network of the fillers was formed, after which the PDMS was added as a polymer matrix. The CNTs make a continuous network for electrons transport, endowing the nanocomposite with high electrical conductivity, mechanical strength, and durability. This process is solvent-free and does not require a high temperature or complex mixing procedure. The sensor shows high flexibility and good conductivity. High-quality electroencephalography (EEG) and electrooculography (EOG) were performed using fabricated dry sensors. Our results show that the Ag/CNT/PDMS sensor has comparable skin-sensor interface impedance with commercial Ag/AgCl-coated dry electrodes, better performance for noninvasive electrophysiological signal recording, and a higher signal-to-noise ratio (SNR) even after 8 months of storage. The SNR of electrophysiological signal recording was measured to be 26.83 dB for our developed sensors versus 25.23 dB for commercial Ag/AgCl-coated dry electrodes. Our process of compress-heating the functional fillers provides a universal approach to fabricate various types of nanocomposites with different nanofillers and desired electrical and mechanical properties.

Analysis of compressive failure mechanism of concrete and grouting cubes by Peridynamics

The structural failure forms and mechanisms of plain concrete, grout, and different aggregate concrete under the action of pressure have been puzzling the engineering and academic circles. To provide more favorable analytical means and theoretical support for structural damage and failure, this paper first adopts the experiments to analysis the compressive failure trend of cubic specimens of concrete and grout, and combines the results with the three-dimensional Peridynamics theory (PD) analyzed the damage trend and failure mechanism of the same tests with the same parameters under load. From the comparison, we can conclude that PD could truly analyze the failure mechanism of three-dimensional structures and was superior to the tests. Meanwhile, we also found that different number and position pebbles have a great influence on the failure path and damage mechanism of concrete.