Mean Mass Fraction Research Articles

Large eddy simulation of turbulent non-premixed oxy-fuel jet flames with different Reynolds numbers

Due to differences in the physical and chemical properties of CO2 and N2, along with a reduction in the momentum ratio between oxidant and fuel streams, the local extinction of oxy-fuel flames is significantly more pronounced compared to conventional air–fuel flames, which poses challenges in the design and operation of oxy-fuel burners. This study further validates the species-weighted flamelet/progress variable (FPV) model proposed in previous work [Jiang et al., 2023], particularly in oxy-fuel flames characterized by highly local extinction. Large eddy simulations were conducted on the Sandia oxy-fuel jet diffusion flame at various Reynolds numbers. The predictions are systematically compared with experimental data, and the influence of Reynolds number on local extinction is thoroughly analyzed. The results demonstrate that the numerical simulation effectively predicts mean temperature, species mass fractions, differential diffusion parameters (ZHC), and local extinction in oxy-fuel jet flames across a wide range of Reynolds numbers. The errors in predicted mean temperature and mass fractions exhibit a slight increase with rising Reynolds numbers, yet remain below 15 %. As the Reynolds number increases from 12,000 to 18,000, the predicted peak ZHC decreases by 30 %, and the beneficial effect of preferential diffusion of H2 weakens, while the adverse effect of CO2 on combustion becomes stronger.

Traceable determination of metal composition of tyres using tandem ICP-MS and benchmarking of emissions inventories.

Non-exhaust emissions are becoming of increasing significance with respect to total particulate matter (PM) concentrations in ambient air. Of particular interest is the metal content of this PM since metallic compounds are well known to have toxic effects on human health and the environment. In this study, 'bottom-up' annual tyre wear emission rates were estimated and compared to top-down' emissions declared by the UK; it was calculated that between 14 and 25 tonnes of Zn entered the atmosphere in PM10 in 2020. The emission rates were estimated using a cost-effective, simple but robust validated method for analysis of the metals in tyres using tandem inductively coupled plasma mass spectrometry (ICP-MS/MS) for the first time, involving minimal offline sample preparation. This method was applied to five different tyre makes and brands, all available for sale in the UK, and the uncertainty of each measurement was determined. Traceability was ensured in all methods and novel validation techniques were applied due to lack of available reference materials. Zn was found to be the largest metal component in all tyres with a mass fraction of approximately 10 mg g-1. The mean mass fractions of metals in the tyres decreased in the order of Zn > Al > Fe > Mg > Ti > Pb > Cu > Ba > Ni. Significant differences in composition were found between the five tyres. The relative expanded uncertainties of the metals measurements ranged from 4 to 21%, with elements of higher mass fraction resulting in lower uncertainties. These findings will contribute to assessing current and future air quality challenges and will help to inform regulation surrounding non-exhaust emissions.

Flame Surface Density and Artificially Thickened Flame Combustion Models Applied to a Turbulent Partially-Premixed Flame

The Sydney Flame provides an excellent framework for systematic analysis of premixed, partially premixed and non-premixed methane/air combustion. It represents (depending on the axial position from the fuel inlet) non-premixed, partially premixed and fully premixed combustion. We simulate the test case FJ200-5GP-Lr75-57, which represents the partially premixed mode. Large-eddy simulations (LES) are conducted using a flame surface density combustion model (FSD) using one-step chemistry and an artificially thickened flame model (ATF) with a global two-step and an analytically reduced multi-step chemistry reaction mechanism. Unity Lewis numbers are assumed (Le=1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$Le=1$$\\end{document}) at first. The FSD and ATF models are compared using the same computational mesh, numerical scheme and boundary conditions. Both models will be analysed regarding their accuracy and computational efficiency in the regime of partially premixed combustion. A comparison of the results points out the strengths and weaknesses of the FSD models. The FSD model with inclusion of flame stretch effects yields good agreement with mean experimental temperature, CO2 and H2O mass fraction distributions in contrast to the ATF model using the global two-step mechanism, which overestimates downstream temperature, CO2 and H2O mass fractions. The FSD model performs well in all regions, which are dominated first by premixed, then partially premixed and finally non-premixed combustion along the flame. The ATF multi-step chemistry shows good results only in the premixed mode region, while mean temperature, CO2 and mass fractions are overestimated in the non-premixed mode regions at higher mixture fraction values. Including differential diffusion into the transport equations improved the ATF model results in comparison with experiments. A mesh study revealed, that the ATF model performs only after mesh refinement. In particular results are improved in the non-premixed combustion region. In contrast, the FSD model is less resolution sensitive and performs very well for both meshes. An evaluation of the Wasserstein metric provides a quantitative assessment of different ATF model setups on simulation accuracy. Finally, computational times for all simulation setups are compared.

Multi-element analysis of tyre rubber for metal tracers

The purpose of this study was to identify a characteristic elemental tyre fingerprint that can be utilised in atmospheric source apportionment calculations. Currently zinc is widely used as a single element tracer to quantify tyre wear, however several authors have highlighted issues with this approach. To overcome this, tyre rubber tread was digested and has been analysed for 25 elements by ICP-MS to generate a multielement profile. Additionally, to estimate the percentage of the tyre made up of inert fillers, thermogravimetric analysis was performed on a subset. Comparisons were made between passenger car and heavy goods vehicle tyre composition, and a subset of tyres had both tread and sidewall sampled for further comparison. 19 of the 25 elements were detected in the analysis. The mean mass fraction of zinc detected was 11.17 g/kg, consistent with previous estimates of 1% of the tyre mass. Aluminium, iron, and magnesium were found to be the next most abundant elements. Only one source profile for tyre wear exists in both the US and EU air pollution species profile databases, highlighting the need for more recent data with better coverage of tyre makes and models. This study provides data on new tyres which are currently operating on-road in Europe and is therefore relevant for ongoing atmospheric studies assessing the levels of tyre wear particles in urban areas.

Age-divided mean stellar populations from full spectrum fitting as the simplified star formation and chemical evolution history of a galaxy: methodology and reliability

ABSTRACT We introduce a practical methodology for investigating the star formation and chemical evolution history of a galaxy: age-divided mean stellar populations (ADPs) from full spectrum fitting. In this method, the mass-weighted mean stellar populations and mass fractions (fmass) of young and old stellar components in a galaxy are separately estimated, which are divided with an age cut (selected to be 109.5 yr ≈3.2 Gyr in this paper). To examine the statistical reliability of ADPs, we generate 10 000 artificial galaxy spectra, each of which consists of five random simple stellar population components. Using the Penalized PiXel-Fitting (ppxf) package, we conduct full spectrum fitting to the artificial spectra with noise as a function of wavelength, imitating the real noise of Sydney-Australian Astronomical Observatory Multi-object Integral field spectrograph (SAMI) galaxies. As a result, the Δ (= output − input) of age and metallicity appears to significantly depend on not only signal-to-noise ratio (S/N), but also luminosity fractions (flum) of young and old components. At given S/N and flum, Δ of young components tends to be larger than Δ of old components; e.g. σ(Δ[M/H]) ∼ 0.40 versus 0.23 at S/N = 30 and flum = 50 per cent. The age-metallicity degeneracy appears to be insignificant, but Δlog(age/yr) shows an obvious correlation with Δfmass for young stellar components ($\mathcal {R}\sim 0.6$). The impact of dust attenuation and emission lines appears to be mostly insignificant. We discuss how this methodology can be applied to spectroscopic studies of the formation histories of galaxies, with a few examples of SAMI galaxies.

Effects of thermophoresis on high-pressure binary-species boundary layers with uniform and non-uniform compositions

Direct numerical simulations of high-pressure binary-species temporal boundary layers are performed to investigate the flow physics for three situations: (1) uniform and equal composition, (2) uniform but unequal compositions and (3) non-uniform composition. Both colder- and hotter-wall situations compared with the free stream are simulated. The working fluid is a nitrogen/methane mixture. The analysis is performed at a case-specific self-similar state. Even when the initial composition is uniform, the methane mean mass fraction decreases near the colder wall, whereas it increases near the hotter wall and the mass fraction fluctuates in the entire boundary layer. Analysis of the species-mass diffusion balance and flow structures reveal that both mass-fraction variation and fluctuations are induced by the Soret effect. When the initial composition is non-uniform and the wall is colder, the methane mean mass fraction monotonically increases from the wall akin to its initial profile. However, when the wall is hotter the mean mass fraction decreases near the wall in contrast to its initial profile, a fact traced through the species-mass diffusion balance to the Soret effect being large and enriching methane near the wall. In contrast, the direction of the Soret flux is opposite for the colder wall, thus keeping the methane concentration small. Although the initial magnitude of the difference between the wall and free-stream temperature is the same in all cases, the situation is not symmetric between colder- and hotter-wall cases; the flow structure exhibits much smaller scales when the wall is hotter than when the wall is colder.

Self-similar characteristics of underexpanded, cryogenic hydrogen and methane jets

Underexpanded, cryogenic hydrogen and methane jets were measured using laser Raman scattering diagnostic. The jets were released from 1 mm to 1.25 mm orifices for the stagnation pressure ranges of 2–6 bar and temperature ranges of 37–46 K (hydrogen) and 112–189 K (methane). Raman signals are inherently small, thus a denoising algorithm was developed to substantially reduce the noise hindering the statistical analysis of the data. The time-averaged concentration and temperature data were plotted to show a hyperbolic decay law along the jet centerline and a Gaussian distribution in the radial direction. The concentration fluctuations of the cryogenic jets are similar to those of warm jets, the centerline RMS mass fraction decays similarly to the mean mass fraction, and the highest radial concentration fluctuations appear in the shear layer. Thus, the self-similar characteristics of the cryogenic jets are comparable with room-temperature jets for the present test conditions.

Characteristic regional differences in trace element pattern of 2014 German North Sea surface Wadden sediments - A judge and assessment.

The European Marine Strategy Framework Directive (MSFD) requires good ecological status of the marine environment. This also includes the Wadden Sea located in the southeastern part of the North Sea and its chemical status of sediments. Based on results from campaigns conducted in the 1980s, 32 surface sediment samples were taken in 2014 to check whether the sampling strategy required for characterizing the trace element content in sediments is representative and to determine the degree of pollution and potential changes over the last decades. For this purpose the elemental mass fractions of 42 elements were assessed in the ≤20μm grain size fraction of the surface sediments. Based on cluster analysis a clear correlation between the element distribution and the geographical location of the sampling locations of the German Wadden Sea could be found. As a result of the principal component analysis, three sub-catchments were significantly separated from each other by the characteristic element distributions in the sediments (Norderney and Weser, Elbe and offshore areas, and North Friesland). With the help of discriminant analysis, the classification was confirmed unambiguously. Small anomalies, such as potentially contaminated sites from WWII, could be identified. This proved that the sampling strategy for sediment characterization with reference to trace elements in the Wadden Sea of the German Bight is representative. The impact of regulation and changes on the overall sediment quality is most evident when looking at the environmentally critical elements such as As, Cd, Hg, and Cr. For these elements the mean mass fractions show a significant reduction over the last three decades. Current sediments feature only slightly elevated mass fractions of Ag, Cd, Ce, Cs, Nd, Pb and Se at some sampling locations.

Distribution of per- and poly-fluoroalkyl substances and their precursors in human blood

Many studies have examined per- and poly-fluoroalkyl substances (PFASs) in human blood. However, the distribution of PFASs in human blood remains not well known, especially for perfluorooctane sulfonate (PFOS) precursors. In this study, human blood samples (n = 162) were collected from general Chinese population, and then the isomer-specific partitioning of PFASs between human plasma and red blood cells (RBCs) were investigated. Perfluorooctanoate (PFOA) and PFOS were consistently the predominant PFASs in both human plasma and RBCs. In human blood, among C4–C7 perfluoroalkyl carboxylates (PFCAs), the calculated mean mass fraction in plasma (Fp) values increased from 0.76 to 0.82 with the increasing chain length. C7–C13 PFCAs exhibited a trend of gradually decreasing mean Fp with chain length. Among PFAS precursors, 6:2 fluorotelomer phosphate diester had the highest mean Fp value (0.87 ± 0.11). Calculated Fp values of N-methyl perfluorooctanesulfonamide (N-MeFOSA) and N-ethyl perfluorooctanesulfonamide (N-EtFOSA) were 0.66 ± 0.13 and 0.70 ± 0.12, respectively. Individual branched isomers consistently had greater Fp values than their corresponding linear isomers for PFOA, PFHxS, and perfluoroctane sulfonamide. To our knowledge, this study first reports the distribution of N-MeFOSA and N-EtFOSA in human blood, contributing to the better understanding of the occurrence and fate of PFASs in humans.

CFD analysis of water vapor condensation in large containments: Numerical model, verification and validation

In the event of a loss of coolant accident (LOCA) in a Pressurized Water Reactor (PWR), large quantities of water vapor and hydrogen might be released into the containment building. Increasing pressure and the risk of hydrogen deflagration can threaten the containment integrity. Water vapor condensation on cold containment structures modifies the pressure load on the containment structures. On the one hand, the total pressure reduces due to the decrease of the water vapor content of the containment atmosphere. On the other hand, the concentration of hydrogen increases, which can reach locally the threshold of deflagration or detonation. A Computational Fluid Dynamics (CFD) model is developed and tested in order to predict transients of the pressure and the concentrations of gaseous species in reactor containments after a LOCA. Since the free volume of the containment of typical French PWRs is between 50,000 m3 and 80,000 m3, the CFD model requires significant simplifications.The physical model and its simplifications as well the implementation in the CEA OpenSource CFD code TrioCFD are described. Model tests are presented in two steps. In a first step, verification tests are discussed to show that the condensation model is implemented correctly in the CFD code. In a second step, the model is validated against experimental data of the International Standard Problem ISP47. In this benchmark, steady state conditions between vapor injection and condensation were reached experimentally in the MISTRA test containment of the CEA. In phase A of the benchmark, an equilibrium was achieved between water vapor injection and water vapor condensation on temperature controlled cold walls. One incondensable gas, namely air, was present in the test vessel. In phase B, a second incondensable gas was added to the containment atmosphere, namely helium. Both steady state situations were analyzed with the CFD model. The calculations represent well the experiment when the predominant condensation paths are modelled. It is shown that the pressure in the containment vessel as well as the mean mass fractions of water vapor and air, as well as of helium in phase B, are calculated in accordance to the experiment. The temperature in the containment is overestimated. Measured vertical profiles of the species concentrations are reproduced correctly.

Parameterization of the ambient aerosol refractive index with source appointed chemical compositions

The refractive index of ambient aerosols is widely used in the climate model and remote sensing. Traditionally, the real part of the refractive index (RRI) of the ambient aerosol is calculated from the measured mass fraction of the main inorganic components with known refractive index, without full resolving the effects of variation in the RRI of organic components, which always contribute more than 50 % of the total aerosol mass. For the first time, the ambient aerosol RRI and the aerosol chemical components were measured concurrently at a suburban site Changping, in Beijing, China. Measurements results show that the ambient aerosol ranges between 1.57 and 1.71 with a mean value of 1.66. The mean mass fractions of organic aerosol (OA), nitrate, sulfate, ammonium, and chloride to total non-refractory aerosol loading are 43.1 %, 21.9 %, 21.6 %, 13.1 %, and 0.3 % respectively. Source appointment analysis of the organic aerosol show that the fossil fuel-related OA, cooking OA, biomass burning OA, less oxidized oxygenated OA and more oxidized OOA contributes 18.0 %, 11.2 %, 4.1 %, 39.9 %, 26.7 % to the total aerosol. A new parameterization scheme of the ambient aerosol RRI, which considers the source appointed OA, is proposed based on the concurrent measurements of RRI and chemical composition. The measured and parameterized RRI shows good consistency with a correlation coefficient of 0.79 and slope of 0.98. Our measurement results reveal that a significant deviation of the calculated RRI exists without considering the variation of the RRI of the aerosol organic component. The parametrization scheme is adopted and applicable in aerosol model for bettering estimating the corresponding optical and radiative effects.

Diagnosis of Thyroid Malignancy using Levels of Chemical Element Contents in Nodular Tissue

Introduction: Thyroid benign (TBN) and malignant (TMN) nodules are a common thyroid lesion. The differentiation of TMN often remains a clinical challenge and further improvements of TMN diagnostic accuracy are warranted. The aim of present study was to evaluate possibilities of using differences in chemical elements (ChEs) contents in nodular tissue for diagnosis of thyroid malignancy. Methods: Contents of ChEs such as aluminum (Al), boron (B), barium (Ba), calcium (Ca), chlorine (Cl), coper (Cu), iron (Fe), iodine (I), potassium (K), lithium (Li), magnesium (Mg), manganese (Mn), sodium (Na), phosphorus (P), sulfur (S), silicon (Si), strontium (Sr), vanadium (V), and zinc (Zn) were prospectively evaluated in “normal” thyroid (NT) of 105 individuals as well as in nodular tissue of thyroids with TBN (79 patients) and to TMN (41 patients). Measurements were performed using a combination of non-destructive and destructive methods: instrumental neutron activation analysis with high resolution spectrometry of short-lived radionuclides and inductively coupled plasma atomic emission spectrometry. Results: It was observed that in TMN tissue the mean mass fraction of I was lower while the mean mass fractions of K, Mg, and P were higher than in both NT and TBN groups of samples. It was demonstrated that I content is nodular tissue is the most informative parameter for the diagnosis of thyroid malignancy. It was found that “Sensitivity”, “Specificity” and “Accuracy” of TMN identification using the I level in the needle biopsy of affected thyroid tissue was significantly higher than that using US examination and cytological test of fine needle aspiration biopsy. Conclusions: It was concluded that determination of the I level in a needle biopsy of TNs using non-destructive instrumental analytical method is a fast, reliable, and very informative diagnostic tool that can be successfully used as an additional test of thyroid malignancy identification.

Occurrence of per- and polyfluoroalkyl substances (PFAS) in municipal solid waste landfill leachates from western China.

Landfill leachate has been documented as a significant source of trace organic pollutants, comprising an expansive family of per- and polyfluoroalkyl substances (PFAS). This study presents the findings on the distribution of 13 perfluoroalkyl carboxylates (PFCAs) and 4 perfluoroalkyl sulfonates (PFSAs) in leachates from 6 municipal solid waste (MSW) landfills in western China. The total concentrations of 17 PFAS in sampled leachates ranged from 1805 to 43,310ng/L, and 15 compounds were detected in all samples. The short-chain compounds perfluorobutane sulfonate (PFBS, mean mass fraction 23.1%) and perfluorobutyric acid (PFBA, mean mass fraction 20.6%) were dominant. There were higher PFAS concentrations in leachates from operating landfills (mean: 12,194ng/L) compared to closed landfills (mean: 2747ng/L), but there was no significant difference between young (< 10years) and old landfills (> 10years). Moderate to weak correlations were observed between PFAS concentrations and leachate properties, e.g., TN, NH4+-N, TOC, and pH. This is the first report on the distribution of PFAS in landfill leachates from western China. The results have identified landfill leachate as an underestimated source of PFAS in the environment and have contributed to a more comprehensive evaluation on PFAS presence across China.

DIAGNOSIS OF THYROID MALIGNANCY USING TRACE ELEMENTS OF NODULAR TISSUE DETERMINED BY X-RAY FLUORESCENCE ANALYSIS

Background: Benign (TBN) and malignant (TMN) thyroid nodules are a common thyroid lesion. The differentiation of TMN often remains a clinical challenge and further improvements of TMN diagnostic accuracy are warranted. The aim of this study is to evaluate the possibilities of using differences in trace element contents (TEs) in nodular tissue to diagnose thyroid malignancies and to determine the sensitivity, specificity, and accuracy for most informative TEs in the diagnosis of TMN. Methods: Contents of TEs such as bromine (Br), copper (Cu), iron (Fe), iodine (I), rubidium (Rb), strontium (Sr), and zinc (Zn) were prospectively evaluated in “normal” thyroid (NT) of 105 individuals as well as in nodular tissue of thyroids with TBN (79 patients) and to TMN (41 patients). Measurements were performed using energy-dispersive X-ray fluorescent analysis. Results: It was observed that in TMN tissue the mean mass fractions of I and Zn were lower while the mean mass fraction of Rb was higher than in NT and TBN tissue. It was demonstrated that the I contents is nodular tissue is the most informative parameter for the diagnosis of thyroid malignancy. It was found that “Sensitivity”, “Specificity” and “Accuracy” of TMN identification using the I level in the needle biopsy of affected thyroid tissue (87±5%, 96±2% and 94±2% respectively) were significantly higher than that made using ultrasound screening and cytological test of fine needle aspiration biopsy. Conclusions: It was concluded that determination the I level in a needle biopsy of TNs using energy-dispersive X-ray fluorescent analysis, is a fast, reliable, and informative diagnostic tool that can be successfully used as an additional test of thyroid malignancy identification. Peer Review History: Received: 11 March 2022; Revised: 9 April; Accepted: 28 April, Available online: 15 May 2022 Academic Editor: Dr. Emmanuel O. Olorunsola, Department of Pharmaceutics &amp; Pharmaceutical Technology, University of Uyo, Nigeria, olorunsolaeo@yahoo.com UJPR follows the most transparent and toughest ‘Advanced OPEN peer review’ system. The identity of the authors and, reviewers will be known to each other. This transparent process will help to eradicate any possible malicious/purposeful interference by any person (publishing staff, reviewer, editor, author, etc) during peer review. As a result of this unique system, all reviewers will get their due recognition and respect, once their names are published in the papers. We expect that, by publishing peer review reports with published papers, will be helpful to many authors for drafting their article according to the specifications. Auhors will remove any error of their article and they will improve their article(s) according to the previous reports displayed with published article(s). The main purpose of it is ‘to improve the quality of a candidate manuscript’. Our reviewers check the ‘strength and weakness of a manuscript honestly’. There will increase in the perfection, and transparency. Received file: Reviewer's Comments: Average Peer review marks at initial stage: 6.0/10 Average Peer review marks at publication stage: 7.0/10 Reviewers: Prof. Dr. Hassan A.H. Al-Shamahy, Sana'a University, Yemen, shmahe@yemen.net.ye Dr. U. S. Mahadeva Rao, Universiti Sultan Zainal Abidin, Terengganu Malaysia, raousm@gmail.com

Investigation of the influence of mineral dust on airborne particulate matter during the COVID-19 epidemic in spring 2020 over China

A regional air quality model system (RAQMS) driven by the Weather Research and Forecasting model (WRF) is applied to investigate the distribution and evolution of mineral dust and anthropogenic aerosols over China in April 2020, when air quality was improved due to reduced human activity during the COVID-19 epidemic, whereas dust storms began to attack China and deteriorated air quality. A dust deflation model was developed and improved mineral dust prediction. Model validation demonstrated that RAQMS was able to reproduce PM10, PM2.5 and aerosol components reasonably well. China suffered from three dust events in April 2020, with the maximum hourly PM10 concentrations exceeding 700 μg m−3 in downwind cities over the North China Plain (NCP). Mineral dust dominated PM10 mass (>80%) over the Gobi deserts in north and west China, while it comprised approximately 30–50% of PM10 over wide areas of east China. The domain and monthly mean dust mass fractions in PM10 were estimated to be 47% and 43% over the North China Plain and east China, respectively. On average, mineral dust contributed up to 22% and 21% of PM2.5 mass over the North China Plain and east China in April 2020, respectively. Sulfate and nitrate produced by heterogeneous chemical reactions on dust surface accounted for approximately 9% and 13% of secondary inorganic aerosols (SIA) concentration over the North China Plain and east China, respectively. The results from this study demonstrated that mineral dust made an important contribution to particulate matter mass during the COVID-19 epidemic in spring 2020 over China.

Diagnosis of Thyroid Malignancy Using Chemical Elements of Nodular Tissue Determined by Neutron Activation Analysis

Thyroid benign (TBN) and malignant (TMN) nodules are a common thyroid lesion. The differentiation of TMN often remains a clinical challenge and further improvements of TMN diagnostic accuracy are warranted. The aim of present study was to evaluate possibilities of using differences in chemical elements (ChEs) contents in nodular tissue for diagnosis of thyroid malignancy. Contents of ChEs such as calcium (Ca), chlorine (Cl), iodine (I), potassium (K), magnesium (Mg), manganese (Mn), and sodium (Na) were prospectively evaluated in “normal” thyroid (NT) of 105 individuals as well as in nodular tissue of thyroids with TBN (79 patients) and to TMN (41 patients). Measurements were performed using non-destructive instrumental neutron activation analysis. It was observed that in TMN tissue the mean mass fraction of I was lower while the mean mass fractions of K and Mg were higher than in NT and TBN tissue. It was demonstrated that I content is nodular tissue is the most informative parameter for the diagnosis of thyroid malignancy. It was found that “Sensitivity”, “Specificity” and “Accuracy” of TMN identification using the I level in the needle biopsy of affected thyroid tissue was significantly higher than that using US examination and cytological test of fine needle aspiration biopsy. It was concluded that determination of the I level in a needle biopsy of TNs using non-destructive instrumental analytical method is a fast, reliable, and very informative diagnostic tool that can be successfully used as an additional test of thyroid malignancy identification.

Distinguish Thyroid Malignant from Benign Alterations using Trace Element Contents in Nodular Tissue determined by Neutron Activation and Inductively Coupled Plasma Mass Spectrometry

Background Thyroid benign (TBN) and malignant (TMN) nodules are a common thyroid lesion. The differentiation of TMN often remains a clinical challenge and further improvements of TMN diagnostic accuracy are warranted. The aim of present study was to evaluate possibilities of using differences in trace elements (TEs) contents in nodular tissue for diagnosis of thyroid malignancy. Methods Contents of TEs such as silver (Ag), aluminum (Al), boron (B),, beryllium (Be), bismuth (Bi), cadmium (Cd), cerium (Ce), cobalt (Co), chromium (Cr), cesium (Cs), iron (Fe), gallium (Ga), mercury (Hg), iodine (I), lanthanum (La), lithium (Li), manganese (Mn), molybdenum (Mo), neodymium (Nd), nickel (Ni), lead (Pb), praseodymium (Pr), rubidium (Rb), antimony (Sb), scandium (Sc), selenium (Se), samarium (Sm), tin (Sn), thallium (Tl), uranium (U), yttrium (Y), and zinc (Zn) were prospectively evaluated in nodular tissue of thyroids with TBN (79 patients) and to TMN (41 patients). Measurements were performed using a combination of non-destructive instrumental neutron activation analysis with high resolution spectrometry of short- and long-lived radionuclides (INAA-SLR and INAA-LLR, respectively) and destructive method such as inductively coupled plasma mass spectrometry (ICP-MS). Results It was observed that in TMN tissue the mean mass fractions of Be, Fe, I, Sc, and Se are approximately 1.9, 1.7, 14, 3.1, and 1.6 times, respectively, lower while the mass fraction of Ga, Mo, and Rb 62%, 51%, and 33%, respectively, higher than those in TBN tissue. Contents of Ag, Al, B, Bi, Cd, Ce, Co, Cr, Cs, Hg, La, Li, Mn, Nd, Ni, Pb, Pr, Sb, Sm, Sn, Tl, U, Y, and Zn found in the TBN and TMN groups of nodular tissue samples were similar. Conclusions It was proposed to use the I mass fraction, as well as I/Ga, I/Mo, and I/Rb mass fraction ratios in a needle-biopsy of thyroid nodules as a potential tool to diagnose thyroid malignancy. Further studies on larger number of samples are required to confirm our findings and proposals.

Diagnosis of thyroid malignancy using trace elements of nodular tissue determined by neutron activation analysis

Thyroid benign (TBN) and malignant (TMN) nodules are a common thyroid lesion. The differentiation of TMN often remains a clinical challenge and further improvements of TMN diagnostic accuracy are warranted. The aim of present study was to evaluate possibilities of using differences in trace elements (TEs) contents in nodular tissue for diagnosis of thyroid malignancy. Contents of TEs such as silver (Ag), cobalt (Co), chromium (Cr), iron (Fe), mercury (Hg), iodine (I), rubidium (Rb), antimony (Sb), scandium (Sc), selenium (Se), and zinc (Zn) were prospectively evaluated in “normal” thyroid (NT) of 105 individuals as well as in nodular tissue of thyroids with TBN (79 patients) and to TMN (41 patients). Measurements were performed using non-destructive instrumental neutron activation analysis. It was observed that in TMN tissue the mean mass fraction of I was lower while the mean mass fraction of Rb was higher than in NT and TBN tissue. It was demonstrated that I content in nodular tissue is the most informative parameter for the diagnosis of thyroid malignancy. It was found that “Sensitivity”, “Specificity” and “Accuracy” of TMN identification using the I level in the needle biopsy of affected thyroid tissue was significantly higher than that using US examination and cytological test of fine needle aspiration biopsy. It was concluded that determination of the I level in a needle biopsy of TNs using non-destructive instrumental analytical method is a fast, reliable, and very informative diagnostic tool that can be successfully used as an additional test of thyroid malignancy identification.

Optimized Grapeseed Biodiesel Production and its Effect on the CI engines Combustion Characteristics at Variable Compression Ratios

The present investigation aims at optimizing the biodiesel production of Grape seed bio-oil. Modelling proficiencies like Adaptive Neuro Fuzzy Interference System, Artificial Neural Network and Response Surface Methodology (RSM) approaches are used to assess the optimal biodiesel yield by considering the input variable parameters like molar ratio, reaction time and catalyst concentration. Two-stage transesterification process is deployed using sodium hydroxide and methanol. The RSM predicted optimized grape seed biodiesel yield was noticed as 97.62% at 1.045 g/g catalyst concentration, 1.11 hr. reaction duration and 0.2758 v/v molar ratios which were in correlation with the actual yield. Further, the obtained grape seed biodiesel is amalgamated with n-butanol (20%) and Di-ethyl carbonate (10%) to understand its efficacy on the combustion characteristics of the compression ignition engine at variable compression ratios of 17, 17.5 and 18. The outcomes including the in-cylinder pressure, rate of heat release, rate of pressure rise, cumulative heat release, mean gas temperature and mass fraction burnt of the oxygenated fuel blends were compared with straight diesel and diesel – grape seed biodiesel blends.

Measurement of Nineteen Chemical Elements in Thyroid Malignant Nodules and Thyroid Tissue Adjacent to Nodules using Neutron Activation Analysis and Inductively Coupled Plasma Atomic Emission Spectrometry

Thyroid malignant nodules (TMNs) are the most common endocrine cancer and the fifth most frequently occurring type of malignancies. The etiology and pathogenesis of TMNs must be considered as multifactorial. The present study was performed to clarify the role of some chemical elements (ChEs) in the etiology of these thyroid disorders. Thyroid tissue levels of nineteen ChEs were prospectively evaluated in malignant tumor and tissue adjacent to tumor of 41 patients with TMNs. Measurements were performed using a combination of non-destructive and destructive methods: instrumental neutron activation analysis with high resolution spectrometry of short-lived radionuclides and inductively coupled plasma atomic emission spectrometry. Results of the study were additionally compared with previously obtained data for the same ChEs in “normal” thyroid tissue. It was observed that in malignant tissue the mass fractions of Al, B, Ca, Cl, Cu, K, Mg, Mn, Na, P, S, and Si were 3.14, 4.64, 1.79, 2.26, 3.55, 1.57, 1.61, 1.57, 1.24, 2.45, 1.14, and 2.81 times, respectively, higher whereas mass fraction of I was 25.6 times lower than in the normal thyroid. In the “adjacent” group mean mass fractions of Cl and I were approximately 1.6 and 1.7 times, respectively, higher, while mean values of Ba, Ca and Sr content were 55%, 45%, and 70%, respectively, lower than in the “normal” group. In tumor Ca, Cl, Cu, K, and Sr contents were approximately 2.8, 1.4, 1.8, 1.7, and 5.4 times, respectively, higher, while I content was 43 times lower than in “adjacent” group of tissue samples. It was concluded that thyroid tissue adjacent to malignant nodules kept the main function of thyroid gland, while malignantly transformed thyroid cells lost its capacity to accumulate I. It was supposed that the excessive accumulation of Cl and I by thyroid tissue probably precede the TMNs origination and development. It was also supposed that elevated levels of Al, B, Ca, Cl, Cu, K, Mg, Mn, Na, P, S, and Si, as well as drastically reduced level of me in cancerous tissue could possibly be explored for differential diagnosis of benign and malignant thyroid nodules.