Maximum Output Research Articles

Coherent beam combining of two all-PM thulium-doped fiber chirped pulse amplifiers

In this paper, we report a coherent beam combining (CBC) system that involves two thulium-doped all-polarization maintaining (PM) fiber chirped pulse amplifiers. Through phase-locking the two channels via a fiber stretcher by using the stochastic parallel gradient descent (SPGD) algorithm, a maximum average power of 265 W is obtained, with a CBC efficiency of 81% and a residual phase error of λ/17. After de-chirping by a pair of diffraction gratings, the duration of the combined laser pulse is compressed to 690 fs. Taking into account the compression efficiency of 90% and the main peak energy proportion of 91%, the corresponding peak power is calculated to be 4 MW. The laser noise characteristics before and after CBC are examined, and the results indicate that the CBC would degrade the low frequency relative intensity noise (RIN), of which the integration is 1.74% in [100 Hz, 2 MHz] at the maximum combined output power. In addition, the effects of the nonlinear spectrum broadening during chirped pulse amplification on the CBC efficiency are also investigated, showing that a higher extent of pulse stretching is effective in alleviating the spectrum broadening and realizing a higher output power with decent combining efficiency.Graphical

Very early fractures of the stylet-driven Biotronik Solia lead used for left bundle branch area pacing

Abstract Introduction Left bundle branch area pacing (LBBAP) has become increasingly popular due to the relatively simple implantation procedure allowing for conduction system pacing (CSP). Initially, lumen-less leads have been used primarily for CSP. However, several authors have published encouraging results using conventional stylet-driven pacemaker (PM) leads as well and our centers have largely adopted this approach. Methods In our two tertiary referral centers, we assessed all patients, who underwent a LBBAP lead implantation using any lead. We observed several early lead fractures, exhibiting a unique failure mechanism, which we illustrate in this case-series. Results Between January 2022 and November 2023 343/393 patients (87.3%) were implanted with a Solia pacemaker lead, 46/393 (11.7%) received a SelectSecure 3830 lead, and 4/393 (1.0%) another stylet-driven lead. Three patients (0.8%) who initially were implanted with a Solia lead experienced very early intracardiac lead fractures within 1, 11 and 13 months after implantation despite good initial electrical performance values (Table shows initial values and values during the time of failure (bold)). The first case was a 54 year-old woman with permanent 3d degree AV block receiving an LBBAP lead after lead extraction. Four weeks later, she presented with presyncope and exit block at maximum output in uni- and bipolar configuration. The second case was a 72 year-old man with intermittent 3rd degree AV block in the context of an ischemic heart disease. He received a dual-chamber LBBAP PM. 13 months after the implantation, a bipolar impedance > 2’500Ω and exit block were noted. The third case was 65 year-old man suffering from sick sinus syndrome. He initially underwent a dual-chamber PM implantation in 2011 and due to ventricular sensing issues a transvenous lead extraction and implantation of a LBBAP lead in October 2022. During device follow-up after 11 months, a fractured LBBAP lead with bipolar impedance >2’500Ω and exit block during threshold testing was noticed. In all cases, X-rays and macroscopic analysis consistently showed a disintegration of the lead immediately distal to the ring electrode (Figure; site of fracture marked with an arrow). Most likely, this was caused by the repetitive shear stress at the hinge point of the lead where it is entering the septum. Conclusion No dedicated stylet-driven CSP lead is available to date. The implantation site and technique for LBBAP may exert higher mechanical stress on the distal part of the lead, making it more prone to fracture than in a conventional position. Currently, the use of conventional stylet-driven leads is still off-label and the performance of such leads should be monitored closely.TableFigure

Spectroscopy and efficient dual-wavelength laser performances of a Nd:GYSAG crystal

We reported on the spectral properties and dual-wavelength laser performances of a novel, to the best of our knowledge, Nd:Gd1.8Y1.2ScAl4O12 (Nd:GYSAG) crystal for the first time. The absorption spectra, emission spectra, and fluorescence lifetime were systematically investigated. Further, a continuous-wavelength (CW) laser output power up to 5.02 W was obtained under an absorbed pump power of 9.45 W with slope and optical-to-optical efficiencies of 59.4% and 53.1%, respectively, at 1061.2 and 1063.2 nm. A stable passively Q-switched (PQS) laser employing Cr:YAG as a saturable absorber (SA) was realized. The maximum average output power of 0.756 W with a slope of near 34.4% was obtained with the pulse width, pulse energy, and peak power of 14.0 ns, 128.1 µJ, and 9.15 kW, respectively. The results indicate that the Nd:GYSAG crystal is an excellent laser medium for generating a high-efficiency dual-wavelength laser and has potential in terahertz (THz) laser generation.

Tuning ZnO-based piezoelectric nanogenerator efficiency through n-ZnO/p-NiO bulk interfacing

ZnO based piezoelectric nanogenerators (PENG) hold immense potential for harvesting ambient vibrational mechanical energy into electrical energy, offering sustainable solutions in the field of self-powered sensors, wearable electronics, human–machine interactions etc. In this study, we have developed flexible ZnO-based PENGs by incorporating ZnO microparticles into PDMS matrix, with ZnO concentration ranging from 5 to 25 wt%. Among these, the PENG containing 15 wt% ZnO exhibited the best performance with an open-circuit output voltage/short-circuit current of ~ 42.4 V/2.4 µA. To further enhance the output performance of PENG, p-type NiO was interfaced with ZnO in a bulk hetero-junction geometry. The concentration of NiO was varied from 5 to 20 wt% with respect to ZnO and incorporated into the PDMS matrix to fabricate the PENGs. The PENG containing 10 wt% NiO exhibits the best performance with an open-circuit output voltage/short-circuit current of ~ 65 V/4.1 µA under loading conditions of 30 N and 4 Hz. The PENG exhibiting the best performance demonstrates a maximum instantaneous output power density ~ 37.9 µW/cm2 across a load resistance of 20 MΩ under loading conditions of 30 N and 4 Hz, with a power density per unit force and Hertz of about ~ 0.32 µW/cm2·N·Hz. The enhanced output performance of the PENG is attributed to the reduction in free electron concentration, which suppresses the internal screening effect of the piezopotential. To assess the practical utility of the optimized PENG, we tested the powering capability by charging various commercial capacitors and used the stored energy to illuminate 10 LEDs and to power a stopwatch displays. This work not only presents a straightforward, cost-effective, and scalable technique for enhancing the output performance of ZnO-based PENGs but also sheds light on its underlying mechanism.

A novel layered cobalt oxide Ba2Co9O14 as an efficient and durable bifunctional oxygen electrocatalyst for rechargeable zinc-air batteries

In this work, a layered cobalt oxide Ba2Co9O14 (BCO), belongs to a Ban+1ConO3n+3(Co8O8) family composed by alternating CdI2 based layers (Co8O8) with n (111) perovskite blocks (Ban+1ConO3n+3), has been developed as a potential bifunctional oxygen electrocatalyst candidate for efficient and durable rechargeable zinc-air battery (ZAB) application. Because of the greatly increased the specific surface area caused by ball-milling, the as-milled BCO material exhibits strongly enhanced bifunctional electrocatalytic activity towards oxygen reduction and oxygen evolution reaction in alkaline medium. Moreover, the assembled BCO-based ZAB yields an effectively improved maximum output power density of 166 mW cm−2, a considerable specific capacity of 789 mAh g−1, and excellent charge-discharge cycle stability of over 250 h at 10 mA cm−2 with over 1500 cycles.

High-power and narrow-linewidth nanosecond pulsed intracavity crystalline Raman laser operating at 1.7 µm

We report on a high-power and narrow-linewidth nanosecond pulsed intracavity crystalline Raman laser at 1.7 µm. Driven by an acousto-optically Q-switched 1314 nm two-crystal Nd:YLF laser, the highly efficient cascaded YVO4 Raman laser at 1715nm was obtained within the well-designed L-shaped resonator. Thanks to the absence of spatial hole burning in the stimulated Raman scattering process, significant spectral purification of second-Stokes radiation was observed by incorporating a fused silica etalon in the high-Q fundamental cavity. Under the repetition rate of 4 kHz, the highest average output power for single longitudinal mode operation was up to 2.2 W with the aid of precision vibration isolation and precision temperature controlling, corresponding to the pulse duration of ∼2.8 ns and the spectral linewidth of ∼330 MHz. Further increasing the launched pump power, the second-Stokes laser tended toward be always multimode, and the maximum average output power amounted to 4.8 W with the peak power of ∼0.8 MW and the spectral linewidth of ∼0.08 nm. The second-Stokes emission was near diffraction limited with M2 < 1.4 across the whole pump power range.

Synergistic Optimization of Europium‐Doped Yttria for Photoluminescence and Triboelectric Nanogenerator Applications

In recent years, multifunctional applications of the same material have gained wide recognition in various fields. The present study reports the synthesis, characterization, and multifunctional applications of europium (Eu)‐doped yttrium oxide (Y2O3) nanophosphor. Synergistic optimization of Eu‐doped Y2O3 results in enhanced photoluminescence (PL) and triboelectric nanogenerator (TENG) performance. Eu‐doped Y2O3 nanophosphors are synthesized using an autocombustion method, and comprehensive characterizations are conducted. The investigations indicate that the Eu doping significantly influences the PL intensity, with the highest emission observed at 3 mol% for powders. The synthesized nanophosphors are blended with silicone to fabricate hybrid films, which are utilized for energy harvesting applications using TENG technology. The TENG devices fabricated with these hybrid films demonstrate a notable relationship between the Eu concentration and the electrical output, achieving peak performance at 1 mol% Eu doping. The maximum output voltage of ≈535 V, short‐circuit current of ≈38 μA, and power density of 800 mW m−2 are observed. Further, TENG is demonstrated in a self‐powered UV photodetector application. The present results contribute to the improvement of sustainable energy technologies and open up a new window for multifunctional materials.

All-PM Yb-doped mode-locked fiber laser with high single pulse energy and high repetition frequency

We demonstrate an all-polarization-maintaining (PM) ytterbium (Yb)-doped fiber laser with a figure-of-9 structure to generate mode-locked pulses with high single pulse energy and high repetition frequency. By exploiting the nonlinear amplifying loop mirror, a stably self-started mode-locking is achieved with a spectrum bandwidth of 13 nm and a pulse duration of 4.53 ps. The fundamental frequency is 97.966 MHz at the maximum output power of 143 mW in single pulse mode-locked operation, corresponding to the single pulse energy is 1.46 nJ. The output pulses maintain both high repetition frequency and high single-pulse energy. This laser oscillator can be an ideal seed source for applications such as high-energy amplifiers.

A hybrid wave vibration energy harvester with electromagnetic double-speed and piezoelectric up-frequency driven by a rotating ball

The energy crisis and environmental pollution have driven the development of ambient energy harvesting technologies, and ocean waves usually contain abundant vibration energy, making the study of wave energy harvesting technology of profound value. This paper proposes a hybrid wave vibration energy harvester with electromagnetic double-speed and piezoelectric up-frequency driven by a rotating ball. For the electromagnetic generator (EMG), the excitation magnet and coil move simultaneously, resulting in double the flux variation rate compared with traditional structures, enhancing the output voltage. For the piezoelectric transducer (PZT), four piezoelectric cantilever beams are magnetically coupled with the EMG, generating power through bistable motion and broadening the working frequency band of the cantilever beam structure. The harvester is modeled and simulated, and its performance is tested on a simulated vibration platform, with simulation and experimental results in good agreement. Under external excitation at 0.8 Hz, the optimal load and maximum power for each EMG are 8.2 Ω and 207.2 mW, respectively, and the optimal load and maximum power for each PZT are 100 kΩ and 1.52 mW, respectively. The harvester can produce a maximum output power of 420.48 mW, demonstrating high efficiency in energy capture under low-frequency and multidirectional wave excitation.

Design of an ultrafast plasmonic nanolaser for high-intensity broadband emission operating at room temperature

We propose a plasmonic nanolaser based on a metal–insulator–semiconductor–insulator–metal (MISIM) structure, which effectively confines light on a subwavelength scale (∼λ/14). As the pump power increases, the proposed plasmonic nanolaser exhibits broadband output characteristics of 20 nm, and the maximum output power can reach 20 µW. Furthermore, the carrier lifetime at the upper energy level in our proposed structure is measured to be about 400 fs using a double pump-probe excitation. The ultrafast characteristic is attributed to the inherent Purcell effect of plasmonic systems. Our work paves the way toward deep-subwavelength mode confinement and ultrafast femtosecond plasmonic lasers in spaser-based interconnected, eigenmode engineering of plasmonic nanolasers, nano-LEDs, and spontaneous emission control.

Experimental Validation of Power Output and Efficiency for an Oscillating Water Column (OWC)

With the global energy demand escalating and concerns over the environmental impact of fossil fuels, there's a pressing need for cleaner, sustainable alternatives. This study highlights the potential contribution of wave energy to the power needs of coastal structures in the context of renewable energy. The research evaluates the power output and efficiency for an Oscillating Water Column (OWC) system that can be integrated into coastal structures to meet part of their power needs. Findings from both theoretical calculations and a 1:10 scale model experiment are presented. The mechanical power output and efficiency of the system for a full-scale prototype were calculated for deep water conditions with a wave height of 3m. The water surface oscillation inside the chamber is assumed to reflect the oscillation occurring outside the chamber. The maximum average mechanical power output for the full-scale prototype, corresponding to a wavelength of 22.5 m, was determined to be 64.8 kW, achieving a mechanical efficiency of 64.4%. The overall efficiency of the system is calculated as 55% by assuming the generator efficiency to be 85%, resulting in an average power output of approximately 55 kW. A 1:10 scale model of the OWC system with a Wells turbine was constructed and tested in a tank for deep water conditions. Froude similarity and Keulegan-Carpenter similarity were used, ensuring a seamless transition from the model to the prototype. The OWC model was subjected to controlled heaving motion with a period of T=1.2 s. The power generated by the OWC model illuminated four integrated 3.4V LEDs on the Wells turbine, which were used to measure the power output produced. The power output of the model was measured to be a minimum of 0.12 W for a rotational speed of 107 rpm, which corresponds to a power output of 12 kW for the scaled-up prototype. This system has the potential for further enhancement by incorporating multiple OWCs into coastal structures exposed to wave action. Such development could facilitate meeting the power requirements of coastal structures, thereby contributing to the promotion of both renewable energy generation and a sustainable environment. Future research will focus on optimizing OWC chamber sizes for specific sites and refining the model to better capture water surface oscillation dynamics. l

Design and performance evaluation of Front glass-covered photovoltaics-thermal hybrid system for enhanced electrical output and hot water production

Proof of concept is established for the thermal management of PV modules for the simultaneous benefit of electrical and thermal efficiency. It was achieved by designing the controlled open-loop water-based hybrid PV-T system and demonstrated for thermal management of 150W photovoltaic panel at natural solar conditions. In this integrated front glass-covered PV-T hybrid (IFG-PV-T) system, the PV panel is clipped between the front glass and rear aluminium collector without causing any permanent changes in the existing panel. The flow of water from the source tank is controlled by automated solenoid valve assembly coupled with thermocouples. The solenoid operational temperature is fixed at 40°C to controlled the PV surface temperature at an optimum range to mitigate the adverse effect on voltage and current output. The water layer thickness in the front glass box is optimized to filter the maximum infrared radiations and the collector's toughened glass feature allows the maximum light transmittance with super safety. The performance of the IFG-PV-T system has been evaluated in terms of variation in open circuit voltage, short circuit current, maximum power output, electric and thermal efficiency under the natural solar insolation for a week. Experimental investigations revealed that the open-circuit voltage is increased by ∼16.1 % with IFG-PV-T as compared to conventional PV panel. The increment can be attributed to the synergy of the front glass collector and solenoid valve operation at 40oC that regulates PV surface temperature and boost the current output. These factors have ameliorated the electrical efficiency of IFG-PV-T compared to conventional PV panel. The average thermal efficiency was 39.4 ​% wherein the IFG-PV-T system provides ∼100 ​L of hot water (38–41 ​°C) per day. The present controlled loop operation system and collector configuration have proven their significance for electrical power increment and concomitantly able to deliver moderate hot water which can be useful for any household or commercial application.

Multiphonon-coupling yellow laser in Yb:La2CaB10O19 crystal

Yellow lasers at 590 nm have many extensive applications in our daily life, but extremely difficult to attain by traditional solid-state laser technology, owing to the absence of highly-efficient transition channels at this spectral range. In this work, we proposed a cooperative lasing mechanism to obtain the yellow light emission, with multiphonon-assisted electronic transitions and phase-matched frequency-doubling. Based on the predictable configurational coordinate model, we can calculate the multiphonon-assisted emission step-by-step. Using Yb3+-doped La2CaB10O19 crystal as an example, it is capable of producing yellow laser at 581–590 nm, with a maximum output power of 4.83 W and a high slope efficiency of 31.6%. To the best of our knowledge, it represents the highest power of solid-state yellow laser realized in one single crystal pumped by a laser diode. This power scaling can be assigned to the amplified phonon-assisted emission beyond the fluorescence spectrum, and optimized crystal angle for phase-matching condition. Such a compact, low-cost, and high-power laser device, provides an alternative candidate for the spectral “yellow-gap” where no practical solid-state laser exists at present.

Highly efficient nonlinear compression of mJ pulses at 2 µm wavelength to 20 fs in a gas-filled multi-pass cell

Abstract Within this work we demonstrate the highly efficient nonlinear spectral broadening and subsequent temporal compression of 1.49 mJ pulses at 101 kHz repetition rate from an ultrafast thulium-doped fiber laser system employing a gas-filled multi-pass cell. To achieve spectral broadening, we use a krypton and helium-filled Herriott-type multi-pass cell with highly reflective broadband dielectric mirrors. The spectrally broadened pulses are subsequently compressed using fused-silica plates, resulting in a pulse duration of 20 fs and an overall excellent transmission of 96%. Furthermore, the beam quality is preserved up to the maximum output power of 144 W. It provides, to the best of our knowledge, the highest average power with few-cycle pulses at 2 µm wavelength with almost 10 times more pulse energy and 3 times more average power than previous 2-µm multi-pass cells, enabling future secondary source experiments.

The Design and Analysis of a 25-Watt Broad-Band GaN HEMT-Based Power Amplifier

This paper presents the novel design and analysis of a 25 W broadband Class-AB GaN HEMT-based power amplifier working over 0.9–1.7 GHz. A large signal model of the Wolfspeed-make GaN HEMT CG2H40025 has been used in this design. The comprehensive design process has been carried out with the help of the Advanced Design System software by Keysight. Instead of conjugately matching the load and source impedance obtained from load-pull analysis of a nonlinear model of CG2H40025, the value of load and source impedance has been tuned with the help of a novel design approach of an ideal matching design approach. Thus, to achieve an output power of more than 25 W and a flat large signal gain of 15.425 ± 0.375 dB, a novel design approach has been employed to create input and output matching networks, maintaining a lower Q value results in broad bandwidth and for determining the load and source impedances. The circuit has been fabricated on Roger’s substrate RO4350B having a dielectric constant of 3.66 and a loss tangent of 0.0031. The unique design approach based on electromagnetic simulation of the circuit at each design step yielded experimental results that agreed very well with the simulated results. The fabricated power amplifier achieves a power-added efficiency of over 54.78% and a drain efficiency of over 55.45% throughout the entire frequency range. It also delivers a maximum output power of 32.18 W at 1.3 GHz. This power amplifier is developed for L-band Foliage Penetrating Radar.

A self‐adaptive communication‐free control scheme of islanded PV‐storage microgrids

AbstractFor the problem that traditional droop control cannot maintain the maximum output power of photovoltaic (PV) units, this work proposes a self‐adaptive communication‐free control scheme for the islanded PV‐storage AC microgrids. The proposed control enables the maximum power point tracking‐based output active powers of PVs by adaptively adjusting P‐f/Q‐V droop coefficients. It also facilitates adaptive allocations of reactive powers based on the available capacities of PVs and storage modules. The key characteristics of the proposed control strategy are summarized as follows: 1) PV units are controlled as voltage sources, which could participate in the voltage/frequency regulation to a certain extent; 2) maximum power utilization of PVs is obtained; 3) adaptive allocations of reactive powers are realized based on the maximum available capacity of PVs and storage modules. Subsequently, the stability analysis of the proposed self‐adaptive communication‐free control strategy is verified. Finally, the validity of the proposed self‐adaptive communication‐free control method is validated through simulations conducted using MATLAB/Simulink.

Detecting Environmental Conditions in Cultivation Lands Using Bionic Devices

Climate change has an impact on crops, fruits, vegetables, and pest infestation, hence agricultural output is a top priority for most nations. As a result, professional growers have the problem of reaching maximum output results, and greenhouses have emerged as an excellent choice for ensuring these results. Farmers can employ innovative technologies inside greenhouses to prevent insect damage to plants and increase indoor growth through climate management. However, in order to manage agricultural fields and greenhouses successfully, farmers must now use Industry 4.0 technology such as robotics, Internet of Things devices, machine learning software, and so on. In this setting, sensor deployment is critical for gathering data and obtaining knowledge to help farmers make decisions. As a practical option for small farms, this research proposes an autonomous robot that drives along greenhouse crop paths with previously specified routes and can collect environmental data provided by a wireless sensor network when the farmer has no prior knowledge of the crop. An unsupervised learning method is used to cluster the optimal, standard, and deficient sectors of a greenhouse in order to identify improper crop development patterns. Finally, a user interface is built to assist farmers in planning the robot's route and distance while gathering sensor data to monitor crop conditions.

Femtosecond-laser-inscribed cladding waveguides in KTiOPO4 crystal for second-harmonic generation and Y-branch splitters

In this study, the fabrication of straight- and Y-branch-cladding waveguides in KTiOPO4 crystals using femtosecond laser-direct writing is described. The second-harmonic generation (SHG) of green light through the cladding waveguides was realized using a pulsed-wave pump at 1,064 nm. The guiding properties of straight-cladding waveguides fabricated by varying the laser-writing conditions were investigated. The minimum insertion loss was approximately 2.0 dB at 1,064 nm. Confocal micro-Raman spectroscopy was used to investigate the lattice micro-modifications. The maximum SHG conversion efficiency of the straight-cladding waveguide reached 31.4% with a maximum output power of 79.29 mW from an input power of 252.6 mW. The performances of the Y-branch splitters with splitting angles ranging from 0.5° to 2.6° were characterized at 1,064 nm, showing excellent properties, including symmetrical output ends and approximately equal splitting ratios. An SHG conversion efficiency of 13.4% and maximum output power of 33.63 mW were achieved in the Y-branch splitter with a splitting angle of 1.0°. These findings support potential applications in constructing compact-frequency converters by using femtosecond laser-written KTiOPO4 depressed-cladding waveguides.

Evaluation of in-plane architecture in a thermo-electrochemical cell with nanostructured and porous Sb:SnO2 electrodes

Thermo-electrochemical cells (TECs) are able to convert heat into electricity. They are formed by two electrodes (typically Pt) separated by a redox electrolyte (usually 0.4 M aqueous ferro/ferricyanide). The widely adopted architecture of TECs consists of the two electrodes separated by an electrolyte channel. To our knowledge, no studies have been reported exploring a different architecture. Here, we evaluate an alternative configuration, which comprises a substrate with the two electrodes at its ends and with the electrolyte added on the top contacting both electrodes, forming a planar configuration. We explore first the use of the standard Pt electrodes deposited on top of a conductive glass substrate. Then, we replace the Pt by nanostructured and porous Sb-doped SnO2. The planar configurations are compared with their corresponding typical architectures using the common ferro/ferricyanide electrolyte. It was found that the planar TEC with Sb:SnO2 reached a temperature coefficient of 1.76 mV/K, higher than the value obtained in the standard configuration with Sb:SnO2 (1.21 mV/K), and also higher than the planar architecture with Pt electrodes, which showed the typical value for the ferro/ferricyanide electrolyte (1.45 mV/K). As a consequence of this significantly larger value, a 29.7 % higher maximum power output than the planar TEC with Pt was observed. Our study identifies for the first time interesting new features when a planar architecture is employed, opening the door to explore in more detail this alternative configuration in TECs.

I-V response test of 60–150 W mono-crystalline solar panel

This work investigates the discrepancies in electrical parameters of mono-crystalline solar panels between Ago-Iwoye weather conditions and the manufacturer’s specified ideal conditions. Manufacturer’s specifications are typically based on 1,000 W/m2 global solar irradiance, AM 1.5, and 25°C operating temperature, while actual weather conditions at installation sites can vary significantly. Mono-crystalline (single-crystal) silicon solar panels of capacities 60, 80, 100, and 150 W were evaluated through current-voltage (I-V) response tests at an installation site in Ago-Iwoye, Nigeria, with solar irradiance exposure from 11 a.m. to 3 p.m. The analysis of I-V and P-V curves revealed a significant reduction in maximum power output by 28.6%, 25.9%, 28.9%, and 19.36%, respectively, compared to the manufacturer’s stated values. This deviation underscores the importance of considering local weather conditions during solar PV projects, and we recommend adding an additional 20%–30% of the total solar panel capacity during installations to account for variations in solar irradiance and operating temperatures, ensuring optimal performance and effective solar power generation in Ago-Iwoye and similar areas.