Matrix-assisted Laser Desorption/ionization Process Research Articles

Ionization detection of neutral 2,5-dihydroxy benzoic acid molecules in the matrix-assisted laser desorption/ionization plume by ultraviolet laser post-ionization: Correlation between internal energy distribution and thermal decomposition rate

We probed neutral 2,5-dihydroxy benzoic acid (DHB) crystals in the matrix-assisted laser desorption/ionization (MALDI) plume using ultraviolet (UV) laser post-ionization at 266 nm to investigate the initial MALDI process involving fast phase transitions. Mainly three ion signals, DHB+, [DHB–H2O]+ produced by the dissociative ionization of neutral DHB, and [DHB–CO2]+ formed by pyrolysis in the dense plume, were detected using time-of-flight mass spectrometry. The [DHB–H2O]+/DHB+ ratio was utilized as the fraction of highly excited neutral DHB molecules produced by photoexcitation and survived after phase explosion, and the [DHB–CO2]+/DHB+ ratio indicated the extent of pyrolysis of neutral DHB molecules in the thermally heated condensed phase before phase explosion. The two indexes showed an inverse relationship with respect to the laser delay corresponding to the position in the plume, i.e., the [DHB–H2O]+/DHB+ ratio revealed high values at the tip of the plume, whereas the [DHB–CO2]+/DHB+ ratio increased in the rear part of the plume, reflecting the molecular dynamics of solid-to-gas phase transition involving the production of most MALDI analyte ions.

Applying Automation and High-Throughput MALDI Mass Spectrometry for Peptide Metabolic Stability Screening

The discovery of peptide therapeutics represents a fast-growing segment of pharmaceutical research. During the early discovery process, a large number of peptide candidates needs to be rapidly screened for metabolic stability in relevant biological matrices. In most cases, peptide stability assays are quantified using LC-MS/MS, which may take hours to analyze 384 samples and generates liters of solvent waste. Herein, we introduce a high-throughput screening (HTS) platform for peptide stability assessment founded on Matrix Assisted Laser Desorption/Ionization (MALDI) mass spectrometry (MS). Full automation has been implemented for sample preparation with minimal manual intervention. The limit of detection, linearity, and reproducibility of the platform were evaluated, and metabolic stabilities have been determined for a number of peptide candidates. The MALDI-MS-based HTS workflow is able to analyze 384 samples in less than 1 h while only using 115 μL of total solvent. Although this process allows for very rapid assessment of peptide stability, given the nature of the MALDI process, it is noteworthy that spot-to-spot variations and ionization bias are observed. Therefore, LC-MS/MS may still be needed for confident, quantitative measurements and/or when the ionization efficiency of certain peptides is inadequate using MALDI.

Analysis of carbohydrates and glycoconjugates by matrix-assisted laser desorption/ionization mass spectrometry: An update for 2019-2020.

This review is the tenth update of the original article published in 1999 on the application of matrix-assisted laser desorption/ionization (MALDI) mass spectrometry to the analysis of carbohydrates and glycoconjugates and brings coverage of the literature to the end of 2020. Also included are papers that describe methods appropriate to analysis by MALDI, such as sample preparation techniques, even though the ionization method is not MALDI. The review is basically divided into three sections: (1) general aspects such as theory of the MALDI process, matrices, derivatization, MALDI imaging, fragmentation, quantification and the use of arrays. (2) Applications to various structural types such as oligo- and polysaccharides, glycoproteins, glycolipids, glycosides and biopharmaceuticals, and (3) other areas such as medicine, industrial processes and glycan synthesis where MALDI is extensively used. Much of the material relating to applications is presented in tabular form. The reported work shows increasing use of incorporation of new techniques such as ion mobility and the enormous impact that MALDI imaging is having. MALDI, although invented nearly 40 years ago is still an ideal technique for carbohydrate analysis and advancements in the technique and range of applications show little sign of diminishing.

Clean polycondensation through mechanochemistry: Catalyst-free production of new urea-citric acid copolymer

The copolymerization reaction of biodegradable monomers urea and citric acid was performed for the first time via mechanochemistry using a planetary mill with controlled variables analysis (time and stirring velocity). The copolymer was characterized by Infrared Spectroscopy (FTIR), Matrix-Assisted Laser Desorption Ionization Process - (MALDI-TOF), X-ray Crystallography – XRC, Nuclear Magnetic Resonance – NMR, Thermogravimetry Analysis – TGA, Differential Scanning Calorimetry– DSC and Scanning Electron Microscopy – SEM. The polymeric material was produced involving a selective reaction of the terminal units of the carboxylic acids of citric acid with urea, and the central COOH remained intact. The copolymerization reaction was also investigated under solution condition with water as solvent, to compare the polymer production performance in both conditions. The yield of urea-citric copolymer under mechanochemistry condition (82%) is superior to the solution condition (70%). The product has low molecular weight, high crystallinity, and good thermal stability, and these two characteristics are superior to the mechanochemical product in comparison to that produced in solution. In this way, it was demonstrated a technologically feasible, catalyst and solvent-free clean route to produce urea-citric copolymer using mechanochemistry, without the formation of wastewater.

ANALYSIS OF CARBOHYDRATES AND GLYCOCONJUGATES BY MATRIX-ASSISTED LASER DESORPTION/IONIZATION MASS SPECTROMETRY: AN UPDATE FOR 2015-2016.

This review is the ninth update of the original article published in 1999 on the application of matrix-assisted laser desorption/ionization (MALDI) mass spectrometry to the analysis of carbohydrates and glycoconjugates and brings coverage of the literature to the end of 2016. Also included are papers that describe methods appropriate to analysis by MALDI, such as sample preparation techniques, even though the ionization method is not MALDI. Topics covered in the first part of the review include general aspects such as theory of the MALDI process, matrices, derivatization, MALDI imaging, fragmentation and arrays. The second part of the review is devoted to applications to various structural types such as oligo- and poly-saccharides, glycoproteins, glycolipids, glycosides and biopharmaceuticals. Much of this material is presented in tabular form. The third part of the review covers medical and industrial applications of the technique, studies of enzyme reactions and applications to chemical synthesis. The reported work shows increasing use of combined new techniques such as ion mobility and the enormous impact that MALDI imaging is having. MALDI, although invented over 30 years ago is still an ideal technique for carbohydrate analysis and advancements in the technique and range of applications show no sign of deminishing. © 2020 Wiley Periodicals, Inc.

New Strategy to Preserve Phosphate by Ionic Liquid Matrices in Matrix-Assisted Laser Desorption/Ionization: A Case of Adenosine Nucleotides.

Adenosine -5′-triphosphate (ATP) plays a valuable role in metabolic activity to produce adequate energy in a biosystem. A high ATP/AMP ratio has a correlation with diabetes that induces suppression of AMP-activated protein kinase (AMPK). Matrix-assisted laser desorption/ionization (MALDI)–mass spectrometry (MS) has outstanding potential in determining the ratio of several types of adenosine phosphates in a sample to rapidly understand the primary energy transfer in metabolism. Although MALDI is viewed as a soft ionization technique for MS analysis, excess photon energy might crack the phosphate bonds leading to misinterpretation of the ATP level. In this work, ionic liquid matrices (ILMs) were employed to reduce fragmentation and increase the detection efficiency during the MALDI process. This study demonstrated for the first time that 2,5-dihydroxybenzoic acid pyridine (DHBP) is one of the most effective matrices for further quantitative analysis of adenosine nucleotides. This systematic screening of ILMs also enhances the fundamental understanding of MALDI.

Atmospheric-Pressure MALDI Mass Spectrometry Imaging at 213 nm Laser Wavelength.

First results for a new atmospheric-pressure matrix-assisted laser desorption/ionization (MALDI) mass spectrometry imaging source operating at 213 nm laser wavelength are presented. The activation of analytes in the 213 nm MALDI process at atmospheric pressure was evaluated and compared to results for 337 nm MALDI and electrospray ionization using thermometer molecules. Different sample preparation techniques for nicotinic acid, the matrix with the highest ionization efficiency at 213 nm of all tested matrices, were evaluated and optimized to obtain small crystal sizes, homogenous matrix layer sample coverage, and high ion signal gains. Mass spectrometry imaging experiments of phospholipids in mouse tissue sections in positive- and negative-ion mode with different lateral resolutions and the corresponding pre-/post-mass spectrometry imaging workflows are presented. The use of custom-made objective lenses resulted in sample ablation spot diameters of on average 2.9 μm, allowing mass spectrometry imaging experiments to be performed with 3 μm pixel size without oversampling. The ion source was coupled to an orbital trapping mass spectrometer offering high mass resolution (>100.000), high mass accuracy (≤ ±2 ppm), and high sensitivity (single pixel on-tissue tandem MS from 6.6 μm2 ablation area). The newly developed 213 nm atmospheric-pressure MALDI source combines the high mass resolution and high mass accuracy performance characteristics of orbital trapping mass spectrometers with high lateral resolution (pixel size ∼3 μm) mass spectrometry imaging.

Reactive Matrix-Assisted Laser Desorption/Ionization Mass Spectrometry Imaging Using an Intrinsically Photoreactive Paternò-Büchi Matrix for Double-Bond Localization in Isomeric Phospholipids.

The location and identity of phospholipids (PLs) within tissues can serve as diagnostic markers for tissue types or diseases. Whereas mass spectrometry imaging (MSI) has emerged as a powerful bioanalytical tool to visualize PL distributions, inferring PL identities from MSI experiments is challenging. Especially, C═C double-bond (DB) positions are not identifiable in most MSI experiments. Herein, we introduce benzophenone (BPh) as a novel reactive matrix for matrix-assisted laser desorption/ionization (MALDI). BPh promotes desorption/ionization and simultaneously serves as derivatization reagent that allows functionalization of unsaturated PLs during the MALDI process via a laser-light driven Paternò-Büchi (PB) reaction without the need for additional equipment. Using BPh, PB product ions of numerous PL classes are readily generated to pinpoint the location of DBs. High lateral resolution MSI results of DB-position isomers are presented, highlighting the capabilities of BPh as a PB-reactive MALDI matrix to potentially unveil the impact of DB-position isomers in PL metabolism.

Binding of Cu+ and Cu2+ with peptides: Peptides = oxytocin, Arg8‐vasopressin, bradykinin, angiotensin‐I, substance‐P, somatostatin, and neurotensin

The intrinsic binding ability of 7 natural peptides (oxytocin, arg8 -vasopressin, bradykinin, angiotensin-I, substance-P, somatostatin, and neurotensin) with copper in 2 different oxidation states (CuI/II ) derived from different Cu+/2+ precursor sources have been investigated for their charge-dependent binding characteristics. The peptide-CuI/II complexes, [M-(n-1)H+nCuI ] and [M-(2n-1)H+nCuII ], are prepared/generated by the reaction of peptides with CuI solution/Cu-target and CuSO4 solution and are analyzed by using matrix-assisted laser desorption/ionization (MALDI) time-of-flight mass spectrometry. The MALDI mass spectra of both [M-(n-1)H+nCuI ] and [M-(2n-1)H+nCuII ] complexes show no mass shift due to the loss of ─H atoms in the main chain ─NH of these peptides by Cu+ and Cu2+ deprotonation. The measured m/z value indicates the reduction of CuI/II oxidation state into Cu0 during MALDI processes. The number and relative abundance of Cu+ bound to the peptides are greater compared with the Cu2+ bound peptides. Oxytocin, arg8 -vasopressin, bradykinin, substance-P, and somatostatin show the binding of 5Cu+ , and angiotensin-I and neurotensin show the binding of 7Cu+ from both CuI and Cu targets, while bradykinin shows the binding of 2Cu2+ , oxytocin, arg8 -vasopressin, angiotensin-I, and substance-P; somatostatin shows the binding of 3Cu2+ ; and neurotensin shows 4Cu2+ binding. The binding of more Cu+ with these small peptides signifies that the bonding characteristics of both Cu+ and Cu2+ are different. The amino acid residues responsible for the binding of both Cu+ and Cu2+ in these peptides have been identified based on the density functional theory computed binding energy values of Cu+ and the fragment transformation method predicted binding preference of Cu2+ for individual amino acids.

Insights into the MALDI Process after Matrix Deposition by Sublimation Using 3D ToF-SIMS Imaging.

Imaging mass spectrometry (IMS) has become a powerful tool to characterize the spatial distribution of biomolecules in thin tissue sections. In the case of matrix-assisted laser desorption ionization (MALDI) IMS, homogeneous matrix deposition is critical to produce high-quality ion images, and sublimation in particular has shown to be an excellent matrix deposition method for the imaging of lipids. Matrix deposition by sublimation is, however, a completely solvent-free system, which ought to prevent the mixing of matrix and analytes thought to be necessary for successful MALDI. Using 3D time-of-flight secondary ion imaging mass spectrometry, we have studied the matrix-tissue interface in 3D with high resolution to understand the MALDI process of lipids after matrix deposition by sublimation. There is a strong indication that diffusion is the process by which lipids migrate from the tissue to the matrix layer. We show that triacylglycerols and phospholipids have a delayed migratory trend as compared to diacylglycerols and monoacylglycerols, which is dependent on time and matrix thickness. Additional experiments show that a pure lipid's capacity to migrate into the matrix is dependent on its fluidity at room temperature. Furthermore, it is shown that cholesterol can only migrate in the presence of a (fluid) lipid and appears to fluidize lipids, which could explain its colocalization with the diacylglycerols and monoacylglycerols in the matrix.

Characterization of ZnO Nanoparticles using Superconducting Tunnel Junction Cryodetection Mass Spectrometry.

Zinc oxide (ZnO) nanoparticles coated with either n-octylamine (OA) or α-amino poly(styrene-co-acrylonitrile) (PSAN) ligands (L) have been analyzed using laser desorption/ionization and matrix assisted laser desorption/ionization (MALDI) time-of-flight (TOF) superconducting tunnel junction (STJ) cryodetection mass spectrometry. STJ cryodetection has the advantage of high m/z detection and allows for the determination of average molecular weights and dispersities for 500-600 kDa ZnO-L nanoparticles. The ability to detect the relative energies deposited into the STJs has allowed for investigation of ZnO-L metastable fragmentation. ZnO-L precursor ions gain enough internal energy during the MALDI process to undergo metastable fragmentation in the flight tube. These fragments produced a lower energy peak, which was assigned as ligand-stripped ZnO cores whereas the individual ligands were at too low of an energy to be observed. From these STJ energy resolved peaks, the average weight percentage of inorganic material making up the nanoparticle was determined, where ZnO-OA and ZnO-PSAN nanoparticles are comprised of ~62% and ~68% wt ZnO, respectively. In one example, grafting densities were calculated based on the metastable fragmentation of ligands from the core to be 16 and 1.1 nm-2 for ZnO-OA and ZnO-PSAN, respectively, and compared with values determined by thermogravimetric analysis (TGA) and transmission electron microscopy (TEM). Graphical Abstract ᅟ.

Theoretical investigation of low detection sensitivity for underivatized carbohydrates in ESI and MALDI.

Electrospray ionization (ESI) and matrix-assisted laser desorption/ionization (MALDI) mainly generate protonated ions from peptides and proteins but sodiated (or potassiated) ions from carbohydrates. The ion intensities of sodiated (or potassiated) carbohydrates generated by ESI and MALDI are generally lower than those of protonated peptides and proteins. Ab initio calculations and transition state theory were used to investigate the reasons for the low detection sensitivity for underivatized carbohydrates. We used glucose and cellobiose as examples and showed that the low detection sensitivity is partly attributable to the following factors. First, glucose exhibits a low proton affinity. Most protons generated by ESI or MALDI attach to water clusters and matrix molecules. Second, protonated glucose and cellobiose can easily undergo dehydration reactions. Third, the sodiation affinities of glucose and cellobiose are small. Some sodiated glucose and cellobiose dissociate into the sodium cations and neutral carbohydrates during ESI or MALDI process. The increase of detection sensitivity of carbohydrates in mass spectrometry by various methods can be rationalized according to these factors. Copyright © 2016 John Wiley & Sons, Ltd.

Multidimensional mass spectrometry to characterize degradation products generated during MALDI of polystyrenes prepared by controlled radical polymerization techniques

An analytical workflow involving high resolution mass analysis, collision-induced dissociation and ion mobility was implemented to structurally characterize polymeric by-products detected in lieu of intact species when performing matrix-assisted laser desorption/ionization (MALDI) of polystyrenes with fragile end groups. Studied samples were prepared by atom transfer radical polymerization, reversible addition–fragmentation transfer polymerization and nitroxide-mediated polymerization. Spectral resolution enabled by orthogonal injection of MALDI ions into a reflectron time-of-flight mass analyzer allowed a thorough inventory of species, including some with the same nominal m/z value but different elemental composition. Individual end-group mass determination was achieved in MS/MS experiments, implementing an additional separative dimension based on ion mobility prior to CID to assist precursor ion selection in case of interferences. Besides validating commonly reported polystyrene chains terminated with either endo- or exo-double bond, this multidimensional approach permitted to show that initiating moiety could also be affected by the MALDI process. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016, 54, 3388–3397

High-resolution MALDI-TOF MS study on analysis of low-molecular-weight products from photo-oxidation of poly(3-hexylthiophene).

High-resolution matrix-assisted laser desorption/ionization (MALDI) time-of-flight mass spectrometry (TOF MS) was used for the analysis of the low-molecular-weight products from the photo-oxidation of poly(3-hexylthiophene) (P3HT) in solution and thin film. Eight new peak series were observed in the low-mass range of the mass spectra of the products degraded in solution, and the formulas of the eight components were determined from the accurate mass. From SEC/MALDI-TOF MS, two components were identified as the degraded products, and the other six components were derived from the fragmentation of the degraded products during the MALDI process. A mechanism for the formation of these components was proposed on the basis of the results of MALDI-TOF MS. For the thin film degradation, a part of products in the solution degradation were observed, which supports that the oxidation of P3HT in solution and thin film proceeded in the same mechanism. This study shows that high-resolution MALDI-TOF MS is effective for the analysis of the low-molecular-weight products from P3HT photo-oxidation and expected to be feasible for the degradation analyses of other polymers. Copyright © 2015 John Wiley & Sons, Ltd.

Sinapinic acid clusters distribution from monomer to mega Dalton’s region in MALDI process

In this work, we report the first complete sinapinic acid clusters distribution from monomer to mega Dalton’s region by matrix-assisted laser desorption/ionization (MALDI). A decrease of eight orders in intensity was observed from monomer ion to 10000-mer ion. The results fit to the model of laser ablation induced desorption process with bimodal power-law dependence. In addition, the detailed measurements on the populations of different sizes of clusters can provide some insight of different models of the mechanism for MALDI.

Role of three-body recombination for charge reduction in MALDI process

Ions in Matrix-Assisted Laser Desorption/Ionization (MALDI) are predominantly singly charged for small analyte molecules. With the estimated high number density and low temperature of electrons, the three-body recombination mechanism is attractive and should be considered as an important cause for the charge reduction in the plume. Theoretical calculations indicate that the rate coefficient of the three-body recombination is about 50 times higher than that of the two-body recombination if the analyte molecule has insufficient degrees of freedom. Experimental results show that, for small analyte molecules, the ratio of AH2(2+)/AH(+) is close to the theoretical 5% value from the three-body recombination modeling and this ratio declines with the increasing electron and matrix molecule number density caused by greater laser irradiance. The ratio of [A + 2](+)/[A + 1](+) is higher than the theoretical isotopic value, and the excess [A + 2](+) could exclusively result from the three-body recombination collisions. Further evidence demonstrates that [A + 2](+)/[A + 1](+) increases with electron number density, which is in correspondence with the model. All of these theoretical and experimental results indicate that three-body recombination is an essential charge reduction mechanism for small molecules in the MALDI plume.

In‐situ enrichment of phosphopeptides on MALDI plates modified by ambient ion landing

We report substantial in-situ enrichment of phosphopeptides in peptide mixtures using titanium and zirconium dioxide-coated matrix assisted laser desorption-ionization (MALDI) plates prepared by recently reported ambient ion landing deposition technique. The technique was able to modify four common materials currently used for MALDI targets (stainless steel, aluminum, indium-tin oxide glass and polymeric anchor chip). The structure of the deposited dioxide was investigated by electron microscopy, and different surfaces were compared and discussed in this study. Two standard proteins were used to test the enrichment capabilities of modified MALDI plates: casein and in-vitro phosphorylated trehalase. The enrichment of casein tryptic digest resulted in identification of 20 phosphopeptides (including miscleavages). Trehalase was used as a suitable model of larger protein that provided more complex peptide mixture after the trypsin digestion. All four possible phosphorylation sites in trehalase were identified and up to seven phosphopetides were found (including methionine oxidations and miscleavages). Two different mass spectrometers, MALDI-Fourier transform ion cyclotron resonance (FTICR) and MALDI-time of flight, were used to detect the phosphopeptides from modified MALDI plates after the enrichment procedure. It was observed that the desorption-ionization phenomena on the modified surfaces are not critically influenced by the parameters of the different MALDI ion sources (e.g. different pressure, different extraction voltages), and thus the presence of dioxide layer on the standard MALDI plate does not significantly interfere with the main MALDI processes. The detection of phosphopeptides after the enrichment could be done by both instruments. Desorption electrospray ionization coupled to the FTICR was also tested, but, unlike MALDI, it did not provide satisfactory results.

Robust Data Processing and Normalization Strategy for MALDI Mass Spectrometric Imaging

Matrix-assisted laser desorption/ionization (MALDI) mass spectrometry imaging (MSI) provides localized information about the molecular content of a tissue sample. To derive reliable conclusions from MSI data, it is necessary to implement appropriate processing steps in order to compare peak intensities across the different pixels comprising the image. Here, we review commonly used normalization methods, and propose a rational data processing strategy, for robust evaluation and modeling of MSI data. The approach includes newly developed heuristic methods for selecting biologically relevant peaks and pixels to reduce the size of a data set and remove the influence of the applied MALDI matrix. The methods are demonstrated on a MALDI MSI data set of a sagittal section of rat brain (4750 bins, m/z = 50-1000, 111 × 185 pixels) and the proposed preferred normalization method uses the median intensity of selected peaks, which were determined to be independent of the MALDI matrix. This was found to effectively compensate for a range of known limitations associated with the MALDI process and irregularities in MS image sampling routines. This new approach is relevant for processing of all MALDI MSI data sets, and thus likely to have impact in biomarker profiling, preclinical drug distribution studies, and studies addressing underlying molecular mechanisms of tissue pathology.

Special Issue:Advanced Techniques of MALDI-TOF MS in Ionization, Instrumentation and Applications.

I am glad to share with the many contributors and readers of this journal a special issue highlighting recent advances in MALDI-MS, which is the first published issue of a new journal from the Mass Spectrometry Society of Japan entitled Mass Spectrometry. I thank the editors, Prof. Yoshinao Wada and Prof. Toshifumi Takao, for providing me with the opportunity to highlight this important aspect of science of mass spectrometry. Over twenty years have passed already since the first report of soft ionization in matrix-assisted laser desorption/ionization (MALDI) MS. These days, researchers can identify target molecules by using MALDI-MS without having to consider what actually happens during the MALDI process. Moreover, life scientists desire to know when, where, and how various biomolecules are expressed and work in cells, tissues, and organs. Material scientists also want to investigate solid-surface chemistry of their materials, and their studies may require time and space resolving analytical instruments. To provide an ideal molecular imaging system, MALDI-MS has been developed as an imaging MS system in biology and material sciences. Polymer scientists require highly sensitive and high-resolution instruments to estimate the fine distributions within mixtures and the degree of polymerization. MALDI-MS has proven to be an essential tool in all of these fields, and it has great potential for scientists who hope to develop new applications and basic technologies, and to gain further scientific knowledge. This special issue contains articles describing new applications of imaging mass spectrometry in cell and plant biology. The combination of MALDI-MS and other scientific techniques such as micro-scale manipulation systems and microscopes, will be critical to develop and improve innovative new techniques and applications. On the other hand, important and essential aspects of developing new MALDI applications include basic studies of ionization mechanisms, matrices, fragmentation processes, and so on. For instance, both in-source and post-source decay in the MALDI process are significant topics because we can obtain additional and/or complementary structural information from each other. Interestingly, in-source and post-source decay of analytes depend on the matrix properties. Even matrices themselves are an important research target, and mechanisms of co-crystal formation are also of great interest. Finally I would like to express my sincere appreciation to all contributors of this special issue of the new journal Mass Spectrometry to reach to readers in wide ranging fields.

Compelling Evidence for Lucky Survivor and Gas Phase Protonation: The Unified MALDI Analyte Protonation Mechanism

This work experimentally verifies and proves the two long since postulated matrix-assisted laser desorption/ionization (MALDI) analyte protonation pathways known as the Lucky Survivor and the gas phase protonation model. Experimental differentiation between the predicted mechanisms becomes possible by the use of deuterated matrix esters as MALDI matrices, which are stable under typical sample preparation conditions and generate deuteronated reagent ions, including the deuterated and deuteronated free matrix acid, only upon laser irradiation in the MALDI process. While the generation of deuteronated analyte ions proves the gas phase protonation model, the detection of protonated analytes by application of deuterated matrix compounds without acidic hydrogens proves the survival of analytes precharged from solution in accordance with the predictions from the Lucky Survivor model. The observed ratio of the two analyte ionization processes depends on the applied experimental parameters as well as the nature of analyte and matrix. Increasing laser fluences and lower matrix proton affinities favor gas phase protonation, whereas more quantitative analyte protonation in solution and intramolecular ion stabilization leads to more Lucky Survivors. The presented results allow for a deeper understanding of the fundamental processes causing analyte ionization in MALDI and may alleviate future efforts for increasing the analyte ion yield.