Volume Fraction Of Martensite Research Articles

A temperature dependent constitutive model for functional fatigue in shape memory alloys

Functional fatigue is a vital aspect when considering the design of components made with shape memory alloys, since it can affect their short- and long-term behavior. With this in mind, a constitutive model considering the functional fatigue in shape memory alloys is developed. The functional fatigue is based on the residual strain, residual stress, residual martensite and a defect volume fraction, which are assumed to all evolve in a similar manner. The evolution is prescribed based on a saturation differential equation which is exponentially dependent on temperature. The residual martensite and defect volume fraction are defined to influence the development of hardening through a hardening energy term and the reduction in dissipation with an appropriate limit function. The model is validated by simulating several experiments of cyclic isothermal and isobaric tests. A fit and prediction is also offered for a set of complex thermomechanical loading paths. The results demonstrate the strong applicability of the model to capture the degradation of the transformation response associated with cyclic loads, even when different temperatures and loads are applied. Moreover, the results point out areas of improvement, such as the use of a logarithmic evolution for the saturation of the internal variables.

Effect of Cooling Rate on The Microstructure And Cryogenic Impact Toughness of HAZ in 9% Ni Steel

The effects of cooling rate on the microstructure and cryogenic impact toughness of coarse-grained heat-affected zone (CGHAZ) and inter-critically reheated coarse-grained HAZ (IC CGHAZ) in 9% Ni steel were investigated. CGHAZ and IC CGHAZ specimens were prepared from 9% Ni steel by controlling the cooling rate of the simulated welding process. The microstructure of the CGHAZ specimens consisted of autotempered martensite and lath martensite. As the cooling rate increased, the volume fraction of the autotempered martensite and the effective grain size decreased. A large amount of fine carbides was distributed inside the auto-tempered martensite, the dislocation density was low, and high angle grain boundaries were not observed. The microstructure of the IC CGHAZ specimens consisted of tempered martensite and lath martensite. As the cooling rate increased, the volume fraction of the tempered martensite and effective grain size decreased. Finer carbides were distributed inside the tempered martensite than in the auto-tempered martensite, the dislocation density was low, and high angle grain boundaries were not observed. Cryogenic fracture revealed that ductile fracture occurred in the auto-tempered martensite and tempered martensite, and brittle fracture occurred in the lath martensite. The crack propagation path was zig-zag in the high angle grain boundaries of the lath martensite. The volume fraction of auto-tempered martensite and tempered martensite and the effective grain size in the HAZ specimens had a significant effect on cryogenic impact toughness. In the IC CGHAZ specimens, cryogenic impact toughness decreased and then became constant as the cooling rate increased, due to a decrease in the volume fraction of the tempered martensite and effective grain size.

Modified strain gradient analysis of microscale dynamic response suppression of SMA-composite microplates featuring 2D superelastic phase transformations and kinematic nonlinearity

In contrast to all the previous researches, a 3D transformation model is used here instead of the less accurate 1D models for the energy dissipation/pseudoelasticity response evaluation of the shape memory alloy (SMA) wire-reinforced-composite plates in the microscale world, for the first time. The governing equations are developed by incorporation of the modified strain gradient theory (MSGT) in the principle of minimum total potential energy. The governing equations are extended further to account for the kinematic nonlinearity as well. The extra spatial differentiation orders of the MSGT and the nonlinearity of the governing equations are treated by a highly accurate 48-degrees-of-freedom element and an updating approach. A bridging rule and Lagoudas’s phase evolution algorithm are extended to the microscales by changing the stress and strain definitions. The extracted time variations of the lateral deflections and martensite volume fraction elucidate that higher energy dissipations and phase transformations may be obtained in smaller characteristic lengths and smaller thicknesses. Moreover, the higher vibration modes are amplified drastically in microscales in a manner that may not happen in macro-mechanics but the resulting energy dissipation magnitudes are slightly smaller in the microscale world due to the significant stiffening that happens in that subspace.

Flow and fracture of austenitic stainless steels at cryogenic temperatures

In this paper, we have characterized the microstructural evolution and the plastic flow and fracture behaviours of AISI 304L and AISI 316LN stainless steel grades at liquid nitrogen temperature (77K) and at liquid helium temperature (4K). Uninterrupted tensile experiments, where the sample is continuously deformed under quasi-static loading conditions until fracture, have been carried out with a Single-Section Sample to obtain the stress–strain characteristics of the two grades. Interrupted tensile experiments, in which the sample is unloaded before fracture, have been performed with a novel Double-Section Sample to later characterize the strain-induced martensitic transformation at different levels of deformation. The content of martensite has been determined post-mortem, using magnetic induction, electron backscatter diffraction and quantitative light optical micrography. The results obtained with the three methods show quantitative agreement, and reveal that the martensitic transformation in AISI 304L occurs faster and to a greater extent than in AISI 316LN both at 77K and at 4K. To the authors’ knowledge, in this paper we provide the first experimental results for the evolution of the content of strain-induced martensite in AISI 304L and AISI 316LN samples tested at liquid helium temperature. In addition, the experimental data for the evolution of the martensite volume fraction with the strain have been used to identify the temperature-dependent parameters of the martensitic transformation kinetic model proposed by Olson and Cohen (1975). Moreover, Mode I fracture tests with fatigue-precracked Compact Samples have been carried out to determine the fracture properties of the two investigated materials using the “resistance curve procedure” (ASTM-E1820-20a). The crack-growth resistance curves have been obtained with four different methods here referred to as ASTM Compliance Method, W–N Compliance Method, Modified W–N Compliance Method and ASTM Normalization Method, which is an original methodological contribution of this paper. While the four approaches yield similar results for the fracture toughness, only the W–N Compliance Method and the Modified W–N Compliance Method, the latter being proposed in this paper, fulfil all the requirements of the standard ASTM-E1820-20a so that the calculated fracture toughness can be accepted as a material property. The comparison of results for both materials and testing temperatures shows that AISI 316LN displays higher fracture toughness than AISI 304L. Moreover, post-mortem microstructural analysis of the Compact Samples near the fracture surface has revealed that the content of martensite is greater in AISI 304L than in AISI 316LN. Furthermore, for AISI 304L more martensite is formed in the sample tested at 77K because the plastic deformation near the crack is more than at 4K.

Study on the Compressive Stress Retention in Quenched Cam of 100Cr6 Steel Based on Coupled Thermomechanical and Metallurgical Modeling.

The assembled camshaft has obvious advantages in material optimization and flexible manufacturing. As the most important surface modification technique, the heat treatment process is utilized in this work to promote the desired compressive residual stress on the near-surface of the 100Cr6 steel assembled cam. The Johnson-Mehl-Avrami equation and Koistinen-Marbuger law are integrated into the ABAQUS software via user subroutines to simulate the evolution of diffusional transformation and diffusionless transformation, respectively. The linear mixture law is used for describing the coupled thermomechanical and metallurgical behaviors in the quenching of steel cam. The influences of various quenchants and the probable maximum phase volume fractions on surface residual stress or hardness are analyzed. Results show that a greater amount of martensite volume fraction and a slower martensitic transformation rate are beneficial for the compressive stress retention. Compared with the conventional quenching oil, the fast oil quenched cam surface has higher final compressive stress and hardness.

Microstructural characteristics of fusion zone in continuous wave fiber laser welded Nb-modified δ-TRIP steel

Welding processes were accomplished by means of a 600 W Continuous Wave (CW) fiber laser instrument in bead on plate manner with 60, 80 and 100 J mm−1 heat inputs. δ-TRIP Steel samples were similar in chemical composition and only contained different Nb (40Nb: 0.040 & 72Nb: 0.072 wt.% Niobium) amounts. Elevation of heat input resulted in changes in microstructure and hardness properties, which are desirable for welders to guarantee safe joints in engineering structures. An increase in the heat input can lead to reduction of the austenite in weld metals of both steel sheets. The reduction of the austenite could be attributed to the increase in δ-ferrite volume fraction which was induced by availability of sufficient time for segregation of aluminum and formation of more dendrite structured δ-ferrite at lower cooling rates. Increase in δ-ferrite content results in decreasing austenite content required for transformation of austenite to martensite. The direct consequence of a decrease in the martensite volume fraction is reduction of hardness. It is shown that an increase in the heat input from 60 to 100 J mm−1 results in reduction of hardness difference between weld and base metals by 40% and 37% for 40Nb and 72Nb steels respectively.

A new phenomenological constitutive model for shape memory alloys

A new thermomechanical constitutive modeling approach for shape memory alloys (SMAs) that undergo a martensite to austenite phase transformation and the associated pseudoelastic and shape-memory responses is presented. The novelty of this new formulation is that a single transformation surface is implemented in order to capture the forward and reverse phase transformations, as well as the reorientation and detwinning of the martensite phase. The framework is akin to the usual flow theory plasticity with kinematic hardening, however in addition to the transformation strain there is also a transformation entropy that is directly related to the martensite volume fraction appearing in prior theories. A transformation surface in effective stress and effective temperature space is introduced and an associated flow rule governs the evolution of the transformation strain and entropy. In order to capture the multitude of SMA behaviors, a transformation potential function is introduced in transformation strain and entropy space for the derivation of the back stresses and back temperatures that define the kinematic hardening behavior. It is this potential function that governs all of the important behaviors within the model. After the description of the general theory, specific forms for the transformation surface and the transformation potential are devised and results for the behaviors captured by the model are provided for a range of thermomechanical loadings. Finally, the model is implemented in the finite element method and applied to the pseudoelastic and shape memory effects of a beam in pure bending.

A new nonlinear finite element model for transient dynamic response of a micro composite plate embedded with micro SMA wires considering the size effects

In this research, a nonlinear dynamic analysis of micro plate containing micro shape memory alloy (SMA) wires, taking into account the material and geometric nonlinear effects and also considering the instantaneous changes of martensitic volume fraction (MVF) in different points of the micro plate, has been investigated. In this study, using the first-order shear deformation theory (FSDT) and applying Hamilton's principle, the governing equations of micro plate are extracted such the kinematic equations of micro SMA wires are coupled with governing equations. In this regard, von Karman nonlinear strain-displacement relation is used to consider large displacements and the model proposed by Hernandez and Lagoudas is employed to model the pseudoelastic behavior and also to capture the size effect of the SMA wires at micro scale. The modified couple stress theory is also employed to consider the size effect on the matrix material of micro plate. In addition, it is assumed that the micro wires are arranged in FG forms in the direction of the thickness of the micro plate. Using the return mapping algorithm and nonlinear finite element method, the governing equations of motion, are solved. In the results section, the study of parameters such as size effects, different boundary conditions, taking into account nonlinear strain field, diameter change and type of arrangement of micro SMA wires, length scale factor and thickness of micro plate, have been implemented. To evaluate the validity of the present work, some of the results are compared with the articles available in the literature. New results show that the bigger diameter of the micro SMA wires (considering the total volume fraction constant) and the smaller length scale factor, the higher damping ratio of the micro plate is obtained. Also, the vibration damping ratio increases when more micro SMA wires are arranged in form.

Effect of Martensitic Transformation and Grain Misorientation on Surface Roughening Behavior of Stainless Steel Thin Foils

The surface roughening (Ra), martensitic phase transformation (MPT), and grain misorientation (GMO) behavior of stainless steel 304 and 316 in various grain sizes (Dg) were studied experimentally, including five cycles of sequential uniaxial tensile stress testing and Scanning Electron Microscope-Electron Back Scattered Diffraction (SEM-EBSD) investigation. The MPT and GMO characteristics were sequentially investigated using tensile testing and SEM-EBSD analysis. The correlation between MPT, GMO, martensitic volume fraction (Mf), and Ra behavior were investigated. The experimental results showed that increasing the total strain from 5.0% to 25.0% increased the MPT, GMO, and Mf, which were transformed from the metastable austenitic phase in stainless steel (SUS) 304. The increasing total strain increased Ra for all kinds of Dg. Furthermore, SUS 304 and SUS 316 were used to compare the roughening mechanism. The MPT was very high and spread uniformly in fine grain of SUS 304 thin foil, but the MPT was low and not uniform in coarse grain of SUS 304 thin foil. There was no MPT in SUS 316 thin foil, both in coarse and fine grain. The GMO in fine grains, both in SUS 304 and SUS 316 thin foils, spread uniformly. The GMO in coarse grains, both in SUS 304 and SUS 316 thin foils, did not spread uniformly. Surface roughness increased higher in coarse grain than fine grain for both of SUS 304 and SUS 316 thin foil. SUS 304 increased higher than SUS 316 thin foil. The effect of inhomogeneous deformation due to the MPT is a more important factor than GMO in coarse grain.

Effect of microstructural constituents and morphological characteristics on low cycle fatigue behaviour of inter-critically annealed 20MnMoNi55 steel

The effect of varying microstructural parameters on the cyclic behaviour of dual-phase steels was studied on the basis of experimental and micromechanical finite-element simulated results. The initial bainitic morphology of as-received 20MnMoNi55 steel was transformed into ferrite and martensite through proper inter-critical heat treatment procedures. Strain-controlled low cycle fatigue tests were conducted at room temperature with different strain amplitudes at a specific strain rate of 10−3/s. The cyclic stress–strain curve, obtained through joining the peak stresses of hysteresis loops corresponding to different strain amplitude, shows an increase in strain hardening with an increase in volume fraction of martensite. Whereas the rate of cyclic softening, considering the decrease in stress amplitude with respect to elapsed cycles, increases with increasing strain amplitude. Inclusive of all affecting microstructural parameters, an original microstructure-based representative volume element associated with a crystal plasticity-based material model was adopted for conducting micromechanical finite-element simulation. In addition to several parameters associated with a crystal plasticity model, consideration of initial geometrically necessary dislocation density in constituent phases resulted in the accurate prediction of a hysteresis loop at low strain amplitude as compared with the experimental results. A variation of stress triaxiality built up in ferrite matrix with martensite fraction along with deformation inhomogeneity between ferrite and martensite was also observed through a strain partitioning phenomenon obtained from finite-element simulated results.

Influence of prior deformation temperature on strain induced martensite formation and its effect on the tensile strengthening behaviour of type 304 SS studied by XRDLPA

Type 304 stainless steel is a metastable austenitic stainless steel that undergoes strain induced transformation from austenite to α′ martensite during deformation at room temperature. Role of prior deformation, by rolling at room temperature and at 200 °C (a temperature at which the strain induced martensitic transformation does not occur), on the subsequent room temperature tensile deformation behaviour of the austenite phase is investigated. The changes in dislocation density of the parent phase and the volume fraction of the martensite formed due to deformation were estimated by X-ray diffraction line profile analysis of data obtained from Beam Line - 12 of the Indus 2 synchrotron. The contrast caused by dislocations in the austenite phase has been addressed using the modified Williamson-Hall method. The character of dislocations changes from screw to edge above a critical equivalent strain of ~0.14. The influence of martensite formation on the increase in dislocation density in the austenite phase is confirmed from XRDLPA. An alternative approach to determine dislocation density is proposed which is independent of elastic constants of the material and is found to correlate well with the values determined by the Williamson-Smallman approach. The results obtained from XRDLPA are corroborated with EBSD analysis. It is also seen that the composite strength of the steel, which has undergone different levels of deformation, is related to the changes in dislocation density of austenite and volume fraction of martensite based on Taylor's equation enabling correlation of structure-property.

A Crystal Plasticity Simulation on Strain-Induced Martensitic Transformation in Crystalline TRIP Steel by Coupling with Cellular Automata

In transformation-induced plasticity (TRIP) steel, the strain-induced martensitic transformation (SIMT) has a close relationship with the shear band formation. At a small length scale such as that of a crystal, the explicit analysis of the shear band structure with the formed microstructure is quite important for an adequate understanding of the SIMT. Here, a study on the microstructures formed by SIMT, related to shear band formation in both single and polycrystal TRIP steels, is presented. The constitutive equation for single crystal TRIP steel considering the transformation strain on each variant system is derived based on a rate-dependent crystal plasticity theory. To express the martensitic transformation, the cellular automata approach, including a transformation criterion acting as a local rule, is introduced. Numerical simulation is conducted with patterning processes of the martensitic phase at an infinite medium under the plane strain tension. It is found that the similar distributions of the plastic strain and the martensitic phase are dependent on the initial crystal orientation and appear as the shear band structures. In addition, the sizes of embryo and cell strongly influence the shear band formation and the martensitic volume fraction of crystal TRIP steel.

A micromechanics-based constitutive model for nanocrystalline shape memory alloys incorporating grain size effects

A micromechanics-based model is developed to capture the grain-size dependent superelasticity of nanocrystalline shape memory alloys (SMAs). Grain-size effects are incorporated in the proposed model through definition of dissipative length scale and energetic length scale parameters. In this paper, nanocrystalline SMAs are considered as two-phase composites consisting of the grain-core phase and the grain-boundary phase. Based on the Gibbs free energy including the spatial gradient of the martensite volume fraction, a new transformation function determining the evolution law for transformation strain is derived. Using micromechanical averaging techniques, the grain-size-dependent superelastic behavior of nanocrystalline SMAs can be described. The internal length scales are calibrated using experimental results from published literature. In addition, model validation is performed by comparing the model predictions with the corresponding experimental data on nanostructured NiTi polycrystalline SMA. Finally, effects of the internal length scales on the critical stresses for forward and reverse transformations, the hysteresis loop area (transformation dissipation energy), and the strain hardening are investigated.

Controllable Martensite Transformation and Strain-Controlled Fatigue Behavior of a Gradient Nanostructured Austenite Stainless Steel.

Gradient nanostructured (GNS) surface layer with a controllable martensite fraction has been synthesized on 316L austenitic stainless steel by means of surface mechanical rolling treatment (SMRT) with temperature being controlled. The mean grain size is in the nanometer scale in the near-surface layer and increases gradually with depth. In addition, the volume fraction of martensite decreases from ~85% to 0 in the near-surface layer while the SMRT temperature increases from room temperature to 175 °C. Fatigue experiments showed that the strain-controlled fatigue properties of the GNS samples are significantly enhanced at total strain amplitudes ≥0.5%, especially in those with a dual-phase surface layer of austenite and pre-formed martensite. Analyses on fatigue mechanisms illustrated that the GNS surface layer enhances the strength-ductility synergy and suppresses the formation of surface fatigue defects during fatigue. In addition, the dual-phase structure promotes the formation of martensite and stacking faults, further enhancing fatigue properties at high strain amplitudes.

Examining the unloading behavior of dual-phase steels by means of microstructure simulations

Ferritic–martensitic dual-phase (DP) steels exhibit a pronounced nonlinear unloading behavior, which is subjected to strong variations and depends on the complex interaction of parameters of the sheet metal material production process and the resulting heterogeneous microstructure. The knowledge of the unloading behavior in dependence of the governing parameters and their underlying mechanisms play a crucial role in sheet metal forming of high strength dual-phase steels.To analyze the influence of individual parameters on the unloading behavior of dual-phase steels, computational studies on the microstructure level were carried out based on the finite element method. The investigated parameters included microstructural parameters, unloading rate and thermo-mechanical deformation history caused by sheet production. In the course of the simulations, numerous different periodic volume elements were uniaxially loaded and unloaded.The computational results demonstrate that residual stresses of type II in the microstructure cannot fully explain the nonlinear unloading behavior of the steels. The reversible slip of dislocations in ferrite also plays an important role. Of all parameters examined, the martensite volume fraction and the phase strength contrast have the largest impact on the unloading behavior. Furthermore, the distribution of martensite in the microstructure significantly affects the unloading behavior, as well as residual stresses and a plastic pre-deformation both caused by the sheet production.

A mean-field homogenization approach to predict fracture in as-quenched microstructures of Ductibor® 500-AS steel: characterization and modelling

Ductibor® 500-AS is a hot-stamping steel that has been designed to introduce local ductile regions within hot-stamped tailor-welded blanks (TWBs) used for energy-absorbing sections of automotive structures. This study investigates the flow and fracture behavior of a range of the microstructures of this alloy, corresponding to mostly ferritic (~96% ferrite plus 4% martensite), intermediate ferritic + martensitic (~57% ferrite plus 43% martensite), and mostly martensitic (~10% ferrite plus 90% martensite), obtained by applying various quench rates after austenitization. A series of mechanical tests in various stress states, ranging from simple shear to biaxial tension, was performed to characterize fracture for the developed microstructures. A mean-field homogenization (MFH) technique was then used to predict the flow and fracture response as a function of the microstructure. An MFH scheme designated as the interpolative Samadian-Butcher-Worswick 1 (INSBW1) within the first-order secant-based linearization method was considered to predict the macroscopic hardening behavior of the ferritic-martensitic microstructures. In the MFH modelling, the flow response of the ferritic and martensitic phases was modelled based on a dislocation-based hardening model, taking into account the chemical composition, carbon partitioning between phases, and dislocation generation and annihilation. Damage accumulation and the onset of fracture were predicted using a phenomenological damage indicator defined within each constituent phase given their calculated fracture loci and instantaneous stress and strain states. The experimental results showed that the mostly-martensitic microstructure had the lowest ductility and highest strength, and ductility and strength increased and decreased, respectively, as the martensite volume fraction in the microstructure decreased. The predicted flow curves and fracture strains as well as the fracture-limit curves for all of the microstructures agreed well with the measured data and interpolated modified Mohr-Coulomb (MMC) fracture loci.

Effect of Martensite Volume Fraction on Oxidative and Adhesive Wear.

It is generally known that microstructure can considerably affect the tribological behavior of non-lubricated rubbing. However, there is still a lack of awareness about the effect of microstructure on oxidative wear. The present study focused on the effect of martensite volume fraction (MVF) on oxidative wear by using 25CD4 dual-phase steel. Dry friction tests were performed on a ball-on-flat tribometer with a normal load of 15 N and a mean sliding velocity of 0.013 m/s. Friction coefficient and wear rate increase with the increasing MVF. SEM observation and EDXS analyses of the wear scars showed that the oxidation increases with decreasing MVF. For lower MVF, the main wear mechanism is mild oxidative wear. For higher MVF, severe adhesion is predominant as a wear mechanism. The size of the debris decreases with decreasing MVF.

Aging Behavior of Intercritically Quenched Ductile Iron

Although extensive aging and strain aging (bake hardening, BH) studies have been carried out on dual-phase steels, the aging behavior of the dual matrix structure (DMS) ductile iron (DI), as a potential way to improve its mechanical properties, has not been addressed until now. This research was designed to study the aging behavior of DI with a ferrite-martensite matrix structure. DMS-DI with a martensite volume fraction of 30% was produced by intercritical austenitizing at 785 °C followed by quenching in water to room temperature. Aging treatments were carried out without pre-straining at aging temperatures of 140, 170, and 220 °C for 2–10,000 min. DMS-DI was investigated by light optical microscopy (LOM) for unaged samples and scanning electron microscopy (SEM) for selected samples after aging treatments. The effect of aging conditions on the mechanical properties were investigated. Microhardness measurements for ferrite and martensite were also examined as a function of aging conditions. The increase in yield strength due to aging was determined. The results indicate that the aging conditions have a small effect on the ultimate tensile strength UTS. It is shown that the yield strength increased to a maximum value of 45 MPa (~11% increase) after aging for particular time, which is found to be dependent on the aging temperature. The peak aging response is followed by a decrease in yield strength, which is observed to be attributed to martensite tempering as confirmed by microhardness measurements.

Martensite formation during heating from cryogenic temperatures – A phase-field study

A 3D elastoplastic phase-field model is used to study the effect of isochronal heating on martensitic transformation in stainless steel quenched to cryogenic temperature. The results show that the slower the heating, the larger is the martensite volume fraction developed on heating. The simulated microstructures show that the transformation is driven by autocatalysis during the early stages and by coarsening of existing martensite units during later stages of the transformation. The internal stresses are mainly relaxed by autocatalysis during the initial stages of the transformation, whereas they are relaxed by plastic deformation during the later stages of the transformation. The temperature for attaining a certain martensite fraction increases with increasing heating rate, which is consistent with a thermally activated transformation. Kissinger-like analysis of the simulated transformation curves provides an activation energy of 11.9 kJ/mol.

Low-carbon cast microalloyed steel intercritically heat-treated at different temperatures: microstructure and mechanical properties

In this study, dual-phase (DP, ferrite + martensite) microstructures were obtained by performing intercritical heat treatments (IHT) at 750 and 800 °C followed by quenching. Decreasing the IHT temperature from 800 to 750 °C leads to: (i) a decrease in the volume fraction of austenite (martensite after quenching) from 0.68 to 0.36; (ii) ~ 100 °C decrease in martensite start temperature (Ms), mainly due to the higher carbon content of austenite and its smaller grains at 750 °C; (iii) a reduction in the block size of martensite from 1.9 to 1.2 μm as measured by EBSD. Having a higher carbon content and a finer block size, the localized microhardness of martensite islands increases from 380 HV (800 °C) to 504 HV (750 °C). Moreover, despite the different volume fractions of martensite obtained in DP microstructures, the hardness of the steels remained unchanged by changing the IHT temperature (~ 234 to 238 HV). Applying lower IHT temperature (lower fraction of martensite), the impact energy even decreased from 12 to 9 J due to the brittleness of the martensite phase. The results of the tensile tests indicate that by increasing the IHT temperature, the yield and ultimate tensile strengths of the DP steel increase from 493 to 770 MPa, and from 908 to 1080 MPa, respectively, while the total elongation decreases from 9.8 to 4.5%. In contrast to the normalized sample, formation of martensite in the DP steels could eliminate the yield point phenomenon in the tensile curves, as it generates free dislocations in adjacent ferrite.