Magnetic Resonance Imaging System Research Articles

Research on a portable shielding-free ultra-low field magnetic resonance imaging system

The portable light-weight magnetic resonance imaging system can be deployed in special occasions such as Intensive Care Unit (ICU) and ambulances, making it possible to implement bedside monitoring imaging systems, mobile stroke units and magnetic resonance platforms in remote areas. Compared with medium and high field imaging systems, ultra-low-field magnetic resonance imaging equipment utilizes light-weight permanent magnets, which are compact and easy to move. However, the image quality is highly susceptible to external electromagnetic interference without a shielded room and there are still many key technical problems in hardware design to be solved. In this paper, the system hardware design and environmental electromagnetic interference elimination algorithm were studied. Consequently, some research results were obtained and a prototype of portable shielding-free 50 mT magnetic resonance imaging system was built. The light-weight magnet and its uniformity, coil system and noise elimination algorithm and human brain imaging were verified. Finally, high-quality images of the healthy human brain were obtained. The results of this study would provide reference for the development and application of ultra-low-field magnetic resonance imaging technology.

Evaluation of the Performance of Commercial High Temperature Superconducting Tapes for Dynamo Flux Pump Applications

High Temperature Superconducting (HTS) dynamo flux pumps are a promising alternative to metal current leads for energization and the persistent current mode operation of high current DC superconducting magnet systems for applications in rotating machines, such as Magnetic Resonance Imaging (MRI) or fusion systems. The viability of the flux pump concept has been widely proven by laboratory experiments and research is now in progress for the design and optimization of flux pump devices for practical applications. It has been widely established that the dependence of the critical current density (Jc) on the temperature (T), the magnetic field magnitude (B), and the orientation (θ), has a substantial impact on the overall DC voltage obtained at the terminals, as well as on the current limit and the loss of the flux pump. Since HTS tapes produced by different manufacturers, they show different dependencies of Jc with the amplitude and the orientation of the magnetic field. They also give rise to different outputs when employed in flux pumps. In this paper, we evaluate and compare the performance of several commercial HTS tapes used for flux pumping purposes through numerical simulation. We also investigate the dependence of the flux pump ‘s performance on the operating temperatures. A 2D finite element numerical model is first developed and validated against experimental data at 77 K. Afterward, the same HTS dynamo apparatus used for validation is exploited for the comparison. The Jc(B,θ,T) and n(B,θ,T) relations, which characterize each different tape in the model, are reconstructed via artificial intelligence techniques based on the open-access database of the Robinson Research Institute. It is shown in the paper that certain tapes are more suitable than others for flux pump applications and that the best overall operating temperature is in the vicinity of 77 K.

3D phase-sensitive inversion recovery sequence for intracranial vertebrobasilar artery dissection

BackgroundT1-weighted 3D turbo spin echo (T1W-3D-TSE) sequences with variable refocusing flip angle are commonly used to diagnose intracranial vertebrobasilar artery dissection (iVAD). However, magnetic susceptibility artifacts of the cavernous sinus may cause loss of the basilar and vertebral arteries. This study investigated the effectiveness of a 3D phase-sensitive inversion recovery (3D-PSIR) sequence in reducing magnetic susceptibility artifacts in the cavernous sinus, and its imaging findings for iVAD. MethodsTwelve volunteers and eleven patients with iVAD were included. Magnetic resonance imaging (MRI) was performed using a 3.0-T MRI system. 3D-PSIR and T1W-3D-TSE sequences were used. Vessel wall defects and contrast-to-noise ratio (CNR) were evaluated. The MRI findings were visually evaluated. ResultsIn the 3D-PSIR images, one volunteer (8 %) had vessel wall defects, and five (42 %) had vessel wall defects (p = 0.046) in the T1W-3D-TSE images. CNR was higher in 3D-PSIR images for vessel wall-to-lumen, whereas it was higher in T1W-3D-TSE images for vessel wall-to-CSF (p < 0.001). Visual evaluation revealed similar MRI findings between the two sequences. ConclusionsThe 3D-PSIR sequence may be able to improve the vessel wall defects and achieve MRI findings comparable to those of the T1W-3D-TSE sequence in iVAD. The 3D-PSIR sequence can be a useful tool for the imaging-based diagnosis of iVAD.

Real-time MRI of the moving wrist at 0.55 tesla.

Magnetic resonance imaging (MRI) using 1.5T or 3.0T systems is routinely employed for assessing wrist pathology; however, due to off-resonance artifacts and high power deposition, these high-field systems have drawbacks for real-time (RT) imaging of the moving wrist. Recently, high-performance 0.55T MRI systems have become available. In this proof-of-concept study, we tested the hypothesis that RT-MRI during continuous, active, and uninterrupted wrist motion is feasible with a high-performance 0.55T system at temporal resolutions below 100 ms and that the resulting images provide visualization of tissues commonly interrogated for assessing dynamic wrist instability. Participants were scanned during uninterrupted wrist radial-ulnar deviation and clenched fist maneuvers. Resulting images (nominal temporal resolution of 12.7-164.6 ms per image) were assessed for image quality. Feasibility of static MRI to supplement RT-MRI acquisition was also tested. The RT images with temporal resolutions < 100 ms demonstrated low distortion and image artifacts, and higher reader assessment scores. Static MRI scans showed the ability to assess anatomical structures of interest in the wrist. RT-MRI of the wrist at a high temporal resolution, coupled with static MRI, is feasible with a high-performance 0.55T system, and may enable improved assessment of wrist dynamic dysfunction and instability. Real-time MRI of the moving wrist is feasible with high-performance 0.55T and may improve the evaluation of dynamic dysfunction of the wrist.

Comparison of Contrast-Enhanced 3D Imaging with 2D Imaging in the Evaluation of Perianal Fistula at 3T: A Prospective Observational Study.

Introduction Perianal fistula and its recurrence is a challenging entity for surgeons. It is a well-establi1shed fact that magnetic resonance imaging (MRI) findings influence surgical procedures and reduce the rate of recurrence. In this study, we assessed the contrast-enhanced (CE) three dimensional T1 sequences [sampling perfection with application optimized contrast using different flip angle evolution (SPACE) and volumetric interpolated breath-hold examination (VIBE)] in a 3T MRI system to evaluate perianal fistulas and compared them with two-dimensional (2D) sequences. Materials and Methods Forty-four patients (mean age, 38.8 ± 15.3 [standard deviation]; 32 males, 12 females) with perianal fistula were included in this prospective study. The patients underwent conventional noncontrast, 2D sequences, diffusion-weighted imaging, followed by postcontrast, 2D T1 images in both axial and coronal planes, and 3D sequences at 3T. Acquisition times were recorded for each sequence. Each postcontrast sequence was evaluated in terms of image quality, presence of artifacts, fistula type, presence of an abscess, visibility, and number of internal orifices. The surgical findings were considered the gold standard. The imaging findings were compared with the surgical findings. Results In all three sequences, the fistula type and abscess were identified correctly in all patients. The sensitivity value for identification of ramifications utilizing CE 3D T1 VIBE sequence, CE 3D T1 SPACE, and CE 2D T1 images was 100, 86, and 36%, respectively. The number of internal orifices was identified by the CE 3D T1 VIBE and CE 3D T1 SPACE sequences in 100 and 92% of patients, respectively. CE 2D T1 images correctly identified internal orifices in 80% of patients. The overall scan time for each 3D sequence was shorter than for the combined postcontrast 2D sequences. Conclusion CE 3D T1 SPACE and CE 3D T1 VIBE sequences outperformed conventional CE 2D sequences in the evaluation of perianal fistulas in terms of visibility and the number of internal orifices with a shorter scanning time. Among the 3D sequences, CE 3D T1 VIBE is slightly superior to CE 3D T1 SPACE sequence.

Simulation Study of Transient Eddy Current Effect in 3T Animal Gradient Coil

In the process of high-field magnetic resonance imaging (MRI), the eddy current modeling and simulation of the cold screen and metal parts are not highly accurate. To solve this problem, this paper uses the target field method to design a 3T animal gradient coil model. To get more realistic simulation results, a complex model including a gradient system, cryogenic vessel, cold screen, epoxy resin, and temperature holes was constructed. The model was refined using the finite element method, and the effects of eddy currents induced by the gradient coil on the cylindrical cryogenic container and cold screen in the superconducting magnetic resonance instrument under the state of multi-physical field coupling were simulated. The model effectively reflects the transient eddy current distributions on the cold screen and cryogenic vessel in the MRI system and their time-dependent temperature rise effects.

Gradient coil design with enhanced shielding constraint for a cryogen-free superconducting MRI system

The relatively fragile low-temperature stability of cryogen-free superconducting magnetic resonance imaging (MRI) magnets requires the careful management of exogenous heat sources. A strongly shielded gradient magnetic field is important for the optimal operation of cryogen-free MRI systems. In this study, we present an enhanced shielding method incorporating a regionalized stray field constraining strategy. By optimizing the constraint parameters, we could develop engineering-feasible gradient coil schemes without increasing system complexity but with the stray field intensity reduced by half. In real measurement in an integrated MRI system, the developed gradient assembly demonstrated good performance and supported to output images of excellent quality. Our findings suggested that the proposed method could potentially form a useful design paradigm for cryogen-free MRI magnets.

Resonating sub-wavelength metallic wires based pads for boosting signal-to-noise ratio of birdcage head coils at 1.5T MRI

Magnetic resonance imaging (MRI) is an increasingly popular non-invasive diagnostic imaging tool in modern healthcare. The signal-to-noise ratio (SNR) of MRI can be improved by locally enhancing radiofrequency (RF) magnetic field using metamaterials — without the need for stepping up static magnetic field strength. However, designing a thin and compact metamaterial-based structure for the most commonly used 1.5T MRI systems (operating at f0∼64MHz) remains highly challenging due to long vaccum wavelength λ0∼4.7m at resonance. The limited free space available inside MRI receive coil arrays (typically 10-20mm) restricts the practical usability of any bulky resonator (with dimensions in order of meters) inside commercial 1.5T MRI head transceiver-coils. In this paper, we design a thin and compact RF metamaterial-based pad comprising dual-layer wire-array resonators that fits in the available space and provides significant magnetic field enhancement at 1.5T MRI. The metamaterial-based pad provides the SNR enhancement by a factor of ∼19, on the surface of bio-model in contact with the pad, as compared to the case without pad while maintaining specific absorption rate well below the standard safety limit. We present an equivalent circuit approach combined with a transformer-based model to compute the SNR enhancement factor of metamaterial-based pad, which adequately explains the underlying physical mechanism of metamaterial’s magnetic resonance and closely estimates our numerical findings. We believe that, when integrated into the clinical 1.5T MRI systems, our proposed metamaterial-based pad can help improve the SNR of head MRI scans, resulting in either higher image quality or reduced scan time.

In vivo mapping of the deep and superficial white matter connectivity in the chimpanzee brain

Mapping the chimpanzee brain connectome and comparing it to that of humans is key to our understanding of similarities and differences in primate evolution that occurred after the split from their common ancestor around 6 million years ago. In contrast to studies on macaque species’ brains, fewer studies have specifically addressed the structural connectivity of the chimpanzee brain and its comparison with the human brain. Most comparative studies in the literature focus on the anatomy of the cortex and deep nuclei to evaluate how their morphology and asymmetry differ from that of the human brain, and some studies have emerged concerning the study of brain connectivity among humans, monkeys, and apes. In this work, we established a new white matter atlas of the deep and superficial white matter structural connectivity in chimpanzees. In vivo anatomical and diffusion-weighted magnetic resonance imaging (MRI) data were collected on a 3-Tesla MRI system from 39 chimpanzees. These datasets were subsequently processed using a novel fiber clustering pipeline adapted to the chimpanzee brain, enabling us to create two novel deep and superficial white matter connectivity atlases representative of the chimpanzee brain. These atlases provide the scientific community with an important and novel set of reference data for understanding the commonalities and differences in structural connectivity between the human and chimpanzee brains. We believe this study to be innovative both in its novel approach and in mapping the superficial white matter bundles in the chimpanzee brain, which will contribute to a better understanding of hominin brain evolution.

Prevalence and influencing factors for artifact development in breast MRI-derived maximum intensity projections.

Magnetic resonance imaging (MRI) provides high diagnostic sensitivity for breast cancer. However, MRI artifacts may impede the diagnostic assessment. This is particularly important when evaluating maximum intensity projections (MIPs), such as in abbreviated MRI (AB-MRI) protocols, because high image quality is desired as a result of fewer sequences being available to compensate for problems. To describe the prevalence of artifacts on dynamic contrast enhanced (DCE) MRI-derived MIPs and to investigate potentially associated attributes. For this institutional review board approved retrospective analysis, MIPs were generated from subtraction series and cropped to represent the left and right breasts as regions of interest. These images were labeled by three independent raters regarding the presence of MRI artifacts. MRI artifact prevalence and associations with patient characteristics and technical attributes were analyzed using descriptive statistics and generalized linear models (GLMMs). The study included 2524 examinations from 1794 patients (median age 50 years), performed on 1.5 and 3.0 Tesla MRI systems. Overall inter-rater agreement was kappa = 0.54. Prevalence of significant unilateral artifacts was 29.2% (736/2524), whereas bilateral artifacts were present in 37.8% (953/2524) of all examinations. According to the GLMM, artifacts were significantly positive associated with age (odds ratio [OR]=1.52) and magnetic field strength (OR=1.55), whereas a negative effect could be shown for body mass index (OR=0.95). MRI artifacts on DCE subtraction MIPs of the breast, as used in AB-MRI, are a relevant topic. Our results show that, besides the magnetic field strength, further associated attributes are patient age and body mass index, which can provide possible targets for artifact reduction.

Feasibility study of super-resolution deep learning-based reconstruction using k-space data in brain diffusion-weighted images.

The purpose of this study is to evaluate the influence of super-resolution deep learning-based reconstruction (SR-DLR), which utilizes k-space data, on the quality of images and the quantitation of the apparent diffusion coefficient (ADC) for diffusion-weighted images (DWI) in brain magnetic resonance imaging (MRI). A retrospective analysis was performed on 34 patients who had undergone DWI using a 3T MRI system with SR-DLR reconstruction based on k-space data in August 2022. DWI was reconstructed with SR-DLR (Matrix = 684 × 684) and without SR-DLR (Matrix = 228 × 228). Measurements were made of the signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR) in white matter (WM) and grey matter (GM), and the full width at half maximum (FWHM) of the septum pellucidum. Two radiologists assessed image noise, contrast, artifacts, blur, and the overall quality of three image types using a four-point scale. Quantitative and qualitative scores between images with and without SR-DLR were compared using the Wilcoxon signed-rank test. Images with SR-DLR showed significantly higher SNRs and CNRs than those without SR-DLR (p < 0.001). No statistically significant variances were found in the apparent diffusion coefficients (ADCs) in WM and GM between images with and without SR-DLR (ADC in WM, p = 0.945; ADC in GM, p = 0.235). Moreover, the FWHM without SR-DLR was notably lower compared to that with SR-DLR (p < 0.001). SR-DLR has the potential to augment the quality of DWI in DL MRI scans without significantly impacting ADC quantitation.

Impact of lateral meniscus injury detected by preoperative magnetic resonance imaging on midterm results after unicompartmental knee arthroplasty

BackgroundThe significance of lateral meniscus injury and its impact on success rates with medial unicompartmental knee arthroplasty (UKA) is still debated among scholars. This study aims to investigate whether preoperative magnetic resonance imaging (MRI) findings of lateral meniscus injury influence midterm outcomes following UKA. MethodsThis study recruited 104 patients who underwent medial mobile-bearing UKA. Based on the extent of lateral meniscus injury indicated by the preoperative MRI and Stoller's classification system, patients were divided into two groups: the normal group (grade 0), and the lateral meniscus injury group (grade 3). Further, preoperative demographic and clinical outcome data (Hospital for Special Surgery score, lateral knee pain, squatting, and knee extension ability) were compared at least 2 years postoperatively. ResultsNo statistically significant difference in knee function or clinical outcome was found between the normal group (n = 59) and the lateral meniscus injury group (n = 45). During the 39.2 months (range: 24–64 months), no patient required any reoperation or revision procedures. ConclusionIn summary, the presence of lateral meniscus injury as determined by preoperative MRI does not affect the midterm results after UKA. Without additional treatment for lateral meniscus injury, UKA can yield desired outcomes regardless of the presence of lateral meniscus injury on preoperative MRI.

Intratumoral heterogeneity after targeted therapy in murine cancer models with differing degrees of malignancy

IntroductionConventional morphologic and volumetric assessment of treatment response is not suitable for adequately assessing responses to targeted cancer therapy. The aim of this study was to evaluate changes in tumor composition after targeted therapy in murine models of breast cancer with differing degrees of malignancy via non-invasive magnetic resonance imaging (MRI). Materials and methodsMice bearing highly malignant 4T1 tumors or low malignant 67NR tumors were treated with either a combination of two immune checkpoint inhibitors (ICI, anti-PD1 and anti-CTLA-4) or the multi-tyrosine kinase inhibitor sorafenib, following experiments with macrophage-depleting clodronate-loaded liposomes and vessel-stabilizing angiopoietin-1. Mice were imaged on a 9.4 T small animal MRI system with a multiparametric (mp) protocol, comprising T1 and T2 mapping and diffusion-weighted imaging. Tumors were analyzed ex vivo with histology. Results and discussionsAll treatments led to an increase in non-viable areas, but therapy-induced intratumoral changes differed between the two tumor models and the different targeted treatments. While ICI treatment led to intratumoral hemorrhage, sorafenib treatment mainly induced intratumoral necrosis. Treated 4T1 tumors showed increasing and extensive areas of necrosis, in comparison to 67NR tumors with only small, but also increasing, necrotic areas. After either of the applied treatments, intratumoral heterogeneity, was increased in both tumor models, and confirmed ex vivo by histology. Apparent diffusion coefficient with subsequent histogram analysis proved to be the most sensitive MRI sequence. In conclusion, mp MRI enables to assess dedicated therapy-related intratumoral changes and may serve as a biomarker for treatment response assessment.

A Novel Portable, Mobile MRI: Comparison with an Established Low-Field Intraoperative MRI System.

Background MRI (magnetic resonance imaging) using low-magnet field strength has unique advantages for intraoperative use. We compared a novel, compact, portable MR imaging system to an established intraoperative 0.15 T system to assess potential utility in intracranial neurosurgery. Methods Brain images were acquired with a 0.15 T intraoperative MRI (iMRI) system and a 0.064 T portable MR system. Five healthy volunteers were scanned. Individual sequences were rated on a 5-point (1 to 5) scale for six categories: contrast, resolution, coverage, noise, artifacts, and geometry. Results Overall, the 0.064 T images (M = 3.4, SD = 0.1) had statistically higher ratings than the 0.15 T images (M = 2.4, SD = 0.2) ( p < 0.01). All comparable sequences (T1, T2, T2 FLAIR and SSFP) were rated significantly higher on the 0.064 T and were rated 1.2 points (SD = 0.3) higher than 0.15 T scanner, with the T2 fluid-attenuated inversion recovery (FLAIR) sequences showing the largest increment on the 0.064 T with an average rating difference of 1.5 points (SD = 0.2). Scanning time for the 0.064 T system obtained images more quickly and encompassed a larger field of view than the 0.15 T system. Conclusions A novel, portable 0.064 T self-shielding MRI system under ideal conditions provided images of comparable quality or better and faster acquisition times than those provided by the already well-established 0.15 T iMR system. These results suggest that the 0.064 T MRI has the potential to be adapted for intraoperative use for intracranial neurosurgery.

Investigating the effects of uniaxial pressure on the preparation of MgTiO3–CaTiO3 ceramic capacitors for MRI systems

AbstractToday's healthcare system relies on magnetic resonance imaging (MRI) for early diagnosis and treatment planning. For open MRI systems to achieve resolutions of about a hundred microns, a high voltage is required, as well as a specialized power supply. Negative–positive–zero (NP0) ceramic is selected for the fabrication of adjustable capacitors. Specifically, it stands for which is a classification based on the temperature coefficient of capacitance (TCC) of the ceramic material used in the capacitor. NP0 capacitors have a TCC of 0 ±30 ppm/°C, which means that their capacitance value does not change significantly with temperature and frequency. They are known for their stability and low losses, making them ideal for applications that require high accuracy and reliability, such as timing circuits for radio frequency (RF) applications. Here, MgTiO3–CaTiO3 ceramic is used to make an adjustable capacitor with desired properties for MRI systems. To enhance the dielectric properties of MgTiO3 ceramics, CaTiO3 was added in varying concentrations. After pressing and sintering, the resulting samples were tested using a vector network analyzer in the frequency range of 10–130 MHz. The adjustable capacitor fabricated using high co‐fired NP0 ceramic may have been used for MRI applications such as tuning circuits and matching networks, where precise capacitance values and low loss are critical. MRI systems with resonance frequencies of 128 MHz require trimmers with ceramic cores (VBreakdown = 3 kV @ 128 MHz, Cmin = 3 pF, CMax = 30 pF, and Cvariation step = 1.5 pF).

Noninvasive Magnetic Resonance Imaging Measures of Glymphatic System Activity.

The comprehension of the glymphatic system, a postulated mechanism responsible for the removal of interstitial solutes within the central nervous system (CNS), has witnessed substantial progress recently. While direct measurement techniques involving fluorescence and contrast agent tracers have demonstrated success in animal studies, their application in humans is invasive and presents challenges. Hence, exploring alternative noninvasive approaches that enable glymphatic research in humans is imperative. This review primarily focuses on several noninvasive magnetic resonance imaging (MRI) techniques, encompassing perivascular space (PVS) imaging, diffusion tensor image analysis along the PVS, arterial spin labeling, chemical exchange saturation transfer, and intravoxel incoherent motion. These methodologies provide valuable insights into the dynamics of interstitial fluid, water permeability across the blood-brain barrier, and cerebrospinal fluid flow within the cerebral parenchyma. Furthermore, the review elucidates the underlying concept and clinical applications of these noninvasive MRI techniques, highlighting their strengths and limitations. It addresses concerns about the relationship between glymphatic system activity and pathological alterations, emphasizing the necessity for further studies to establish correlations between noninvasive MRI measurements and pathological findings. Additionally, the challenges associated with conducting multisite studies, such as variability in MRI systems and acquisition parameters, are addressed, with a suggestion for the use of harmonization methods, such as the combined association test (COMBAT), to enhance standardization and statistical power. Current research gaps and future directions in noninvasive MRI techniques for assessing the glymphatic system are discussed, emphasizing the need for larger sample sizes, harmonization studies, and combined approaches. In conclusion, this review provides invaluable insights into the application of noninvasive MRI methods for monitoring glymphatic system activity in the CNS. It highlights their potential in advancing our understanding of the glymphatic system, facilitating clinical applications, and paving the way for future research endeavors in this field. EVIDENCE LEVEL: 3 TECHNICAL EFFICACY: Stage 5.

Magnetic resonance imaging pelvimetric measurements as predictors for emergent cesarean delivery in obstructed labor.

This study aimed to investigate the usefulness of various magnetic resonance imaging (MRI) pelvimetric parameters for predicting emergent cesarean delivery due to obstructed labor. This was a prospective observational study. MRI pelvimetry was performed in cases of a clinically suspected maternal narrow pelvis, maternal short stature, fetal overgrowth, and abnormal placental position. MRI pelvimetry was performed at 34.7±4.2 gestational weeks using a 1.5T MRI system. The pelvic inlet angle, pelvic inclination, obstetric conjugate, sacral outlet diameter (SOD), and coccygeal pelvic outlet were measured in the sagittal section. The interspinous diameter and intertuberous diameter were measured in coronal sections. Fetal anomalies, cesarean deliveries before the onset of labor, and non-reassuring fetal status were excluded from the analysis. MRI pelvimetry was performed in 154 patients. After excluding 76 cases, including 19 cases of absolute cephalopelvic disproportion, 78 cases of trial of labor were included. Of these, 63 were vaginal deliveries and 15 were emergent cesarean deliveries due to obstructed labor. The cut-off value for body mass index (BMI) was 22.2, with an area under the curve (AUC) of 0.69, for predicting obstructed labor. The cut-off value for the SOD was 10.7cm with an AUC of 0.69. BMI alone had a sensitivity of 80%, specificity of 66%, positive predictive value (PPV) of 36%, and negative predictive value (NPV) of 93%. When BMI and SOD were combined, sensitivity was 53%, specificity was 90%, PPV was 57%, and NPV was 89%. The odds ratio for emergent cesarean delivery was 5.42 (95% confidence interval 1.06-27.6, p=0.041) if the SOD was less than the cut-off value in the binomial logistic regression analysis in cases with an BMI >22. We confirmed that MRI pelvimetry was a reliable tool for better patient selection for obstructed labor. The SOD was the best predictor of obstructed labor, with a cut-off value of 10.7cm for women with a low BMI.

Failure Analysis of Radio Frequency Coil in MRI System

Magnetic Resonance Imaging system and their working is itself very complex in nature. Any minor non-compliance will lead to failure of entire radio frequency coil. In this research paper, we are considering the failure of coil due to breakage of studs on outer frame during assembly. Seven Quality Control Techniques are used to find the root cause and check the effectiveness of implemented measures. Existing material shows extra stickiness during molding operation, that increases the stress within frame. Manual heat stacking process is used for insertion of metal insert, due to its uncontrollable measures, bulging was observed on studs. Sharp edges on the frame concentrate the stress and accelerate the breakage of stud while torquing screw. After research, we finalize alternative material which show better molding properties, introduced automation in heat stacking process and changed design of molding tool. In proto batch production, considerable change observed, like 18% decrease in maximum principal stress and 12% decrease in total deflection were observed.

Ethanol Kinetics in the Human Brain Determined by Magnetic Resonance Spectroscopy.

In many parts of the world, ethanol is a widely consumed substance that displays its effect in the brain, the target organ for desired, but also negative impact. In a previous study, the ethanol concentrations were analyzed in different regions of the brain by magnetic resonance spectroscopy (MRS). In this study, the same method is used to demonstrate the kinetics of the ethanol concentration in the human brain after oral ethanol uptake. A drinking study was performed with 10 healthy participants. After the uptake of ethanol in a calculated amount leading to a plasma ethanol concentration of 0.92 g/L (19.95 mM corresponding to a blood ethanol concentration of 0.7 g/kg), brain ethanol concentrations were continuously measured by means of MRS on a 3 Tesla human magnetic resonance imaging (MRI) system. For the data acquisition a single-voxel sLASER sequence was used, with the volume of interest located in the occipital cortex. Intermittently, blood samples were taken and plasma was analyzed for ethanol using headspace gas chromatography with flame ionization detection (HS-GC-FID). The obtained MRS brain ethanol curves showed distinct inter-individual differences; however, a good intra-individual correlation of plasma and brain ethanol concentrations was observed. The results suggest a rapid equilibration between blood and brain. The ethanol concentrations measured in the brain were substantially lower than the measured plasma ethanol results, suggesting an MRS visibility of about 63% for ethanol in brain tissue. The maximum individual ethanol concentrations in the brain (normalized to water content) ranged between 7.1 and 14.1 mM across the cohort, while the highest measured plasma concentrations were in the range between 0.35 g/L (9.41 mM) and 0.95 g/L (20.52 mM).

Classifying youth with bipolar disorder versus healthy youth using cerebral blood flow patterns.

Clinical neuroimaging studies often investigate group differences between patients and controls, yet multivariate imaging features may enable individual-level classification. This study aims to classify youth with bipolar disorder (BD) versus healthy youth using grey matter cerebral blood flow (CBF) data analyzed with logistic regressions. Using a 3 Tesla magnetic resonance imaging (MRI) system, we collected pseudo-continuous, arterial spin-labelling, resting-state functional MRI (rfMRI) and T 1-weighted images from youth with BD and healthy controls. We used 3 logistic regression models to classify youth with BD versus controls, controlling for age and sex, using mean grey matter CBF as a single explanatory variable, quantitative CBF features based on principal component analysis (PCA) or relative (intensity-normalized) CBF features based on PCA. We also carried out a comparison analysis using rfMRI data. The study included 46 patients with BD (mean age 17 yr, standard deviation [SD] 1 yr; 25 females) and 49 healthy controls (mean age 16 yr, SD 2 yr; 24 females). Global mean CBF and multivariate quantitative CBF offered similar classification performance that was above chance. The association between CBF images and the feature map was not significantly different between groups (p = 0.13); however, the multivariate classifier identified regions with lower CBF among patients with BD (ΔCBF = -2.94 mL/100 g/min; permutation test p = 0047). Classification performance decreased when considering rfMRI data. We cannot comment on which CBF principal component is most relevant to the classification. Participants may have had various mood states, comorbidities, demographics and medication records. Brain CBF features can classify youth with BD versus healthy controls with above-chance accuracy using logistic regression. A global CBF feature may offer similar classification performance to distinct multivariate CBF features.