Measurement Of Oxygen Concentration Research Articles

Hypoxia A Typical Target in Human Lung Cancer Therapy.

Lung cancer (LC) is the leading cause of cancer-related death globally. Comprehensive knowledge of the cellular and molecular etiology of LC is perilous for the development of active treatment approaches. Hypoxia in cancer is linked with malignancy, and its phenotype is implicated in the hypoxic reaction, which is being studied as a prospective cancer treatment target. The hypervascularization of the tumor is the main feature of human LC, and hypoxia is a major stimulator of neo-angiogenesis. It was seen that low oxygen levels in human LC are a critical aspect of this lethal illness. However, as there is a considerable body of literature espousing the presumed functional relevance of hypoxia in LC, the direct measurement of oxygen concentration in Human LC is yet to be determined. This narrative review aims to show the importance and as a future target for novel research studies that can lead to the perception of LC therapy in hypoxic malignancies.

Organosilica Nanosensors for Monitoring Spatiotemporal Changes in Oxygen Levels in Bacterial Cultures.

Oxygen plays a central role in aerobic metabolism, and while many approaches have been developed to measure oxygen concentration in biological environments over time, monitoring spatiotemporal changes in dissolved oxygen levels remains challenging. To address this, we developed a ratiometric core-shell organosilica nanosensor for continuous, real-time optical monitoring of oxygen levels in biological environments. The nanosensors demonstrate good steady state characteristics (KpSV = 0.40 L/mg, R2 = 0.95) and respond reversibly to changes in oxygen concentration in buffered solutions and report similar oxygen level changes in response to bacterial cell growth (Escherichia coli) in comparison to a commercial bulk optode-based sensing film. We further demonstrated that the oxygen nanosensors could be distributed within a growing culture of E. coli and used to record oxygen levels over time and in different locations within a static culture, opening the possibility of spatiotemporal monitoring in complex biological systems.

Validation of a Novel Noninvasive Technology to Estimate Blood Oxygen Saturation Using Green Light: Observational Study

Background Pulse oximeters work within the red-infrared wavelengths. Therefore, these oximeters produce erratic results in dark-skinned subjects and in subjects with cold extremities. Pulse oximetry is routinely performed in patients with fever; however, an elevation in body temperature decreases the affinity of hemoglobin for oxygen, causing a drop in oxygen saturation or oxyhemoglobin concentrations. Objective We aimed to determine whether our new investigational device, the Shani device or SH1 (US Patent 11191460), detects a drop in oxygen saturation or a decrease in oxyhemoglobin concentrations. Methods An observational study (phase 1) was performed in two separate groups to validate measurements of hemoglobin and oxygen concentrations, including 39 participants recruited among current university students and staff aged 20-40 years. All volunteers completed baseline readings using the SH1 device and the commercially available Food and Drug Administration–approved pulse oximeter Masimo. SH1 uses two light-emitting diodes in which the emitted wavelengths match with absorption peaks of oxyhemoglobin (hemoglobin combined with oxygen) and deoxyhemoglobin (hemoglobin without oxygen or reduced hemoglobin). Total hemoglobin was calculated as the sum of oxyhemoglobin and deoxyhemoglobin. Subsequently, 16 subjects completed the “heat jacket study” and the others completed the “blood donation study.” Masimo was consistently used on the finger for comparison. The melanin level was accounted for using the von Luschan skin color scale (VLS) and a specifically designed algorithm. We here focus on the results of the heat jacket study, in which the subject wore a double-layered heated jacket and pair of trousers including a network of polythene tubules along with an inlet and outlet. Warm water was circulated to increase the body temperature by 0.5-0.8 °C above the baseline body temperature. We expected a slight drop in oxyhemoglobin concentrations in the heating phase at the tissue level. Results The mean age of the participants was 24.1 (SD 0.8) years. The skin tone varied from 12 to 36 on the VLS, representing a uniform distribution with one-third of the participants having fair skin, brown skin, and dark skin, respectively. Using a specific algorithm and software, the reflection ratio for oxyhemoglobin was displayed on the screen of the device along with direct hemoglobin values. The SH1 device picked up more minor changes in oxyhemoglobin levels after a change in body temperature compared to the pulse oximeter, with a maximum drop in oxyhemoglobin concentration detected of 6.5% and 2.54%, respectively. Conclusions Our new investigational device SH1 measures oxygen saturation at the tissue level by reflectance spectroscopy using green wavelengths. This device fared well regardless of skin color. This device can thus eliminate racial disparity in these key biomarker assessments. Moreover, since the light is shone on the wrist, SH1 can be readily miniaturized into a wearable device.

Correlation of retinopathy of prematurity with oxygen saturation in preterm babies in a tertiary care center: A noble guide

To find the correlation of retinopathy of prematurity (ROP) with oxygen saturation among preterm babies in neonatal intensive care unit (NICU) of a tertiary care centre. This Prospective cross-sectional study was conducted on 64 premature neonates of gestational age < 36 weeks who were on oxygen and were admitted in NICU after obtaining ethical clearance. We compare the effect of two oxygenation strategies on development of ROP in two groups. Oxygen ranged from 86-90% in one group (32 neonates) and 91-94% in another group (32 neonates). Screening of all neonates were done by one examiner. The data were analyzed using Statistical Package for the Social Sciences (SPSS) version 26. For categorical data, Chi-square test was used. For continuous data, Mann Witney U test were used and p- value-<0.05 was taken as significant. Among 64 babies, 32 babies were on 86-90% of oxygen, 5 babies had disease and the remaining 32 babies who were on 91-94% of oxygen, 14 babies had developed disease showed a statistically significant relationship between ROP and oxygen saturation (p=0.014). High oxygen saturation target is one of the important risk factors leading to the development of ROP. Lower oxygen saturation reduced the prevalence as well as had no deleterious effect on general health of baby. Therefore, accurate measurement of oxygen concentration by probe and proper monitoring of SpO2 levels must be done in every NICU.

Erythrocyte Membrane Camouflaged Nanotheranostics for Optical Molecular Imaging-Escorted Self-Oxygenation Photodynamic Therapy.

Hypoxic tumor microenvironment (TME) hampers the application of oxygen (O2 )-dependent photodynamic therapy (PDT) in solid tumors. To address this problem, a biomimetic nanotheranostics (named MMCC@EM) is developed for optical molecular imaging-escorted self-oxygenation PDT. MMCC@EM is synthesized by encapsulating chlorin e6 (Ce6) and catalase (CAT) in metal-organic framework (MOF) nanoparticles with erythrocyte membrane (EM) camouflage. Based on the biomimetic properties of EM, MMCC@EM efficiently accumulates in tumor tissues. The enriched MMCC@EM achieves TME-activatable drug release, thereby releasing CAT and Ce6, and this process can be monitored through fluorescence (FL) imaging. In addition, endogenous hydrogen peroxide (H2 O2 ) will be decomposed by CAT to produce O2 , which can be reflected by the measurement of intratumoral oxygen concentration using photoacoustic (PA) imaging. Such self-oxygenation nanotheranostics effectively mitigatetumor hypoxia and improve the generation of singlet oxygen (1 O2 ). The 1 O2 disrupts mitochondrial function and triggers caspase-3-mediated cellular apoptosis. Furthermore, MMCC@EM triggers immunogenic cell death (ICD) effect, leading to an increased infiltration of cytotoxic T lymphocytes (CTLs) into tumor tissues. As a result, MMCC@EM exhibits good therapeutic effects in 4T1-tumor bearing mice under the navigation of FL/PA duplex imaging.

Microbiology of Big Soda Lake, a multi-extreme meromictic volcanic crater lake in the Nevada desert.

Big Soda Lake, Nevada, is a multi-extreme meromictic lake, whose hypersaline hyperalkaline bottom waters feature permanent anoxia and high concentrations of arsenic, sulphide and ammonia. These properties make Big Soda Lake-and the adjacent Little Soda Lake-a fascinating system for exploring life's boundaries, discovering novel microbial taxa and identifying biotechnologically useful strains. To date, the taxonomic diversity and metabolic capabilities of microorganisms in this system remain largely unknown. Here, we fill this gap using microbiome surveys across the Big and Little Soda Lake water columns, including 16S rRNA sequencing, fungal ITS2 sequencing and gene- and genome-resolved metagenomics. We accompany these surveys with measurements of salinity, pH, temperature, oxygen, ammonium and ammonia concentrations. Our analyses reveal rich bacterial communities, taxonomically and functionally differentiated along Big Soda Lake's oxycline and, to lesser extent, between lakes. Fungal communities were dominated by a small number of families, while nearly no archaea were detected. Pathways related to perchlorate reduction, anoxygenic phototrophy, fermentation, dissimilatory metabolism of arsenite/arsenate, sulphur compounds, nitrogen compounds and hydrogen, were particularly prevalent. A total of 129 high-quality bacterial and archaeal metagenome-assembled genomes (completeness ≥ 80%, contamination ≤ 5%) were recovered, yielding insight into the taxonomic distribution of microbial metabolic pathways.

Near-infrared spectroscopy for kidney oxygen monitoring in a porcine model of hemorrhagic shock, hemodilution, and REBOA

Acute kidney injury is a common complication of trauma and hemorrhagic shock. In a porcine model of hemorrhagic shock, resuscitative endovascular balloon aortic occlusion (REBOA) and hemodilution, we hypothesized that invasive kidney oxygen concentration measurements would correlate more strongly with noninvasive near infra-red spectroscopy (NIRS) oxygen saturation measurements when cutaneous sensors were placed over the kidney under ultrasound guidance compared to placement over the thigh muscle and subcutaneous tissue. Eight anesthetized swine underwent hemorrhagic shock 4 of which were resuscitated with intravenous fluids prior to the return of shed blood (Hemodilution protocol) and 4 of which underwent REBOA prior to resuscitation and return of shed blood (REBOA protocol). There was a moderate correlation between the NIRS and kidney tissue oxygen measurements (r = 0.61 p < 0.001; r = 0.67 p < 0.001; r = 0.66 p < 0.001for left kidney, right kidney, and thigh NIRS respectively). When the animals were separated by protocol, the Hemodilution group showed a weak or nonsignificant correlation between NIRS and kidney tissue oxygen measurements (r = 0.10 p < 0.001; r = 0.01 p = 0.1007; r = 0.28 p < 0.001 for left kidney, right kidney, and thigh NIRS respectively). This contrasts with the REBOA group, where left and right kidney as well as thigh NIRS were moderately correlated with kidney tissue oxygen (r = 0.71 p < 0.001; r = 0.74 p < 0.001; r = 0.70 p < 0.001; for left kidney, right kidney, and thigh NIRS respectively). There was a strong correlation between both kidney NIRS signals and thigh NIRS measurements (r = 0.85 p < 0.001; r = 0.88 p < 0.001;for left kidney vs thigh and right kidney vs thigh respectively). There was also a strong correlation between left and right kidney NIRS (r = 0.90 p < 0.001). These relationships were maintained regardless of the resuscitation protocol. These results suggest that kidney NIRS measurements were more closely related to thigh NIRS measurements than invasive kidney tissue oxygen concentration.

Residual Complex I activity and amphidirectional Complex II operation support glutamate catabolism through mtSLP in anoxia

Anoxia halts oxidative phosphorylation (OXPHOS) causing an accumulation of reduced compounds in the mitochondrial matrix which impedes dehydrogenases. By simultaneously measuring oxygen concentration, NADH autofluorescence, mitochondrial membrane potential and ubiquinone reduction extent in isolated mitochondria in real-time, we demonstrate that Complex I utilized endogenous quinones to oxidize NADH under acute anoxia. 13C metabolic tracing or untargeted analysis of metabolites extracted during anoxia in the presence or absence of site-specific inhibitors of the electron transfer system showed that NAD+ regenerated by Complex I is reduced by the 2-oxoglutarate dehydrogenase Complex yielding succinyl-CoA supporting mitochondrial substrate-level phosphorylation (mtSLP), releasing succinate. Complex II operated amphidirectionally during the anoxic event, providing quinones to Complex I and reducing fumarate to succinate. Our results highlight the importance of quinone provision to Complex I oxidizing NADH maintaining glutamate catabolism and mtSLP in the absence of OXPHOS.

High-Resolution Respirometry for Mitochondrial Function in Rodent Brain.

High-resolution mitochondrial respirometry is a modern technique that enables to measure mitochondrial respiration in various cell types. It contains chambers with oxygen sensors that measure oxygen concentration via polarography and calculate its consumption. The chamber contains plastic stoppers with injection ports that allow the injection of samples and different substrates, inhibitors, and uncoupler substances to measure mitochondrial respiration with high efficiency. These substances act on the mitochondrial electron transport chain (ETC) and help toassess the mitochondrial ATP production capacity and oxidative phosphorylation. The respirograph obtained with the help of software represents the oxygen consumption in each stage after adding different reagents.

Evaluation and optimization of the performance characteristics of fast response fiber optic oxygen gas probes

Even though many different designs for currently available, fluorescence-based fiber optic sensors for measuring oxygen concentration (O2) are well known (and indeed some are commercially available), they often are limited by their response time and long-term stability. This will cause problems in the important industrial applications of fiber optic sensors of this type that are developing, with limitations that are evident, for example, in physiology and other fields where rapid sensor responses are required. Research by a number of groups has discussed various new designs of fiber optical sensors, which have been developed in recent years where the key features of such probes to achieve the performance required are, for example, optimization of design features such as tip shape and coating layer thickness. The research reported in this paper represents an evaluation of such key factors to allow the design of better fiber optic-based sensors for oxygen measurement, where the optimized performance of a new, specially tapered tip O2 sensor designed has been compared with the output of conventional and commercially available probe designs. The performance of a group of such sensors has been analyzed and cross-compared, examining the key features of such a probe including sensor accuracy, response time and overall long-term stability, as well as cross-sensitivity to any temperature changes which may occur in ‘real’ measurement situations.

Surface oxygen concentration on the Qinghai-Tibet Plateau (2017–2022)

For the ecologically vulnerable Qinghai-Tibet Plateau (QTP), hypoxia is increasingly becoming an extremely important environmental risk factor that significantly affects the health of both humans and livestock in the plateau region, as well as hindering high-quality development. To focus on the problem of hypoxia, it is especially urgent to study the surface oxygen concentration (i.e., oxygen concentration). However, the existing research is not sufficient, and there is a lack of oxygen concentration data collected on the QTP. In this study, through the Second Tibetan Plateau Scientific Expedition and Research and field measurements, the oxygen concentration data and corresponding geographic environmental data were collected at 807 measurement points on the QTP from 2017 to 2022, and the spatiotemporal oxygen concentration patterns were estimated. This work filled the gaps in the measurement and research of oxygen concentrations on the QTP while providing data support for analyses of the influencing factors and spatiotemporal characteristics of oxygen concentrations, which is of great significance for promoting the construction of ecological civilization in the QTP region.

A feasible heat release rate estimation approach for fire hazard assessment in green design

New energy harvesting systems in buildings are becoming more attractive in new green buildings. However, the potential fire hazard of the combustible items used in new green building limits their wider application. Fire behaviour of combustible items in new green designs should be studied carefully. Heat release rate of burning combustible items of different materials is important in fire hazard assessment and can be estimated by oxygen consumption calorimetry. An exhaust hood with a fan-duct system was built to collect flue gas. As the burning was likely to be incomplete in building fires, carbon monoxide, carbon dioxide, water vapor and soot would be emitted. Heat release rates of combustible items were estimated by measuring the transient amount of oxygen, carbon monoxide and carbon dioxide collected by the hood. Based on mass balancing, there are at least three equations in terms of mass flow rates of oxygen, carbon monoxide and carbon dioxide in the incoming air and exhaust gas. There are always questions about using which equations because measuring gases in full-scale burning tests is difficult and expensive. These three equations are introduced and compared in this paper. Heat release rates of four selected combustible items were studied as an example case. Accuracy of the results based on the measured oxygen concentration only was similar to the values provided by commercial software. Results from the experimental data are useful in further full-scale burning tests on combustible items in energy harvest systems planning at the moment.

Evaluation of Usefulness of Yeast-Based Biological Phantom and Preliminary Study for Verification of Hypoxic Effect of Flash Radiotherapy

As a basic hypothesis for the effectiveness of flash radiation therapy, the effect of preserving normal tissue during flash radiation is due to the instantaneous chemical depletion of oxygen. A yeast-based biological phantom was created to verify the hypoxic effect of flash radiation therapy. A study to upgrade the previously developed X-Band LINAC to a flash irradiation mode is in progress, and a preceding study is conducted to evaluate the usefulness of a yeast-based biological phantom manufactured by analyzing the change in oxygen by irradiating a high dose in a general radiation therapy device. Freeze-dried yeast sample (Saccharomyces cerevisiae, S288C) is activated and sub-cultured. For mass production of yeast samples, yeast culture medium is prepared by adding yeast colonies to the ypd medium. This study was conducted to verify the hypoxic effect among the biological mechanisms that occur during flash radiation therapy at the basic stage, and the oxygen concentration change during general radiation irradiation was measured in real time using a DO (Dissolved oxygen) meter and fiber optic sensor designed to do that. To prevent scatter, which is a concern during flash irradiation, the fiber form was used, and precise experiments are possible as a non-invasive oxygen concentration measurement method. Based on 10MV of general radiation therapy device, high-dose radiation of 500-10,000 cGy is irradiated to measure real-time oxygen concentration change. As a result of irradiation with high-dose (500-10,000 cGy) radiation of general LINAC, it was confirmed that the oxygen concentration of the yeast culture medium decreased by 5.7-63.2%, and the usefulness of the biological phantom fabricated based on the yeast culture medium was evaluated. Prior to the analysis of oxygen concentration change in yeast cells during X-Band LINAC flash irradiation, a preliminary study was conducted at a high dose in a general LINAC to obtain a significant result of oxygen concentration change and confirm the usefulness of the yeast-based biological phantom. Prior research was conducted and verified as a general irradiation experiment using a yeast-based biological phantom manufactured based on a DO meter and a fiber optic oxygen sensor. After irradiation with high-dose radiation, the oxygen concentration of the yeast culture medium was measured 5 times, and it was confirmed that there was a change in oxygen concentration of 5.7-63.2%, verifying the usefulness and stability of the biological phantom. The usefulness of the yeast-based biological phantom for high doses was confirmed, and it is expected that the usefulness of the biological phantom for flash radiation can be verified by additionally measuring the change in oxygen concentration of the biological phantom according to the high dose rate in the future.

The metabolic response of human trophoblasts derived from term placentas to metformin

Aims/hypothesisMetformin is increasingly used therapeutically during pregnancy worldwide, particularly in the treatment of gestational diabetes, which affects a substantial proportion of pregnant women globally. However, the impact on placental metabolism remains unclear. In view of the association between metformin use in pregnancy and decreased birthweight, it is essential to understand how metformin modulates the bioenergetic and anabolic functions of the placenta.MethodsA cohort of 55 placentas delivered by elective Caesarean section at term was collected from consenting participants. Trophoblasts were isolated from the placental samples and treated in vitro with clinically relevant doses of metformin (0.01 mmol/l or 0.1 mmol/l) or vehicle. Respiratory function was assayed using high-resolution respirometry to measure oxygen concentration and calculated {dot{V}mathrm{O}}_{2}. Glycolytic rate and glycolytic stress assays were performed using Agilent Seahorse XF assays. Fatty acid uptake and oxidation measurements were conducted using radioisotope-labelled assays. Lipidomic analysis was conducted using LC-MS. Gene expression and protein analysis were performed using RT-PCR and western blotting, respectively.ResultsComplex I-supported oxidative phosphorylation was lower in metformin-treated trophoblasts (0.01 mmol/l metformin, 61.7% of control, p<0.05; 0.1 mmol/l metformin, 43.1% of control, p<0.001). The proton efflux rate arising from glycolysis under physiological conditions was increased following metformin treatment, up to 23±5% above control conditions following treatment with 0.1 mmol/l metformin (p<0.01). There was a significant increase in triglyceride concentrations in trophoblasts treated with 0.1 mmol/l metformin (p<0.05), particularly those of esters of long-chain polyunsaturated fatty acids. Fatty acid oxidation was reduced by ~50% in trophoblasts treated with 0.1 mmol/l metformin compared with controls (p<0.001), with no difference in uptake between treatment groups.Conclusions/interpretationIn primary trophoblasts derived from term placentas metformin treatment caused a reduction in oxidative phosphorylation through partial inactivation of complex I and potentially by other mechanisms. Metformin-treated trophoblasts accumulate lipids, particularly long- and very-long-chain polyunsaturated fatty acids. Our findings raise clinically important questions about the balance of risk of metformin use during pregnancy, particularly in situations where the benefits are not clear-cut and alternative therapies are available.Graphical

Three-dimensional oxygen concentration monitoring in hydrogels using low-cost phosphorescence lifetime imaging for tissue engineering.

Oxygen concentration measurement in 3D hydrogels is vital in 3D cell culture and tissue engineering. However, standard 3D imaging systems capable of measuring oxygen concentration with adequate precision are based on advanced microscopy platforms, which are not accessible in many laboratories due to the system's complexity and the high price. In this work, we present a fast and low-cost phosphorescence lifetime imaging design for measuring the lifetime of oxygen-quenched phosphorescence emission with 0.25 µs temporal precision and sub-millimeter spatial resolution in 3D. By combining light-sheet illumination and the frequency-domain lifetime measurement using a commercial rolling-shutter CMOS camera in the structure of a conventional optical microscope, this design is highly customizable to accommodate application-specific research needs while also being low-cost as compared to advanced instruments. As a demonstration, we made a fluidic device with a gas-permeable film to create an artificial oxygen gradient in the hydrogel sample. Dye-embedded beads were distributed in the hydrogel to conduct continuous emission lifetime monitoring when nitrogen was pumped through the fluidic channel and changed oxygen distribution in the sample. The dynamics of the changes in lifetime co-related with their location in the gel of size 0.5 mm×1.5 mm×700 µm demonstrate the ability of this design to measure the oxygen concentration stably and precisely in 3D samples.

Development of Monitoring Parameters of Oxygen Concentration, Oxygen Flow Rate, Temperature and Humidity in IoT-Based CPAP Bubble (Oxygen and Humidity Concentration)

Bubble Continuous Positive Airway Pressure (CPAP) is a device to maintain positive pressure in the neonate's airway as long as it can breathe spontaneously. FiO2 percentage, flowmeter, humidifier mode, PEEP depth are parameters that must be set for oxygen therapy using a cpap bubble device, but this tool has minimal monitoring. It has been developed by several previous researchers but has several shortcomings, namely there is no digital result display, no measurement of oxygen rate, oxygen concentration, temperature and humidity. The purpose of this research is to design a parameter monitoring tool on the cpap bubble so that it can monitor the baby's condition in real time and can be used as an indicator of achieving the desired concentration setting. The contribution in this study is a monitoring system or remote monitoring so that nurses and doctors can monitor the baby's condition even though they are not accompanying him. In order to facilitate the process of monitoring and diagnosing patients, a parameter monitoring tool on the cpap bubble based on the Internet of Things is made with notifications on telegrams so that patients can be treated quickly. The design of this tool uses OCS-3f as a sensor for detecting oxygen concentration and DHT22 as a sensor for detecting humidity. The output of oxygen and humidity concentrations is then processed by the ESP32 microcontroller into the ADC pin. Data that has been processed from analog sensor data into digital data on the ESP32 is then sent to the https://thinger.io site using the internet network via the wifi module contained in the ESP32 module build-in. In measuring positioned in the settings of 21% to 95%. The largest error value obtained is 4.6% and the smallest is 0.04%.

Artificial Circulation Effect on Oxygen Saturation in the Brain Phantom

Cardiovascular surgery represents a field where the anesthetist frequently deals with quickly evolving conditions associated with anesthesia, perfusion, and the scope of surgery, that have a direct and indirect impact on the oxygen delivery to organs and tissues and its consumption ratio. The prospects of predicting the oxygen concentration influential factors on the brain create a possibility for effective decisions in the crucial moments of cardiac surgery during a cardiopulmonary bypass, to choose specific neuroprotection to decrease postoperative neurologic complication risk. Nowadays, near-infrared spectroscopy (NIRS) technology has been used to perform cerebral oximetry analysis. By reviewing available literature, the work on the possible dependence of artificial blood circulation on oxygen concentration in the brain is provided. This research aims to investigate how artificial circulation, specifically the flow and viscosity of the fluid equivalent to blood, affects oxygen concentration in the cerebral phantom. The thesis contains methodology for measuring the concentration of oxygen was considered, as well as the manufacture of a phantom of the brain and an equivalent blood fluid. The results illustrate that the artificial blood flow rate has a non-linear effect on the oxygen concentration in the brain phantom. This was confirmed through the value of the oxygen concentration in the brain phantom under conditions of artificial blood circulation rSO_2avg.= 85% with laminar flow and the value of rSO_2avg.= 78% with turbulent flow. Additionally, it was proven that as the viscosity of the blood-equivalent fluid increases, the oxygen concentration decreases almost linearly. The calculated average rSO₂ value at minimum viscosity η=2.0 mPa∙s and flow rate Q=0.5 l/min has maximum rSO_2avg.=85%, while at maximum viscosity η=4.2 mPa∙s, rSO₂ average value was the smallest rSO_2avg.=72%. The study demonstrates that the type and rate of flow, as well as viscosity of the cardiopulmonary bypass, affect the measurements of oxygen concentration in the brain phantom.

Design and realization of a mobile-automatic calibration system for ventilator testers: oxygen concentration

Ventilators have a vital role in supplying oxygen to the patients experiencing respiratory failure and ensuring the patient’s oxygen saturation to levels above 50% continuously. Therefore, the accuracy of oxygen concentration measurement becomes very important to assure patient safety obtained by testing the ventilator against a ventilator tester. Testing and calibration laboratory use a ventilator tester for routine calibration of health facilities as well as performance and clinical testing for emergency ventilators that developed massively these days. A mobile-ventilator tester calibration system for oxygen levels, especially for concentrations of 30%, 60%, and 90% according to SNI ISO 80601-2-12:2020, is being developed. This calibration system is designed to operate automatically based on Laboratory virtual instruments engineering workbench (LabVIEW) to control the instrumentation system and perform data acquisition of (oxygen concentration) readings. Three concentrations of oxygen gas reference are stored each on 2 L gas reservoirs to ease the mobilization of the system to testing and calibration laboratory. Hopefully, the traceability to International System of Units (SI) for the ventilator tester can be realized with this calibration system, thus can improve the quality of health services and increase the competitiveness of nationally produced medical devices. Although some improvements are required, the prototype of the calibrator works appropriately as intended.

Development and measurement of airborne oxygen sensor for aircraft inerting system based on TDLAS with pressure compensation and 2f/1f normalized method

Using Tunable Diode Laser Absorption Spectroscopy (TDLAS）technology to accurately measure the oxygen concentration in the ullage of the aircraft fuel tank is of great significance to ensure the safety of the aircraft and improve the working quality of the aircraft onboard inerting system. This paper focuses on designing a smart sensor for the detection of oxygen concentration applied to airborne inerting systems, which can reduce random environmental noise and lineshape errors during the flying process. First, a prototypeincluding a laser emission module with wavelength modulation and temperature control, a multi-reflection long optical path absorption gas cell, and a high-precision signal extraction module are designed. Then, ground experiments at 294 K, and 1 bar are carried out. The oxygen inversion method is designed, the oxygen concentration results are obtained, and the lower detection limit (3.3 ppm) and detection accuracy (9.6 ppm) of the sensor are discussed. Thirdly, the change of absorption line profile influenced by the change of pressure is discussed. The series of oxygen concentration measurement experiments with variable pressure (274 k, 1–0.1 bar) was carried out. and the measurement error is below 1%. Finally, a second harmonic (2f)/first harmonic (1f) normalized method is proposed to eliminate the errors caused by laser attenuation and environmental vibration in oxygen measurement.

Abstract 190: Personalized identification of cancer treatments in real-time: TumOC - a tumor organoid-on-chip platform for online cell vitality measurements

Abstract Enhanced, physiologically relevant in-vitro tumor models significantly increase the success rate in new drug development, reduce the number of animal experiments and result finally in better therapies for cancer patients. Furthermore, they have the potential to offer new approaches to personalized oncology. In recent years, 3D cell cultures were established as relevant preclinical cancer models, suitable for high-throughput-screening. However, their capacity to model and/or measure physiological processes can still be enhanced. Colorectal carcinomas (CRC) are one of the most common malignant tumors. Due to its heterogeneity and high probability to metastasize, the disease is often incurable and novel, improved therapies are urgently needed. In this project, we developed a tumor organoid-on-chip platform (TumOC) by combining most recent technological advances: We integrated CRC patient-derived 3D cell cultures (organoids) and microsensor particles that enable assessment of cell vitality in real time by measuring oxygen concentration in a microfluidic system. The resulting TumOC platform allows for defined exposition of cytostatic drugs including dynamic and combination treatments. Measurements of cell vitality in real time enables analysis of not only the final effect of a drug treatment, but also the kinetics of drug response. At the same time, utilizing organoids allows for recapitulating tumor architecture and heterogeneity. Using the TumOC platform, we measured the cell vitality in real time over several days during treatment with classic chemotherapeutics or targeted cancer drugs and compared the results to end-point measurements on the same organoids in a static system. We assessed the effect of intra- and intertumoral heterogeneity and developed a protocol for treatment with clinically used combination regimes. In conclusion, our TumOC platform with its ability to recapitulate tumor heterogeneity in combination with dynamic treatments and real-time cell vitality assessment is an in-vitro tumor model closely recapitulating the physiological situation in a patient. TumOC provides an impressive opportunity to test and, consequently, predict the effectiveness of anti-cancer therapies. Therefore, this system is of interest not only for pre-clinical drug development but also for personalized oncology. Citation Format: Marie Flechner, Juergen Loskutov, Madeleine Nadolny, Ulrike Pfohl, Christian R. Regenbrecht, Katja Uhlig, Lena Wedeken. Personalized identification of cancer treatments in real-time: TumOC - a tumor organoid-on-chip platform for online cell vitality measurements [abstract]. In: Proceedings of the American Association for Cancer Research Annual Meeting 2023; Part 1 (Regular and Invited Abstracts); 2023 Apr 14-19; Orlando, FL. Philadelphia (PA): AACR; Cancer Res 2023;83(7_Suppl):Abstract nr 190.