Maximum Difference Research Articles

CFD Investigation on Combined Ventilation System for Multilayer-Caged-Laying Hen Houses.

Mechanical ventilation is an important means of environmental control in multitier laying hen cages. The mainstream ventilation mode currently in use, negative-pressure ventilation (NPV), has the drawbacks of a large temperature difference before and after adjustment and uneven air velocity distribution. To solve these problems, this study designed and analyzed a combined positive and negative-pressure ventilation system for laying hen cages. According to the principle of the conservation of mass to increase the inlet flow in the negative-pressure ventilation system on the basis of the addition of the pressure-wind body-built positive-and-negative-pressure-combined ventilation (PNCV) system, further, computational fluid dynamics (CFD) simulation was performed to analyze the distribution of environmental parameters in the chicken cage zone (CZ) with inlet angles of positive-pressure fans set at 45°, 90°, and 30°. Simulation results showed that the PNCV system increased the average air velocity in the CZ from 0.94 m/s to 1.04 m/s, 1.28 m/s, and 0.99 m/s by actively blowing air into the cage. The maximum temperature difference in the CZ with the PNCV system was 2.91 °C, 1.80 °C, and 3.78 °C, which were all lower than 4.46 °C, the maximum temperature difference in the CZ with the NPV system. Moreover, the relative humidity remained below 80% for the PNCV system and between 80% and 85% for the NPV system. Compared with the NPV system, the PNCV system increased the vertical airflow movement, causing significant cooling and dehumidifying effects. Hence, the proposed system provides an effective new ventilation mode for achieving efficient and accurate environmental control in laying hen cages.

Time wears on everyone, but not equally quickly

In 30 patients (average age 38 ± 8 years, 77% male, 23% female) with intra-oral scans made at intake and after 3 years, tooth wear progression was measured. With the aid of GeoMagic to superimpose the scans, the maximum difference in height of 64 surfaces was measured per surface. A large variation was found in progression rates between patients, between various teeth in a single mouth, and between surfaces on a single tooth. Tooth wear progression rates are therefore highly individual and can even be very localized. Treatment must therefore be individualized, with an essential role for measuring tooth wear when deciding on the need for restorative treatment.

Comparison of sEMG activity of submental muscles between the head-lift exercise, tongue-press exercise and the head extension tongue-press exercise in healthy young adults.

Swallowing is a complex function that requires precise coordination between different muscles. Weakness in submental muscles can lead to complications such as pharyngeal residue and aspiration. Therefore, exercise interventions targeting these muscles, such as the Head-Lift Exercise (HLE), are clinically important but pose challenges. This study aimed to compare the myoelectric activity of submental muscles during traditional Head-Lift Exercise (HLE), Tongue-Press Exercise (TPE) and Head Extension Tongue-Press Exercise (HETPE), providing potential alternatives to HLE. Thirty healthy volunteers (22 females and 8 males, mean age 25.63 ± 5.27 years) participated in this cross-sectional study. Surface electromyography (sEMG) recorded activity of the submental muscles bilaterally during HLE, TPE and HETPE. Participants performed each manoeuvre for 14 s, repeated three times in a counterbalanced order. Statistical analyses assessed differences in mean, maximum and median frequency of the sEMG signals among manoeuvres using repeated-measures analysis of variance (RM-ANOVA). The experienced irritation levels by participants during manoeuvres were also compared by the Friedman test. HETPE exhibited significantly higher maximum sEMG activity compared to HLE and TPE (p < .05). Mean sEMG activity was significantly increased during HETPE compared to TPE. Median frequency was significantly lower during HETPE compared to the two other exercises, indicating greater muscle fatigue. Participants reported similar levels of irritation for HLE and HETPE, and significantly lower levels during TPE. These results indicate that HETPE is effective in activating and strengthening submental muscles, potentially serving as a viable alternative to HLE without added difficulty. Further research is recommended to assess the long-term impacts on swallowing physiology in patients with dysphagia.

Optimum delineation of skin structure for dose calculation with the linear Boltzmann transport equation algorithm in radiotherapy treatment planning.

This study investigated the effectiveness of placing skin-ring structures to enhance the precision of skin dose calculations in patients who had undergone head and neck volumetric modulated arc therapy using the Acuros XB algorithm. The skin-ring structures in question were positioned 2mm below the skin surface (skin A) and 1mm above and below the skin surface (skin B) within the treatment-planning system. These structures were then tested on both acrylic cylindrical and anthropomorphic phantoms and compared with the Gafchromic EBT3 film (EBT3). The results revealed that the maximum dose differences between skins A and B for the cylindrical and anthropomorphic phantoms were approximately 12% and 2%, respectively. In patients 1 and 2, the dose differences between skins A and B were 9.2% and 8.2%, respectively. Ultimately, demonstrated that the skin-dose calculation accuracy of skin B was within 2% and did not impact the deep organs.

Numerical and experimental study on the aerodynamic noise characteristics of 600-km/h high-speed maglev trains

Abstract High-speed maglev trains represent a new mode of transportation; however, their 600-km/h traveling speed causes serious aerodynamic noise problems, with very little research on the aerodynamic noise of such trains. To clarify the aerodynamic noise source and radiation characteristics of high-speed maglev trains, both large eddy simulations and wind tunnel experiments with a 1:8 scale three-train model were conducted to obtain the aerodynamic noise source spectrum and spatial distribution characteristics of the maglev train at different speeds; the contribution of the dipole noise source was also analyzed. The results revealed that the train shape has a significant impact on the frequency distribution of the far-field aerodynamic noise below 1 kHz, with the highest sound power concentrated on the train head, especially in the areas around the track joint and streamlined sections. The surface dipole sound source energy increases linearly with speed and is mainly distributed at the bottom of the train head and tail train body. A short-streamlined train exhibited the highest ratio, especially in the trailing edge area, up to 1.42×1011 dB. The far-field sound pressure level of the short-streamlined maglev train is significantly higher, with a maximum difference of about 10 dB(A). The distribution pattern of far-field sound pressure level is influenced by the train type, reflected in the tail train and wake area. Different frequency intervals have different relationships between the acoustic pressure level and frequency; long-streamlined models may enhance broadband features in the sound field distribution of high-speed maglev trains. These findings could be used to guide the aero-acoustic design of maglev trains with a designed speed of 600 km/h.

Fire Resistance Performance of Constrained H-Shaped Steel Columns with Uneven Vertical Temperature Distributions

Steel columns, which are widely used in building frameworks and spatial structures, are susceptible to capacity degradation during fires, potentially leading to the overall collapse of buildings. Existing research on the fire resistance of steel columns assumes that the temperature loads encountered by steel columns are evenly distributed vertically. However, real-world fire scenarios often feature significant vertical temperature differences. Therefore, this study comprehensively investigated these variations to derive a temperature curve that accurately represents real fire conditions. Subsequently, the fire resistance limits of steel columns were studied using this temperature curve, leading to a revised calculation formula for the critical fire resistance temperatures of steel columns. The following conclusions were drawn: (1) Nonuniform longitudinal temperature distributions are influenced by parameters such as the fire source distance, the heights of ventilation openings, and the distance between a vent and the temperature measurement point. Among them, the fire source distance has the greatest impact, with the maximum longitudinal temperature difference reaching over 500 °C. (2) Variations in the load ratio and longitudinal temperature differences alter the failure positions of steel columns, reducing their critical temperatures by up to 200 °C. (3) The revised critical fire resistance temperature formula is more accurate and safer compared with that outlined in the “Technical Code for Fire Protection of Steel Structures” (GB51249-2017). These findings offer valuable insights for the fire designs of steel columns.

ANALISIS HUJAN MAKSIMUM PADA DAERAH ALIRAN SUNGAI BABAK KABUPATEN LOMBOK BARAT

Hydrological analysis is the most important measurement in determining runoff in order to find ways to overcome flooding. The flow rate that is the basis for calculating flood control and protection is the planned flood flow rate obtained from the sum of the volume of rain runoff and the flow rate of the water catchment area in question during a certain return period. This research is a case study using rainfall data for 10 years, namely 2014-2023. Rainfall prediction is an estimate of the amount of rain that will fall in a river basin. There are several methods for determining annual rainfall, the Gumbel distribution method, Pearson log type III, and the normal method. After analyzing the annual rainfall data obtained at the West Lombok Regency Meteorology, Climatology and Geophysics Agency office, using three methods, namely the EJ Gumbel method, the Log Person Type III method and the Normal method, where from the three methods the maximum rainfall difference was quite large, In the following table you can see the difference in the amount of maximum rainfall in the return period T years.

The novel stereoscopic cooling plate designs and performance analysis for battery thermal management systems

This study explores the design and performance of liquid cooling plate-based battery thermal management system for lithium-ion battery packs through numerical simulation. We first assess traditional straight-channel cooling plates with three different placement strategies. The conventional design with bottom-mounted cooling plates demonstrates the most effective thermal management at the same total coolant mass flow rate. This suggests that the influence of reducing coolant flow velocity on the cooling performance outweighs the influence of increasing the heat exchange area under our simulated conditions. Advanced stereoscopic cooling plate structures, referred to as 3DCP-A and 3DCP-B, are then introduced, significantly enhancing battery thermal management performance. To achieve a maximum temperature difference ≤ 5.0 K for the most discharge process, the required mass flow rate of the 3DCP-B decreases by 30.0 g∙s−1 and 10.0 g∙s−1 compared to the conventional bottom-mounted cooling plate and 3DCP-A, respectively, and the pressure drop reduces by 75.9 % and 44.3 %, respectively. The power consumption for the 3DCP-B design is only 6.0 % of that for the traditional design. Finally, the effects of key operating temperatures on the cooling performance of the optimal 3DCP-B design are discussed. The insights obtained in this study provide valuable guidance for developing more efficient and effective pack-level liquid cooling plate-based battery thermal management system, essential for improving the reliability and performance of electric vehicles.

Performance Evaluation of a Novel Cold Plate with Double-Layer Interdigitated Flow Channels for Battery Thermal Management

Working temperature is a non-negligible factor that determines the operating performance of lithium-ion batteries which are extensively used in vehicles and the energy storage industry. Therefore, it is essential to maintain the battery temperature within an acceptable range while minimizing power consumption and ensuring uniform temperature distribution. To achieve these goals, a novel cold plate design with double-layer interdigitated flow channels is proposed in this study for efficient prismatic battery thermal management. The newly proposed cold plate design outperforms the serpentine-channel based cold plate under the same working conditions, resulting in significant improvements in both battery temperature and pressure drop. Specifically, the maximum temperature and temperature difference were reduced by over 10%, while the power cost was reduced by approximately 50%. By considering different arrangements of inlet and outlet locations, 32 non-repeating designs of the cold plate flow paths were examined. Relatively good inlet and outlet layouts are determined by comparing battery thermal management metrics including the maximum temperature, temperature difference, uniform index, and pressure drop, as well as the overall performance factors that consider both the battery temperature and power cost. In addition, the effects of the inlet flow velocity are examined to determine the optimal design.

A steady-state distributed parameter ultrathin heat pipe model considering the unsaturated wick

Ultrathin heat pipes have become mainstream to address the heat dissipation issues of small electronic devices. Numerous numerical studies based on the saturated wick assumption have been proposed to analyze their heat transfer performance. In order to achieve a more accurate assessment, this study presents a three-dimensional model that quantitatively reflects the relationship between capillary pressure and medium volume, along with a corresponding correlation. Based on this, a steady-state distributed parameter ultrathin heat pipe model considering the retreating of medium volume in the wick and the unsaturation vapor-liquid interface was developed, whose accuracy was verified by the experimental data. The results demonstrated that the capillary pressure increased with the decrease of medium volume and contact angle. The evolution of the overall meniscus with medium volume was categorized into two stages, where capillary pressure dependent on the main and micro meniscus at different stage. The medium volume distribution, corresponding to capillary pressure, will automatically adjust to match the overall medium pressure drop. Comparative analysis against experimental data, the proposed model reduced the maximum temperature difference error by 8.43 % compared to the saturated wick assumption at a heat load of 6 W, revealing that the unsaturated liquid wick model exhibited higher accuracy.

Refining Alnico 8 magnets with composition optimization of matrix phase, directional solidification and magnetic field annealing

Optimized shape anisotropy of the Fe-Co rich ferromagnetic (α1) phase and the effective separation of the α1 and α2 phases with maximum magnetization difference—where α2 represents a paramagnetic magnetic phase—are the key parameters for maximizing the magnetic properties of Alnico magnets. In this manuscript, efforts have been undertaken to optimize the shape anisotropy of the α1 phase and increase the difference in magnetization and separation between α1 and α2 phases by fine tuning Al and Ni contents, directional solidification and magnetic field annealing methods. At first, Alnico magnets were fabricated by adjusting the content of α2 phase followed by homogenization, magnetic field annealing at high temperature, and low-temperature tempering. Intrinsic coercivity (Hcj) of ⁓146.0 kA/m, remanence (Br) of ⁓0.90 T and maximum energy density ((BH)max) of 46.02 kJ/m3 are achieved in the magnet with 8.2 wt% Al and 12.8 wt% Ni treated in field of 1.5 T for 10 minutes. At the second stage, the magnet with optimal magnetic properties is directionally solidified to develop columnar grains, and then the α1 phase is grown in the direction of the columnar grains by magnetic field annealing to enhance the (BH)max to 79.8 kJ/m3. The axial ratio of the α1 phase increased significantly with the increase of the grain size, particularly in the directionally solidified magnets. The Curie temperature of the α1 phase is noted near 1150 K, while the Curie temperature of the α2 phase is below 400 K. The magnets demonstrated excellent temperature stability, with magnetic properties decreasing by only 10–12 % at 800 K. These results may pave the way for further development of Alnico magnets specifically for high temperature applications.

The Faustini Permanently Shadowed Region on the Moon

Faustini crater (41 km diameter) hosts a large (664 km2) permanently shadowed region (PSR) with a high potential to harbor water-ice deposits. One of the 13 candidate Artemis III landing areas contains a portion of the crater rim and proximal ejecta. The ShadowCam instrument aboard the Korea Pathfinder Lunar Orbiter provides detailed images of the PSR within Faustini. We characterize the terrain and thermal environment within the Faustini PSR from ShadowCam images, Lunar Reconnaissance Orbiter thermal measurements and laser ranging, and thermal modeling. Our mapping revealed three distinct areas of the floor of Faustini based on elevations, slopes, and surface roughness. These units broadly correlate with temperatures; thus, they may be influenced by variations in volatile sublimation. Crater retention and topographic diffusion rates appear to be asymmetric across the floor, likely due to differences in maximum and average temperatures. Several irregular depressions and a pronounced lobate-rim crater are consistent with subsurface ice. However, differences in the thicknesses of deposited materials on the floor may also explain the asymmetry. Additionally, zones of elevated surface roughness across Faustini appear to result from overprinted crater ray segments, possibly from Tycho and Jackson craters. Mass wasting deposits and pitting on opposite sides of the crater wall may have resulted from the low-angle delivery of material ejected by the Shackleton crater impact event, suggesting that the Artemis III candidate landing region named “Faustini Rim A” will contain material from Shackleton.

Investigation and quantification of composition variability in urinary stone analysis.

To investigate the variability in urinary stone composition analysis due to sampling and suggest potential solutions. We collected 1,135 stone fragments from 149 instances that had undergone a stone removal at Hanoi Medical University Hospital from January 2022 to August 2022. Each fragment was ground into fine powder and divided into separate specimens if the amount was abundant. For composition analyzing every specimen, Fourier transform infrared spectroscopy was performed. The composition of a given fragment was the average of its belonging specimens. The variability in composition was assessed on the fragment level (i.e., between fragments of an instance). We defined an instance as "significantly variable" if the maximum difference in any composition across its belonging fragments was equal to or greater than a given threshold. On average, there were 7.6±3.3 stone fragments per instance and 2.3±0.5 specimens per fragment. We found that the variability could be substantial on the fragment level. Eighty-nine (69.5%) and 70 (54.7%) out of 128 multiple-component instances were significantly variable if the threshold was set at 20% and 30%, respectively. The variability of an instance on the fragment level was correlated with the size of fragment and the number of components. Our study demonstrated the significant variability in urinary stone composition and showed that it correlated with the size and the impurity of samples. Mapping denotation while sampling and analyzing as well as reporting the composition of individual fragments could be valuable to reduce potential variability.

Discrete Homogeneous and Non-Homogeneous Markov Chains Enhance Predictive Modelling for Dairy Cow Diseases.

Modelling and predicting dairy cow diseases empowers farmers with valuable information for herd health management, thereby decreasing costs and increasing profits. For this purpose, predictive models were developed based on machine learning algorithms. However, machine-learning based approaches require the development of a specific model for each disease, and their consistency is limited by low farm data availability. To overcome this lack of complete and accurate data, we developed a predictive model based on discrete Homogeneous and Non-homogeneous Markov chains. After aggregating data into categories, we developed a method for defining the adequate number of Markov chain states. Subsequently, we selected the best prediction model through Chebyshev distance minimization. For 14 of 19 diseases, less than 15% maximum differences were measured between the last month of actual and predicted disease data. This model can be easily implemented in low-tech dairy farms to project costs with antibiotics and other treatments. Furthermore, the model's adaptability allows it to be extended to other disease types or conditions with minimal adjustments. Therefore, including this predictive model for dairy cow diseases in decision support systems may enhance herd health management and streamline the design of evidence-based farming strategies.

Simulation of ambient temperature and humidity distribution in eight-span greenhouse under different wind conditions and corn height

The greenhouse environment suitable for crop growth usually depends on reasonable ventilation, and outdoor air flow state and indoor crop height are important factors affecting the ventilation effect. This study conducted simulation and experimental research on corn cultivation in an eight-span plastic greenhouse, analyzing the effects of outdoor wind speed, wind direction, and indoor crop height variations on the uniformity of temperature and relative humidity distribution as well as the air flow dynamics within the greenhouse. The study shows that as outdoor wind speed increases from 0.5 m/s to 2.5 m/s, for every 1 m/s increment, temperatures decrease by 2.2 °C and 0.9 °C, respectively. The increase in outdoor wind speed resulted in uniformity of greenhouse temperature and humidity along the vertical height, but exacerbated the degree of inhomogeneity in the east-west direction. The change in outdoor wind direction leads to differences in airflow direction and ventilation volume. On the south side of the greenhouse, while temperature is lower, the relative humidity is higher, with maximum differences in temperature and humidity between the north and south sides being 0.6 °C and 1.5 %, respectively, when the northeast wind blows. The east wind has the best cooling effect. The uneven degree of temperature and humidity distribution in the east and west direction of the greenhouse is positively correlated with crop height. This study can provide valuable insights for adjusting and optimizing natural ventilation strategies in large multi-span greenhouses.

Flexible and anisotropically conductive film by assembly of silicone rubber and cobalt-coated glass fiber composites

In this study, we prepared electromagnetic cobalt-coated glass fiber (Co@GF) composites via an electroless plating method. Subsequently, a conductive sandwich flexible film consisting of Co@GF composites and liquid silicone rubber (RTV-2) was successfully formed using the tape casting method at room temperature. Based on the perfect coating and excellent electrical conductivity of the Co@GF composites, the resultant RTV-2/Co@GF/RTV-2 sandwich flexible film showed a low volume resistivity of 0.264 Ω·cm and could stretch to 100% (of 4.40 Ω·cm) without obvious fracture. When a magnetic field was applied during the curing process, the electromagnetic Co@GF composites were aligned automatically in the RTV-2 matrix because of their ferromagnetic nature. The as-prepared film exhibited anisotropy in its electrical performance. The volume resistivity parallel to the magnetic field direction is approximately two times lower than that in the perpendicular direction. The maximum difference in the volume resistivity (ρ∥ = 0.768 Ω·cm and ρ⊥ = 1.549 Ω·cm) was obtained at a magnetic field intensity of 800 mT. In addition, a magnetic field intensity of 100 mT helps improve the electrical conductivity of the as-obtained sandwich film. The anisotropic RTV-2/Co@GF/RTV-2 sandwich flexible film is considered a promising flexible electronic sensor, where discrepant inductive sensitivity is required in orthogonal directions.

Consumer Perception of Sweeteners in Yogurt

Consumers are interested in products with reduced sugar, a trend which has been attributed to consumers associating high-sugar foods with obesity, diabetes, heart disease and high blood pressure. The objective of this study was to evaluate consumer perception of sugar reduction in yogurt - both conceptually and for liking of actual products. An online survey (n = 1290) was conducted to evaluate consumer perception of sweeteners available in commercial yogurts. Participants who purchased yogurt at least once in the past 3 mo completed a series of exercises that involved demographics, agreement, Kano, and Maximum Difference (MaxDiff) scaling questions. Subsequently, vanilla 1% milkfat yogurts sweetened with sucrose were formulated to iso-sweet taste intensity with either stevia, allulose, a blend of sucrose and honey or a blend of sucrose, stevia and allulose using magnitude estimate scaling followed by paired comparison tests with consumers (n = 40). A consumer acceptance test (n = 229) was then conducted using the 5 vanilla yogurts. Half of the consumers (n = 115) were primed with the specific yogurt sweetener and the other half were not. Survey and acceptance test data were evaluated by univariate and multivariate analyses. Conceptually, consumers preferred the claim "naturally sweetened" over a reduced sugar claim in yogurt (P < 0.05). Honey was preferred over other sweeteners, followed by agave nectar and cane sugar (P < 0.05). Allulose was the least preferred sweetener option conceptually (P < 0.05). Priming with sweetener type positively impacted consumer acceptance, regardless of sweetener (P < 0.05). When yogurts were tasted, yogurts sweetened with sucrose were the most preferred regardless of priming (P < 0.05). Yogurts sweetened with allulose or a blend of allulose, stevia, and sucrose received higher liking scores than yogurts with stevia (P < 0.05), suggesting that allulose can assist with sugar reduction in yogurt. Consumers are interested in healthy yogurts that are naturally sweetened, but flavor/taste remains the driving force for liking and purchase. The use of a natural non-nutritive sweetener that delivers the sensory experience of sucrose is ultimately more important than familiarity with the actual sweetener.

Investigating the impact of battery arrangements on thermal management performance of lithium-ion battery pack design

The working temperature is one of the key factors affecting the efficiency and safety performance of automotive power batteries. Current battery pack design primarily focuses on single layout configurations, overlooking the potential impact of mixed arrangements on thermal management performance. This study presents a module-based optimization methodology for comprehensive concept design of Lithium-ion (Li-ion) battery pack. Firstly, the arrangement modules is optimized and performed using particle swarm optimization algorithms considering various arrangement layout (i.e. rectangular, diamond, and staggered arrangements) by taking the intercell spacing and maximum temperature of the modules as design objectives. Secondly, the battery pack configuration design is performed employing a neural network model reflect diverse battery module configurations within the pack, exploring their impact on thermal management performance. The hybrid battery arrangement effectively improves thermal management, and the module spacing helps to enhance heat dissipation. The staggered arrangement has a greater impact on the heat dissipation performance of the battery pack, but the spacing between different modules varies with the position of the modules. When all configuration schemes are staggered modules, the optimal range of the spacing between modules is between 6 and 7 mm. However, the study observes a non-linear relationship between module spacing and the maximum temperature difference within the battery pack. While increasing module spacing initially decreases temperature differences, it eventually reverses, suggesting that spacing alone may not consistently enhance thermal management. Validation with a lithium-ion battery pack case study demonstrates the method’s effectiveness, providing valuable knowledge for future cell and pack designs that employ different battery cell arrangements and diverse cooling strategies.

A new method for scaling inlet flow waveform in hemodynamic analysis of aortic dissection.

Computational fluid dynamics (CFD) simulations have shown great potentials in cardiovascular disease diagnosis and postoperative assessment. Patient-specific and well-tuned boundary conditions are key to obtaining accurate and reliable hemodynamic results. However, CFD simulations are usually performed under non-patient-specific flow conditions due to the absence of in vivo flow and pressure measurements. This study proposes a new method to overcome this challenge by tuning inlet boundary conditions using data extracted from electrocardiogram (ECG). Five patient-specific geometric models of type B aortic dissection were reconstructed from computed tomography (CT) images. Other available data included stoke volume (SV), ECG, and 4D-flow magnetic resonance imaging (MRI). ECG waveforms were processed to extract patient-specific systole to diastole ratio (SDR). Inlet boundary conditions were defined based on a generic aortic flow waveform tuned using (1) SV only, and (2) with ECG and SV (ECG + SV). 4D-flow MRI derived inlet boundary conditions were also used in patient-specific simulations to provide the gold standard for comparison and validation. Simulations using inlet flow waveform tuned with ECG + SV not only successfully reproduced flow distributions in the descending aorta but also provided accurate prediction of time-averaged wall shear stress (TAWSS) in the primary entry tear (PET) and abdominal regions, as well as maximum pressure difference, ∆Pmax, from the aortic root to the distal false lumen. Compared with simulations with inlet waveform tuned with SV alone, using ECG + SV in the tuning method significantly reduced the error in false lumen ejection fraction at the PET (from 149.1% to 6.2%), reduced errors in TAWSS at the PET (from 54.1% to 5.7%) and in the abdominal region (from 61.3% to 11.1%), and improved ∆Pmax prediction (from 283.1% to 18.8%) However, neither of these inlet waveforms could be used for accurate prediction of TAWSS in the ascending aorta. This study demonstrates the importance of SDR in tailoring inlet flow waveforms for patient-specific hemodynamic simulations. A well-tuned flow waveform is essential for ensuring that the simulation results are patient-specific, thereby enhancing the confidence and fidelity of computational tools in future clinical applications.

Thermodynamics-based unsaturated hydro-mechanical-chemical coupling model for wellbore stability analysis in chemically active gas formations

A thermodynamics-based unsaturated hydro-mechanical-chemical (HMC) coupling model is developed to analyze the coupled response and stability of boreholes in chemically active gas formations. The newly coupled constitutive relations are formulated by incorporating the chemical effect into the solid-gas-liquid unsaturated framework to account for the interactions between rock deformation, gas-liquid two-phase flow, and chemical potential difference. Compared with previous models, the present model shows significant prediction differences in field variables and wellbore stability evolution. The maximum absolute difference of pore pressure, effective radial stress, effective tangential stress, and collapse pressure can reach 8.98 MPa, 7.64 MPa, 7.29 MPa, 7.65 MPa, respectively. It is more conservative to select a long-term wellbore collapse pressure rather than a short-term one to guide drilling operations. The two-phase flow behavior, jointly controlled by wellbore pressure, capillary pressure, and chemical osmosis effect, provides a more realistic observation of the mud intrusion process. Compared with low salinity muds, high salinity muds can effectively impede the mud intrusion into the formation, which is more conducive to preventing wellbore collapse, but at the same time increases the risk of wellbore fracture. Sensitivity analysis shows that solute diffusion and reflection coefficients affect early wellbore stability through pore pressure and solute transport, while the chemical swelling coefficient has a long-term effect through chemically induced deformation. The results can provide theoretical guidance for quantitative optimization of mud parameters and prevention of wellbore instability when drilling in chemically active gas formations.