Magneto-optical Kerr Effect Magnetometer Research Articles

Magneto-optical Kerr effect (MOKE) and magnetic force microscopy (MFM) studies on Cr/Ni nanodot arrays deposited using innovative nano-stencil method

Nanodot arrays of Nickel (Ni) on Chromium (Cr), [Cr in two forms i. e. (Cr dot) and Cr (layer)] were fabricated by electron beam evaporation technique using nano-stencil. The deposition of a periodic dot pattern was confirmed through atomic force microscopy (AFM) imaging. The nano magnetic properties of the Cr/Ni nanodot arrays were probed using both Magnetic Force Microscopy (MFM) and Magneto-Optical Kerr Effect (MOKE) magnetometer. MOKE measurements unveiled saturated hysteresis with the exchange bias effect for the in-plane configuration and a minor hysteresis loop for the out-of-plane configuration in the Cr/Ni nanodot system. The experimental results were found to be in good agreement with the theoretical Stoner-Wohlfarth (SW) model. Additionally, the exchange bias effect was also observed in the Cr (thin film)/Ni (nanodot) system for both the in-plane and out-of-plane configurations, showing the dominating behavior of the Cr layer over the Ni dots due to its continuous layer and higher thickness. The observation of exchange bias properties was also verified through MFM measurements conducted with both positive and negative in-plane magnetic fields. Hence, this straightforward nano-stencil method holds significant promise for the streamlined production of patterned AFM/FM arrays enabling the comprehensive study of exchange bias phenomena. The magnetic properties of the Cr/Ni structure can be manipulated by depositing Cr either in nanodot form or in continuous layer form.

Measurement of Kerr rotation and ellipticity in magnetic thin films by MOKE magnetometry

When polarized light is incident on a magnetic material, the magneto-optical Kerr effect (MOKE) rotates the polarization and induces ellipticity in the reflected light, which allows the magnetization direction to be probed optically. The Kerr rotation and ellipticity determine the magnitude of the effect and are usually measured using dedicated ellipsometers. Here, we demonstrate a simple method for extracting Kerr rotation and ellipticity in magnetic thin films using a conventional MOKE magnetometer consisting of two polarizers and a quarter waveplate. Using this technique, we report the longitudinal Kerr angle of BiYIG, GdCo, and TbCo. We additionally observe a linear decrease in polar complex Kerr angle magnitude in 3 nm GdCo films as the atomic fraction of Gd is increased.

Studies on the structural and magnetic properties of PMMA/Ni nanocomposite system prepared by embedding Ni nanoparticles in the PMMA films

PMMA/Ni nanocomposite films have been prepared by embedding Ni nanoparticles and maintaining their different thickness (5–50 nm) in PMMA (polymethylmethacrylate) film matrix by using ion beam sputtering (IBS) technique. Grazing incidence x-ray diffraction (GIXRD) results reveal Ni is present in metallic form in the FCC phase. X-ray reflectivity (XRR) is used to measure the nominal thickness of the Ni nanoparticle layer. Surface morphology was studied using atomic force microscopes (AFM). SXAS (soft x-ray absorption spectroscopy) studies on PMMA/Ni nanocomposites were done using synchrotron radiation to understand the electronic structure of these films which reveals that Ni is present in metallic state confirming that PMMA as host matrix protects the magnetic Ni nanoparticles from external oxidation. The magneto-optical Kerr effect (MOKE) magnetometer and MOKE microscope were employed to study the magnetic properties and simultaneously record the real time evolution of magnetic domains at 0°, 45°, and 90° azimuthal angles. All films show soft ferromagnetic behaviour and all the films show isotropic behaviour except one with Ni nanoparticle layer thickness of 40 nm. MOKE micrographs witness the gradual growth of magnetic domains with increase in thickness of Ni nanoparticle layer. These PMMA/Ni nanocomposite films may be viewed as potential candidate for futuristic functional material.

Structural and Magnetic Properties of Ni Nanoparticles Embedded in Vinyl Polymer Nanocomposite Films

Ni nanoparticles layer of nominal thickness in the range of 5–40[Formula: see text]nm were deposited on polyvinyl alcohol (PVA) film by using the ion beam sputtering (IBS) technique. PVA films were made on a quartz substrate by the solution casting technique. Grazing incidence X-ray diffraction (GIXRD) results reveal Ni is present in a metallic form in the FCC phase. AFM shows that roughness increases with increase in thickness of Ni layer and corresponding MFM images of magnetic domains were recorded. Soft X-ray absorption spectroscopy (SXAS) studies on the PVA/Ni nanocomposites films were recorded using synchrotron radiation. This study is used to study the electronic structure of the as-prepared nanocomposite films and reveals that Ni nanoparticles are present in their metallic form. Magnetic properties were measured using the magneto-optical Kerr effect (MOKE) magnetometer and the films were found to be magnetically soft with higher value of coercivity at lower thickness of Ni nanoparticles layer. The results of magnetic studies are discussed in light of the microstructure and morphological features of PVA/Ni nanocomposite films. The PVA/Ni nanocomposites showed interesting anisotropic magnetic behavior; thus the investigative results may be useful for the development of futuristic flexible functional magnetic material system.

Magnetic state switching in FeGa microstructures

This work demonstrates that magnetoelectric composite heterostructures can be designed at the length scale of 10 µms that can be switched from a magnetized state to a vortex state, effectively switching the magnetization off, using electric field induced strain. This was accomplished using thin film magnetoelectric heterostructures of Fe81.4Ga18.6 on a single crystal (011) [Pb(Mg1/3Nb2/3)O3]0.68-[PbTiO3]0.32 (PMN-32PT) ferroelectric substrate. The heterostructures were tripped from a multi-domain magnetized state to a flux closure vortex state using voltage induced strain in a piezoelectric substrate. FeGa heterostructures were deposited on a Si-substrate for superconducting quantum interference device magnetometry characterization of the magnetic properties. The magnetoelectric coupling of a FeGa continuous film on PMN-32PT was characterized using a magneto optical Kerr effect magnetometer with bi-axial strain gauges, and magnetic multi-domain heterostructures were imaged using x-ray magnetic circular dichroism—photoemission electron microscopy during the transition to the vortex state. The domain structures were modelled using MuMax3, a micromagnetics code, and compared with observations. The results provide considerable insight into designing magnetoelectric heterostructures that can be switched from an ‘on’ state to an ‘off’ state using electric field induced strain.

A UHV MOKE magnetometer complementing XMCD-PEEM at the Elettra Synchrotron

We report on a custom-built UHV-compatible Magneto-Optical Kerr Effect (MOKE) magnetometer for applications in surface and materials sciences, operating in tandem with the PhotoEmission Electron Microscope (PEEM) endstation at the Nanospectroscopy beamline of the Elettra synchrotron. The magnetometer features a liquid-nitrogen-cooled electromagnet that is fully compatible with UHV operation and produces magnetic fields up to about 140 mT at the sample. Longitudinal and polar MOKE measurement geometries are realized. The magneto-optical detection is based on polarization analysis using a photoelastic modulator. The sample manipulation system is fully compatible with that of the PEEM, making it possible to exchange samples with the beamline endstation, where complementary X-ray imaging and spectroscopy techniques are available. The magnetometer performance is illustrated by experiments on cobalt ultra-thin films, demonstrating close to monolayer sensitivity. The advantages of combining in situ growth, X-ray Magnetic Circular Dichroism imaging (XMCD-PEEM) and MOKE magnetometry into a versatile multitechnique facility are highlighted.

Investigating the Super Paramagnetic Limits of Ferromagnetic Nanowires

Highly sensitive focused magneto optical Kerr effect magnetometer (MOKE) has been used to explore the nanoscale limit of state of the art electron beam lithography (EBL) patterned permalloy (NiFe) nanowires. The nanowires are 20 µm long arranged in 20 µm × 20 µm arrays. Permalloy of different thicknesses, which includes 10, 8, 6, 4 and 3.5 nm were deposited on 5 different samples containing these arrays. Results from 10 nm thick permalloy nanowires shows superparamagnetic transition at 85 ± 5 nm wire width. For 6 nm thick array, superparamagnetic transition occurs at 125 ± 25 nm. We therefore show that with 10 nm thickness, instead of 6 nm thickness, more miniaturisation of nanowire width can be achieved before the onset of superparamagnetism. This may be seen as very efficient in achieving increased storage density in memory devices.

Advanced MOKE magnetometry in wide-field Kerr-microscopy

The measurement of MOKE (Magneto-Optical Kerr Effect) magnetization loops in a wide-field Kerr microscope offers the advantage that the relevant domain images along the loop can be readily recorded. As the microscope's objective lens is exposed to the magnetic field, the loops are usually strongly distorted by non-linear Faraday rotations of the polarized light that occur in the objective lens and that are superimposed to the MOKE signal. In this paper, an experimental method, based on a motorized analyzer, is introduced which allows to compensate the Faraday contributions, thus leading to pure MOKE loops. A wide field Kerr microscope, equipped with this technology, works well as a laser-based MOKE magnetometer, additionally offering domain images and thus providing the basis for loop interpretation.

Direct observation of temperature-driven magnetic symmetry transitions by vectorial resolved MOKE magnetometry

Angle- and temperature-dependent vectorial magnetometry measurements are necessary to disentangle the effective magnetic symmetry in magnetic nanostructures. Here we present a detailed study on an Fe(1 0 0) thin film system with competing collinear biaxial (four-fold symmetry) and uniaxial (two-fold) magnetic anisotropies, carried out with our recently developed full angular/broad temperature range/vectorial-resolved magneto-optical Kerr effect magnetometer, named TRISTAN. The data give direct views on the angular and temperature dependence of the magnetization reversal pathways, from which characteristic axes, remanences, critical fields, domain wall types, and effective magnetic symmetry are obtained. In particular, although the remanence shows four-fold angular symmetry for all investigated temperatures (15 K–400 K), the critical fields show strong temperature and angular dependencies and the reversal mechanism changes for specific angles at a given (angle-dependent) critical temperature, showing signatures of an additional collinear two-fold symmetry. This symmetry-breaking is more relevant as temperature increases to room temperature. It originates from the competition between two anisotropy contributions with different symmetry and temperature evolution. The results highlight the importance of combining temperature and angular studies, and the need to look at different magnetic parameters to unravel the underlying magnetic symmetries and temperature evolutions of the symmetry-breaking effects in magnetic nanostructures.

Dynamic dependence to domain wall propagation through artificial spin ice

Domain wall propagation dynamics have been studied in nanostructured artificial kagome spin ice structures. A stripline circuit has been used to provide localised pulsed magnetic fields within the artificial spin ice structure. This provides control of the system through electrically assisted domain wall nucleation events. Synchronisation of the pulsed fields with additional global magnetic fields and the use of a focussed magneto-optical Kerr effect magnetometer allows our experiments to probe the domain wall transit through an extended ASI structure. We find that the propagation distance depends on the driving field revealing field driven properties of domain walls below their intrinsic nucleation field.

The effect of annealing temperature on the magnetic anisotropy in Co ultrathin film on MgO(001) substrate

Co epitaxial thin films with 2.5nm thickness were prepared on single-crystal MgO(001) substrates and annealed at different temperatures. The contribution of each interface of the MgO/Co/Cu trilayer to the in-plane magnetic anisotropy (IMA) was studied by changing interfacial coupling through annealing. The structure was measured by low energy electron diffraction (LEED), and the magnetic properties were measured using the anisotropic magnetoresistance (AMR) measurements and the longitudinal Magneto-optical Kerr effect magnetometer (MOKE). We found that the magnetic anisotropy of the as-deposited one shows superposition of a two-fold symmetry with a weak four-fold contribution caused by the stress of the interface between Co/Cu, which is along the easy axis [-110]. After annealing at 200°C, the symmetry of magnetic anisotropy was changed from uniaxial magnetic anisotropy (UMA) into four-fold symmetry due to the significant increasing of four-fold magnetocrystalline anisotropy. When the films were annealed above 300°C, the damage of the MgO/Co interface additionally decreased the IMA to isotropy. Meanwhile, the coercivity raised from 45Oe (without annealing) to 1200Oe (annealed at 400°C) along the easy axis direction. Our experimental results prove that the Co/Cu interface and the MgO/Co interface play an essential role in manipulating the four-fold and the UMA in the system.

Influence of Ar Pressure on the Magnetic Properties of Amorphous FeGaSiB Thin Films

Magnetostrictive amorphous FeSiB and FeGaSiB thin films thickness 50 nm have been grown by the co-sputtering-evaporation technique with a range of Ar pressure (4– $8~\mu $ bar) to control the Ga percentage within the films and study their effect on the magnetic, structural, and magnetostriction properties. By X-ray diffraction, it was found that all the films had an amorphous structure and the only peaks were present for Si substrate. Using a magneto-optical Kerr effect magnetometer, it was found that, for the FeSiB films, the anisotropy field $(H_{k}$ ) increased slowly as the pressure increased, while for the FeGaSiB films, the saturation field $(H_{s}) \approx 4000$ A/m for all pressures. For both the film sets, the coercive field $(H_{c})$ was less than 800 A/m. The magnetostriction constants $(\lambda _{s})$ of the FeSiB thin films increased with increasing pressure. While for the FeGaSiB films, the magnetostriction constant decreased with increasing the sputtering gas pressure, with the maximum $\lambda _{s} = 11.4$ ppm, at the lowest pressure $4~\mu $ bar. Thus, it was determined that the addition of Ga atoms reduced the intrinsic stress within the films, while maintaining the amorphous morphology.

Stochastic domain wall depinning in permalloy nanowires with various types of notches

Stochastic phenomena in magnetic nanowires based on domain wall (DW) motion is scientifically important thus to understand and control such behaviors are very meaningful. Here we report on the investigation of pinning and depinning of DWs in permalloy nanowires with six types of longitudinally asymmetric notches using focused magneto-optic Kerr effect (FMOKE) magnetometer and magnetic force microscopy (MFM). The hysteresis loops obtained by FMOKE indicate the generation of one or two distinct depinning fields by creating one notch close to the edge of the nanowires, in comparison multiple depinning processes occur in the nanowires with two identical notches symmetrically placed along the transverse direction, indicating more remarkable stochastic DW depinning phenomena. The MFM images verify the existence of DW in each type of nanowires and the DW sizes in the latter kind of nanowires are generally larger than those in the former ones. These observations can be explained by considering the thermal perturbation and edge or surface roughness effects in nanowires.

Influence of the phenomena occurring at the interface between L10-ordered-FePt and Fe on the coercivity behavior

L10-ordered FePt/Fe thin bi-layers were grown using a molecular beam epitaxy onto (100)-MgO substrates changing the soft Fe layer thickness. The study of the intermixing phenomena occurring at the hard/soft interfaces was carried out using surface Mossbauer spectroscopy. The magnetic properties of the samples were analyzed with a magneto-optical Kerr effect magnetometer. The surface morphology and the magnetic domains were analyzed with an UHV atomic and magnetic force microscopy in tapping and lift mode respectively.The present work clearly demonstrates that the degree of interface intermixing and reactions is the responsible for the coercivity behavior in exchange-spring magnets.

Depinning of domain walls in permalloy nanowires with asymmetric notches.

Effective control of the domain wall (DW) motion along the magnetic nanowires is of great importance for fundamental research and potential application in spintronic devices. In this work, a series of permalloy nanowires with an asymmetric notch in the middle were fabricated with only varying the width (d) of the right arm from 200 nm to 1000 nm. The detailed pinning and depinning processes of DWs in these nanowires have been studied by using focused magneto-optic Kerr effect (FMOKE) magnetometer, magnetic force microscopy (MFM) and micromagnetic simulation. The experimental results unambiguously exhibit the presence of a DW pinned at the notch in a typical sample with d equal to 500 nm. At a certain range of 200 nm < d < 500 nm, both the experimental and simulated results show that the DW can maintain or change its chirality randomly during passing through the notch, resulting in two DW depinning fields. Those two depinning fields have opposite d dependences, which may be originated from different potential well/barrier generated by the asymmetric notch with varying d.

Assemblies of magnetite nanoparticles extracted from magnetotactic bacteria: A magnetic study

Self-assembly has emerged as a suitable technique for tuning the properties of nanoparticles. In this work, we report the self-assembly of magnetosomes assisted by an external magnetic field. The magnetosomes are magnetite nanoparticles biomineralized by magnetotactic bacteria Magnetospirillum gryphiswaldense. These nanoparticles present truncated cubo-octahedral morphology with a mean diameter of ≈36 nm and are surrounded by a lipid bilayer membrane with a thickness ≈2–4 nm. The use of the appropriate preparation conditions, such as initial colloidal concentration and magnetic fields applied during deposition allowed us to obtain very reproducible self-assembled 2D patterns. Homogeneous ensembles of magnetosomes onto silicon and carbon surfaces are composed of elongated structures in the form of wide chains that cover a large area of the substrates. Transmission electron microscopy image and off-axis electron holography showed the map of the stray magnetic fields produced by these assemblies. The induced magnetic anisotropy was analyzed by measuring the hysteresis loops of the assemblies at different angles in a magneto-optical Kerr effect magnetometer. The evolution of the coercive field and remanence verified the presence of well-defined patterns. The experimental results were analyzed on the based of a biaxial model.

Investigations of the polymer/magnetic interface of organic spin-valves

This work investigates the top interface of an organic spin-valve, to determine the interactions between the polymer and top magnetic electrode. The polymers studied are regio-regular poly(3-hexylthiophene) (RR-P3HT) and poly(2,5-bis(3-hexadecylthiophen-2-yl)thieno[3,2-b]thiophene (PBTTT) and the magnetic top electrodes are NiFe and Fe. X-ray photoelectron spectroscopy (XPS) is used to determine the bonding at the interface, along with the extent of how oxidised the magnetic layers are, while atomic force microscopy (AFM) is used to determine the surface roughness. A magneto-optic Kerr effect (MOKE) magnetometer is used to study the magnetic properties of the top electrode. It is shown that at the organic–magnetic interface the magnetic atoms interact with the polymer, as metallic–sulphide and metallic-carbide species are present at the interface. It is also shown that the structure of the polymer influences the anisotropy of the magnetic electrode, such that the magnetic electrodes grown on RR-P3HT have uniaxial anisotropy, while those grown on PBTTT are isotropic.

Ultrafast dynamics and THz oscillation in [Co/Pd]8 multilayers

Abstract We report the experimental observation of ultrafast demagnetization associated with a significant terahertz (THz) emission in [Co/Pd] 8 multilayers (MLs) with strong perpendicular magnetic anisotropy (PMA) by using a time-resolved magneto-optical Kerr effect (TR-MOKE) magnetometer. The THz emission is associated with subsequent remagnetization which is coupled with a collective picosecond magnetization dynamics and generation of acoustic waves in these multilayers. The demagnetization time increases slightly with decreasing Co layer thickness, while no such clear trend is observed in remagnetization timescales. The anisotropy field and corresponding precession frequency show systematic increase with the decrease of Co layer thickness. However, the acoustic wave frequencies remain unchanged with Co layer thickness. The inverse of the full width at half maximum of the THz radiation varies systematically with the anisotropy field, whereas the THz peak frequency remains almost constant at around 2 THz. The origin of THz radiation is explained in terms of excitation of THz transient phonons.

Tuning the magnetic anisotropy of CoFeB grown on flexible substrates**Project supported by the National Basic Research Program of China (Grant Nos. 2011CB922201 and 2015CB921401) and the National Natural Science Foundation of China (Grant Nos. 11174272, 11474272, 11274371, 51431009, and 61225021).

The magnetic properties of CoFeB thin films grown on flexible polyimide substrates were investigated using a magneto-optical Kerr effect magnetometer. In-plane uniaxial magnetic anisotropy was observed in the virgin state. The strain induced by bending the flexible substrate was applied on the sample to change the magnetic properties of CoFeB. The strain induced uniaxial magnetic anisotropy changed linearly with the deformation by about 8.41 × 1041 erg/cm3 at 1% of deformation. Our results prove the magnetic properties of CoFeB grown on flexible polyimide substrate can be tuned effectively by bending, which could be important for future flexible spintronics.

Vortex manipulation and chirality control in asymmetric bilayer nanomagnets

This paper presents a method of controlling the chirality of magnetic vortex in a permalloy nanodisk having a cobalt nanostripe at the top. Features of magnetization reversal of the disk + stripe nanostructure are investigated using the magneto-optical Kerr effect magnetometer and magnetic force microscope. Micromagnetic simulations reveal peculiarities in the vortex nucleation process and in trajectory of the vortex core under the impact of external magnetic fields.