Martensitic Structure Research Articles

Formation of requirements for impact resistance and wear resistance of grinding balls

The article presents the results of a study of the operation processes of steel grinding balls in semi-autogenous grinding mills (SAG). It was determined that the balls experience both abrasive and impact loads. The properties of steel grinding balls with the same production technology are determined by the chemical composition and the formed microstructure over the entire cross-section of the ball. Balls made using 3 different technologies were studied. The balls of sets 1 and 2 show high hardness values at the surface, sufficient to ensure good resistance to wear during operation, and a sharp decrease in hardness at a distance of ~(15–20) mm from the surface as the volume of pearlite structures increases. At the same time, the balls of the 1st and 2nd sets showed low values of impact strength and insufficient resistance to impact. The lowest hardness values from the surface to the center were observed for set 3. Also, the highest mass loss during the abrasive wear test was recorded for set 3, which is explained by the lowest hardness values. The balls of set 3 showed higher values of impact strength and no splitting during the ball-on-ball test, which is explained by the soft ferrite-pearlite structure both on the surface and across the cross section of the ball, due to the reduced carbon content and the presence of nickel in the chemical composition. At the same time, the balls from set 3 showed the worst result in terms of abrasive wear. In the course of the conducted research, it was established that for successful operation in SAG, steel grinding balls must have a surface with high hardness due to the martensitic structure and a viscous core with a ferrite-pearlite structure. A promising direction in the development of technology for the production of steel grinding balls will be to obtain a steel ball microstructure that decreases uniformly from the surface to the center, which will allow maintaining high wear resistance and increasing the resistance to ball splitting

Examination of Microstructure, Mechanical Properties, and Fatigue Strength in a Wire Arc Additively Manufactured Material Comprising Dissimilar Materials: AISI 316L Stainless Steel and Carbon Steel

This study provides a comprehensive investigation into the microstructure, hardness, tensile strength, and bending fatigue behavior of a Wire Arc Additively Manufactured (WAAM) component composed of dissimilar materials—Carbon Steel (CS) and 316L stainless steel. Microscopic analysis reveals distinct microstructural characteristics, such as equiaxed ferrite grains in WAAM CS and a coarse columnar structure with delta-ferrite phases in WAAM 316L. A macroscopic phase map indicates a predominantly Body-Centered Cubic (BCC) structure near the interphase, suggesting element migration between CS and 316L due to high heat input. Higher magnification scans highlight martensitic structures on both sides of the interphase, with the CS side exhibiting larger grain sizes. Hardness assessment along the built direction shows a peak hardness of 407 HV near the interphase on the 316L side, contrasting with the CS side's average interphase hardness of 316 HV due to larger grain sizes. The yield strength of both WAAM CS and WAAM dissimilar material was consistently measured at 392 MPa. In comparison, WAAM 316L exhibited a slightly lower yield strength of 359 MPa. Notably, WAAM 316L demonstrated the highest tensile strength among the materials, reaching 656 MPa. Meanwhile, WAAM CS displayed a robust tensile strength of 503 MPa, and the WAAM dissimilar material exhibited a yield strength of 520 MPa. In terms of elongation, WAAM CS and WAAM 316L showcased values of 44.9% and 49.6%, respectively. On the other hand, WAAM dissimilar material exhibited a somewhat lower elongation of 20.4%, suggesting a different mechanical behavior in terms of ductility. Bending fatigue tests on WAAM 316L, WAAM CS, and the dissimilar material reveal a fatigue limit of approximately 225 MPa for WAAM 316L, 210 MPa for WAAM CS, and approximately 210 MPa for the dissimilar material. In the low-cycle and medium-cycle regimes, the dissimilar material exhibits slightly superior fatigue strength, potentially due to its marginally higher static strength. Notably, consistent fractures on the CS side during fatigue tests underscore a recurring behavior in the dissimilar material.

The effect of cryogenic treatment on a high Co bearing DIN 1.2888 steel used as die in hot forging process

Abstract Hot work steels used as dies in metal forming processes must endure harsh conditions, typically achieved through a martensitic structure. However, retained austenite can persist after martensitic transformation, negatively impacting mechanical properties. Cryogenic treatment (CT) refines martensite, reduces retained austenite, and increases fine carbide density, thus enhancing performance. DIN 1.2888, a hot work tool steel with high cobalt content (~10%) and low carbon content (~0.2%), is less studied concerning the effects of CT. The objective of this study was to investigate how cryogenic treatment affects the mechanical and microstructural properties of DIN 1.2888 steel. Samples underwent conventional heat treatment (HT) and CT at -100, -140, and -180°C for 6 hours, followed by double tempering. Various analytical methods, including X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS), and Vickers Microhardness tests, were used to examine the samples. Wear mechanisms were evaluated through pin-on-disc tests under different loads, and impact toughness was measured both at room temperature and the working temperature of dies (350°C). Results indicated that lowering the cryogenic treatment temperature resulted in a slight increase in hardness values from 507HV for the heat-treated sample to 529HV for the sample treated at -180°C. Additionally, the impact toughness improved significantly, with values rising from 12.35J for the heat-treated sample to 23.44J at 350°C for the cryogenically treated sample at -180°C. Wear rates also decreased by approximately 50%, particularly at higher cryogenic treatment temperatures. The improvement in wear resistance was attributed to finer carbide precipitation and a more homogeneous distribution of carbides. These findings suggest that deep cryogenic treatment has a positive effect on DIN 1.2888 steel by decreasing retained austenite and increasing fine carbide density, leading to enhanced mechanical properties and extending the lifespan of the steel in die applications.

New route for fabricating low-carbon ductile martensite to optimize the stretch-flangeability of dual-phase steel

Traditional cold-rolling dual-phase steel (CR sheet), limited by poor stretch-flangeability as indicated by the hole expansion rate (HER), faces challenges in manufacturing complex automobile parts. To address this, a new type of hot-rolling dual-phase steel with an 800 MPa grade (manufactured by tyipical thin slab continuous casting and rolling process, TSCCR) was designed to replace the traditional one. The TSCCR sheet, with a lower carbon content of 0.047wt.%, compared to 0.093wt.% in the CR sheets, features 40.6% martensite significantly higher than 28.2% in the CR sheet. This increased martensite content, despite being softer and more ductile due to its low hardness, compensates for the tensile strength in the TSCCR sheet. Furthermore, the TSCCR sheet exhibits a unique heterostructure characterized by uneven carbon distribution from the ferrite/austenite interface to other boundaries/interfaces, estimated by the negligible partition local equilibrium (NPLE) model of ferrite transformation. This unique heterostructure diminishes the mechanical disparity between ferrite and martensite, resulting in a higher yield strength of 568 MPa, compared to 456 MPa in the CR sheet. During uniaxial tension, the ferrite and ductile martensite in the TSCCR sheet initiate cooperative plastic deformation earlier than in the CR sheet, despite initially having fewer favorable slip systems in the TSCCR martensite. The low working hardening rate of the TSCCR sheet facilitates the forming layered structure of ferrite and martensite during necking compared to the CR sheet. Consequently, the HER of the TSCCR sheet sharply increased by 144% compared to the CR sheet. This enhancement in HER can be attributed to the crack initiation area, longer crack propagation path, and higher crack propagation resistance facilitated by the ductile martensite, culminating in superior HER.

Effect of Rare Earth Ce on Structure and Properties in 7CrSiMnMoV Die Steel Castings

In this study, rare earth (RE) Ce is used to modify the interaction between atoms in 7CrSiMnMoV die steel castings. The tensile properties are performed, and strengthening mechanism are analyzed by investigated fracture surface, and microstructure by optical microscopy (OM) and scanning electron microscope‐energy dispersive spectrometer (SEM‐EDS). And ab initio molecular dynamics (AIMD) is used to simulate the effect of the Ce element on the local atomic structure of the FeCeC system alloy steel. The results indicate the strength can increase from 722.55 to 1074.27 MPa, and the elongation can increase from 24.86% to 44.22% with a RE Ce concentration of 0.009%. It is attributed to that doping of Ce can inhibit the formation of network eutectic cementite, refine the lamellar spacing of pearlite, and even form granular cementite and martensite structures. AIMD simulation results show that C atoms tend to be surrounded by Fe, and the strong chemical bonds of FeC make the Fe‐centered C more stable with an increase in RE Ce concentration. And doping Ce can introduce new local topological and chemical orderings such that the FeCFe triplets predominantly form small and big angles shifting from near 75° and 136° to 47° and 81°, respectively.

Eutectic resolidification and ultrafast self-quenching of the microstructure in the surface layer of high-speed steel by scanning electron beam treatment

Improving the service life and efficiency of high-speed steel (HSS) tools remains a formidable challenge. Herein, scanning electron beam (SEB) was employed to modify the surface of M2 HSS. Results revealed that SEB induced eutectic resolidification and ultrafast self-quenching of microstructure in surface layer of HSS. The melted layer exhibited a microstructure comprising martensite, residual austenite, dispersed finely rod-like MC and lamellar M2C eutectic carbides along grain boundaries. Martensite and eutectic carbide grid structure significantly enhanced the hardness and wear resistance of surface layer. Compared to substrate, the microhardness of SEB sample was elevated by more than threefold, reaching 914.7HV0.2, which exceeded the hardness (828.6HV0.2) of conventional quenching treatment. Notably, the wear volume of SEB sample had been reduced to 0.54 × 10−11 m3, resulting in a wear resistance that was 3.8 times greater than that of quenched sample.

Microstructural Evolution of P92 Steel with Different Creep Life Consumptions After Long-Term Service

P92 steel is widely used in ultra-supercritical units due to its excellent high-temperature performance. This paper studies the microstructure of P92 steel steam pipes in three conditions: as-supplied, after 80,000 h of service at 67.06 MPa stress, and after 100,000 h of service at 80.28 MPa stress. After prolonged service, the P92 steel retains its martensitic structure, but the lath width increases and the dislocation density decreases. In addition to M23C6, MX, and Laves phases, Z phase was also observed among the precipitates. The results indicate that the sizes of M23C6 and Laves phases increase with the progression of creep life consumption, with the coarsening rate of Laves phase being significantly higher than that of M23C6. However, the coarsening of MX phase is not evident. Compared to the Laves phase, the formation of the Z phase requires a longer period of time. The precipitation of the Z phase consumes MX carbonitrides, and it has been observed that the Z phase precipitates from the MX phase, with the two phases exhibiting a coexisting state.

Effect of Tempering Temperature on the Aqueous Corrosion Resistance of 9Cr Series Heat-Resistant Steel

In this investigation, the aqueous corrosion resistance of 9Cr series heat-resistant steel during tempering was investigated. Optical Microscopy (OM), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectrometer (EDS) were used to analyze the effect of tempering temperature on the microstructure and precipitation behavior of precipitates. The heat-resisting steel was heated to 1150 °C for 1 h, and then tempered at different temperatures between 680 °C and 760 °C for 2 h. The microstructure of the heat-resistant steel after tempering was composed of lath-tempered martensite and fine precipitates. The hardness decreased with increasing tempering temperature, ranging from HBW 261 to HBW 193. The aqueous corrosion resistance improved as the tempering temperatures increased from 680 °C to 720 °C but deteriorated at higher temperatures, such as 760 °C, which was obtained by an electrochemical corrosion performance test. The aqueous corrosion resistance was affected by the decrease in dislocation density and the decrease in Cr solution in the tempered martensite. With the increase in the tempering temperature, the aqueous corrosion potential first increases and then decreases, the self-corrosion current density first decreases and then increases, and the polarization resistance first increases and then decreases. Furthermore, the increase in corrosion resistance is attributed to the reduction in dislocation density and chromium depletion in the martensitic structure as the tempering temperature approaches 720 °C. This paper reveals the effect of tempering temperature on the corrosion resistance of 9Cr series heat-resistant steel, which is a further exploration of a known phenomenon.

Austenite-martensite interfacial patterns and energy dissipation of phase transformation in Ni-Mn-Ga single crystal

The martensitic phase transformation occurs in Shape Memory Alloys (SMA) via the nucleation/propagation of the Austenite-Martensite interface (A-M interface), which is a transition region (domain) between the two coexisting phases. For providing compatibility, the transition region consists of various martensitic twin structures (laminates), forming different interfacial patterns, such as parallel laminates and branching laminates. Due to the energy accumulation in the interfacial structures (e.g., elastic mismatch and twin-boundary surface energy), the interfacial patterns should be relevant to the driving force (energy dissipation) and the associated kinetics of the phase transformation. In this paper, we adopt a special thermal loading, small-temperature-gradient “heating-cooling-reheating”, to control the A-M interface's forward and reverse propagation to generate different interfacial patterns in a Ni-Mn-Ga single crystal SMA with the observation on the twin structures (by optical microscope and SEM) and the InfraRed measurement on the temperature hysteresis of the interface propagation (for characterizing the thermal driving force). Simple energetic analysis indicates that the thermal driving force (energy dissipation) is directly related to the stored energy in the interfacial structure, particularly the large mismatch elastic energy near the habit plane. This study not only provides the details of the various interfacial patterns and their dependence on the loading path, but also indicates the driving force and the associated mechanism about the pattern evolution to understand the phase transformation process.

Microstructure evolution by thermomechanical processing and high-temperature mechanical properties of HCP-high entropy alloys (HEAs)

The solid solution strengthening and deformation mechanisms of the hcp-high entropy alloys (HEAs) have not been elucidated yet because of the complexity introduced by the martensite structure, particularly in alloys undergoing phase transformation from bcc to hcp structures. This study attempted to fabricate an equiaxed hcp microstructure for TiZrHf, TiZrHfAl, and TiZrHfAlSc using the hot rolling process and subsequent heat treatment. The equiaxed hcp phase was successfully formed in TiZrHfAl, but the martensite structure remained in TiZrHf and TiZrHfAlSc. The 0.2 % proof stress at 400 and 600°C increased with the increase of the average atomic size misfit δ and the mixing entropy . The low activation volume and high-stress exponent of TiZrHfAl with equiaxed hcp phase at room temperature suggest minor obstacles such as cluster or short-range order inhibit the movement of dislocation and leading to the significant solid-solution strengthening. However, the effect diminished at 600 °C.

تأثير استعمال ليزر النيوديميوم ياك (Nd-YAG) على البنية الدقيقة وصلابة سطح الفولاذ AISI1012

The unique characteristics of the laser beam such as directionality, monochromaticity, and brightness make it a very important tool in the surface treatment engineering. The concentrated heat in the laser beam can be precisely directed toward the processed region on the surface. The laser beam power, beam size, and scanning velocity are easily controlled during the different processing methods. Laser surface modifications of metallic materials, such as laser surface melting, laser surface alloying, and laser cladding are some of the most important methods to improve the mechanical properties of the processed layer on the surface. A pulsed Nd-YAG laser surface melted specimens of low carbon steel with a maximum power of 90W at different processing parameters. The rapid melt and solidification of the treated layer produced a refinement in the microstructure. The original microstructure of this steel (Ferrite + Pearlite) has been transformed to new phases of martensitic and bainitic structures. The melted layer consists of the melted pool, the heat affected zone, and the substrate. The maximum hardness of the laser melted layer is more than 400 HV. The effect of different lasers such as high power CW CO2 laser on the mechanical properties and corrosion resistance of steel alloys will be carried out in future studies. Keywords: Nd-Yag Laser, Laser surface treatment, Microstructure and hardness of AISI1012 steel

ANALYSIS OF THE QUALITY OF THE RESTORED GEAR TOOTH OF LARGE-MODULE GEARS

This study examines the quality of a gear tooth surface fragment restored through electric arc welding. Visual inspection revealed a defect-free, dense surface. Macrostructure examination displayed uniformity and absence of cracks in the metal sample. The high hardness (HRC-36.61) of the weld deposit is crucial for wear resistance, while the base metal, with lower hardness (HRC-29.09), ensures ductility and impact toughness. Martensitic and residual austenitic structures in the weld deposit indicate deformation-resistant properties, with austenite providing good ductility and martensite contributing to high hardness and strength, making the material resistant to wear and deformation under dynamic loads. Thin lens-like martensitic plates and a reed-like structure suggest unique formation characteristics during electroslag welding’s oxidizing-reducing reactions. Microstructure analysis revealed a finer structure in the weld deposit compared to the base metal. The base metal exhibited a ferrite-pearlite structure typical of many steels, unchanged after welding. The weld deposit showed elevated carbon (0.70 %) and manganese (1.38 %) concentrations, typical for weld deposits, influencing mechanical properties. Elements like manganese and molybdenum enhance wear resistance, while the presence of chromium (0.42 %) and nickel (0.12 %) improves corrosion resistance, crucial in aggressive environments. Keywords: large-module gears, tooth wear, electro slag surfacing, hardness, analysis

Variations of VHCF Characteristics by Microstructure of a Spring Steel to UNSM Treatment

<i>The bainitic structure resulting from the austempering of spring steel exhibits high strength and ductility. On the other hand, there appears to be no study on the effects of very high cycle fatigue (VHCF) and ultrasonic nanocrystal surface modification (UNSM) of this bainite structure. Therefore, this study compared the fatigue properties of VHCF using spring steel with bainitic and martensitic structures and bearing steel data. This study analyzed the characteristics of microstructure transformation associated with the heat treatment cycles and studied and evaluated the fatigue strength characteristics because of the UNSM in terms of fracture mechanics method and fracture surface analysis through electron backscatter diffraction, scanning electron microscopy fracture analysis, and energy-dispersive spectroscopy analysis. The fatigue limit of UNSM-treated spring steel was improved significantly by approximately 33% to 50% compared to the fatigue test results of the untreated material in the VHCF. In the long life range of bainized spring steel, fish-eye cracks appear in the form of the fine granular area, and fatigue cracks occur in the form of fish-eye cracks that occur in the bainite facet and matrix, resulting in a significant increase in fatigue strength and fatigue life.</i>

Influence of Immersion Orientation on Microstructural Evolution and Deformation Behavior of 40Cr Steel Automobile Front Axle during Oil Quenching.

This study employs the finite element method to investigate the microstructural evolution and deformation behavior of a 40Cr steel automobile front axle during the quenching process. By establishing a multi-physics field coupling model, the study elucidates the variation patterns of the microstructure field in the quenching process of the front axle under different immersion orientations. It is found that along the length direction, the bainite and martensite structures decrease from the center to the edge region, while the ferrite structure shows an increasing trend. Additionally, the influence of immersion orientation on the hardness of the front axle's microstructure and deformation behavior is thoroughly discussed. The results indicate that, firstly, when quenched horizontally, the hardness difference among different regions of the front axle is approximately 8.2 HRC, whereas it reaches 10.3 HRC when quenched vertically. Considering the uniformity of the microstructure, the horizontal immersion method is preferable. Secondly, due to the different immersion sequences in different regions of the front axle leading to varying heat transfer rates, as well as the different amounts of martensite structures obtained in different regions, the deformation decreases along the length direction from the center to the edge region. Horizontal immersion quenching, compared to vertical immersion, results in a reduction of approximately 56.2% and 48.9% in deformation on the representative central cross-section (A-A) and the total length of the front axle, respectively. Therefore, considering aspects such as microstructure uniformity and deformation, the horizontal immersion quenching orientation is more favorable.

Strengthening mechanisms in vanadium-microalloyed medium-Mn steels

In this work, the impact of adding vanadium, ranging from 0 to 2 wt%, on the microstructure and mechanical properties of as-cast medium manganese steel was explored. A dual phase microstructure consisting of martensite and retained austenite was observed in the 0 V, 0.05 V and 0.8 V conditions. The 2 V condition contained retained austenite, lath martensite, and δ-ferrite bands. The retained austenite fraction and prior austenite grain size initially increased at lean vanadium concentrations but significantly dropped at the highest vanadium concentration. The element distribution in the constituent phases was investigated in detail. Mn, C and Si partitioning to austenite was observed in the 0 V, 0.05 V and 0.8 V conditions. V and C segregation to the grain boundaries and significant grain refinement were evident in the 2 V condition. The findings also revealed that increasing the vanadium content led to an increase in the hardness of the steel. This assessment was validated by tensile testing, which showed an improvement in yield and tensile strength of the steel with increasing vanadium content, and were supported by reconstruction of the parent austenite grains employing martensitic structures. Finally, the influence of different strengthening mechanisms on the yield strength of as-cast, microalloyed medium-manganese steels was also discussed in terms of simulated stacking fault energy, as well as the quantitative contributions from solid solution, grain boundary, and precipitation strengthening mechanisms.

Analyzing the effect of different shielding atmospheres on fiber laser welding parameters for modified 9Cr-1Mo steel

The present research aims to investigate the influence of and the relationship between welding speed ( v), focal position ( FP), and laser power ( LP) as input parameters for fiber laser to weld P91 under pure argon and CO2 shielding atmospheres using response surface methodology and using the desirability approach; optimization of input parameters has been performed to maximize the depth of penetration ( DP) while minimizing the top bead width ( TW) and heat-affected zone width ( HW). The results indicate that laser power ( LP) has the most significant impact on depth of penetration ( DP), whereas welding speed ( v) affects top bead width ( TW) and heat-affected zone width ( HW). The optimal combination of parameters under argon shielding results in a significantly low heat input of 48 J/mm (0.048 kJ/mm) and 50 J/mm (0.050 kJ/mm) pure argon and CO2 shielding atmospheres, respectively. Despite the difference in heat input being only 4.08%, an 11.618% increase in DP is observed under the CO2 shielding atmosphere. Due to the high-speed nature of the welding process (argon: 82.65 mm/s and CO2: 79.283 mm/s) combined with the significant reduction in heat input, the heat-affected zone is limited to a mere width of 0.203 mm under an argon shielding atmosphere and 0.263 mm under the CO2 shielding atmosphere compared with that reported in the other welding processes without the dissolution of precipitates in the fusion boundary of heat-affected zone. Microstructural characterization of the fusion zone has revealed the presence of an untempered lath martensite structure with precipitate dissolution. The precipitate dissolution has resulted in grain coarsening of 47.76% in argon weld and 39.65% in CO2 weld compared with the base metal grain size of 6.07 µm.

Composition dependence of phase transformation and shape memory effect of Ti-Zr-Pd-Pt high temperature shape memory alloys

Ti-Zr-Pd-Pt alloys have been considered as potential candidates for high-temperature shape memory alloys (HT-SMAs). In this study, nine alloys were prepared to investigate the effect of multi-component alloying on the phase transformation and shape memory effect. The structural phase diagram of martensite in Ti–Zr–Pd–Pt quaternary alloys was firstly systematically investigated to provide insights and predictions for further research. The phase transformation is divided into three groups: typical martensitic transformation (MT) area, supercooling-controlled phase transformation area and diffusion-assisted phase transformation area. The martensite structure changes from B19 to B33 with the addition of Zr over 25 %. The contribution of Pt contents to raising the martensitic transformation temperature (MTT) became less pronounced with increasing Zr contents. As for shape recovery, over 87 % shape recovery was obtained even under 300 MPa in Ti-10Zr-Pd-Pt alloys, among which Ti-10Zr-15Pt-35Pd presents the highest recovery ratio of over 97 %.

Особенности тонкой структуры Ni-Al покрытий, полученных методом HV-APS

Introduction. Development of Ni-Al intermetallic compounds is one of the priority directions of modern machine building. Due to such characteristics as high heat resistance, high temperature strength, and low density, nickel aluminides are used as functional coatings in the aerospace industry. The main methods of Ni-Al coating surfacing are High-Velocity Oxygen-Fuel and High-Velocity Air-Fuel spraying (HVOF and HVAF), atmospheric plasma spraying (APS) and its modification such as High-Velocity Atmospheric Plasma spraying (HV-APS) which provides non-equilibrium cooling conditions. Since there are eight different intermetallic compounds, as well as martensite transformation, Ni-Al coatings is quite interesting to study. The work purpose is to study the features of the martensitic structure in HV-APS coatings, and also to establish the effect of heating temperature on its decomposition. Materials and methods. Ni-Al coatings were surfaced onto a low-carbon steel substrate using the HV-APS method. Studies of the fine structure of the coatings were carried out using transmission electron microscopy (TEM). In addition, the influence heating temperature on structural transformations of the coatings was analyzed. Results and discussion. Two types of particles are formed in HV-APS coatings: with a dendritic and granular structure. The most part of HV-APS coatings consists of particles with a two-phase grain structure (NiхAl1-х and γ'-Ni3Al grains). Only NiхAl1-x grains undergo martensitic transformation at cooling. Martensite in large grains (sizes greater than 500 nm) has a lamellar structure, while small grains are completely transformed into one martensite plate. In addition, the coatings contain grains in which martensite plates (NiхAl1-х) and β-phases alternated. It is shown the behavior of martensitic plates at colliding with each other, as well as with the γ′-Ni3Al grain. Heating up to 400 °C contribute the begins of martensite decomposition in individual grains with the release of a secondary phase; after heating up to 600 °C all martensite dissolves.

A comparative study of the microstructure and shape memory behaviour of NiTi, NiTiHf, and Pt-added NiTiHf alloys

The microstructure, substructure, transformation temperature, and recovery ratio of a novel Ni45Pt 5 Ti30Hf20 alloy are reported in the current work. The properties of binary TiNi and ternary TiNiHf alloys are also characterized to establish a comparative basis for shape memory behaviour. The microstructure of the cast structure of Ni45Pt5Ti30Hf20 alloy showed a dendritic matrix and interdendritic eutectic-like mixture, and that of the homogenized structure consisted of martensitic matrix and secondary phase of dark contrast having the composition (Ti+Hf)2(Ni+Pt). Pt substitution of Ni in the ternary alloy with 20 at.% Hf by 5 at.% leads to a decrease in the Af, As, Ms, and Mf . Ms and Mf represent the temperatures at which austenite to martensite transformation starts and completes, respectively, while As and Af represent the temperatures at which martensite to austenite transformation starts and completes, respectively. The XRD studies showed that the structure of martensite is B19′ and TEM studies showed that the substructure of martensite in Pt modified NiTiHf alloy is similar to that of ternary NiTiHf alloy. The shape memory recovery of the Pt-modified alloy is similar to the ternary alloy at higher strength levels. The recovery ratio determined using Vickers indentation is compared with that determined using compression tests to provide an efficacy of small volume tests for screening of these alloys.

Mechanical Properties of P91 Steel (X10CrMoVNb9-1) during Simulated Operation in a Hydrogen-Containing Environment.

P91 steel (X10CrMoVNb9-1) is widely used in the energy industry. It is characterized by good mechanical properties, creep resistance, corrosion resistance, impact toughness, and resistance to thermal fatigue. Due to their operating conditions and martensitic structure, components made from P91 steel are often subject to damage related to the presence of hydrogen. This article compares the results of the mechanical properties evaluation for P91 steel in an aggressive solution charged under load and without load. Based on the research, it was found that the hydrogen environment significantly affects the mechanical properties of P91 steel, reducing strength and yield strength, and decreasing ductility. It was revealed that in samples tested after 72 h without preloading, the tensile strength decreased by 1.5%, and the elongation decreased by about 29% for the sample, compared to the delivered condition sample. Under loaded conditions, the difference in tensile strength increased by approximately 8%, while elongation increased by nearly 50.