Maximum Adsorption Capacity Research Articles

5-Fluorouracil adsorption on graphene oxide-amine modified graphene oxide/hydroxyapatite composite for drug delivery applications: Optimization and release kinetics studies

The present study focused on investigation of graphene oxide/hydroxyapatite (GO/HAp) and amine modified graphene oxide/hydroxyapatite (GO-NH2/HAp) composites as potential drug carrier agents for 5-Fluorouracil (5-FU). Incorporation of 5-Fluorouracil drug was performed via adsorption through π-π interactions and electrostatic attractions. Modification of graphene oxide was performed for the production of amine modified graphene oxide/hydroxyapatite composite with the intention of enhancing adsorption performance. The X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA) and zeta potential/particle size analysis were performed for particle characterization while Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) analysis were used to analyze detailed morphological properties. Experimental design studies were followed out in order to determine the effect of adsorption parameters including graphene oxide amount, pH and initial drug concentration on 5-Fluorouracil adsorption behavior. Adsorption isotherms of both composites with unmodified and modified GO were best fitted to Freundlich model with R2 values of 0.9616 and 0.9682 respectively. The maximum adsorption capacities (qm) were calculated as 47.3 mg/g and 18.4 for graphene oxide/hydroxyapatite and amine modified graphene oxide/hydroxyapatite composites respectively at pH 2.0. The highest adsorption percentage was obtained for amine modified graphene oxide/hydroxyapatite composite as 40.87 % at pH 2.0 condition. In vitro release kinetic studies revealed that compliance with Higuchi and Korsmeyer-Peppas kinetic models were observed for graphene oxide/hydroxyapatite, whereas zero order and Korsmeyer-Peppas kinetic models pointed out as the well-fitted model for amine modified graphene oxide/hydroxyapatite composite. The release period of 5-FU drug from all composites were continued up to 8–10 h in physiological conditions (pH 7.4, 37 °C) indicating an achieved controlled release. Based on the overall findings, graphene oxide/hydroxyapatite and amine modified graphene oxide/hydroxyapatite composites could be suggested as a potential drug delivery agent for 5-FU in clinical applications.

Comparison of the natural and surfactant-modified zeolites in the adsorption efficiency of sunset yellow food dye from aqueous solutions

The removal of Sunset Yellow (E110) on natural zeolite and zeolite modified with the cationic surfactant cetyl pyridinium chloride (CPC) was studied using the adsorption method. The structural characteristics of the surfactant-modified zeolite (SMZ-CPC) were investigated using X-ray diffraction(XRD), Fourier transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET) analysis, and the scanning electron microscopy (SEM) images. The effect of different parameters on the adsorption process, such as equilibration time and amount of adsorbent at 298 K, were determined using UV–Vis spectroscopy. The maximum dye removal percentage on SMZ-CPC was obtained with 0.08 g of adsorbent in 30 min. The results show that the zeolite modified with CPC surfactant (SMZ) has a higher adsorption capacity for Sunset Yellow than the unmodified zeolite (natural form). The experimental adsorption data were nonlinearly analyzed using isotherm equations such as Langmuir, Freundlich, Temkin, Langmuir-Freundlich (or Sips), and Extended Langmuir (EL). The experimental data were better fitted with the Sips isotherm. The adsorption kinetic data were analyzed using eight models in nonlinear forms: the pseudo-first-order (PFO), pseudo-second-order (PSO), integrated kinetic Langmuir (IKL), Elovich, intraparticle diffusion (IPD), mixed order rate equation (MOE), fractal-like pseudo-first-order (FL-PFO) and fractal-like pseudo-second-order (FL-PSO). According to the results of the coefficient of determination (R2), Elovich kinetic model well expressed E110 adsorption onto SMZ-CPC. Most of the dye removal takes place in less than 5 min and the maximum adsorption capacity is 5.06 mg/g. The results of this study show that zeolite modified with cationic surfactant is an effective adsorbent for removal anionic dyes from an aqueous solution.

The solid-solution HxPO4@Fe3O4 synthesized by irradiation enhances the adsorption capacity of tungsten(VI) and anti-interference of coexisting oxoanion in waste water: Surface oxolation interaction

Tungsten (W), mainly existing as hexavalent oxidation state in nature, has been considered as an increasingly prominent waterborne pollutant, but it is also a critical metal. Therefore, it is important to develop a material to adsorb W(VI) from the waste water containing W(VI) to realize the high-efficiency enrichment and recovery of W(VI). Inspired by self-assembly of phosphate and W(VI) ions in the acidic solutions to form phosphotungstic polyoxoanions (e.g., Keggin-type PW12O403−), in this work, we have loaded the phosphate ion to surface of the magnetic Fe3O4 nanoparticles (Fe3O4 NPs) by β particle irradiation to synthesize a composite adsorbent, HxPO4@Fe3O4 solid-solution (SS). This novel adsorbent is very efficient for W(VI) adsorption and recovery. The results of a batch of adsorption experiments indicate that HxPO4@Fe3O4 SS has a high adsorption efficiency for W(VI) in aqueous environments and strong anti-interference of coexist ions especially PO43−. Under room temperature conditions (∼25 °C), the maximum adsorption capacity reaches 88.44 mg g−1. This method not only ensures a substantial increase in W(VI) adsorption but also provides a facile means for adsorbent recovery, while minimizing additional environmental burdens. Based on the characterization results from Fourier transform infrared, Zeta potential, and X-ray photoelectron spectroscopies, we speculated that the possible mechanism of the adsorption process is that formed W(VI) polyoxoanions in acidic solutions are initially attracted by electrostatic attraction to the positively charged HxPO4@Fe3O4 surface, and then oxolation reaction occurs between W-OH of polyoxoanions and phosphate hydroxyl (P-OH) on the HxPO4@Fe3O4 surface to form P-O-W bridging oxygen group. This adsorption mechanism is also reflected in the adsorption kinetics, following a pseudo-second-order kinetic model, and adsorption thermodynamics, exhibiting a large enthalpy change (−76.3 kJ/mol) and a significant entropy reduction (−174.5 J/(mol K)).

Enhanced removal of tetracycline by vitamin C-modified cow manure biochar in water

Vitamin C (VC), due to its chemical properties, can provide more oxygen-containing functional groups such as hydroxyl groups for biochar (BC), which promotes the adsorption of tetracycline on biochar. Therefore, in this study, cow dung biochar (CDBC) was modified with VC and VC-modified CDBC (CDBC-VC) was synthesized. The modified biochar was characterized and related factors, adsorption kinetics, isotherms and adsorption mechanisms were investigated. Adsorption kinetics indicate a fast rate of adsorption. The adsorption isotherms showed that the maximum adsorption capacity was 31.72 mg/g (CDBC) and 50.90 mg/g (CDBC-VC), respectively, and the adsorption process was inhomogeneous with multiple molecular layers and the adsorbent has a higher affinity. Mechanistic studies showed that hydrogen bonding interactions, π-π electron donor-acceptor interactions, hydrophobic interactions, and electrostatic interactions were the key to the adsorption process. The analysis of adsorbent regeneration showed that CDBC-VC had good adsorption performance. CDBC and CDBC-VC showed the best performance in simulated industrial wastewater with removal rates of 78.81% and 93.69%. The adsorption mechanism was comprehensively analyzed using six machine learning models. The extreme gradient boosting model gave the best fit. Analysis of the weights of the input variables for predicting adsorption efficiency showed that the ratio of initial TC concentration to BC dosage (29.8%), specific surface area (23%), isoelectric point (8.8%), and ash content (7.7%) had a significant effect on the predicted results.

Combining SiO2 NPs with biochar: a novel composite for enhanced cadmium removal from wastewater and alleviation of soil cadmium stress.

Cadmium (Cd) pollution in water and soil seriously threatens human health. Biochar and nanomaterials have high potential for solving the cadmium pollution problem due to their abundant pores and high specific surface area. Here, the preparation of the composite material SiO2NPs@BC (SBC) using SiO2 NPs (SN) and silkworm excrement biochar (BC) is described, along with its application in the remediation of cadmium-contaminated water and soil. Characterization experiments (SEM&EDS, BET, FTIR, XRD, and XPS) demonstrated that SiO2NPs@BC has a high specific surface area (46.5767m2/g), a well-developed pore structure (0.608375cm3/g), and abundant surface functional groups (Si-C, Si-O, Si-O-Si), providing active sites for the adsorption of Cd. Batch adsorption experiments in water showed that the adsorption capacity of SBC is higher than that of biochar (BC) and SN, with a maximum Langmuir adsorption capacity of 141.99mg/g. After five adsorption cycles, the removal rate of SBC was 73.04%, significantly higher than the 64.97% obtained for BC. The application of SBC not only improved the soil physicochemical properties by increasing the soil pH, the cation exchange capacity, and the soil organic matter content but also by reducing the amount of DTPA-Cd (24.6%) and the plant bioconcentration factor (28.28%) in the soil, converting Cd into more stable fractions (Red-Cd, Ox-Cd). Based on the results, SBC can effectively reduce Cd pollution.

Removal of trace Na and K metal ions by resin-grafted crown ether for electronic-grade N-methyl pyrrolidone purification

The semiconductor industry’s rapid evolution necessitates ultra-high-purity N-methyl pyrrolidone (NMP) as an essential electronic-grade solvent. The development of an efficient coordination material to reduce trace metal ions, particularly Na and K metal ions, to below 1 ppb in NMP solution is a significant challenge. To address this, a novel coordination material, St-DVB-g-ACE, has been developed for the removal of Na and K metal ions from NMP. The material was synthesized by grafting 4′-aminobenzo-15-crown-5-ether onto a strong acid gel resin. The resulting St-DVB-g-ACE-3 exhibited excellent coordination performance for Na and K metal ions, with maximum Langmuir adsorption capacities reaching 20,000 μg/g and 33,333 μg/g, respectively. Of particular interest was the ability of St-DVB-g-ACE-3 to reduce all trace metal ions in industrial-grade NMP to below 1 ppb within a fixed bed column, achieving the stringent requirements for electronic-grade NMP at the G3 level. Additionally, the absorbent enhances the purity of NMP from 99.82 % to 99.84 %, indicating that the material is not dissolved and can exist stably in NMP. Its excellent recyclability and reproducibility make it highly practical for industrial use. Density functional theory (DFT) simulation, complemented by spectral analyses, revealed the interaction force and thermodynamic properties between Na and K metal ions and crown ether ring, and illustrated the interaction between anionic sulfonic group (−SO3−) and metal ions. The prepared resin-grafted crown ether adsorbents are highly effective in the thorough removal of trace metal ions from NMP solution, offering a novel and effective method for the production of electronic-grade NMP.

Enhanced phosphate removal from aqueous environments using three-dimensional La-doped carboxylic carbon nanotubes/alginate: Performance and mechanisms

The excessive amounts of phosphorus (P) discharged and usage have caused eutrophication and algal blooms, which seriously jeopardize the environment even the human health. In this study, carbon nanotubes (CNTs) served as carriers to develop a lanthanum-based sodium alginate hydrogel (La-CNT-COOH/SA) aimed at efficiently removing phosphate from wastewater. Characterization results confirmed successful deposition of La(OH)3 nanoparticles onto CNT-COOH. The optimal adsorption efficiency of La-CNT-COOH/SA hydrogels occurred at pH 4, with a maximum adsorption capacity of 54.4 mg/g under an initial phosphate concentration of 60 mg/L. Batch experiments demonstrated that La-CNT-COOH/SA performed well across a favorable pH range and exhibited high tolerance to common coexisting ions during phosphate adsorption. Adsorption isotherms indicated a dominance of both physical and chemical mechanisms in phosphate removal by La-CNT-COOH/SA. At elevated phosphate concentrations, the adsorption process followed quasi-second-order kinetics, primarily driven by chemical adsorption. Multi-instrument characterization emphasized that the substantial loading of La(OH)3 on CNT-COOH significantly contributed to adsorption, alongside crosslinked lanthanum ions on sodium alginate and abundant hydroxyl groups. Mechanisms of adsorption by La-CNT-COOH/SA encompassed electrostatic interactions, surface precipitation, and in-sphere complexation (La-O-P). These findings on fabrication, properties, and adsorption mechanisms of the phosphate-removal hydrogel lay a theoretical foundation for applying biomass-based materials in large-scale remediation practices.

Preparation and evaluation of polymeric ionic liquid functionalized microparticles as the efficient adsorbent for pipette tip solid phase extraction of sulfonamides

Sulfonamides (SAs) residues are commonly found in environmental samples, which is highly concerning for public safety and environmental protection. The detection of SAs is quite important but challenging. In this work, a kind of polymeric ionic liquid functionalized microparticles (PIL-FM) was synthesized via a simple free radical polymerization reaction, and applied as the adsorbent for pipette tip solid phase extraction (PT-SPE) of three SAs from river water, milk powder and honey samples. The adsorption performance of PIL-FM on SAs were evaluated using adsorption kinetics and adsorption isotherms, and the results showed that PIL-FM had the best selectivity for SMZ with the maximum adsorption capacity was as high as 45.05 mg·g−1. The extraction process was optimized and the adsorption mechanism was preliminarily discussed. PIL-FM has the excellent selectivity for SAs mainly because of the strong π-π interaction, and the electrostatic repulsion between them in the elution step also has a positive impact. Under optimal conditions, combined with HPLC, this PT-SPE method had wide linearity (0.2–100 μg·L−1, R2 ≥ 0.9998) and low limits of detection (0.06–0.08 μg·L−1). The intra-day and inter-day repeatability were found to be 3.7 %–4.6 % and 4.5 %–6.2 %, respectively. The suggested PT-SPE method is simple, low cost, rapid, and efficient to extract SAs, and can be applied for the monitoring of SAs residues in the aquatic environment and in food.

Biosorbent treatment of fluorene using activated carbon derived from the pyrolysis process of date pit wastes

Activated carbon (AC) derived from Date pits (DP) wastes was used as an eco-friendly and effective biosorbent for the removal of fluorene (FLU) from organic wastes. The maximum capacity of DP was 6.71 mg g−1, compatible with the Freundlich model. FLU adsorption's chemisorption performance on DP was involved in following a superior linear fit for the pseudo-2nd-kinetic model. The maximum adsorption capacity from the pseudo-2nd order kinetic model fitted with the experimental findings and found to be 3.73 g, 2.62, 1.13, 0.955, 0.749, 0.591, and 0.665 mg g−1 at 25, 3, 35, 4, 45, 5 and 55 °C, respectively. The negative value of the spontaneous nature of the adsorption corresponds to the exothermic nature however, + ΔS corresponds to an increase in the degree of freedom for FLU adsorption. The relatively high value of activation energy (Ea) demonstrates that the adsorption of FLU onto DP is classified as chemical adsorption, and found to be 84.8 kJ mol−1. Also, the result of XRD shows that the prepared DP was re-used four times without substantially decreasing performance. In addition, it appears that AC prepared from DP is a promising adsorbent with a low cost for removing many organic pollutants.

Porosity of green body: A potential essential factor regulating the making of sintered ceramsite from aluminum-based drinking water treatment residuals

Ceramsite is commonly applied in filtration systems for water treatment and aluminum (Al)-based drinking water treatment residue (DWTR) has been widely reported to have high potential to be recycled as main ingredient to make the sintered ceramsite. Various key factors affecting ceramsite making (e.g., composition and sintering temperature) have been identified to promote the beneficial recycling; however, according to sintering processes, this study hypothesized that porosity of green body was also a potential key factor, and then moisture content of green body (33 %-40 %) and particle size of DWTR (< 425 μm), which were the parameters initially considered for ceramsite making, were adopted to regulate the porosity for affecting characteristics and mechanisms investigation. The results verified the hypothesis and showed that increasing moisture content tended to decrease loss on ignition, apparent density, and bulk density, to increase water absorption, and to cause rougher surface of ceramsites, promoting the maximum Cu adsorption capacity of the ceramsite (estimated by Langmuir model); while at medium level of moisture content (e.g., 35 %), a relatively high compressive strength, strong Cu adsorbability (evaluated by Freundlich model), and low solubility in hydrochloric acid were found. Moreover, larger sized DWTR tended to increase loss on ignition, broken rate, solubility in hydrochloric acid, silt content, and water absorption, to reduce apparent density and compressive strength, and to cause rougher surface of the ceramsite, promoting the maximum adsorption capacity and decreasing the adsorbability of Cu. Further analysis suggested that moisture content was mainly through regulating total volume of voids and amount of raw materials to affect sintering, while particle size was mainly through regulating the contacting of particles. These results demonstrated the importance of the moisture contents of green body and the particle size of DWTR on affecting sintered ceramsite making, and porosity of green body was recommended to be taken as an essential factor when determining the optimal condition to make sintered ceramsite making.

Selective extraction of Quercetin from rose petal extracts using poly (acrylamide-co-ethylene glycol dimethylacrylate) based magnetic molecularly imprinted polymer

Under ultrasound irradiation, a highly selective Magnetic Molecularly Imprinted Polymer (MMIP) was synthesized by polymerizing monomers on magnetite. The Density Functional Theory was utilized for the selection of suitable monomers based on binding energy interaction between quercetin and monomers (Acrylamide, Acrylonitrile, Methacrylic Acid). Quercetin served as the template molecule, while acrylamide was used as the functional monomer, and a mixture of DMSO and water was employed as the porogen solvent. This study aims to synthesize and evaluate the effectiveness of MMIP and analyze its adsorption isotherm and kinetics. It was observed that the Freundlich model supports the adsorption of quercetin on MMIP, and the kinetic data correlates better with the Pseudo-first-order kinetic model. The MMIP exhibited a pronounced selectivity in the adsorption of quercetin with a maximum adsorption capacity of 10.07 mg g-1 in 30 min. Furthermore, the physiochemical properties of synthesized sorbent were undergone for characterization using FESEM, EDX, XRD, FTIR, VSM, and TGA. Finally, real-time determination of quercetin was carried out using rose petal extract, integrating MMIP adsorption followed by HPLC detection. The results suggest that MMIP is a promising material for the real-time determination of quercetin from rose petal extract.

Development of morphine analgesia using biocompatible synthesized molecular imprinted hydrogel based on tragacanth gum

AbstractA novel molecular imprinted hydrogel using tragacanth gum (MITMIH) was synthesized for extending morphine analgesic efficacy by controlled release. The characterized MITMIH was used as a new morphine carrier that can increase analgesic time window after its single injection in mice. During in vitro optimization, the MITMIH showed maximum adsorption capacity (~113 mg g−1) at pH = 6.5 after 20 min immersion (400 μM initial morphine concentration, 10 mg MITMIH). During in vivo test, we examined the analgesic effect in mice by dissolving morphine in physiologic saline or by loading on MITMIH. The results of a single injection revealed that morphine‐loaded MITMIH shifted the time profile of morphine analgesia from 123.4 to 257.6 min. This indicates almost 100% efficacy in the controlled release of the drug during 5 h after the injection. Furthermore, cytotoxicity and mitochondrial membrane potential test was evaluated against normal rat kidney epithelial (NRK) and Rat Dermal Fibroblasts (RDF). The results confirmed that the MITMIH could be considered as a potential carrier increasing length of morphine analgesia after the first single injection without any cytotoxicity and negative effect on cell tissues. This may in turn reduce repeated use of the drug to achieve satisfactory analgesia in patients with chronic pain.

Construction of an amphiphilic ionic gel based on quaternised carboxymethyl konjac glucomannan: Preparation and its salt-ion-resistant properties in methylene blue adsorption

Construction of amphiphilic ionic hydrogels: hydrogels were formed by free radical copolymerization of quaternized carboxymethyl konjac glucomannan as the backbone and acrylamide acrylate as the functional monomer, labeled as QCAAM. The structure of the hydrogel was characterized and verified. The adsorption behavior of QCAAM hydrogels on methylene blue (MB) was systematically investigated. The results showed that 99.07 % removal and 1109.21 mg/g adsorption capacity were achieved at optimum pH (pH=10). In addition, QCAAM4 showed enhanced adsorption of methylene blue under the interference of Na+, K+, and Ca2+. Its adsorption capacity increased with the concentration of interfering ions, with the maximum adsorption capacity of 1076.85 mg/g. The adsorption behaviors of the hydrogel conformed to the Langmuir isothermal and pseudo-second-order kinetic models. Thermodynamic studies showed that the adsorption was endothermic and spontaneous.

Ternary‐Grafted Starch‐Based Hydrogel with Improved Adsorption Capacity for Dyes

AbstractBiomass‐based hydrogels can be used as the adsorbents in sewage water, as they have good adsorption capacity for heavy ions and dyes. A ternary‐grafted starch‐based hydrogel, St1.0/CMC0.5/P(AM3.0‐AA5.0‐AMPS1.0), was prepared using cornstarch (St) and sodium carboxymethyl cellulose (CMC) as raw materials, with acrylamide (AM), acrylic acid (AA), and 2‐acrylamido‐2‐methylpropane sulfonic acid (AMPS) as graft monomers. Due to the introduction of CMC and AMPS, the number and type of effective adsorption functional groups in the St1.0/CMC0.5/P(AM3.0‐AA5.0‐AMPS1.0) hydrogel increased, leading to an improved adsorption capacity and removal rate for methylene blue (MB). The maximum adsorption capacity and removal rate for MB could be 1624.49 mg/g and 91.8 %, respectively, at 25 °C. According to the adsorption isotherm and adsorption kinetics, the MB adsorption process on the hydrogel occurs according to the Langmuir isotherm model and quasi‐second‐order kinetics via a chemisorption process occurring on the adsorbent monolayer. Moreover, the St1.0/CMC0.5/P(AM3.0‐AA5.0‐AMPS1.0) hydrogel displayed good regeneration performance. The removal rate for MB could still achieve 84.3 % after the hydrogel was reused four times.

Orange Peels as Activated Carbon Charcoal For Cu (II) Ions Elimination From Water Sources

Objectives: The goal of this work is to create inexpensive Orange Peel Activated Carbon (OPAC) for the environmentally friendly to eliminate of Cu (II) from its aqueous solution. Methods: activated carbon made by calcining orange peels at 500°C to cause them to burn. Methods: The samples were characterized using FTIR, transmission electron microscopy, and nitrogen adsorption-desorption. Cu (II) was adsorbed in a batch procedure utilizing 0.25 g of (OPAC) and 100 mL of solution with varying beginning concentrations ranging from 20–80 mg/L. The investigation focused on the effects of variables pH, temperatures, concentrations, dosages, and times on the adsorption capacity. Thermodynamic parameters were computed, adsorption kinetics were assessed using pseudo-first and pseudo-second-order were computed models, and the adsorption isotherms were fitted using the Langmuir and Freundlich models. Findings: The stretching of the hydroxyl groups is shown by peaks at 3100 and 4000 cm-1 as well as the 3300–3800 cm-1 region in the FTIR. Findings: the functionalized (OPAC). N2 adsorption isotherm revealed a hysteresis loop in the p/p0 region between 0.2 and 1. The surface area of obtained mesoporous OPAC was 0.99 nm. The maximum adsorption capacity (79.056 mg/g). Removal of Cu (II) was 99%. The adsorption process was spontaneous and less random, as indicated by the negative values of thermodynamic parameters (∆S° -14.0, ∆H°-54.76, and ∆G°-60.36 kJ.mol-1). According to the findings, orange peel has a high surface area and is highly porous, which allows it to effectively remove over 99% of harmful heavy metals from water sources. Novelty: The study proves that orange peel can be effectively used as one of the best-quality, reasonably priced, readily available, eco-friendly bio-sorbents that is also beneficial to the economy in the long run. Keywords: Orange peel, Cu (II), Adsorption, Kinetic, Thermodynamic, IFTR

Enhanced Tetracycline Adsorption Using KOH-Modified Biochar Derived from Waste Activated Sludge in Aqueous Solutions

Antibiotic pollution poses a serious environmental concern worldwide, posing risks to ecosystems and human well-being. Transforming waste activated sludge into adsorbents for antibiotic removal aligns with the concept of utilizing waste to treat waste. However, the adsorption efficiency of these adsorbents is currently limited. This study identified KOH modification as the most effective method for enhancing tetracycline (TC) adsorption by sludge biochar through a comparative analysis of acid, alkali, and oxidant modifications. The adsorption characteristics of TC upon unmodified sludge biochar (BC) as well as KOH-modified sludge biochar (BC-KOH) were investigated in terms of equilibrium, kinetics, and thermodynamics. BC-KOH exhibited higher porosity, greater specific surface area, and increased abundance of oxygen-based functional groups compared to BC. The TC adsorption on BC-KOH conformed the Elovich and Langmuir models, with a maximum adsorption capacity of 243.3 mg/g at 298 K. The adsorption mechanisms included ion exchange, hydrogen bonding, pore filling, and electrostatic adsorption, as well as π-π interactions. Interference with TC adsorption on BC-KOH was observed with HCO3−, PO43−, Ca2+, and Mg2+, whereas Cl−, NO3−, and SO42− ions exhibited minimal impact on the adsorption process. Following three cycles of utilization, there was a slight 5.94% reduction in the equilibrium adsorption capacity, yet the adsorption capacity remained 4.5 times greater than that of unmodified sludge BC, underscoring its significant potential for practical applications. This research provided new insights to the production and application of sludge biochar for treating antibiotic-contaminated wastewater.

Efficient water purification: CuO-enhanced biochar from banana peels for removing Congo red dye.

Treating dye-containing wastewater poses numerous challenges due to its high chemical complexity and its persistent nature. Thus, the present study aims to synthesize biochar derived from banana peel (BC) and its nanocomposites with copper oxide nanoparticles (CuOx/BC1-x) for the purpose of adsorptive removing Congo red (CR) dye from water. Several analytical methods were utilized to describe the physicochemical features of the CuOx/BC1-x nanocomposites. It was found that the crystallinity of the nanocomposites gradually improved, while the specific surface area and the surface electronegativity were reduced with increasing x value. The effects of x values (0-0.5), interaction time (10-120 min), adsorbent dose (0.01-0.05 g), initial CR concentration (20-200 mg/L), and the solution temperature (20-60 °C) were evaluated on CR removal. The obtained results revealed that the CuO0.5/BC0.5 nanocomposite showed the highest adsorption efficiency with a maximum adsorption capacity of 233.6 mgg-1. Analysis of the equilibrium experimental data revealed that the Langmuir and the pseudo-2nd-order models were the most proper to describe the current adsorption process. Moreover, the thermodynamics studies demonstrated that the adsorption process was spontaneous, endothermic, and random.

Experimental and Theoretical Studies on the Adsorption of Bromocresol Green from Aqueous Solution Using Cucumber Straw Biochar

Biochar prepared from crop straw is an economical method for adsorbing bromocresol green (BCG) from textile industrial wastewater. However, there is limited research on the adsorption mechanism of biochar for the removal of BCG. This study utilized cucumber straw as raw material to prepare biochar with good adsorption potential and characterized its physicochemical properties. Through adsorption experiments, the effects of solution pH, biochar dosage, and initial dye concentration on adsorption performance were examined. The adsorption mechanism of cucumber straw biochar (CBC) for BCG was elucidated at the molecular level using adsorption kinetics, adsorption isotherm models, and density functional theory (DFT) calculations. Results show that the specific surface area of the CBC is 101.58 m2/g, and it has a high degree of carbonization, similar to the structure of graphite crystals. The presence of aromatic rings, –OH groups, and –COOH groups in CBC provides abundant adsorption sites for BCG. The adsorption process of CBC for BCG is influenced by both physical and chemical adsorption, and can be described by the Langmuir isotherm model, indicating a monolayer adsorption process. The theoretical maximum monolayer adsorption capacity (qm) of BCG at 298 K was calculated to be 99.18 mg/g. DFT calculations reveal interactions between BCG and CBC involving electrostatic interactions, van der Waals forces, halogen–π interactions, π–π interactions, and hydrogen bonds. Additionally, the interaction of hydrogen bonds between BCG and the –COOH group of biochar is stronger than that between BCG and the –OH group. These findings provide valuable insights into the preparation and application of efficient organic dye adsorbents.

A comprehensive investigation of the adsorption behaviour and mechanism of industrial waste sintering and bayer red muds for heavy metals.

The issue of heavy metal pollution is a critical global concern that requires urgent solution. However, conventional heavy metal adsorbents are too costly to be applied in large-scale engineering. In this study, adsorption behavior and mechanism of sintering red mud (RM-A) and bayer red mud (RM-B) for heavy metals were investigated to address the disposal of red mud as industrial waste and remediation of heavy metal pollution. Batch adsorption experiments were conducted to explore the adsorption performances of RM-A and RM-B under various conditions. Characterization of RM-A and RM-B before and after adsorption by XRD, FTIR and SEM-EDX was applied to investigate the specific adsorption behavior and mechanism. Adsorption experiments of both RM-A and RM-B fitted pseudo-second-order kinetic model and Langmuir isotherm model, with estimated maximum adsorption capacity of 21.96 and 25.19 mg/g for Cd2+, 21.47 and 26.06 mg/g for Cu2+ and 55.47 and 59.65 mg/g for Pb2+, respectively. Precipitation transformation of calcite was the primary adsorption mechanism for RM-A, whereas ion exchange of cancrinite, surface coordination compounds of hematite and minor precipitation transformation of calcite accounted for the adsorption mechanism for RM-B. Overall, RM-A and RM-B exhibited best adsorption performance for Pb2+, with RM-B showing greater adsorption capacity attributed to its higher specific surface area. This study compared the adsorption properties of RM-A and RM-B for the first time and demonstrated that both red muds can be effectively applied to remove heavy metals, thereby contributing to the sustainable industrial waste management and resourceful reuse.

Elucidating the separation role of C3N slit-pore on N2/CH4 in coalbed methane

A hybrid approach integrating molecular dynamics (MD) and Grand Canonical Monte Carlo (GCMC) simulations was employed to investigate the separation efficacy of N2/CH4 across various C3N slit apertures. MD simulations enabled the determination of separation selectivity and diffusion coefficients of N2/CH4, thereby aiding in the elucidation of the separation mechanism. On the other hand, GCMC simulations provided insights into the adsorption isotherms and isosteric heats of N2 and CH4 within the C3N slit. These findings reveal that the highest selectivity of N2 over CH4 occurs at the zigzag-edge C3N with a pore size of 6.2 Å. However, this selectivity is accompanied by the smallest diffusion coefficient, attributable to size sieving effects. As the pore diameter increases, more gas molecules can permeate into the pores, leading to a rise in both the maximum adsorption capacity and the isosteric heat of methane adsorption. With increasing pressure, gas molecules tend to reach saturation at higher pressure levels. Our study primarily centers on examining the separation of N2/CH4 across various C3N slit-pores, encompassing both adsorption and diffusion phenomena. These findings offer theoretical insights and comprehension for the experimental separation of coalbed methane utilizing cheaper carbon-based materials.