Maximum Failure Load Research Articles

Mechanical performance of marine sandwich composites subjected to flatwise compression and flexural loading: Effect of resin pins

Mechanical performance of marine sandwich panels comprising E-glass/vinyl ester face sheets and perforated poly-vinyl chloride foam core was evaluated and compared with conventional foam core sandwich panels. Circular holes through the foam core thickness were drilled with 12 different arrangements in square patterns and the holes were filled with the resin during the infusion process which created the through-the-thickness solid resin pins. The effect of each pattern on the flatwise compression and core shear properties of the sandwich panels were experimentally investigated. The three-point bending maximum failure load of perforated foam core sandwich panels was increased over 133.8% by increasing the diameter of the resin pins at the expense of increased panel weight up to 67%. The flatwise compression stress to induce core crushing was significantly increased by reinforcing the resin pins.

In Vivo Evaluation of Different Collagen Scaffolds in an Achilles Tendon Defect Model.

In the present study, a newly introduced bovine cross-linked collagen scaffold (test material) was investigated in vivo in an Achilles tendon defect model and compared to a commercially available porcine collagen scaffold (control material). In total, 28 male Sprague Dawley rats (about 400 g) were examined. The defined Achilles tendon defect of 5 mm of the right hind limb was replaced by one of the scaffold materials. After euthanasia, the hind limbs were transected for testing. Biomechanical evaluation was carried out via tensile testing (n = 8 each group, observation time: 28 days). Nonoperated tendons from the bilateral side were used as a control (native tendon, n = 4). For the histological evaluation, 12 animals were sacrificed at 14 and 28 days postoperatively (n = 3 each group and time point). Stained slices (Hematoxylin & Eosin) were evaluated qualitatively in terms of presence of cells and cell migration into scaffolds as well as structure and degradation of the scaffold. All transected hind limbs were additionally analyzed using MRI before testing to verify if the tendon repair using a collagen scaffold was still intact after the observation period. The maximum failure loads of both scaffold materials (test material: 54.5 ± 16.4 N, control: 63.1 ± 19.5 N) were in the range of native tendon (76.6 ± 11.6 N, p ≥ 0.07). The stiffness of native tendons was twofold higher (p ≤ 0.01) and the tear strength was approximately fivefold higher (p ≤ 0.01) compared to the repaired tendons with both scaffolds. Histological findings indicated that neither the test nor the control material induced inflammation, but the test material underwent a slower remodeling process. An overall repair failure rate of 48% was observed via MRI. The experimental data of the newly developed test material showed similar outcomes compared to the commercially available control material. The high repair failure rate indicated that MRI is recommended as an auxiliary measurement tool to validate experimental data.

Refill Friction Stir Spot Welding of Dissimilar 6061/7075 Aluminum Alloy

Abstract Refill friction stir spot welding (RFSSW) was used to join 6061-T6 and 7075-T6 aluminum alloys in this work. Different sheet configurations and welding parameters were used to optimize joint strength. The effect of sleeve plunge depth on the microstructure and mechanical properties of the joints were investigated. The results showed that no defects were obtained when 6061-T6 aluminum alloy was placed as the upper sheet. The lap shear failure load of the joint using 6061-T6 aluminum alloy as the upper sheet was higher than that using 7075-T6 as the upper sheet. The maximum failure load of 12,892 N was attained when using the sleeve plunge depth of 3.6 mm. The joint failed at the upward flowing 7075 near the hook.

Variogram-based evaluations of DXA correlate with vertebral strength, but do not enhance the prediction compared to aBMD alone

Ancillary evaluation of spinal Dual-energy X-ray Absorptiometry (DXA) via variogram-based texture evaluation (e.g., Trabecular Bone Score) is used for improving the fracture risk assessment, despite no proven relationship with vertebral strength. The purpose of this study was thus to determine whether classical variogram-based parameters (sill variance and correlation length) evaluated from simulated DXA scans could help predicting the in vitro vertebral strength.Experimental data of thirteen human full vertebrae (i.e., with posterior elements) and twelve vertebral bodies were obtained from two existing studies. Areal bone mineral density (aBMD) was calculated from 2D projection images of the 3D HR-pQCT scan of the specimens mimicking clinical DXA scans. Stochastic predictors, sill variance and correlation length, were calculated from their experimental variogram. Vertebral strength was measured as the maximum failure load of human vertebrae and vertebral bodies from mechanical tests.Vertebral strength correlated significantly with sill variance (r = 0.727) and correlation length (r = 0.727) for the vertebral bodies, and with correlation length (r = 0.593) for full vertebrae. However, the stochastic predictors improved the strength prediction made by aBMD alone by only 11% for the vertebral bodies while no improvement was observed for the full vertebrae.Despite a correlation, classical variogram parameters such as sill variance and correlation length do not enhance the prediction of in vitro vertebral strength beyond aBMD. It remains unclear why some variogram-based evaluations of DXA improve fracture prediction without a proven relationship with vertebral strength.

Bone-Patellar Tendon-Bone Graft Preparation for Fixation with Suspensory Method in Anterior Cruciate Reconstruction: A Biomechanical Study

Background: Many grafts are used for ACL reconstruction with different methods of fixation. We have presented a new technique for BTB (bone-tendon-bone) graft preparation and compared its biomechanical properties with the classic one to see if the suspensory method of fixation is applicable for BTB grafts. Methods: Eight fresh frozen human BTB grafts were prepared. Grafts were randomly divided into two separate groups. Each containing 4 grafts. In the first group grafts were prepared with standard BTB graft method and in the second group grafts were prepared with new enfolded method. All the grafts were assembled in a universal testing machine for testing the mechanical properties of the grafts. Maximum tensile strength, failure load and failure mode were derived from machine and the values were compared in each group. Results: Mean failure load for classic group was 1660.25 and for enfolded group it was 1579.25 (P = 0.25). Mean stiffness for classic group was 285.25 N/meter and for enfolded group it was 268.75 N/ per meter (P = 0.1). In classic group, all failures happened at the bone-ligament junction. In the enfolded group, failures also occurred through the tendino-osseous junction except for one case. Conclusions: Enfolded BTB graft preparation had the same biomechanical indexes of classic method. Therefore this graft preparation method can be used for ACL ligament reconstruction surgery with used of suspensory fixation by Endobutton.

Interface Behavior and Lap Shear Properties of the 7075-T6 Al FSLW Joint Using a Tip-Threaded Pin

For the purpose of reducing the hook and increasing the effective sheet thickness of the friction stir lap welding joint, a tip-threaded pin was used to weld 3 mm-thick 7075-T6 aluminum alloy in this work. Material flow behavior, joint formation mechanism and lap shear properties of the lap joints were mainly discussed. Results showed that when using the tip-threaded pin, lap joint with nearly aequilate stir zone (SZ) along thickness and rather flat hooks were obtained. When using high rotating speeds, the width of the lower SZ exceeded that of the middle SZ. A void, which resulted from the material loss near the lap interface, was observed at the same time. With increasing the rotating speed, the lap shear failure load of the joint initially increased and then decreased, while the fracture mode changed from tensile fracture to shear fracture mode. The maximum failure load of 17661 N was attained for the joint without void at 850 rpm.

Biomechanical study of nickel-titanium three-dimensional memory alloy mesh and autologous bone in treatment of canine tibial plateau collapse fracture

To evaluate the biomechanical effect of a nickel-titanium (Ni-Ti) three-dimensional memory alloy mesh in treating a canine tibial plateau collapse fracture model and to lay a foundation for further experiments in vivo. Sixteen tibial plateau specimens of 8 adult Beagle dogs were harvested. Twelve specimens were taken to prepare canine tibial plateau collapse fracture models (Schatzker type Ⅲ) and randomly divided into groups A, B, and C, with 4 specimens in each group. Four normal tibia specimens were used as blank control group (group D). In groups A and B, the bone defects were repaired with Ni-Ti three-dimensional shape memory alloy mesh combined with autologous bone and simple autologous bone respectively, and fixed with the lateral plate and screw. In group C, the bone defect was directly fixed with the lateral plate and screw. By using a biomechanical tester, a progressive load (0-1 700 N) was loaded vertically above the femoral condyle. The maximum failure load was recorded and the stiffness was calculated according to the load-displacement curve. The maximum failure loads in groups A, B, C, and D were (1 624.72±7.02), (1 506.57±3.37), (1 102.00±1.83), and (1 767.64±24.56) N, respectively; and the stiffnesses were (129.72±20.83), (96.54±27.05), (74.96±17.70), and (169.01±35.62) N/mm, respectively. The maximum failure load and stiffness in group A were significantly higher than those in groups B and C, but which were significantly lower than those in group D ( P<0.05). Ni-Ti three-dimensional memory alloy mesh combined with autologous bone can repair the Schatzker type Ⅲ tibial plateau collapse fracture, which has better biomechanical properties than simple autologous bone grafting.

The effect of femoral bone tunnel configuration on tendon-bone healing in an anterior cruciate ligament reconstruction: An animal study.

ObjectivesTo compare the effect of femoral bone tunnel configuration on tendon-bone healing in an anterior cruciate ligament (ACL) reconstruction animal model.MethodsAnterior cruciate ligament reconstruction using the plantaris tendon as graft material was performed on both knees of 24 rabbits (48 knees) to mimic ACL reconstruction by two different suspensory fixation devices for graft fixation. For the adjustable fixation device model (Socket group; group S), a 5 mm deep socket was created in the lateral femoral condyle (LFC) of the right knee. For the fixed-loop model (Tunnel group; group T), a femoral tunnel penetrating the LFC was created in the left knee. Animals were sacrificed at four and eight weeks after surgery for histological evaluation and biomechanical testing.ResultsHistologically, both groups showed a mixture of direct and indirect healing patterns at four weeks, whereas only indirect healing patterns were observed in both groups at eight weeks. No significant histological differences were seen between the two groups at four and eight weeks in the roof zone (four weeks, S: mean 4.8 sd 1.7, T: mean 4.5 sd 0.5, p = 0.14; eight weeks, S: mean 5.8 sd 0.8, T: mean 4.8 sd 1.8, p = 0.88, Mann-Whitney U test) or side zone (four weeks, S: mean 5.0 sd 1.2, T: mean 4.8 sd 0.4, p = 0.43; eight weeks, S: mean 5.3 sd 0.8,T: mean 5.5 sd 0.8, p = 0.61, Mann-Whitney U test) . Similarly, no significant difference was seen in the maximum failure load between group S and group T at four (15.6 sd 9.0N and 13.1 sd 5.6N) or eight weeks (12.6 sd 3.6N and 17.1 sd 6.4N, respectively).ConclusionRegardless of bone tunnel configuration, tendon-bone healing after ACL reconstruction primarily occurred through indirect healing. No significant histological or mechanical differences were observed between adjustable and fixed-loop femoral cortical suspension methods.Cite this article: Y. Sato, R. Akagi, Y. Akatsu, Y. Matsuura, S. Takahashi, S. Yamaguchi, T. Enomoto, R. Nakagawa, H. Hoshi, T. Sasaki, S. Kimura, Y. Ogawa, A. Sadamasu, S. Ohtori, T. Sasho. The effect of femoral bone tunnel configuration on tendon-bone healing in an anterior cruciate ligament reconstruction: An animal study. Bone Joint Res 2018;7:327–335. DOI: 10.1302/2046-3758.75.BJR-2017-0238.R2.

Bioabsorbable plating in the treatment of pediatric clavicle fractures: A biomechanical and clinical analysis

BackgroundClassic implants for operative intervention of mid-shaft clavicle fractures in adolescents can become symptomatic, requiring removal. This study compares 1) biomechanical properties and 2) clinical outcomes in adolescents of mid-shaft clavicle fracture fixation with bioabsorbable versus metal implants. MethodsSix synthetic clavicles with mid-shaft fractures underwent bioabsorbable plating. A testing frame applied 10 non-destructive torsion and 10 axial compression cycles, followed by cantilever bending to failure. Stiffness was calculated; maximum failure load and failure mode were recorded. Results were compared to previous data for locked metal constructs.Retrospective review of surgically treated clavicle fractures over three years included functional and radiographic outcomes. FindingsBioabsorbable plates had lower torsional stiffness (P < 0.001) and maximum cantilever load (P < 0.0001) than locked metal plates. There was no significant difference in compression stiffness (P = 0.2) or cantilever bending stiffness (P = 0.4). Primary failure of metal plates was screw pull-out compared to plate bending in bioabsorbable constructs.Seven patients with bioabsorbable implants were included. All patients with bioabsorbable constructs achieved radiographic union, but 71% lost reduction. Despite fracture angulation, all achieved normal shoulder function after one year determined by QuickDASH evaluation. None required a second surgery. InterpretationBioabsorbable implants had lower torsional stiffness and cantilever failure load, but comparable compression stiffness to metal implants. Bioabsorbable implants failed via gradual bending versus the catastrophic failure seen in metal implants. The clinical review allows understanding of the sequelae of this lower failure load of bioabsorbable plates where their use allowed in fracture displacement, yet achievement of ultimate radiographic union and acceptable functional outcomes.

Properties and optimization of friction stir spot welded aluminum alloy 3003-H14

Abstract The lightweighting potential in modern manufacturing has been enhanced via the emergence of novel friction stir spot welding approaches by eliminating the conventional joining challenges of aluminum alloys. Optimizing the tool profile of friction stir spot welded joints is thus essential due to the direct controlling influence of tool morphology on material flow, bonding and weld quality. Therefore, this study examines the optimization of friction stir spot welded 1 mm thick 3003-H14 wrought aluminum alloy, by using a cylindrically threaded pin tool morphology and the Taguchi optimization methodology. Tool rotational speed, plunge depth and dwell time are utilized as welding parameters, while maximum shear failure load is employed as the response in this study. Analysis of variance (ANOVA) is employed to systematically investigate the main effect and interaction effect of welding parameters on weld performance. A maximum shear failure load of 2530 N was attained at a parameter combination of 1.50...

Assessment of Conduit-Assisted Primary Nerve Repair Strength With Varying Suture Size, Number, and Location.

Background: Outcomes following digital nerve repair are suboptimal despite much research and various methods of repair. Increased tensile strength of the repair and decreased suture material at the repair site may be 2 methods of improving biologic and biomechanical outcomes, and conduit-assisted repair can aid in achieving both of these goals. Methods: Ninety-nine fresh-frozen digital nerves were equally divided into 11 different groups. Each group uses a different combination of number of sutures at the coaptation site and number of sutures at each end of the nerve-conduit junction, as well as 2 calibers of nylon suture. Nerves were transected, repaired with these various suture configurations using an AxoGuard conduit, and loaded to failure. Results: The 2-way analysis of variance (ANOVA) showed that repairs performed with 8-0 suture have significantly higher maximum failure load compared with 9-0 suture repairs (P < .01). Increasing the number of sutures in the repair significantly increased the maximum failure load in all groups regardless of suture caliber used (P < .01). Repairs with 9-0 suture at the coaptation site did not jeopardize repair strength when compared with 8-0 suture. Conclusions: Conduit-assisted primary digital nerve repairs with 8-0 suture increases the maximum load to failure compared with repairs with 9-0 suture, as does increasing the overall number of sutures. Using 9-0 suture at the coaptation site with 8-0 suture at the nerve-conduit junction does not jeopardize tensile strength when compared with similar repairs using all 8-0 suture and may decrease inflammation at the repair site while still achieving sufficient tensile strength.

Biomechanical study of olecranon plate fixation in comminuted osteoporotic fracture model: locking compression plates versus dynamic compression plates

This cadaveric biomechanical study compared locking compression plates (LCP) to dynamic compression plates (DCP) in a comminuted olecranon fracture using cyclic loading to measure fragment displacement and maximal failure load. Eight paired human cadavers were used. We confirmed all specimens were osteopenic using DEXA. One paired half of the specimens randomly received LCP fixation and the other DCP. Implants were secured to the intact ulna prior to creating an osteotomy. Two vertical osteotomies were created to simulate a fracture gap of 5 mm. The specimens were loaded and placed on the MTS machine. Saw-toothed cyclic loading was applied and force/gap displacement measured. Failure was defined as fracture gap greater than 2 mm or catastrophic failure of the bone/construct. Biomechanical parameters were compared between two groups. The average force for the DCP was 22.12 N compared to 33.40 N (P&lt;0.05) for the LCP. The average gap for the DCP was 7.32 mm compared to 6.40 mm (P&lt;0.05) for the LCP. The force measure was statistically significant at 60, 70, 80, 90, and 100 mm of displacement (P&lt;0.05) for the LCP. This implies that the LCP was able to withstand higher force than the DCP. The gap displacement was statistically significant at 60, 70, 80, 90, and 100 mm of displacement (P&lt;0.05). This implies that the LCP maintained the reduction better than the DCP. No differences in force/gap were noted when comparing gender, right versus left forearm, or osteoporotic versus osteopenic bone. There was no difference when failure occurred between the DCP and LCP groups. Our study found that LCP was able to withstand higher force than DCP, and there was less displacement of the fracture with biomechanical testing in the LCP compared to the DCP. Both could be appropriate surgical techniques for fixation of comminuted olecranon fractures. When treating comminuted and osteopenic fractures, LCP are advantageous. Further studies would be needed to compare these two plates clinically.

Research on the Anti-Cracking Performance of High Viscoelastic Tar Sands

The principle of fracture energy was put forward to evaluate the anti-cracking performance of high viscoelastic tar sands. To effectively reconstruct the anti-cracking performance of high viscoelastic tar sands, a semi-circular bending test was performed to measure the maximum load and fracture energy. The test results show that when the test temperature remains constant, the maximum failure load of the specimen increases along with loading rate, while the fracture energy of the specimen decreases along with increasing loading rate. Meanwhile, when the loading rate remains constant, the maximum failure load of the specimen decreases along with increasing temperature, while the fracture energy increases along with temperature. The test device is simple and cheap, while the test specimen is easy to manufacture. Therefore, the semi-circular bending test can be used as a standard method for testing the crack resistance design of asphalt mixture. A parameter sensitivity analysis is also conducted by using the ABAQUS finite element numerical simulation method. The experiment and numerical simulation results are compared to verify whether fracture energy can be used to evaluate the anti-cracking performance of high viscoelastic tar sands.

Novel technique for repairing posterior medial meniscus root tears using porcine knees and biomechanical study.

Transtibial pullout suture (TPS) repair of posterior medial meniscus root (PMMR) tears was shown to achieve good clinical outcomes. The purpose of this study was to compare biomechanically, a novel technique designed to repair PMMR tears using tendon graft (TG) and conventional TPS repair. Twelve porcine tibiae (n = 6 each) TG group: flexor digitorum profundus tendon was passed through an incision in the root area, created 5 mm postero-medially along the edge of the attachment area. TPS group: a modified Mason-Allen suture was created using no. 2 FiberWire. The tendon grafts and sutures were threaded through the bone tunnel and then fixed to the anterolateral cortex of the tibia. The two groups underwent cyclic loading followed by a load-to-failure test. Displacements of the constructs after 100, 500, and 1000 loading cycles, and the maximum load, stiffness, and elongation at failure were recorded. The TG technique had significantly lower elongation and higher stiffness compared with the TPS. The maximum load of the TG group was significantly lower than that of the TPS group. Failure modes for all specimens were caused by the suture or graft cutting through the meniscus. Lesser elongation and higher stiffness of the constructs in TG technique over those in the standard TPS technique might be beneficial for postoperative biological healing between the meniscus and tibial plateau. However, a slower rehabilitation program might be necessary due to its relatively lower maximum failure load.

Orthotopic Transplantation of Achilles Tendon Allograft in Rats

The biology and function of orthotopic transplantation of Achilles tendon allograft are unknown. Particularly, the revitalization of Achilles allograft is a clinical concern. Achilles allografts were harvested from donor rats and stored at −80 °C. Subcutaneous adipose tissue was harvested from the would-be allograft recipient rats for isolation of mesenchymal stem cells (MSCs). MSCs were cultured with growth differentiation factor-5 (GDF-5) and applied onto Achilles allografts on the day of transplantation. After the native Achilles tendon was resected from the left hind limb of the rats, Achilles allograft, with or without autologous MSCs, was implanted and sutured with calf muscles proximally and calcaneus distally. Animal gait was recorded presurgery and postsurgery weekly. The animals were sacrificed at week 4, and the transplanted Achilles allografts were collected for biomechanical testing and histology. The operated limbs had altered gait. By week 4, the paw print intensity, stance time, and duty cycle (percentage of the stance phase in a step cycle) of the reconstructed limbs were mostly recovered to the baselines recorded before surgery. Maximum load of failure was not different between Achilles allografts, with or without MSCs, and the native tendons. The Achilles allograft supplemented with MSCs had higher cellularity than the Achilles allograft without MSCs. Deposition of fine collagen (type III) fibers was active in Achilles allograft, with or without MSCs, but it was more evenly distributed in the allografts that were incubated with MSCs. In conclusion, orthotopically transplanted Achilles allograft healed with host tissues, regained strength, and largely restored Achilles function in 4 wk in rats. It is therefore a viable option for the reconstruction of a large Achilles tendon defect. Supplementation of MSCs improved repopulation of Achilles allograft, but large animal models, with long-term follow up and cell tracking, may be required to fully appreciate the functional benefits of MSCs.

The Strength of Transosseous Medial Meniscal Root Repair Using a Simple Suture Technique Is Dependent on Suture Material and Position

Background: A simple suture technique in transosseous meniscal root repair can provide equivalent resistance to cyclic load and is less technically demanding to perform compared with more complex suture configurations, yet maximum yield loads are lower. Various suture materials have been investigated for repair, but it is currently not clear which material is optimal in terms of repair strength. Meniscal root anatomy is also complex; consisting of the ligamentous mid-substance (root ligament), the transition zone between the meniscal body and root ligament; the relationship between suture location and maximum failure load has not been investigated in a simulated surgical repair. Hypotheses: (A) Using a knottable, 2-mm-wide, ultra-high-molecular-weight polyethylene (UHMWPE) braided tape for transosseous meniscal root repair with a simple suture technique will give rise to a higher maximum failure load than a repair made using No. 2 UHMWPE standard suture material for simple suture repair. (B) Suture position is an important factor in determining the maximum failure load. Study Design: Controlled laboratory study. Methods: In part A, the posterior root attachment of the medial meniscus was divided in 19 porcine knees. The tibias were potted, and repair of the medial meniscus posterior root was performed. A suture-passing device was used to place 2 simple sutures into the posterior root of the medial meniscus during a repair procedure that closely replicated single-tunnel, transosseous surgical repair commonly used in clinical practice. Ten tibias were randomized to repair with No. 2 suture (Suture group) and 9 tibias to repair with 2-mm-wide knottable braided tape (Tape group). The repair strength was assessed by maximum failure load measured by use of a materials testing machine. Micro–computed tomography (CT) scans were obtained to assess suture positions within the meniscus. The wide range of maximum failure load appeared related to suture position. In part B, 10 additional porcine knees were prepared. Five knees were randomized to the Suture group and 5 to the Tape group. All repairs were standardized for location, and the repair was placed in the body of the meniscus. A custom image registration routine was created to coregister all 29 menisci, which allowed the distribution of maximum failure load versus repair location to be visualized with a heat map. Results: In part A, higher maximum failure load was found for the Tape group (mean, 86.7 N; 95% CI, 63.9-109.6 N) compared with the Suture group (mean, 57.2 N; 95% CI, 30.5-83.9 N). The 3D micro-CT analysis of suture position showed that the mean maximum failure load for repairs placed in the meniscus body (mean, 104 N; 95% CI, 81.2-128.0 N) was higher than for those placed in the root ligament (mean, 35.1 N; 95% CI, 15.7-54.5 N). In part B, the mean maximum failure load was significantly greater for the Tape group, 298.5 N (P = .016, Mann-Whitney U; 95% CI, 183.9-413.1 N), compared with that for the Suture group, 146.8 N (95% CI, 82.4-211.6 N). Visualization with the heat map revealed that small variations in repair location on the meniscus were associated with large differences in maximum failure load; moving the repair entry point by 3 mm could reduce the failure load by 50%. Conclusion: The use of 2-mm braided tape provided higher maximum failure load than the use of a No. 2 suture. The position of the repair in the meniscus was also a highly significant factor in the properties of the constructs. Clinical Relevance: The results provide insight into material and location for optimal repair strength.

Friction Stir Lap Welding Ti–6Al–4V Alloy Using a Threaded Pin by Simulation and Experimental Investigation

Commonly, the rotating tool during friction stir welding of Ti–6Al–4V alloy owns flat surfaces since serious tool wear always appears during welding. However, a tool with flat surface easily results into insufficient material mixing during friction stir lap welding process. In order to increase material mixing between the upper and lower sheets while welding Ti–6Al–4V alloy, a tool with a threaded pin was used in this work. The material flow behaviors at the lap interfaces using pins with and without threads were investigated. Results showed that when using the threaded pin, the maximum material flow velocity showed an obvious increase at the lap interface, which was beneficial to enhance the material mixing between upper and lower sheets. Even using the threaded pin, void-like defects appeared at joint bottoms using higher rotating speeds of 200 and 180 rpm, which were eliminated by decreasing the rotating speed to 150 rpm because of reduced temperature gradient along sheet thickness direction. The welding processes in this work were considered as below β-transus temperature because no obvious lamellar structures were observed on all the joints. The maximum failure load of 20.23 KN was attained when using 200 rpm. The lap joints presented tensile fracture mode.

Embedded Connector in Severe Optimization of Steel Plate for Shear Strengthening of RC Beam: Experimental and Numerical Investigations

Environmental impact has become one of the major factors taken into consideration for recent civil engineering studies and projects. Thus, researchers have been concentrating on shear strengthening of existing reinforced concrete structure as an upgrade method instead of demolishing and reconstructing. In general, shear strengthening of RC beams using externally bonded steel plate has gained huge popularity. However, premature debonding of plates is the main drawback of the system, which could be mitigated using embedded connector; thus, the dimension of steel plate could be reduced significantly. Furthermore, numerical analysis on shear strengthening of beams using embedded connector would provide a great insight on the structural behavior. The aim of this research is to severely reduce the dimension of the steel plate using embedded connector for shear strengthening of RC beams and to investigate the performances of optimized shear‐strengthened beams through experimental and numerical investigations. The results showed that the dimension of plate was reduced without debonding of the plate if the beam was designed for shear strengthening with the consideration of yield strength of steel plate and shear link. Experimental results showed a maximum increase in failure of 24%. The numerical results predicted accurately the structural performance of beams. The embedded connector had a great effect in deferring and minimizing the debonding failure and accordingly increasing the maximum load of shear failure between 14.5% and 24% compared to control beam.

Effect of replacing the main reinforcement by steel fibers on flexural behavior of one-way concrete slabs

The main objective of the research is to study the preparation of one way slabs of ordinary concrete, and then to prepare concrete slabs by replacing the main reinforcing steel with two kinds of steel fibers (ordinary steel fibers and recycled steel fibers) by fraction volumes of 0.125, 0.250, and 0.375%. Also, study the mechanical properties of the mixtures as a ompressive strength, indirect tensile strength, and flexural strength. Concrete slabs of these mixtures have been prepared with specific geometrical dimensions700 * 300 * 70 mm, exposed to line load, to study the bending moment and maximum failure load of these slabs. A concrete mixture was produced after proportionment based on the ACI and casting six cubes tested at the ages of 7 and 28 days where the strength requirements for design were achieved. The main mixtures of research were produced, three cubes for compressive strength testing, twenty one cylinders for indirect tensile strength testing, and twenty one prisms for modulus of rupture testing. Also sixteen concrete slabs were prepared, two of them were reference slabs without reinforcing steel, the other two with main reinforcing steel only, six of them replaced by the main reinforcing steel with ordinary steel fibers, and the last six replacing the main reinforcing steel with recycled steel fibers. The results showed that both the failure load and the resultant deflection in concrete slabs decreased by (20.09%, 51.91%) for maximum load and by (35.18%, 81.48%) compared to the reference slabs when replacing the main reinforcing steel with steel fiber, also by (25.72%, 38.29%) to failure load and (38.88%, 79.63%) for the deflection compared to the reference slabs when replacing the main reinforcing steel with recycled steel fibers. The best value for maximum load and deflection could be obtained from this study was at 0.125% replacement ratio of the main reinforcing steel with recycled steel fibers, the highest value of ductility was 3.77 at the replacement ratio of 0.250% of the main reinforcing steel with the ordinary steel fibers, also the highest hardness value was 11.67 kN / mm with the replacement ratio of 0.125% of the main reinforcing steel with recycled steel fibers and increased by 61.85% than the hardness of the reference slabs.

Novel ultrasound assisted suture anchor system using the BoneWelding® technology yields a comparable primary stability in osteopenic and healthy human humeri as a benchmark anchor

IntroductionThe aim of this biomechanical study was to evaluate the primary stability of the SportWelding® Sombrero 3.6 mm suture anchor system in osteopenic and healthy cadaveric humeri. MethodsThe Sombrero® and BioCorkscrew® anchors were deployed in 8 osteopenic and 4 healthy cadaver humeri after the bone mineral density (BMD) measurements of the 32 specimens. Both anchors were loaded with a USP Nr. 2 FiberWire® suture. An established cyclic testing protocol was performed. The maximum failure load (Fmax), the system displacement and the modes of failure were recorded. ResultsThe Fmax and system displacement of the Sombrero® in osteopenic and healthy humeri was equivalent to the Bio-Corkscrew® benchmark anchor; there were no significant differences in the maximum failure loads and system displacement values. Only anchor and suture dislocations were observed; suture ruptures did not occur. ConclusionThis study shows that the Sombrero® yields similar maximum failure loads and system displacement values as the established Bio-Corkscrew® benchmark anchor. The primary stability of the Sombrero® and Bio-Corkscrew® seems to be independent of the bone mineral quality. This relatively small-sized polymer anchor is independent of the BMD and may be an alternative to established suture anchors in rotator cuff repair.