Measurement Of Dielectric Properties Research Articles

Study on the high resistivity and resonant frequency characteristics of Eu-doped NiZnCo ferrites

To fulfill the urgent demand for materials suitable for contemporary high-frequency applications, Eu-substituted Ni0.55Zn0.35Co0.1EuxFe2-xO4 (NZCEF, 0 ≤ x ≤ 0.10) composite ferrites were successfully synthesized by a solid-state reaction method, demonstrating characteristics apt for high-frequency functionalities. Detailed examination via SEM and EDS confirmed the compositional purity of these ferrites. Microstructural analysis indicates that the incorporation of europium results in a reduction of the average grain size in NZCEF composites, enhancing the material's densification. Measurements of resistivity and dielectric properties reveal that Eu doping affects the concentration of Fe2+ and Fe3+ ions as well as lattice defects within the ferrite, thereby leading to higher dielectric constants and resistivity (ρ, 6.51 × 108 Ω m). Magnetic analysis confirms that the substitution with Eu ions significantly increases both the coercivity and the ferromagnetic resonance frequency (fr), from 25.7 Oe and 445 MHz to 45.73 Oe and 1.22 GHz, respectively. This improvement is attributed to changes in grain size and domain wall motion. Consequently, Eu3+-substituted NZCEF ferrites exhibit superior electromagnetic properties, making them ideal candidates for advanced high-frequency material applications.

CaCu3Ti4O12 ceramic via oxalate route: Synthesis, characterization and electrical properties

In this manuscript, a new method for the synthesis of CaCu3Ti4O12 (CCTO) perovskite was adopted via co-precipitation followed by calcination processes. The co-precipitation route was employed to synthesize calcium and copper oxalates precipitated on the TiO2 surfaces and the calcination technique at different temperatures was utilized to follow the single-phase formation. Differential thermal analysis-thermogravimetry (DTA-TG) were used to estimate the proper calcination temperatures and to follow the precursor′s decomposition stages. X-ray diffraction (XRD) revealed the initiation of titanate formation at 700 °C. The complete formation of single-phase was achieved at 1100 °C. In agreement with the XRD measurements, FT-IR spectra confirmed the formation the different phases at different calcination temperatures. The prepared titanate showed giant dielectric properties with values higher than reported in literature. The conductivity measurement indicated semi-conducting properties and revealed a transition agreed well with that obtained in the dielectric properties measurements vs. temperature, attributed to the orientional polarization or change in the entire conduction mechanism from hopping to ionic conduction. The obtained electrical properties enhances the utilization of the entire titanate as capacitors.

Non-contact near-field cavity perturbation method for quantitative dielectric measurement and metallic defect inspection

Low dielectric constant (low-k) materials are essential in electronic industry aiming at new generation high-speed communications. Dielectric constant of these materials are measured by standard procedures and instruments with conventional contact configuration. Non-contact and in-situ techniques for low-k dielectric measurement are highly demanded in practice and worth of investigation. We hereby proposed a near-field microwave probe (NFMP) to accurately measure dielectric constant of low-k samples in a non-contact manner with a quantitative electromagnetic (EM) cavity perturbation theory. An NFMP set was designed, optimized by finite-element method (FEM) and fabricated with handy materials in the lab. Frequency response of the NFMP was tested experimentally and further used for subsequent frequency displacement analysis. Various low-k samples were tested by the non-contact NFMP set and dielectric constant were extracted based on the field perturbation theory. The relative error was obtained less than 0.5 % for low-k materials. The NFMP was then fixed on a micrometer stage and worked in a line-scan mode to inspect conductive defects in a low-k substrate. Both surface and subsurface defects were inspected by analyzing displaced central frequencies. The NFMP system is promising to facilitate quantitative and non-contact dielectric property measurement in electronics.

Solid materials microwave dielectric properties: features of methods practical use

Features of methods practical use for material dielectric properties measurement in different (factory and metrological) laboratories and influence of above mentioned features on measurements results are considered. Results are obtained by Obninsk Research and Production Enterprise “Technologiya” A. G. Romashin radiophysics laboratory and by East-Siberian branch Federal State Unitary Enterprise “Russian metrological institute of technical physics and radio engineering” department of radio engineering measurements. Results of microwave permittivity and loss tangent solid materials measurements are analysed. This investigation made it possible to get additional information about features of standard methods practical use for material dielectric properties measurement, which was absent in literature earlier. In laboratories for measurements used the waveguide resonator and the standardized techniques. The factory laboratory applied a measurement method at the fixed frequency with control in a resonance movement of the plunger, and in metrological laboratory a measurement method with the fixed length of the resonator and measurement at resonant frequencies. Results of measurements showed good reproducibility of results for samples that are meeting method requirements. It was revealed reducing reproducibility of measurements of hygroscopic, heterogeneous samples and in the case of nonobservance of diameter method requirements. Obtained results can be applied for reproducibility improvement of dielectric properties measurements in practical use of considered methods.

Structural Elucidation and Evaluation of Magnetic and Dielectric Properties of Lu–La Co‐substituted M‐Type Hexagonal Ferrites Synthesized by Chemical Co‐precipitation Method

In this research, LuxLaySr1–yFe12–xO19, an M‐type strontium ferrite, is synthesized using the coprecipitation method with precursor chemicals. The samples undergo analysis for structure, morphology, and elemental composition through X‐ray diffraction (XRD) and scanning electron microscopy (SEM). Magnetic and dielectric properties are determined using a vibrating sample magnetometer (VSM) and a dielectric property measurement instrument (LCR), respectively. The primary objective of this study is to enhance the dielectric performance of the samples through rare‐earth element doping. The XRD analysis reveals that the samples display a hexagonal single‐phase magnetoplumbite crystal structure. SEM micrographs illustrate a regular hexagonal structure of the grains. VSM analysis affirms LuxLaySr1–yFe12–xO19 as a hard magnetic material with a high coercivity. As the rare‐earth element content increases, the coercivity of the samples significantly decrease from 2065.3 to 910.3 Oe. Dielectric property analysis demonstrates that augmenting the rare‐earth element (Lu–La) content notably increases the relative dielectric constant of the samples. In the low‐frequency region, the relative dielectric constant ranges from 6.71 × 103 to 1.28 × 105, while in the high‐frequency region, it ranges from 3.09 × 103 to 2.03 × 104. Samples doped with rare‐earth elements exhibit a high dielectric constant and low coercivity, rendering them suitable for applications in electromagnetic shielding materials. This can help reduce interference from magnetic fields on internal components while blocking electromagnetic waves.

Field dependence of the electrocaloric effect in BaTiO3 and Ba(Zr0.12Ti0.88)O3: High-resolution measurements around the phase transition

The electric field dependence of the electrocaloric effect is investigated in BaTiO3 and Ba(Zr0.12Ti0.88)O3 by a direct method with sub-mK temperature resolution. The field dependence of the caloric temperature change ΔT(E) shows a pronounced change within a few Kelvin around the Curie temperature for the first-order phase transition in BaTiO3. The transition from a linear field dependence in the ferroelectric phase over a butterfly-shaped to a quadratic field dependence in the paraelectric phase is compared to predictions of Landau–Devonshire theory. The simultaneous measurement of caloric and dielectric properties further allows for the investigation of the polarization dependence ΔT(P) of the electrocaloric effect. We find clear deviations from the predicted quadratic polarization dependence for temperatures close to the Curie temperature. Ba(Zr0.12Ti0.88)O3 shows in contrast only a slow and gradual change of the field dependence over a broad temperature range as a consequence of its diffuse phase transition.

Compaction pressure effect on the dielectric, DC and AC conductivity of C-130 porcelain

Porcelain insulators can be prepared in a variety of compositions using several different preparation techniques. In the frame of the present work the effect of the applied compaction pressures on the C-130 grade electroporcelain was studied in terms of electrical and dielectric properties. Compaction is a widely used preparation process, nevertheless, a little is known about the effect of the compaction pressure on the final electrical properties of the material. Samples prepared with different compaction pressures (from 70 MPa to 110 MPa; 10 MPa step size) were subjected to a measurement of DC conductivity up to 1200 °C, and a measurement of dielectric properties at room temperature after different firing temperatures. The DC conductivity of the raw samples ranged from ∼10−10 S/m at room temperature to <10−3 S/m at 1100 °C. Temperature dependence of the DC conductivity revealed that the dominant charge carriers were H+ and OH− ions (initial stages of heating) and alkali ions (at high temperatures and during second heating). The DC conductivity of the previously fired samples (at 1100 °C) ranged from ∼10−12 S/m (room temperature) to ∼10−3 S/m (1200 °C). The AC conductivity of the samples ranged from ∼10−7 S/m (samples fired at 1300 °C, measured at low frequencies) to ∼10−3 (raw sample, measured at high frequencies). AC conductivity measurements and dielectric analysis confirmed that the conduction occurred through ion hopping and the bulk boundary conductivity was dominant. The relative permittivity reached 7–8 after firing at 1300 °C at frequencies above 2 MHz.

3D Imaging and Quantitative Subsurface Dielectric Constant Measurement Using Peak Force Kelvin Probe Force Microscopy

AbstractNoninvasive and depth‐sensitive measurements of dielectric properties are becoming of great interest in advanced and complex nanostructured architectures. Here, a straightforward parallel approach applicable in peak force Kelvin probe force microscopy for a 3D measurement of dielectric constants at the nanoscale is demonstrated. The proposed approach features a simultaneous measurement of the mechanical, electrical, and depth‐dependent dielectric properties applied to embedded nanostructures. The findings provide initial elements for further development of experimental dielectric nano‐tomography methods for characterizing buried and embedded systems and dielectric interfaces.

Study on the difference of high frequency dielectric properties of biological tissues measured by air and packed coaxial probe

In this paper, the differences between air probe and filled probe for measuring high-frequency dielectric properties of biological tissues are investigated based on the equivalent circuit model to provide a reference for the methodology of high-frequency measurement of biological tissue dielectric properties. Two types of probes were used to measure different concentrations of NaCl solution in the frequency band of 100 MHz-2 GHz. The results showed that the accuracy and reliability of the calculated results of the air probe were lower than that of the filled probe, especially the dielectric coefficient of the measured material, and the higher the concentration of NaCl solution, the higher the error. By laminating the probe terminal, liquid intrusion could be prevented, to a certain extent, to improve the accuracy of measurement. However, as the frequency decreased, the influence of the film on the measurement increased and the measurement accuracy decreased. The results of the study show that the air probe, despite its simple dimensional design and easy calibration, differs from the conventional equivalent circuit model in actual measurements, and the model needs to be re-corrected for actual use. The filled probe matches the equivalent circuit model better, and therefore has better measurement accuracy and reliability.

Dielectric and optical properties, high temperature conduction, and relaxation behavior of donor-element modified NBST material

The relaxor ferroelectrics (Na0.33Bi0.33Sr0.33) (Ti1-xW0.666x)O3, where 0%≤ x ≤7% (NBST+0W, NBST+3W, NBST+5W, and NBST+7W), were prepared using the solid-state reaction method. X-ray diffraction analysis showed that perovskite structures were formed at room temperature. Microstructural characterization, as well as optical and dielectric property measurements, yielded the following results: substituting Ti4+ with the donor element W6+ led to a decrease in the average grain size, dielectric loss, degree of diffusivity, and affected the temperature Tm. In the case of x = 3% of WO3, the electrical conductivity of NBST improved at high temperatures. However, the compound (NBST+7W) exhibited a low optical gap energy and high electrical conductivity at room temperature. The electrical conductivity curves were fitted by Jonscher power law, which showed that the correlated barrier hopping (CBH) model was the most dominant. Comparison of the imaginary part of impedance and electric modulus revealed that the relaxation of charge carriers in the basic compound NBST+0W occurred at both long and short ranges. However, after doping, the relaxation occurred only at a short range.

Characterization of Nano-Structured Magnesium-Aluminum Ferrites Synthesized by Citrate-Gel Auto Combustion Method

An effort is made to find the solution to the new challenges of modification advancements in ferrite technologies. The hypothetical variation in the structural, magnetic, and electrical properties of cubic spinel magnesium aluminum ferrites introduced by the substitution of doping elements has been rationalized and proven. The outcome of aluminum substitution on the magnesium ferrites has been examined and investigated. Spinel ferrites having compositions of MgAlxFe2-xO4 (x = 0.1, 0.2, 0.3, 0.4) were prepared by the sol-gel auto-combustion method. The prepared sample’s characterization, such as scanning electron microscopy (SEM), DC electrical resistivity, AC electrical resistivity, and dielectric properties measurements, were tested using the respective instruments. The grain size and crystal size of all samples were measured from the micrographs of SEM and XRD Data. It is found that the average grain size is within the range of 300 nm - 550 nm for all different series that are formed, keeping the samples at 1100 °C sintering temperatures. A two-probe method experiment with a temperature range of 30 °C to 500 °C gives data on DC electrical resistivity. The Curie temperature depends on the sintering temperature, and it increases with increasing doping concentration. Also, doping influences grain size, which decreases with increasing concentration. Analyzing the SEM micrographs, it is found that the average grain size must decrease in tendency with increasing Al content. DC electrical resistivity exhibits excellent semiconducting behavior. Frequency dependence, dielectric constant, and dielectric loss factors were measured, keeping the frequency range of 75 Hz to 130 MHz at room temperature. The result shows that the dielectric constant (e) and dielectric loss tangent (tan™) decrease with the increase in frequency, while the AC resistivity and Q-factor increase. Comparing the electrical properties of four compositions, it can be suggested that the mixed ferrite, sample-4 (x = 0.3), shows the highest Q-factor of all at 1100 °C.

Fabrication of cellulose-based polymer electrolyte membrane with green solvent DMSO via N-TIPS technique

Solid polymer electrolyte membrane for Li-ion battery was fabricated via N-TIPS technique. To substitute commercially available polyolefin-based separator with more sustainable source, cellulose-based membrane was employed as polymer matrix. Green solvent dimethylsulfoxide (DMSO) was used to replace conventional solvents. Impedance measurement using electrochemical impedance spectroscopy was performed to determine ionic conductivity of the solid polymer electrolyte membrane. Room temperature ionic conductivity of the membrane in CR2032 battery cell was 1.1×10−4 mS/cm, indicating good performance and feasibility for Li-ion battery application. This result is hundred times higher compared to cellulose-based membrane fabricated via similar route using conventional N-methyl pyrrolidone (NMP) solvent (1.38×10−6 S/cm). Further dielectric properties measurement using temperature variation in an enclosed chamber showed that the polymer electrolyte membrane obeys Arrhenius behaviour.

Dielectric and electrical properties measurement of BCTO and Co &amp; V-doped BCTO synthesized via semi-wet route method

Dielectric and electrical properties measurement of BCTO and Co &amp; V-doped BCTO synthesized via semi-wet route method

Field-induced effects in the spin liquid candidate PbCuTe2O6

${\mathrm{PbCuTe}}_{2}{\mathrm{O}}_{6}$ is considered to be one of the rare candidate materials for a three-dimensional quantum spin liquid (QSL). This assessment was based on the results of various magnetic experiments, performed mainly on polycrystalline material. More recent measurements on single crystals revealed an even more exotic behavior, yielding ferroelectric order below ${T}_{\text{FE}}\ensuremath{\approx}1\phantom{\rule{0.28em}{0ex}}\text{K}$, accompanied by distinct lattice distortions, and a somewhat modified magnetic response which is still consistent with a QSL. Here we report on low-temperature measurements of various thermodynamic, magnetic, and dielectric properties of single-crystalline ${\mathrm{PbCuTe}}_{2}{\mathrm{O}}_{6}$ in magnetic fields $B\ensuremath{\le}14.5\phantom{\rule{0.28em}{0ex}}\text{T}$. The combination of these various probes allows us to construct a detailed $B\text{\ensuremath{-}}T$ phase diagram including a ferroelectric phase for $B\ensuremath{\le}8$ T and a $B$-induced magnetic phase at $B\ensuremath{\ge}11$ T. These phases are preceded by or coincide with a structural transition from a cubic high-temperature phase into a distorted noncubic low-temperature state. The phase diagram discloses a ferroelectric quantum critical point at ${B}_{c1}=7.9\phantom{\rule{0.28em}{0ex}}\text{T}$, where the second-order phase transition line associated with ferroelectric order is suppressed to zero. In addition, a magnetic quantum phase transition is revealed at ${B}_{c2}=11\phantom{\rule{0.28em}{0ex}}\text{T}$. The corresponding phase transition to a field-induced magnetic order at $B&gt;{B}_{c2}$ is likely to be of first order. Field-induced lattice distortions, observed in the state at $T&gt;1$ K and which are assigned to the effect of spin-orbit interaction of the ${\mathrm{Cu}}^{2+}$ ions, are considered as the key mechanism by which the magnetic field couples to the dielectric degrees of freedom in this material.

Dielectric Properties of Healthy Ex Vivo Ovine Lung Tissue at Microwave Frequencies

Knowledge of dielectric properties of lung tissue is fundamental for the improvement of lung disease diagnostics and therapeutic solutions (e.g. microwave imaging and microwave thermal ablation treatment). Although lung disease rates are increasing, lung tissue remains one of the least characterized tissues due to its heterogeneity, variability in air content, and handling difficulties. In this work, dielectric properties of ex-vivo ovine lung tissue samples were measured in the frequency range 500 MHz – 8 GHz, together with measurements of sample density (air content). Different Cole-Cole models were applied to the measured dielectric properties values. The best fitting model was chosen, and results were compared with available literature. Furthermore, the dielectric property measurements were correlated with the air content of the samples. Updated Cole-Cole models for lung tissue of different density is provided in the 500 MHz – 8 GHz range. The existence of air content threshold in lung is shown. Below this limit, the properties begin to change drastically with the change in density.

The complex permittivity of PEDOT:PSS.

High permittivity materials are required for efficient organic photovoltaic devices, and the addition of the conjugated polymer composite poly(3,4-ethylenedioxythiophen) polystyrene sulfonate (PEDOT:PSS) to dielectric polymers has been shown to significantly heighten their permittivity. The permittivity of PEDOT:PSS at the optical and microwave frequencies has been investigated, but PEDOT:PSS layers are mainly used for low-frequency device applications, where accurate dielectric property measurements are hindered by their high electrical conductivity and the problems arising from the metal-polymer interfaces. Here, we determine the complex relative permittivity (εr*=εr'-jεr″) of PEDOT:PSS layers perpendicular to the layer plane in the 10-2-106 Hz range by combining data from the reactive energy estimations and electrochemical impedance spectroscopy, and discover that: εr' at <1Hz is ultra-high (∼106) decreasing with frequency to ∼5 at 106 Hz; the experimental data fit the Cole-Cole dielectric relaxation model by considering multiple relaxation mechanisms; PEDOT:PSS polarizes nonlinearly and εr' increases with the intensity of the applied external field; low frequency εr' increases with both thickness and temperature of the layer, opposite trend of temperature-dependence prevails at >103Hz; the dielectric properties of PEDOT:PSS are highly anisotropic and the in-plane εr' at 1.0kHz is three orders of magnitude higher than the vertical εr'; and that the εr'' decreases proportional to the reciprocal of frequency (1/f). The latter finding provides an explanation for the ubiquitous pink noise accompanying signals transmitted through organic conductor links. The described methodology can be adopted for investigations on other conjugated polymers.

Noninvasive measurement of head dielectric properties as a novel method for monitoring intracranial volume variations

Noninvasive measurement of head dielectric properties as a novel method for monitoring intracranial volume variations

Enhanced Power Generation by Piezoelectric P(VDF-TrFE)/rGO Nanocomposite Thin Film

In this study we fabricated a piezoelectric nanogenerator (PENG) of nanocomposite thin film comprising a conductive nanofiller of reduced graphene oxide (rGO) dispersed in a poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)) matrix that was anticipated to show enhanced energy harvest performance. For the film preparation we employed the Langmuir-Schaefer (LS) technique to provide direct nucleation of the polar β-phase without any traditional polling or annealing process. We prepared five PENGs consisting of the nanocomposite LS films with different rGO contents in the P(VDF-TrFE) matrix and optimized their energy harvest performance. We found that the rGO-0.002 wt% film yielded the highest peak-peak open-circuit voltage (VOC) of 88 V upon bending and releasing at 2.5 Hz frequency, which was more than two times higher than the pristine P(VDF-TrFE) film. This optimized performance was explained by increased β-phase content, crystallinity, and piezoelectric modulus, and improved dielectric properties, based on scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), x-ray diffraction (XRD), piezoelectric modulus, and dielectric property measurement results. This PENG with enhanced energy harvest performance has great potential in practical applications for low energy power supply in microelectronics such as wearable devices.

On the use of microwaves during combustion/calcination of N-doped TiO2 precursor: An EMW absorption study combined with TGA-DSC-FTIR results

For the first time, dielectric properties and electromagnetic wave (EMW) absorbing performance of a precursor for N-doped TiO2 nanoparticles undergoing combustion synthesis are reported. The precursor contains titania, NH4Cl as source of N atoms for TiO2 nanoparticles doping, and organics. Thermogravimetric analysis (TGA) reveals that the 180–450 °C temperature range accounts for the overall weight loss of the process. High-temperature gas evolution analysis confirms combustion of the organic component. Aiming to optimize output power and time schedule of the material’s microwave (MW) calcination, in situ high temperature dielectric properties measurements were recorded during MW irradiation in a dedicated cavity. Results revealed that after a first stage of non-combustive decomposition, in a second stage the EMW absorption decreases, so MW power is no longer necessary and hybrid heating is suggested to reach the desired calcination temperature (375–400 °C).

Dielectric Properties of Polymer Nanocomposite Interphases Using Electrostatic Force Microscopy and Machine Learning.

Knowing the dielectric properties of the interfacial region in polymer nanocomposites is critical to predicting and controlling dielectric properties. They are, however, difficult to characterize due to their nanoscale dimensions. Electrostatic force microscopy (EFM) provides a pathway to local dielectric property measurements, but extracting local dielectric permittivity in complex interphase geometries from EFM measurements remains a challenge. This paper demonstrates a combined EFM and machine learning (ML) approach to measuring interfacial permittivity in 50 nm silica particles in a PMMA matrix. We show that ML models trained to finite-element simulations of the electric field profile between the EFM tip and nanocomposite surface can accurately determine the interface permittivity of functionalized nanoparticles. It was found that for the particles with a polyaniline brush layer, the interfacial region was detectable (extrinsic interface). For bare silica particles, the intrinsic interface was detectable only in terms of having a slightly higher or lower permittivity. This approach fully accounts for the complex interplay of filler, matrix, and interface permittivity on the force gradients measured in EFM that are missed by previous semianalytic approaches, providing a pathway to quantify and design nanoscale interface dielectric properties in nanodielectric materials.