Material Combinations Research Articles

Investigations of strength and quality of clinched joints using digital image correlation

ABSTRACT This study examines the impact of processing conditions on joint strength and the effectiveness of digital image correlation (DIC) in detecting failure points in clinched joints. Mechanical tests, including single-lap shear and pull-out tests, were conducted using DIC to evaluate joint quality in various clinched configurations. The results showed frequent failures at the neck rejoin in clinched joints between mild steel and aluminum sheets, particularly when thinner sheets were positioned on the punch side and softer materials on the die side. DIC effectively identified defects and failure locations, offering insights into material combinations, sheet positioning, and failure modes. Although DIC was useful in detecting defects in both elastic and destructive regions, its ability to distinguish specific defect types from strain contour maps was limited. The study highlights the need for further research to extend DIC’s application to other mechanical joining systems and advocates for its proactive use in refining designs and manufacturing processes.

Simulation-Based Design for Recycling of Car Electronic Modules as a Function of Disassembly Strategies

Modules (or parts) of a car are a complex functional material combination used to deliver a specified task for a car. Recovering all materials, energy, etc., into high-grade materials at their end of life (EoL) is impossible. This is dictated by the second law of thermodynamics (2LT) and thence economics. Thus, recyclability cannot be conducted with simplistic mass-based approaches void of thermodynamic considerations. We apply, in this paper, a process simulation model to estimate the true recyclability of various SEAT (Volkswagen Group) car parts within the EU H2020 TREASURE project. This simulation model is developed with 190 reactors and over 310 feed components with over 1000 reaction species in the 880 streams of the flowsheet. The uniqueness of the work in this paper is to apply the full material declaration (FMD) and bill of materials (BOM) of all 310 materials in the parts as a feed to the process simulation model to show the parts’ true recyclability. We classified all parts into categories, i.e., copper-rich, steel-rich and plastic-rich, to maximally recover metals at the desired material quality, as well as energy. Recyclability is understood to create high-grade products that can be applied with the same functional quality in these parts. In addition, disassembly strategies and related possible redesign show how much recyclability can be improved. Process simulation permits the creation of alloys, phases, materials, etc., at a desired quality. The strength of the simulation permits any feed from any End-of-Life part to be analyzed, as long as the FMD and BOM are available. This is analogous to any mineral and metallurgical engineering process simulation for which the full mineralogy must be available to analyze and/or design flowsheets. This paper delivers a wealth of data for various parts as well as the ultimate recovery of materials, elements, and energy. The results show clearly that there is no one single recycling rate for elements, materials, and alloys. It is in fact a function of the complexity and material combinations within the parts. The fact that we use a thermochemical-based process simulator with full compositional detail for the considered parts means full energy balances as well as exergy dissipation can be evaluated. This means that we can also evaluate which parts, due complex mixtures of plastics, are best processed for energy recovery or are best for material and metal recovery, with thermochemistry, reactor technology and integrated flowsheets being the basis.

Fuel Cell Catalyst Layers with Platinum Nanoparticles Synthesized by Sputtering onto Liquid Substrates.

Platinum (Pt) nanoparticles are widely used as catalysts in proton exchange membrane fuel cells. In recent decades, sputter deposition onto liquid substrates has emerged as a potential alternative for nanoparticle synthesis, offering a synthesis process free of contaminant oxygen, capping agents, and chemical precursors. Here, we present a method for the synthesis of supported nanoparticles based on magnetron sputtering onto liquid poly(ethylene glycol) (PEG) combined with a heat-treatment step for attachment of nanoparticles to a carbon support. Transmission electron microscopy imaging reveals Pt nanoparticle growth during the heat-treatment process, facilitated by the carbon support and the reducing properties of PEG. Following the heat treatment, a bimodal size distribution of Pt nanoparticles is observed, with sizes of 2.5 ± 0.8 and 6.7 ± 1.8 nm, compared to 1.8 ± 0.4 nm after sputtering. Synthesized Pt nanoparticles display excellent specific and mass activities for the oxygen reduction reaction, with 1.75 mA/cm2 Pt and 0.27 A/mgPt respectively, measured at 0.9 V vs the reversible hydrogen electrode. The specific activities reported herein outperform literature values of commercial Pt/C catalysts with similar loading and are on par with values of bulk Pt and mass-selected nanoparticles of comparable size. Also, the mass activities agree well with the literature values. The results provide new insights into the growth processes of SoL-synthesized carbon-supported Pt catalyst nanoparticles, and most crucially, the high performance of the synthesized catalyst layers, along with the possibility of nanoparticle growth through a straightforward heat-treatment step at relatively low temperatures, offer a scalable new approach for producing fuel cell catalysts with more efficient material utilization and new material combinations.

Unraveling Interdiffusion Phenomena and the Role of Nanoscale Diffusion Barriers in the Copper-Gold System.

Diffusion is one of the most fundamental concepts in materials science, playing a pivotal role in materials synthesis, forming, and degradation. Of particular importance is solid state interdiffusion of metals which defines the usable parameter space for material combinations in the form of alloys. This parameter space can be explored on the macroscopic scale by using diffusion couples. However, this method reaches its limit when going to low temperatures, small scales, and when testing ultrathin diffusion barriers. Therefore, this work transfers the principle of the diffusion couples to small scales by using core-shell nanowires and in situ heating. This allows us to delve into the interdiffusion dynamics of copper and gold, revealing the interplay between diffusion and the disorder-order phase transition. Our in situ TEM experiments in combination with chemical mapping reveal the interdiffusion coefficients of Cu and Au at low temperatures and highlight the impact of ordering processes on the diffusion behavior. The formation of ordered domains within the solid-solution is examined using high-resolution imaging and nanodiffraction including strain mapping. In addition, we examine the effectiveness of ultrathin Al2O3 barrier layers to control interdiffusion of the diffusion couple. Our findings indicate that a 5 nm thick layer serves as an efficient diffusion barrier. This research provides valuable insights into the interdiffusion behavior of Cu and Au on the nanoscale, offering potential applications in the development of miniaturized integrated circuits and nanodevices.

Optimization and analysis of Si/SiGe strained vertically stacked heterostructure on insulator FeFinFET for high performance analog and RF applications

As semiconductor technology advances, the exploration of novel materials and device architectures becomes imperative to meet the growing demands of integrated circuits for analog and radio-frequency (RF) applications. In this paper, various advanced technologies have been amalgamated such as integration of ferroelectric layer in multigate FinFET along with the adaptation of SOI technology. Further strain technology is also used which employs a tri-layered strained-silicon channel system with the help of SiGe to form Vertically Stacked Heterostructure on Insulator Ferroelectric based FinFET (VS-HOI-FeFinFET) and on comparison with baseline FeFinFET, it is found to show remarkable improvements in terms of various measured parameters such as drain current, switching ratio, threshold voltage and subthreshold swing. Subsequently, gate stacking architecture is incorporated in VS-HOI-FeFinFET to further optimize the device performance. The four different configurations C1 to C4 are taken in terms of four different combinations of gate stack materials considered for gate oxide such as C1(SiO2+Al2O3), C2(SiO2+HfO2), C3(Al2O3), and C4(Al2O3+HfO2). It is found that the static and analog performance of VS-HOI-GS-FeFinFET enhance sequentially from configuration C1 to C4 such as switching ratio is enhanced upto around 5 times, DIBL and quality factor are improved by around 41% and 58% respectively along with significant improvement in device efficiency, early voltage, intrinsic gain, output conductance and output resistance. Subsequently performance optimization of VS-HOI-GS-FeFinFET with variation in mole fraction of germanium is also explored for various analog metrics. Further, several RF parameters are also explored and it is observed that the gain frequency product (GFP) and gain transconductance frequency product (GTFP) are augmented by around three times in magnitude along with 16% reduction in the unity gain cut off frequency in C4 configuration, exhibiting its ability of high frequency amplification with minimized noise distortion thus makes the device suitable for various high performance Analog and RF applications.

Mechanical properties and damage mechanism of SMAHC laminates

Abstract The combination of smart materials and composite materials to achieve lightweight and intelligent structures has been an important research direction in recent years. In this paper, a three-dimensional woven hybrid shape memory alloy (SMA actuator) is modularly implanted into a composite laminate to prepare a SMA hybrid composite (SMAHC) laminate. The orthogonal test was designed with the three variables of SMA actuator modular implantation position, SMA pre-strain and SMA number. According to the orthogonal test results and finite element results, the influence of the three variables on the stiffness before heating, the stiffness change rate after heating and the strength of SMAHC laminates was studied. According to the test index, the influence of the three variables on the results was further evaluated. The results show that the implantation position has the greatest influence on the mechanical properties of SMAHC laminates, followed by SMA pre-strain, and the number of SMA has the least influence. The location and form of damage of SMAHC laminates are further summarized, and the bending damage mechanism of SMAHC laminates is analyzed.

Digital analysis of internal fit variation of additively manufactured crown patterns

Aim: The purpose of this study was to digitally quantify the consistency and variation of printed resin crown patterns produced by different 3D printers, aiming to evaluate their clinical relevance and accuracy. This was accomplished by evaluating patterns manufactured using three different 3D printers and resin materials, assessing their fit and adaptation through digital scanning and analysis. The objective was to determine the internal and marginal variations of printed crown resin patterns and to identify the printer and material combinations that produce the most consistent and clinically acceptable results. Methods: A prefabricated typodont tooth was prepared for a crown and scanned using an intraoral scanner. From this scan, a crown was designed and the resulting STL file was exported. This 3D file was manufactured using resins indicated for castable patterns on 3 different printers: FotoDent® Cast with the Carbon M2 printer, Form 3 Castable with the Form 2 printer, and Siraya Tech Cast with the ELEGOO Mars 2 Pro 3D printer. Finally, the crown resin patterns were scanned using an intraoral digital scanner (3Shape TRIOS 3) scanner, and crown adaptation was digitally quantified in GeoMagic software. Clinically relevant significance was determined (marginal gap < 50 µm) between resin patterns printed on different printers. Results: Form 3 Castable/Form 2 printer had the lowest mean internal variation at all measurement areas, 21.07 μm at the occlusal, 104.23 μm at the margin, and 37.98 μm at the axial. FotoDent® Cast/Carbon M2 had the largest marginal variation while Siraya Tech Cast/ELEGOO Mars 2 Pro had the largest occlusal variation. Within each material, the largest internal variation was at the marginal area while the lowest value was in the occlusal area. Conclusions: All printed crowns displayed clinically acceptable ranges, but there was a statistically significant difference in the fit between all printers.

Comparing Gendered Exposure and Impact in Online Election Violence: Tunisian Political Candidates Targeted on Facebook

Abstract Election violence is increasingly taking place online. However, we still do not know much about how such attacks affect the representation of politically marginalized groups such as women. This article develops and applies strategies for analyzing (gendered) exposure to and impacts of online attacks against political candidates. It focuses on the 2019 parliamentary election campaign in Tunisia and combines manual analysis of Tunisian candidates’ public Facebook pages with candidate interviews. We find no gendered patterns in exposure to online election violence in the Facebook data and a low general exposure to attacks. The interview data nevertheless suggests gendered perceptions and impacts of attacks, as well as a perception among the candidates that online election violence is widespread and problematic. These discrepancies highlight that we need a combination of methods and materials to capture the multifaceted nature of online election violence, and in particular those that directly link candidate exposure to impact.

Wireless, Programmable, and Refillable Hydrogel Bioelectronics for Enhanced Diabetic Wound Healing.

Diabetic wounds, characterized by complex pathogenesis and high infection rates, pose significant challenges in treatment due to prolonged recovery times and high recurrence rates, often leading to severe complications such as amputation and death. Traditional dry dressing treatments fail to address the unique microenvironment of diabetic wounds and tend to cause secondary damage due to frequent replacement. In this study, an electronic-embedding, drug-loading hydrogel bioelectronics is reported for accelerating diabetic wound healing using a combination of programmable pharmaceutical and electrostimulative approaches. Encapsulated in stretchable and biocompatible materials, this device is capable of multiple drug refilling and accelerated drug release modulated by on-board electronics. In vivo experiments on diabetic model rats confirm the device's effectiveness in promoting wound healing. This innovative approach implies the potential for improving diabetic wound management using a combination of physical, material, and pharmaceutical interventions.

Industrial picosecond pulse laser welding of stainless-steel to quartz for optical applications

We report on the development of a robust picosecond laser welding process for the industrially relevant material combination of quartz and stainless steel. The process requires high numerical aperture focusing of a 6 ps 1030 nm laser through the transparent quartz onto the interface between the two materials. It is found that increased mechanical pressure applied during welding increases reliability and weld performance and with the correct choice of welding parameters parts will survive ISO standard thermal cycling and vibration testing demonstrating the suitability of the process for industrial application.

Effects of environmentally friendly soil remediation materials on soil quality and maize production

In the precent, the reclaimed raw soil of newly renovated abandoned homestead was considered as the research object, and study the effects of different environmentally friendly soil remediation material combinations on the quality of reclaimed raw soil and maize crop production. A total of 6 improved material treatments were set up, including decomposed chicken manure(YJ), fly ash(FMH), ferrous sulfate curing agent(SHJ), ferrous sulfate curing agent+organic fertilizer (SYJ), fly ash+decomposed chicken manure(FYJ), and control treatment(CK). The research results showed that, the organic carbon content and water storage of new reclaimed raw soil exhibited a significant increasing trend after the application of different environmentally friendly modified materials(P < 0.05). Among them, the organic carbon and water storage of reclaimed soil under FYJ improved, which increased by 132.3 and 14.4 %, respectively compared with CK. During the growth period of summer maize, the plant height and yield exhibited a trend of FYJ> SYJ> YJ> FMH> SHJ> CK. The yield of maize under SYJ and FYJ treatments increased by 38.8 and 53.4 %, respectively, compared with CK. The appropriate combination of environmentally friendly soil remediation materials is helpful to improve the quality of new reclaimed raw soil, promote soil carbon sequestration, increase the comprehensive utilization rate of waste resources, increase the production performance of crops, and help rural revitalization and beautiful rural construction. Bangladesh J. Bot. 53(3): 673-679, 2024 (September) Special

Toward mechanical recyclability of high barrier food packaging films through filler incorporation on the EVOH layer

AbstractTo preserve food from moisture and oxygen, polymers, such as ethylene vinyl alcohol (EVOH) are used in multilayer structures to provide oxygen barrier, while low‐density polyethylene (LDPE) is used for a water vapor barrier. While this material combination is functionally ideal, it may not comply with the new packaging recycling guidelines. Some European markets have implemented rules that limit the weight percentage of EVOH in LDPE films. One way to increase recyclability is by reducing the amount of EVOH in the film structure while maintaining the packaging's oxygen barrier properties. To achieve this, it is necessary to improve the barrier properties of EVOH. With this objective in mind, this study evaluated the incorporation of nanoclays (NC), cellulose microcrystals (MCC), silicon dioxide nanoparticles (SiO2), and cellulose nanocrystals (CNC) into an EVOH matrix. The results indicate that NC and MCC facilitate a stable blown film extrusion process and have a better dispersion in the EVOH matrix. Based on this finding, three‐layer films (with an ABA configuration) consisting of LDPE (A) and EVOH (7 μm layer) with 0.5 or 1 wt.% MCC or NC (B) were produced to protect the EVOH from moisture and enable blown film processing. The oxygen transmission rate (OTR) values were lowest for 0.5 wt.% NC and 1 wt.% MCC incorporation. Although the films with micro and nanoparticles had increased haze, this did not affect the visibility of the packaged food.

Fracture toughness in SPCC/CFRP hybrid laminates: Mode I and mode II perspectives

Hybrid composites using adhesive joints are gaining popularity in various industries as their various material combinations can create certain advantages. This research focuses on examining the mode I and mode II fracture toughness characteristics of the combined laminate between Steel Plate Cold Rolled Commercial (SPCC) metal and Carbon Fiber Reinforced Polymer (CFRP) composite processed using adhesive bonding. SPCC/CFRP hybrid laminate composites were manufactured with a variety of manufacturing options (A, B, and C) to find the most optimal method using two types of epoxy and cyanoacrylate adhesives, with two different bonding processes: secondary bonding and co-bonding. Fracture toughness values were measured through the Double Cantilever Beam (DCB) test for mode I and the End Notched Flexure (ENF) test for mode II. The test results showed that epoxy adhesives in the SPCC/CFRP adhesive joints provided better fracture toughness performance, especially when combined with the co-bonding technique. Specimens from manufacturing option C showed the highest GIC and GIIC values of 83.05 and 254.94 J/m2, respectively. These values increased by 58.98 % and 80.48 % compared to manufacturing options A and B in Mode I. Additionally, the GIIC value for manufacturing option C increased by 78.00 % and 66.76 % compared to manufacturing options A and B. The SPCC/CFRP hybrid laminates showed adhesive failure on the SPCC surface when using epoxy adhesive, whereas adhesive failure occurred on the CFRP surface with cyanoacrylate adhesive for the different manufacturing options.

Selection of suitable filter materials for subsurface flow constructed wetland systems for wastewater treatment in rice noodle handicraft village

This study aims to select suitable filter materials for Subsurface Flow Constructed Wetlands (SSF CW) to treat wastewater from rice noodle handicraft villages, based on a combination of new materials (plastic waste and rice husk) and traditional substrates (limestone, gravel, and sand). Four SSF CW models using different filter materials were tested during three months, including CW1 (limestone, gravel, and sand), CW2 (sand, plastic waste, and gravel), CW3 (sand + rice husk, limestone, and gravel), and CW4 (sand + rice husk, plastic waste, and gravel). The results indicated that CW3 and CW4 systems were more effective to plant growth. Replacing limestone with plastic waste did not show a significant difference in treatment efficiency (p > 0.05), however the addition of rice husk decreased the efficiency of organic matter treatment while increasing nutrient treatment efficiency (p < 0.05). The highest treatment efficiencies for TSS and COD were observed in CW1, at 83.89 ± 1.38 % and 79.56 ± 1.36 %, respectively. Meanwhile, the highest treatment efficiencies for TN, NH4+, and TP were recorded in CW4, at 80.14 ± 2.76 %, 88.39 ± 1.62 %, and 82.22 ± 2.51 %, respectively. The effluent water from all four SSF CW models met the Vietnamese standard for wastewater quality (QCVN 40:2011/BTNMT, column B). This study demonstrates the potential of using a combination of plastic waste, rice husk, and sand as suitable filter substrates for SSF CW in treating wastewater from rice noodle handicraft villages.

Development of Fiber-Reinforced Polymer Composites for Additive Manufacturing and Multi-Material Structures in Sustainable Applications

This study investigates the mechanical properties of carbon and natural fiber-reinforced Polylactic Acid (PLA) and Polyethylene Terephthalate Glycol (PETG) composites produced via Additive Manufacturing (AM), focusing on Material Extrusion (MEX). The performance of filaments made from pre-consumer recycled PLA (rPLA) and PETG, with varying weight percentages of hemp and jute short fibers, was evaluated through tensile testing. Comparisons were made between the original filaments (PLA, carbon fiber-reinforced PLA [CF–PLA], and PETG) and their recycled versions. Multi-material compositions—neat PLA and PETG, single-graded (PLA + CF–PLA, PETG + CF–PETG), and multi-gradient (PLA + CF–PLA + PLA, PETG + CF–PETG + PETG)—were analyzed for mechanical properties. Optical microscope images of multi-material specimens were captured before and after fracture to assess failure mechanisms. The results indicate that the original CF–PETG filaments achieved a tensile strength of 50.14 MPa, which is higher than rPLA, PLA, and CF–PLA by 2%, 70%, and 6.7%, respectively. The re-manufactured PLA filaments reinforced with 7 wt% hemp fibers exhibited a tensile strength of 38.8 MPa, representing a 29% increase compared to the original PLA filaments and a 26% improvement over recycled PLA. Additionally, incorporating 7% jute fiber into PETG resulted in a tensile strength of 62.38 MPa, reflecting a 12% improvement over the original PETG filaments and a 15% increase compared to the recycled PETG filaments. Among specimens produced by AM, CF–PLA and rPLA demonstrated the highest tensile and compressive strengths. However, multi-material composites showed reduced mechanical performance compared to neat PLA and PETG, highlighting the need for improved interlayer adhesion. This study emphasizes the importance of optimizing material combinations and fiber reinforcement to enhance the mechanical properties of composites produced through AM.

3D bi-directional auxetic square metastructure with programmable thermal expansion and Poisson's ratio

Multifunctional integration research on metastructures has become the current development trend and hotspot, especially satellite platforms and hypersonic aircraft in the aerospace field. A 3D bi-directional auxetic square metastructure (BASM) with the programmable coefficient of thermal expansion (CTE) and Poisson's ratio (PR) is designed through the combination of re-entrant hexagonal structures and bi-material triangles. Specimens in the form of the 1*2 array are designed and fabricated through 3D printing. The correctness of the results of finite element analysis (FEA) of the BASM is verified by uniaxial compression experiments. Additionally, FEA is adopted to investigate the effective mechanical properties of the BASM with the form of the 2*3 array, and deformation mechanisms are further explored. Results indicate that the CTE, PR, and stiffness of the BASM depend on material combinations and geometric parameters. Under thermal and mechanical loads, the BASM achieves bi-directional regulation of the CTE and PR, encompassing both axial and circumferential deformations. Notably, the deformation mechanisms and critical conditions of the BASM are explored under the thermo-mechanical load. A novel strategy for programming the PR of the BASM is proposed in addition to changing the geometric parameters and the material combinations.

Fatigue properties of a Ti–5Al–5Mo-5 V–3Cr alloy manufactured by electron beam powder bed fusion

AbstractAdditive manufacturing (AM) is a modern way of manufacturing structures, which tends to have fewer design limitations than those manufactured by conventional processes such as casting or forging. A combination of high-strength materials and small and complex structures opens up a wide range of potential applications, especially in the fields of medicine and aerospace. Titanium and its alloys show a very beneficial combination of density and mechanical properties. One of these alloys is the metastable β titanium alloy Ti– 5Al–5Mo–5 V–3Cr (Ti-5553), which is currently used mainly for large forged structures like landing gears of airplanes. In this study, for the first time the fatigue behavior of electron beam powder bed fused (PBF-EB) Ti-5553 was investigated with a focus on the defects created by the layer wise manufacturing. To understand the defect structure and its respective influence on the fatigue behavior, all specimens were scanned prior to fatigue testing using a state-of-the-art µ-focus CT. The specimens were subjected to two heat treatment procedures commonly used in technical applications, which were aiming for high strength (solution treated and aged—STA) as well as high ductility (beta annealed, slow cooled and aged—BASCA). Results indicate that the fatigue strength of PBF-EB manufactured Ti-5553 is significantly reduced compared to conventionally manufactured Ti-5553. The main reason for this are defects, which have varying critical effects depending on the heat treatment of the specimen and the defect size, shape, location and type.

One‐Step Room Temperature Synthesis of Printable Carbon Quantum Dots Ink for Visual Encryption and High‐Performance Photodetector

AbstractCarbon quantum dots (CQDs) have emerged as promising materials for optoelectronic applications and have garnered much interest as potential competitors to conventional inorganic or hybrid semiconductor quantum dots because of carbon's intrinsic merits of high stability, low cost, and environment‐friendliness. The ability of easy formulation of functional ink of CQDs is necessary for the development of industrial‐scale, reliable, inexpensive printing/coating processes, for its full exploitation in the ever‐growing class of applications in sensors, optoelectronics, and energy storage and conversion. Here a facile one‐step room‐temperature synthesis of printable, fluorescent CQD ink is demonstrated. The as‐synthesized fluorescent CQD ink is used for invisible fingerprint stamps, printing of micro‐patterns, and soft lithographic patterning with a resolution down to 1.5 µm. This functional CQD ink is also used to fabricate a high‐performance CQD‐ZnO heterojunction ultraviolet (UV) photodetector with a photo‐responsivity of 3.85 A W−1, detectivity of 6.78 × 1010 Jones, and an external quantum efficiency (EQE) of 15.3%. The enhanced device performance can be attributed to CQD's high photocurrent generation efficiency and rational combination of the asymmetric electrode materials. This work enables a high‐temperature stable CQD fluorescent ink synthesis method to fulfill the processing requirements of printing and soft lithographic patterning for visual encryption and optoelectronics.

Adjustable Humidity Response: Ultrahigh Green EMI Shielding Gel with Double‐Side Constant Temperature Capability

AbstractWith the increasingly serious secondary pollution of electromagnetic waves (EMWs), efficient green shielding materials have become an urgent need. MXene is widely used in electromagnetic interference (EMI) shielding due to its large surface area and high conductivity. Here, this work constructs MXene islands with better shielding performance through viscosity control and continuous mechanical stirring. Benefiting from the MXene islands, Janus‐structural gel with humidity response is successfully prepared, showing controllable ultrahigh green shielding property (up to 100.5 dB, thickness of 2 mm). Interestingly, this gel can spontaneously adjust its water content according to the humidity, resulting in a reversible transformation in three states to meet the needs of different environments. By Janus‐structural design and reasonable material combination, this gel demonstrates excellent electrothermal (rise to 111.6 °C, 5 s, 2 V)/thermal insulation (thermal conductivity is low to 0.029 W m−1 K−1) properties to meet the needs of shielding in underwater/fire operations.

Inert Liquid Exfoliation and Langmuir-Type Thin Film Deposition of Semimetallic Metal Diborides.

Graphite is one of only a few layered materials that can be exfoliated into nanosheets with semimetallic properties, which limits the applications of nanosheet-based electrodes to material combinations compatible with the work function of graphene. It is therefore important to identify additional metallic or semimetallic two-dimensional (2D) nanomaterials that can be processed in solution for scalable fabrication of printed electronic devices. Metal diborides represent a family of layered non-van der Waals crystals with semimetallic properties for all nanosheet thicknesses. While previous reports show that the exfoliated nanomaterial is prone to oxidation, we demonstrate a readily accessible inert exfoliation process to produce quasi-2D nanoplatelets with intrinsic material properties. For this purpose, we demonstrate the exfoliation of three representative metal diborides (MgB2, CrB2, and ZrB2) under inert conditions. Nanomaterial is characterized using a combination of transmission electron microscopy, scanning electron microscopy, atomic force microscopy, IR, and UV-vis measurements, with only minimal oxidation indicated postprocessing. By depositing the pristine metal diboride nanoplatelets as thin films using a Langmuir-type deposition technique, the ohmic behavior of the networks is validated. Furthermore, the material decomposition is studied by using a combination of electrical and optical measurements after controlled exposure to ambient conditions. Finally, we report an efficient, low-cost approach for sample encapsulation to protect the nanomaterials from oxidation. This is used to demonstrate low-gauge factor strain sensors, confirming metal diboride nanosheets as a suitable alternative to graphene for electrode materials in printed electronics.