Measurement Of Properties Research Articles

A new experimental setup for the determination of drying soil–water characteristic curve and coefficient of permeability using the continuous evaporation method and osmotic tensiometers

Soil-water characteristic curve (SWCC) and coefficient of permeability (k) are amongst the most crucial soil properties in unsaturated soil mechanics for soil moisture conservation. The direct measurement and prediction of such properties are important to engineering applications, but they are complicated. This study developed a new experimental setup (the OT permeameter) using osmotic tensiometers (OTs) and the continuous evaporation method. The proposed OT permeameter could directly measure SWCC and k up to 1000 kPa suction within one to two weeks. Moreover, the proposed setup is fully automated and data processing was minimal. In addition, a new general equation has been developed to predict and best fit the unsaturated k measurement. The proposed equation uses a minimal number of parameters that carry physical meaning and provides an intuitive and easy way to predict and best-fit k measurement. The accuracy and robustness of both the proposed OT permeameter and prediction equation were evaluated using published data and experimental data from this study.

The Effect of Infiltration Rate on Flood Hazards in Gorontalo City

Infiltration rate is a measurement of the physical properties of soil. The classification of infiltration rates according to ILRI (1974) based on the results of changes by Rickard and Cossens (1965) is an important characteristic to indicate land drainage conditions. The aim of this research is to determine the classification of infiltration and its extent. The research method uses a grid system by dividing the city area into 250 m x 250 m consisting of 108 grids with 46 grids representing the lowlands. The infiltration rate in Gorontalo City as a whole is classified as very slow 2189.44Ha or 32.81%, the meaning of this percentage shows that an infiltration rate of less than 2.5 cm/hour occurs in Gorontalo City. For the infiltration rate with a slow classification, the speed is 2.5– 15 cm/hour, covering an area of 2615.38 Ha or 39.17%.

SYNTHESIS, CHARACTERIZATION, DFT, AND BIOLOGICAL ASSAY OF NEW XANTHATE COMPLEXES WITH NITROGEN BASES

This study introduces a new series of complexes and adducts, denoted by [M(2-PhOEtXant)2.nL], where M represents Mn(II), Fe(II), Co(II), or Ni(II), and the ligand (2-PhOEtXant) is 2-Phenoxyethylxanthate. Varying ligands, including pyridine, piperidine, quinoline, ethylenediamine, and (1,10)-phenanthroline, are explored based on the value of n. Comprehensive characterization, encompassing techniques like 1H-NMR, 13C-NMR, FTIR, AA, CHN analysis, UV-visible spectroscopy, and magnetic property measurements, is employed. Results indicate an octahedral geometry for these complexes, as revealed by effective magnetic moment measurements and electronic spectra analysis. The compounds exhibit noteworthy antioxidant properties, demonstrated through the DPPH radical scavenging method, highlighting their potential as effective antioxidants. Moreover, the complexes display enhanced antibacterial activity against microbial strains compared to free ligands. This research not only delves into the coordination chemistry of these complexes but also underscores their diverse applications. Combining experimental methods with computational insights using Density Functional Theory (DFT) enhances the understanding of dithiolate transition metal complexes. The alignment of computational and experimental outcomes strengthens the reliability of the findings, laying a robust foundation for interdisciplinary exploration. The identified potential applications in optoelectronics, along with the notable antioxidant and antibacterial activities, position these complexes as promising contenders for advanced technologies and scientific applications.

Micro tensile tester measurement of biomechanical properties and adhesion force of microtubule-polymerization-inhibited cancer cells

Both mechanical and adhesion properties of cancer cells are complex and reciprocally related to migration, invasion, and metastasis with large cell deformation. Therefore, we evaluated these properties for human cervical cancer cells (HeLa) simultaneously using our previously developed micro tensile tester system. For efficient evaluation, we developed image analysis software to modify the system. The software can analyze the tensile force in real time. The modified system can evaluate the tensile stiffness of cells to which a large deformation is applied, also evaluate the adhesion strength of cancer cells that adhered to a culture substrate and were cultured for several days with their adhesion maturation. We used the modified system to simultaneously evaluate the stiffness of the cancer cells to which a large deformation was applied and their adhesion strength. The obtained results revealed that the middle phase of tensile stiffness and adhesion force of the microtubule-depolymerized group treated with colchicine (an anti-cancer drug) (stiffness, 13.4 ± 7.5 nN/%; adhesion force, 460.6 ± 258.2 nN) were over two times larger than those of the control group (stiffness, 5.0 ± 3.5 nN/%; adhesion force, 168.2 ± 98.0 nN). Additionally, the same trend was confirmed with the detailed evaluation of cell surface stiffness using an atomic force microscope. Confocal fluorescence microscope observations showed that the stress fibers (SFs) of colchicine-treated cells were aligned in the same direction, and focal adhesions (FAs) of the cells developed around both ends of the SFs and aligned parallel to the developed direction of the SFs. There was a possibility that the microtubule depolymerization by the colchicine treatment induced the development of SFs and FAs and subsequently caused an increment of cell stiffness and adhesion force. From the above results, we concluded the modified system would be applicable to cancer detection and anti-cancer drug efficacy tests.

Effect of enzymatic modification on the structure and rheological properties of diluted alkali-soluble pectin fraction rich in RG-I

This study focuses on pectin covalently linked in cell walls from two sources, apples and carrots, that was extracted using diluted alkali, and it describes changes in the rheological properties of diluted alkali-soluble pectin (DASP) due to enzymatic treatment. Given DASP’s richness of rhamnogalacturonan I (RG-I), RG-I acetyl esterase (RGAE), rhamnogalacturonan endolyase (RGL), and arabinofuranosidase (ABF) were employed in various combinations for targeted degradation of RG-I pectin chains. Enzymatic degradations were followed by structural studies of pectin molecules using atomic force microscopy (AFM) as well as measurements of rheological and spectral properties. AFM imaging revealed a significant increase in the length of branched molecules after incubation with ABF, suggesting that arabinose side chains limit RG-I aggregation. Structural modifications were confirmed by changes in the intensity of bands in the pectin fingerprint and anomeric region on Fourier transform infrared spectra. ABF treatment led to a decrease in the stability of pectic gels, while the simultaneous use of ABF, RGAE, and RGL enzymes did not increase the degree of aggregation compared to the control sample. These findings suggest that the association of pectin chains within the DASP fraction may rely significantly on intermolecular interactions. Two mechanisms are proposed, which involve side chains as short-range attachment points or an extended linear homogalacturonan conformation favoring inter-chain interactions over self-association.

Br-Vacancies Induced Variable Ranging Hopping Conduction in High-Order Topological Insulator Bi4Br4.

The defects have a remarkable influence on the electronic structures and the electric transport behaviors of the matter, providing the additional means to engineering their physical properties. In this work, a comprehensive study on the effect of Br-vacancies on the electronic structures and transport behaviors in the high-order topological insulator Bi4Br4 is performed by the combined techniques of the scanning tunneling microscopy (STM), angle-resolved photoemission spectroscopy (ARPES), and physical properties measurement system along with the first-principle calculations. The STM results show the defects on the cleaved surface of a single crystal and reveal that the defects are correlated to the Br-vacancies with the support of the simulated STM images. The role of the Br-vacancies in the modulation of the band structures has been identified by ARPES spectra and the calculated energy-momentum dispersion. The relationship between the Br-vacancies and the semiconducting-like transport behaviors at low temperature has been established, implying a Mott variable ranging hopping conduction in Bi4Br4. The work not only resolves the unclear transport behaviors in this matter, but also paves a way to modulate the electric conduction path by the defects engineering.

Measurement and Characterization of the Electrical Properties of Actin Filaments

Actin filaments, as key components of the cytoskeleton, have aroused great interest due to their numerous functional roles in eukaryotic cells, including intracellular electrical signaling. The aim of this research is to characterize the alternating current (AC) conduction characteristics of both globular and polymerized actin and quantitatively compare their values to those theoretically predicted earlier. Actin filaments have been demonstrated to act as conducting bionanowires, forming a signaling network capable of transmitting ionic waves in cells. We performed conductivity measurements for different concentrations of actin, considering both unpolymerized and polymerized actin to identify potential differences in their electrical properties. These measurements revealed two relevant characteristics: first, the polymerized actin, arranged in filaments, has a lower impedance than its globular counterpart; second, an increase in the actin concentration leads to higher conductivities. Furthermore, from the data collected, we developed a quantitative model to represent the electrical properties of actin in a buffer solution. We hypothesize that actin filaments can be modeled as electrical resistor–inductor–capacitor (RLC) circuits, where the resistive contribution is due to the viscous ion flows along the filaments; the inductive contribution is due to the solenoidal flows along and around the helix-shaped filament and the capacitive contribution is due to the counterion layer formed around each negatively charged filament.

Enhancing ferroelectric characterization at nanoscale: A comprehensive approach for data processing in spectroscopic piezoresponse force microscopy

Switching Spectroscopy Piezoresponse Force Microscopy (SSPFM) stands out as a powerful method for probing ferroelectric properties within materials subjected to incremental polarization induced by an external electric field. However, the dense data processing linked to this technique is a critical factor influencing the quality of obtained results. Furthermore, meticulous exploration of various artifacts, such as electrostatics, which may considerably influence the signal, is a key factor in obtaining quantitative results. In this paper, we present a global methodology for SSPFM data processing, accessible in open-source with a user-friendly Python application called PySSPFM. A ferroelectric thin film sample of potassium sodium niobate has been probed to illustrate the different aspects of our methodology. Our approach enables the reconstruction of hysteresis nano-loops by determining the PR as a function of applied electric field. These hysteresis loops are then fitted to extract characteristic parameters that serve as measures of the ferroelectric properties of the sample. Various artifact decorrelation methods are employed to enhance measurement accuracy, and additional material properties can be assessed. Performing this procedure on a grid of points across the surface of the sample enables the creation of spatial maps. Furthermore, different techniques have been proposed to facilitate post-treatment analysis, incorporating algorithms for machine learning (K-means), phase separation, and mapping cross correlation, among others. Additionally, PySSPFM enables a more in-depth investigation of the material by studying the nanomechanical properties during poling, through the measurement of the resonance properties of the cantilever–tip–sample surface system.

Improvement of synaptic property of GeSe based CBRAM by engineering the deposition condition of switching matrix

A study of effect of deposition condition of germanium selenide (GeSe) switching layer to Conductive bridging random access memory (CBRAM) device property was conducted to enhance memory property and synaptic property. The devices deposited under the varied deposition conditions were analyzed by current distribution of each state (Low-resistance state [LRS], High-resistance state [HRS]), conduction mechanism analysis, chemical analysis, and synaptic analysis according to pulse conditions. When we deposited switching layer at lowest power (40 W), more Ag ions move to the switching matrix and make lower operation voltage. But there were some disadvantages, which were worst distribution and higher HRS current, less memory window, nonlinear and rapid increase of potentiation process. Conversely, although the device deposited at high voltage increased the operating voltage, but there are improvements, such as the highest memory window and improved linearity of potentiation. The best sample was conducted the synaptic property measurement, and the device successfully mimicked the biological synaptic property with the good linearity of potentiation and depression, spike-rate dependent plasticity (SRDP) and spike-timing dependent plasticity (STDP) properties.

Monitoring and Assessment of the Quality of Chlorinated Water in Schools

All water destined for human consumption must be subjected to disinfection processes via chlorination with the aim of eliminating the risk of the transmission of waterborne diseases. However, the treatment of water using this method leads to the formation of trihalomethanes (THMs), which are toxic compounds that may be ingested, inhaled, or absorbed by the skin, increasing the risk of carcinogenic and mutagenic processes. High trihalomethane concentrations in water may be directly related to physicochemical properties, such as temperature, pH, hardness, and potentially toxic metal concentrations. In this work, physicochemical characterization was performed and water quality was assessed with regard to the presence of trihalomethanes in 17 samples collected from points before and after storage in reservoirs. Atomic absorption spectroscopy to determine potentially toxic metals and the measurement of physicochemical properties demonstrated that all results were in accordance with the standards established by Brazilian legislation. Gas chromatography–mass spectrometry was used to determine levels of trihalomethanes in the water samples (trichloromethane, bromodichloromethane, chlorodibromomethane, and bromoform), which were also in accordance with the limits established by Brazilian legislation. Hierarchical clustering on principal components confirmed changes in the water quality depending on location. This work constitutes a paradigm for future studies on the monitoring of toxic organic compounds in water to avoid health problems in humans and animals.

Enhanced Imaging Analysis of Aggregates for Road and Railway Applications

The South African pavement community has shown a keen interest in the use of imaging techniques to characterize the morphological characteristics of aggregates used in road and railway construction. This interest arises from the need to overcome the limitations of the traditional methods currently employed to quantify the shapes of these materials. Recent advancements and the use of enhanced aggregate imaging techniques for quantifying the shapes of crushed stone and ferro slag materials from 10 sources across the country are presented in this paper. A wide range of railway track ballast and road aggregates were selected from various quarries and sources across different provinces for this study. As part of this research, an improved protocol was developed to standardize imaging acquisition and ensure the repeatability of shape property measurements, thereby providing meaningful results and facilitating data analysis. The imaging analysis conducted in this study, which involved close to 2000 aggregate particles, revealed valuable insights into the angularity, surface texture, and flat and elongated ratio properties of coarse aggregates. Preliminary specification limits for these shape properties have been established. This contribution represents an initial step toward supporting the South African road and railway industry in adopting advanced techniques for the selection of aggregate materials.

Gravity and Magnetic Joint Imaging Based on Gramian Constraints

Gravity and magnetic imaging produce numerical images proportional to the density and magnetization source distribution through the upward continuation of potential field data. However, the inherent ambiguity and non-uniqueness in gravity or magnetic imaging restrict the reliability of the imaging model. We develop a joint iterative imaging framework for gravity and magnetic data based on Gramian constraints. The imaging fields of gravity and magnetic field are initially calculated by the depth from extreme points method. With the recovered magnetization and density distribution, the gradient directions of the Gramian function for these model parameters are calculated and utilized to regularize the joint imaging directions for gravity and magnetic fields. The introduction of Gramian constraints achieves mutual complementarity of the gravity and magnetic data and generates density and magnetization models with more distinct boundaries and improved structural coherence. The proposed approach is tested by two synthetic examples and applied to field data from the Galinge iron deposit in Qinghai, China. The real case results are verified by information from drillholes and physical properties measurements of ore and rock samples. Joint imaging provides an alternative to joint inversion with improved resolution and reliability of imaging models compared to separate imaging through the complementarity of gravity and magnetic data.

Safeguarding public facilities: a study on enhancing safety in mosque amenities through slip-resistance and surface innovations

PurposeThis study critically examines the safety aspects of ablution spaces in United Arab Emirates (UAE) mosques, emphasising the evaluation of smooth ceramic tile floorings prone to water accumulation. As an integral practice in Islamic worship, ablution spaces cater to a diverse demographic, making their safety a paramount concern. This study aims to meticulously assess slip-resistance properties and surface characteristics to provide practical recommendations for enhanced safety measures.Design/methodology/approachThe investigation involves in situ measurements of traction properties and an extensive analysis of surface features in thirty mosques across the UAE. This comprehensive approach allows for identifying the unique challenges posed by ceramic tile floorings in ablution spaces. The study uses a portable tribometer for dynamic friction coefficient measurements, ensuring accurate slip-resistance evaluations. Surface texture analysis uses a portable profilometer to quantify roughness parameters.FindingsThe study’s findings significantly advance the comprehension of safety considerations in ablution spaces. Through empirical evidence and evidence-based insights, the research identifies immediate safety concerns and provides practical recommendations to create secure and inclusive environments within mosques. The emphasis lies on safeguarding the well-being of worshippers and contributing to the broader goal of safety in religious spaces.Originality/valueThe original contribution of this study lies in its dual focus on immediate safety concerns and the deeper understanding of unique safety challenges within ablution spaces. By offering evidence-based insights and practical recommendations, the research strives to make meaningful contributions to creating secure and inclusive environments within mosques.

A Long-Retention Cell Membrane-Targeting AIEgen for Boosting Tumor Theranostics.

Designing and developing photosensitizers with cell membrane specificity is crucial for achieving effective multimodal therapy of tumors compared to other organelles. Here, we designed and screened a photosensitizer CM34 through donor/receptor regulation strategies, and it is able to achieve long-retention cell membrane targeting. It is not only an extremely excellent cell membrane targeted tumor theranostic agent, but also found to be a promising potential immune activator. Specifically, CM34 with a larger intramolecular twist angle is more likely to form larger aggregates in aqueous solutions, and the introduction of cyanide group also enhances its interaction with cell membranes, which were key factors hindering molecular penetration of the cell membrane and prolonging its residence time on the cell membrane, providing conditions for further membrane targeted photodynamic therapy. Furthermore, the efflux of contents caused by cell necrosis directly activates the immune response. In summary, this study realizes to clarify and refine all potential mechanisms of action through density functional theory calculations, photophysical property measurements, and cellular level mechanism exploration, providing a new direction for the clinical development of cell membrane targeted anti-tumor immune activators.

EPOCHS Paper – VIII. An insight into MIRI-selected galaxies in SMACS-0723 and the benefits of deep MIRI photometry in revealing AGN and the dusty universe

ABSTRACT We present the analysis of the stellar population and star formation history of 181 MIRI selected galaxies at z = 0 − 3.5 in the massive galaxy cluster field SMACS J0723.3–7327, commonly referred to as SMACS0723, using the JWST Mid-Infrared Instrument (MIRI). We combine the data with the JWST Near Infrared Camera (NIRCam) catalogue, in conjunction with the Hubble Space Telescope (HST) WFC3/IR and ACS imaging. We find that the MIRI bands capture PAH features and dust emission, significantly enhancing the accuracy of photometric redshift and measurements of the physical properties of these galaxies. The median photo-z’s of galaxies with MIRI data are found to have a small 0.1 per cent difference from spectroscopic redshifts and reducing the error by 20 per cent. With MIRI data included in SED fits, we find that the measured stellar masses are unchanged, while the star formation rate is slightly lower by 0.1 dex. We also fit the median SED of active galactic nuclei (AGNs) and star-forming galaxies (SFG) separately. MIRI data provides tighter constraints on the AGN contribution, reducing the typical AGN contributions by ∼15 per cent. In addition, we also compare the median SED obtained with and without MIRI, and we find that including MIRI data yields steeper optical and UV slopes, indicating bluer colours, lower dust attenuation, and younger stellar populations. In the future, MIRI/MRS will enhance our understanding by providing more detailed spectral information and allowing for the study of specific emission features and diagnostics associated with AGN.

3D-printed short nanofibers/hydrogel-based vaginal films as a novel system for the delivery of anti-HIV microbicide drugs

Acquired immunodeficiency syndrome (AIDS) is a global epidemic that affects the lives of millions of young women, particularly those who live in poverty-stricken regions and engage in unsafe sexual behaviors, forcing the development of unique pre-exposure anti-HIV prophylaxis tools. Using a combination of antiretroviral medications with various antiviral mechanisms significantly improves the prognosis for HIV patients. The integration of 3D printing technology, short nanofiber technology, and hydrogel into a single system known as “3D-printed nanocomposites” is an emerging approach that is gaining traction in tissue engineering, regenerative medicine, and biomedical applications. Based on these foundations, the current study aims to develop, for the first time, a 3D-printed short nanofiber/film for the vaginal delivery of ritonavir and efavirenz in a fixed-dose combination. To identify an optimal 3D-printable short nanofibers/hydrogel formulation, multiple formulations, and fragmentation methods were investigated. Following that, the generated vaginal films were evaluated using several physicochemical characterizations, mechanical properties measurements, and in vitro release studies. The findings revealed that only cryocutting is effective for polycaprolactone nanofiber fragmentation. The 3D-printed short nanofibers-loaded films had an ultimate tensile strength of 6.75 ± 1.27 MPa and elongation at break of 262.67 ± 44.32 MPa, suggesting their reliability for handling and vaginal application. Furthermore, the in vitro release study demonstrated that rapid EFZ release occurred during the first 45 min, whereas RIT release lasted more than 72 h, indicating that the complex drug release profile was met. In summary, the study emphasizes that 3D printing of short nanofiber-based films is likely to be an effective platform for localized vaginal drug delivery, particularly anti-HIV therapies.

Profilometry‐Based Indentation Plastometry and Uniaxial Testing of Pipelines: Detection of In‐Plane Anisotropy and Potential for Simplification of Test Procedures

This article concerns anisotropy in stress–strain relationships exhibited by steel pipelines. Since the stress from internal pressurization is highest in the hoop direction, standard industrial practice to measure these properties has focussed on tensile testing in this direction, requiring a prior flattening operation. The associated plastic deformation may affect properties, typically causing a (poorly‐defined) degree of hardening and the creation of inhomogeneity. Field testing of such pipelines, requiring in situ measurement of tensile properties (yield stress (YS) and ultimate tensile stress (UTS)), is based on indentation testing of the outer surface. One such test (profilometry‐based indentation plastometry (PIP)), not only gives the stress–strain curve, but also allows detection of any (in‐plane) anisotropy, with a high sensitivity. Both PIP testing and compression testing (with and without prior flattening) have confirmed that none of the eight pipes examined in the current work exhibited any such anisotropy, although the effects of flattening did tend to generate apparent anisotropy in the tensile test outcomes. It may therefore be appropriate to switch the focus of tensile testing to the axial direction, such that no flattening would be required.

MgHg(SeO3)2(H2O)2: A magnesium mercury selenite with large birefringence

Selenite crystalline materials have been popular owing to the diverse structures and optical performances. A new mercury selenite, MgHg(SeO3)2(H2O)2, was synthesized by using a conventional hydrothermal method. It crystallizes in the monoclinic structure with a C2/c space group, MgHg(SeO3)2(H2O)2 exhibits a three-dimensional (3D) structure, which is made up of [Hg(SeO3)2]2–∞ chains and distorted MgO4(H2O)2 octahedra. Besides, it presents a large birefringence of 0.137 @ 546 nm according to experimental measurement. Synthesis, crystal structure, thermal stability, optical property measurements and theoretical studies were performed in this work.

Neutron scattering and neural-network quantum molecular dynamics investigation of the vibrations of ammonia along the solid-to-liquid transition

Vibrational spectroscopy allows us to understand complex physical and chemical interactions of molecular crystals and liquids such as ammonia, which has recently emerged as a strong hydrogen fuel candidate to support a sustainable society. We report inelastic neutron scattering measurement of vibrational properties of ammonia along the solid-to-liquid phase transition with high enough resolution for direct comparisons to ab-initio simulations. Theoretical analysis reveals the essential role of nuclear quantum effects (NQEs) for correctly describing the intermolecular spectrum as well as high energy intramolecular N-H stretching modes. This is achieved by training neural network models using ab-initio path-integral molecular dynamics (PIMD) simulations, thereby encompassing large spatiotemporal trajectories required to resolve low energy dynamics while retaining NQEs. Our results not only establish the role of NQEs in ammonia but also provide general computational frameworks to study complex molecular systems with NQEs.

Magnetic order in holmium and erbium formate: Parent frameworks for a potential random spin chain paramagnet

This work uses a combination of neutron diffraction and bulk property measurements to establish the low temperature magnetic states in the dense metal-organic frameworks Ho(HCO2)3 and Er(HCO2)3; whose structures feature chains of face-sharing LnO9 polyhedra packed into a triangular lattice. Below 0.7 K Ho(HCO2)3 is found to adopt a state in which the magnetic moment on its ferromagnetic chains vary from neighbouring chains but the sum around each triangle is constant. Er(HCO2)3 is found to be the first lanthanide formate to adopt an ordered magnetic state with antiferromagnetic coupling within its chains near 50 mK. The potential to combine the ferromagnetic and antiferromagnetic coupling within chains associated with Ho and Er cations, respectively, in the same compound has also been explored via the series Ho1-xErx(HCO2)3. Ho0.5Er0.5(HCO2)3 remains paramagnetic to 0.4 K, suggesting it may be a starting point to search for a random spin chain paramagnet.