Maximum Penetration Research Articles

Statistics of Bubble Plumes Generated by Breaking Surface Waves

AbstractWe examine the dependence of the penetration depth and fractional surface area (e.g., whitecap coverage) of bubble plumes generated by breaking surface waves on various wind and wave parameters over a wide range of sea state conditions in the North Pacific Ocean, including storms with sustained winds up to 22 m s−1 and significant wave heights up to 10 m. Our observations include arrays of freely drifting SWIFT buoys together with shipboard systems, which enabled concurrent high‐resolution measurements of wind, waves, bubble plumes, and turbulence. We estimate bubble plume penetration depth from echograms extending to depths of more than 30 m in a surface‐following reference frame collected by downward‐looking echosounders integrated onboard the buoys. Our observations indicate that mean and maximum bubble plume penetration depths exceed 10 and 30 m beneath the surface during high winds, respectively, with plume residence times of many wave periods. They also establish strong correlations between bubble plume depths and wind speeds, spectral wave steepness, and whitecap coverage. Interestingly, we observe a robust linear correlation between plume depths, when scaled by the total significant wave height, and the inverse of wave age. However, scaled plume depths exhibit non‐monotonic variations with increasing wind speeds. Additionally, we explore the dependencies of the combined observations on various non‐dimensional predictors used for whitecap coverage estimation. This study provides the first field evidence of a direct relation between bubble plume penetration depth and whitecap coverage, suggesting that the volume of bubble plumes could be estimated by remote sensing.

Development and validation of large-scale gas gun experiment and its simulation for evaluating impact resistance of electronic equipment

This study aimed to develop a structural analysis method to replace and validate large-scale gas gun tests for evaluating the impact resistance of electronic equipment. By measuring projectile's deceleration through experiments and simulations, stress and strain during collisions were quantified. It was demonstrated that optimizing projectile and electronic equipment designs could enhance impact resistance. Simulation results indicated that changes in projectile velocity and head angle led to variations in maximum deceleration and penetration depth, with decreasing the head angle proving more effective in reducing maximum deceleration. Comparisons between experimental and simulation results showed good agreement, particularly in plots between maximum deceleration and target collision depth. As the head angle increased, there was a tendency for maximum deceleration to increase and target penetration depth to decrease. Comparing peak deceleration curves from gas gun tests and simulations revealed similar trends, indicating consistent results. This research provides important information for evaluating the impact resistance of electronic equipment and demonstrates that combining experiments with simulations can yield more reliable results.

Safety control strategy of spinal lamina cutting based on force and cutting depth signals

AbstractLaminectomy is one of the most common posterior spinal operations. Since the lamina is adjacent to important tissues such as nerves, once damaged, it can cause serious complications and even lead to paralysis. In order to prevent the above injuries and complications, ultrasonic bone scalpel and surgical robots have been introduced into spinal laminectomy, and many scholars have studied the recognition method of the bone tissue status. Currently, almost all methods to achieve recognition of bone tissue are based on sensor signals collected by high‐precision sensors installed at the end of surgical robots. However, the previous methods could not accurately identify the state of spinal bone tissue. Innovatively, the identification of bone tissue status was regarded as a time series classification task, and the classification algorithm LSTM‐FCN was used to process fusion signals composed of force and cutting depth signals, thus achieving an accurate classification of the lamina bone tissue status. In addition, it was verified that the accuracy of the proposed method could reach 98.85% in identifying the state of porcine spinal laminectomy. And the maximum penetration distance can be controlled within 0.6 mm, which is safe and can be used in practice.

Effect of Structural Parameters on the Jet Formation and Penetration Capability of Small Caliber Shaped Charges

Take small caliber high explosive antitank cartridge as research platform, establish 35mm diameter warhead model. Numerical simulation for the process of shaped charge jet forming and penetrating the target has been done through explosion mechanics analysis software AUTODYN. Effect of liner thickness, cone angle and charging length-diameter ratio on shaped charge jet performance has been analyzed. And the optimal combination of the structural parameters of the shaped charge has been determined by orthogonal optimum design. Results show that optimized shaped charge structure can penetrate 105mm steel target under simulation conditions and the maximum penetration depth of main charge in the explosion test is 100mm, the average value of penetration depth is 86.67mm. The minimum and average of relative error between results of static explosion test and numerical simulation are 4.76% and 17.46% respectively. The research results can provide theoretical and technical support for the optimization design and engineering application of small caliber shaped charge.

The Effect of Heat Treatment and Build Orientation on the Susceptibility of Laser Powder Bed Fusion Additively Manufactured Alloy 625 to Crevice Corrosion

This study aimed to determine the optimal heat treatment and build orientation to minimize the susceptibility of additively manufactured (AM) Alloy 625 to crevice corrosion. To accomplish this, metal-to-metal and acrylic-to-metal remote crevice assembly (RCA) experiments were performed for as-made (NT) AM, stress-relieved (SR) AM, solution-annealed AM, and solution plus stabilization-annealed AM Alloy 625 in two different build orientations. Current vs. time data from metal-to-metal RCA experiments were analyzed using commercially available statistical analysis software used to perform analysis of variance. While there was a lack of statistical evidence that build orientation affects crevice corrosion susceptibility, there was strong evidence heat treatment affects crevice corrosion susceptibility. Specifically, according to Tukey’s Multiple Comparison, alloys that were heat treated had a statistically significant lower charge passed as compared to the NT specimens. This finding was consistent with measured penetration depth where NT AM specimens had the largest maximum penetration depth. In contrast, acrylic-to-metal RCAs were used to calculate crevice corrosion current density (rate) and repassivation potential. While current densities for the AM materials were comparable, the forward motion of the active crevice corrosion front on the NT and SR specimens was found to be slow, resulting in high damage accumulation locally. Both metal-to-metal and acrylic-to-metal RCA results are discussed within the context of nonhomogenized microstructures associated with AM.

Assessment of different irrigation techniques on the penetration depth of different sealers into dentinal tubules by confocal laser scanning microscope: An in vitro comparative study.

The effective disinfection of the entire root canal system aids in the penetration of irrigants into the dentinal tubules further improving sealer penetration and achieving a three-dimensional seal in endodontically treated teeth. Various final irrigation techniques can be employed to achieve this goal. Therefore, this study intended to assess and compare the efficacy of three final irrigation techniques on the depth of penetration of two root canal sealers into dentinal tubules using confocal laser scanning microscope (CLSM). Forty-eight single-rooted mandibular premolars were selected and decoronated to a length of 12 mm. All the samples were prepared using ProTaper Gold rotary files and divided into three groups: Group 1 - Conventional syringe irrigation (CSI), Group 2 - passive ultrasonic irrigation (PUI), and Group 3 - Pro-agitator tip system (PATS). Each group was divided into two subgroups: Subgroup A - AH Plus and Subgroup B - GuttaFlow Bioseal (GFB). Then, sealers were mixed with 0.1% rhodamine B dye and the samples were obturated. All the samples were sectioned at 2 mm and 5 mm from the apex and visualized under confocal laser scanning microscope (CLSM) (10×) for maximum mean penetration depth and percentage of sealer penetration. Statistical analysis was done using the independent t-test and one-way analysis of variance test, followed by Tukey's Post hoc analysis. PUI performed better in the apical third, whereas PUI and PATS showed comparable results in the middle third for both depth and percentage of sealer penetration. Among the two sealers, GFB performed better than AH Plus in both the apical and middle third. These values were statistically significant. (P < 0.05). Final irrigation activation with PUI or PATS can significantly improve sealer penetration. The average depth of penetration of GFB both at the middle and apical third of the root was significantly superior to AH Plus.

Multi-layer solid-state ultrasonic additive manufacturing of aluminum/copper: local properties and texture

Ultrasonic additive manufacturing (UAM) is an advanced joining technique that utilizes ultrasonic vibrations to bond layers of metal foil together. UAM offers several benefits over traditional manufacturing methods, including enhanced design flexibility and reduced material waste, and its potential applications in various industries such as aerospace, automotive, and biomedical engineering are being actively explored. The study employs a nanoindentation apparatus to investigate the effect of the UAM process on the local mechanical properties of the bonded interface, along with changes in microstructure, which were investigated using scanning electron microscopy and electron back-scattered diffraction. The results revealed a significant correlation between material hardness and local plasticity. EBSD has revealed that the grain size distribution of Al far from the interface contains 57% of the grains less than 3 µm in size, while at the interface this number rises to approximately 78%, indicating that the average grain size decreases as it approaches the interface. This result is consistent with nanoindentation results that demonstrated a gradual change in the hardness of Al foil far from the interface to close to the interface (the maximum penetration depth near the interface was 500 nm less than far from the interface). Both EBSD and nanoindentation disclose the effect of work hardening close to the interface, which is related to dislocation accumulation with a density of 8.6×10-10cm-2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$8.6\ imes {10}^{-10} {{\ ext{cm}}}^{-2}$$\\end{document} beneath the interface. The consistency of hardness and Young’s modulus with the pole figures and microscopic images demonstrated that plasticity flow and fine grain distribution would only occur in the vicinity of the interface in the softer metal region. Although the harder metal did not exhibit plasticity or recrystallization, the hardness, and Young’s modulus map indicated the formation of a layer of small grains close to the interface on the aluminum side owing to strain hardening and dynamic recrystallization.

Dynamic laser ignition characteristics of solid fuel and oxygen for hybrid rocket system

The transient laser ignition process in a slab burner that is similar to hybrid rocket motors is investigated in this study. The coupling characteristics between solid fuel properties, pyrolysis rate, and laser power were analysed. The results show that the laser ignition process can be divided into four stages: preheating, pyrolysis, ignition, and combustion, with the preheating and pyrolysis stages primarily controlled by the solid heating rate and the mixing characteristics in the fuel-rich combustion zone. Meanwhile, the ignition and combustion stages were characterized by ignition kernel growth and flame front propagation. The ignition delay time and the establishment of steady-state combustion were significantly affected by the ignition energy and fuel properties, i.e., The ignition delay time increases exponentially with decreasing laser energy. An increase in oxidizer flow flux reduces the demand for mixing during ignition, but the corresponding increase in combustion pressure poses challenges to the ignition process. A two-dimensional transient numerical model was established based on optical-thermal coupling theory to further understand the dynamic pyrolysis process of solid fuel particles. The model was validated through fire experiments under different laser ignition energy conditions. The results indicate that the deviation of the maximum penetration depth and ignition delay time between the experiment and the simulation is within 7 %.

Comparative evaluation of the efficacy of various irrigating techniques by checking the depth of penetration of the sealer- An in-vitro study

Sonic irrigant activation has gained widespread popularity among general dentists and endodontists currently. It is usually seen that sonic powered flosser which we have used in our study is in use in many dental colleges by post graduate students as it is construed to be the cheaper version of Endoactivator.To investigate the efficacy of sonic powered flosser with various irrigating techniques by checking the depth of sealer penetration. Forty five single-rooted teeth were instrumented and divided into 3 groups of 15 teeth each, as Group 1: endoactivator; Group 2: powered sonic flosser; Group 3: manual dynamic irrigation. The samples were obturated with AH Plus sealer labelled with Rhodamine B dye. The teeth were sectioned and viewed under confocal microscope to determine the depth of sealer penetration.Statistical analysis used: One way Anova F test was used for overall comparison among three groups and Tukey's post hoc test were used to evaluate the efficiency levels between groups. P value less than 0.05 was considered significant for all statistical test. The results showed that the maximum penetration was exhibited by endoactivator followed by manual dynamic irrigation and least by powered sonic flosser. The middle third showed the maximum penetration, followed by apical third in all the groups. Sonic powered flosser and manual agitation weren’t found to be as effective as Endoactivator, so in the absence of Endoactivator, sonic and manual agitation can’t be relied upon for desired results. The agitation of the irrigants is found to be most effective with endoactivator in order to achieve appreciable sealer penetration.So using sonic powered flosser will not be able to render the results as good as endoactivator.

Grid‐side flexibility assessment based on security distance of dispatchable region for AC/DC hybrid system using approximate second‐order cone relaxation

AbstractThe rapid growth of offshore wind power has resulted in a mismatch between generation and demand because of its variability. To quantify the maximum wind power penetration of the transmission network, the dispatchable region is defined as the largest region in the uncertainty space. The security distance is defined as the minimum distance from the operating point to the boundaries of the dispatchable region. System operators can use security distance as a metric to assess the flexibility of the power system. This paper proposes a method to construct the dispatchable region for the AC/DC hybrid system with VSC‐HVDC by outer convex relaxation firstly. The second‐order cone relaxation is employed to reformulate non‐convex and non‐linear power flow equations. Next, a polyhedral approximation is adopted to obtain the convex hull of the dispatchable region. Subsequently, an efficient algorithm known as adaptive constraint generation (Ad‐CG) is introduced to calculate the boundaries of the dispatchable region. Furthermore, solving the Chebyshev centre problem determines the minimal security distance. The modified IEEE 5‐bus and 39‐bus system is used for validating effectiveness of the proposed method and evaluating the impact of the converter reactive power compensation capacity and generation dispatch on the dispatchable region.

EV Integration-Oriented DC Conversion of AC Low-Voltage Distribution Networks and the Associated Adaptive Control Strategy

Driven by carbon-neutral targets and transportation electrification, the widespread use of electric vehicles (EVs) has become an irreversible trend. However, low-voltage distribution networks (LVDNs) can face several challenges under the high-penetration EV integration, including overloads, voltage violations and unbalance issues. In this paper, an EV integration-oriented DC conversion scheme and the associated adaptive control method for LVDNs is proposed, aiming at releasing more capacity for EVs and collaborative improvement of the above issues caused by EV charging. Based on analyzing the influence of different charging piles connected to the AC and DC LVDNs, a DC conversion scheme for three-phase four-wire LVDNs under high-penetration EVs is proposed. The voltage source converter (VSC) control strategies aimed at alleviating the overload of the DTs, voltage violations, and three-phase unbalance are designed separately based on the modified three-phase four-wire voltage sensitivity. Then, a coordinated adaptive control strategy of on-load tap changer and VSCs is proposed considering the simultaneous occurrence of multiple power quality issues in hybrid AC/DC LVDNs. Case study verifies the effectiveness of the proposed DC conversion and adaptive control methods, by which the maximum EV penetration of the hybrid AC/DC LVDN is increased from 85% to 215% compared with the AC LVDN.

Assessment of photovoltaic generation penetration effect on the maximum loadability of the system

This paper proposed a method to investigate the effect of increasing PV penetration on the voltage stability of an IEEE 14-bus test system considering maximum PV penetration and system loadability limit. The critical bus of the test system has been decided based on nose curve analysis. The solar PV system is deployed with the most critical bus of the system. The effect of increasing PV penetration on the improvement in the loading capacity of various power system components like transmission lines, transmission line transformers, and generators is investigated over the adopted test system. Based on solar PV penetration up to 100 MW, the maximum loadability limit of the IEEE 14-bus test system increases, as shown by the results. Bus 14 is found to be the most severe bus of the test system using the continuation power flow (CPF) method. However, in some cases, overloading situations develop after a certain limit of PV penetration in the power system. In this condition, the overloading of the power system equipment is improved by the use of a Static Synchronous Compensator (STATCOM) at bus number 14, a double circuit line in the critical line (9–14), and Static Synchronous Series Compensator (SSSC) in the most severe line (9–14) in the system. The maximum loadability of the system gets maximum enhanced from 4.0349 p.u. to 4.5602 p.u. under simultaneous use of solar PV generation, SSSC, and STATCOM at the most critical bus and in most severe line of the system. As evidence, the enhancement in maximum loadability of the system found using the proposed method has been also compared with the existing research. The maximum system loadability has been also enhanced under normal and (N-1) contingency conditions by the use of PV penetration in the system. PSAT/MATLAB software is used for simulation and maximum loadability has been investigated by continuation power flow (CPF) method.

Widespread Thalassinoides facies from the upper Silurian of South China: A case study from the northwestern Hunan Province, middle to upper Yangtze Block

The upper Silurian of South China records the first, and perhaps the only occurrence of widespread (spanning over 1400 km), thick to very thick bedded Thalassinoides facies (TVTFs) after the Late Ordovician mass extinction. However, the palaeobiological, palaeoecological features and potential significance of these facies are yet to be demonstrated. A case study at northwestern Hunan Province, middle to upper Yangtze Block, reports the occurrence of TVTFs in a storm dominated open marine succession of the upper Silurian Xiaoxi Formation, which can be further assigned to lower offshore, upper offshore, offshore transition to distal lower shoreface, and proximal lower to middle shoreface settings. The regular changes of bioturbation intensity and maximum penetrating depth from various settings suggest that local energy levels, especially frequency of storms could have controlled the development of Thalassinoides, while their burrow sizes were generally confined by population densities. The Thalassinoides facies could have been constructed by unknown crustaceans, which generally conducted a deposit-feeding strategy. The return of widespread TVTFs in the tropical oceans of South China during the late Silurian could reflect a restored primary productivity, an elevated oxygen level, and a final recovery of benthic ecosystem to pre-extinction level after the Late Ordovician mass extinction. TVTFs could have remarkably shaped the late Silurian benthic environment in view of their high abundance, large burrow sizes, nature of deep tiered burrow systems and a deposit-feeding strategy.

Scratch performance of natural rubber and natural rubber composites reinforced with nylon, kevlar, and carbon fabrics

The scratch performance of natural rubber (NR) and fibre-reinforced NR was investigated using a scratch test with acoustic emission (AE). Both maximum penetration depth and maximum tangential force were characterised by two procedures. Procedure 1 applied the corner of a steel cube at face leading orientation. Procedure 2 applied a steel pyramid indenter with a spherical tip at the edge leading orientation. AE was adopted in Procedure 2 for evaluation of cutting damage mode that varied from ploughing/tearing the matrix to cutting both the matrix and fabric. The scratched regions of all specimens were observed using an optical microscope to estimate the damage level and examine damage mechanisms. The results show that scratch resistance improved as fibre content and fibre stiffness increased. The maximum tangential force depended on the damage modes. Two or more fabric layers could further increase penetration resistance, but the damage level is more serious in most cases.

Numerical simulation study of the effect of nonlinear side blowing on the flow of gas-liquid two-phase flow

Abstract The hydrodynamic and stirring characteristics of gas-slag-copper matte three-phase in side-blowing melt pool melting were numerically simulated using a combination of the volume of fluid (VOF) model in computational fluid dynamics and the realizable k-ε turbulence model. The study obtained macroscopic flow and gas-liquid two-phase distribution information of the flow field in the melting process. It also examined the effects of isokinetic blowing and nonlinear blowing on the fluid velocity, penetration depth, gas content, and turbulent eddy volume of the flow field, and compared the results. The results indicate that, for the same total gas volume, constant velocity blowing (CVS) inadequately agitates the molten pool, resulting in a large stirring dead zone within the flow field. In contrast, nonlinear blowing enhances the fluid velocity overall. Specifically, sinusoidal variable speed blowing (SWS) and rectangular variable speed blowing (RWS) reduce the stirring dead zone area by 79 and 73.5 %, respectively. This is attributed to the increase in maximum penetration depth and slag phase gas content, as well as the decrease in gas escape during nonlinear blowing. The vortex volume over the total calculated time for the three conditions is enhanced by 6.7 and 1.1 % for SWS and RWS, respectively. Additionally, the turbulent kinetic energy of the fluids is increased by 18.7 and 17 %, respectively.

Evaluating the dissolution corrosion resistance of Hastelloy exposed to liquid lead‐bismuth eutectic at 500°C

AbstractThe present study investigated the dissolution and oxidation corrosion behaviors of Hastelloy exposed to static liquid lead‐bismuth eutectic (LBE) at 500°C with an oxygen concentration of 1 × 10−6 mass%. Hastelloy exhibited better LBE corrosion resistance than the Monel alloy. Both dissolution and oxidation corrosion were observed in Hastelloy, and the maximum LBE penetration depth and spinel layer thickness in the corroded sample after 4000 h of exposure reached 120 ± 36 and 21 ± 12 µm, respectively. Annealing twin boundaries provided favorable paths of accelerated LBE penetration into the matrix, resulting in selective leaching of Ni. Microstructural characterization revealed that the spinel layer formed between penetrated LBE and base metal slowed down the elemental interdiffusion, thereby retarding the dissolution rate. Volumetric changes induced by LBE penetration promoted the formation of stacking faults and dislocations, which could provide more channels for elemental diffusion, leading to the propagation of dissolution attack.

PUNCHING THIN DISCS. PART 3. INVESTIGATION OF THE FINAL STAGE OF THE INTRODUCTION OF CENTRAL PUNCH

A mathematical description of the final stage of the introduction of the central punch in the course of obtaining large thin disks or disks from hard-to-deform materials by plastic deformation is obtained. The maximum penetration force of the central punch was found at the moment of completion of the deformation process.

Transition of Edney shock–shock interactions due to the whipping phenomenon of liquid jet in supersonic crossflow

In this paper, we experimentally study the unsteady dynamics of shock–shock interaction between the bow shock generated by a liquid jet in supersonic crossflow (LJISC) and an oblique shock. Images of shock–shock interactions were captured using high-speed focusing schlieren. Due to the whipping nature of the liquid jet, a coupling happens between the instantaneous bow shock shape and violent oscillations of the liquid jet. Proper orthogonal decomposition reveals that the dominant coherent structures of LJISC are convective and flapping modes, and these modes are responsible for unsteady variation in the local bow shock angle. An oblique shock emanating from a wedge is made to interact with the oscillating bow shock of a liquid jet near the sonic line. At this shock interaction location and for a constant momentum flux ratio between liquid jet and crossflow, unsteady transitions between the types of Edney shock–shock interactions were observed. The types of Edney shock–shock interactions that can occur depend on the local average bow shock angle and the momentum flux ratio. Support vector machine (SVM) model was used to classify three types of Edney shock–shock interactions based on ten features related to the nearest knee point, shock interaction point, and maximum penetration height. Using the SVM model, three dominant features that affect the type of shock–shock interaction were identified. Experimental results, when compared with shock polar, reveal some short-duration abnormal presence of overall regular interaction instead of overall Mach interaction regime.

Statistics of maximum photon penetration depth in a two-layer diffusive medium.

We present numerical results for the probability density function f(z) and for the mean value of photon maximum penetration depth ‹zmax› in a two-layer diffusive medium. Both time domain and continuous wave regime are considered with several combinations of the optical properties (absorption coefficient, reduced scattering coefficient) of the two layers, and with different geometrical configurations (source detector distance, thickness of the upper layer). Practical considerations on the design of time domain and continuous wave systems are derived. The methods and the results are of interest for many research fields such as biomedical optics and advanced microscopy.

Evaluation of disposable protective garments against epoxy resin permeation and penetration from anti-corrosion coatings.

Epoxy-based resin formulations are a frequent cause of allergic and irritant contact dermatitis in the construction and painting industries. Cases of epoxy resin contact dermatitis continue to persist across many sectors and are likely attributable to the growing use of epoxy products, including epoxy-based anti-corrosion coatings and inadequate skin protection. There are no published performance data against epoxy resins for garment materials and gloves to guide proper material selection in the workplace. The objective of this study was to evaluate the resistance of 5 protective garment materials against permeation and penetration by bisphenol A diglycidyl ether and its higher oligomers found commonly in epoxy-based anti-corrosion coatings. Five disposable garment materials were evaluated for resistance to bisphenol A diglycidyl ether monomers and oligomers during contact with epoxy-based anti-corrosion coatings, including latex gloves, nitrile gloves, Tyvek coveralls, polypropylene/polyethylene (PP/PE) coveralls, and a cotton T-shirt. A permeation test cell system was used to evaluate each garment material against an epoxy-based zinc-rich primer and an epoxy-based intermediate coating using a realistic application method. Glass fiber filters were used to collect permeating and penetrating epoxy resin during a 120-min test period. Bisphenol A diglycidyl ether quantification was performed with high-performance liquid chromatography-electrospray ionization-tandem mass spectrometry. Paint loading, coating thickness, and homogeneity were assessed on polytetrafluoroethylene filters sprayed in series in permeation test cells. Latex gloves provided the least resistance to permeation by BADGE in coating formulations, with a maximum cumulative permeation over the 2-h test interval of 21.7 ng cm-2 with the primer and 513.8 ng cm-2 with the intermediate coating product. Nitrile gloves were not permeated by either coating formulation. The Tyvek coveralls provided greater protection as compared to the PP/PE coveralls. The cotton T-shirt was penetrated by bisphenol A diglycidyl ether more frequently than any of the tested garment materials and resulted in a maximum cumulative penetration of 128 ng cm-2 with the primer and 28.0 ng cm-2 with the intermediate coating. Although all the garment materials evaluated during this study provided sufficient protection to prevent cumulative permeation in excess of the established acceptable permeation thresholds, the use of nitrile gloves and Tyvek coverall is highly recommended to minimize skin exposure to bisphenol A diglycidyl ether. We recommend cotton T-shirts to be used under Tyvek coveralls as a secondary layer of skin protection and for added comfort, but not as a primary protection layer.