Mach Probe Research Articles

Study of Plasma Flow Velocity in an Open SMOLA Screw Trap

The physics of confinement of a rotating plasma in a magnetic field with linear helical symmetry is being studied at the Institute of Nuclear Physics SB RAS on the open SMOLA trap. An indicator of the quality of confinement is the plasma flow velocity in the system. The paper describes the applied diagnostics based on the Mach probe under conditions of non-magnetized plasma, which made it possible to determine the longitudinal flow velocity in experiments. The measured longitudinal flow velocity was (0.5–5) · 106 cm/s in various operating modes of the installation. The dependence of the speed on the magnitude of the magnetic field corrugation is discussed. A reverse flow of trapped particles returning to the containment zone has been detected.

All-in-one probe for exploring self-organized two-fluid equilibria in toroidal plasmas.

This paper presents the development of an all-in-one probe to simultaneously measure all components of the generalized Ohm's law in reversed-field pinch plasmas and tokamaks. The polyhedral configuration of the Mach probe is achieved through the specific arrangement, angle, and depth of the collimator channel apertures drilled into the surface of a hollow boron nitride cylinder encasing it. This probe includes a central Mach probe to assess the ion velocity field in three dimensions. Initial tests at the RELAX and Madison Symmetric Torus machines have confirmed the probe's effectiveness, revealing an octahedron form similar to a tetrahedron. The probe seems to function correctly and is expected to facilitate the empirical validation of two-fluid equilibria at the periphery of toroidal plasmas.

Investigation of Plasma Flow Velocity in the Helical Magnetic Open Trap SMOLA

The physics of confinement of plasma rotating in the magnetic field with linear helical symmetry is studied at the SMOLA open trap at Budker Institute of Nuclear Physics of the Siberian Branch of the Russian Academy of Sciences. The factor characterizing the quality of plasma confinement in the system is its flow velocity. The paper describes the diagnostics applied, which is based on the Mach probe used under the conditions of nonmagnetized plasma; this diagnostics made it possible to determine the longitudinal flow velocity in the experiments. In different operating regimes of the device, the measured longitudinal flow velocity was (0.5−5) × 106 cm/s. It is discussed how the velocity depends on the magnetic field corrugation. The reverse flow of trapped particles returning to the confinement zone was detected.

Measurement of ion temperature and toroidal flow during magnetic reconnection with a large guide field

Ion temperature and toroidal flow along the guide field direction are measured using a new ion tomographic diagnostic on the Magnetic Reconnection eXperiment (MRX) during magnetic reconnection with a guide field strength of about 1.4 and 2.1 times the strength of the reconnecting component. Strong toroidal flows, beyond what has been measured in anti-parallel and lower guide field conditions on MRX, are observed. Sustained ion heating with no discernible structure within the measurement region is also observed. Probe measurements including Langmuir and Mach probe measurements are made to support the tomographic inversion of line-integrated measurements, as well as to provide local measurements of plasma parameters. Measurements of toroidal velocity and ion temperature are supported with time series data. Energy flow into and out of the X-line region is estimated using a guiding center framework and presented in the Appendix of this manuscript, suggesting an outsized role played by parallel electric field in energizing ions. The guiding center approximation is not well satisfied in the region of interest; however, the estimates provide a springboard for future, further experimentation.

Mach probe diagnostic for determining positive ion fluxes in H- ion sources

In NNBI ion sources neutral hydrogen atoms and positive ions impacton low work function grid surfaces where they are converted to negative ions, andsubsequently extracted. Knowledge of the positive ions flux iscrucial for optimizing the negative ion yield, and also for benchmarking numericalmodels. To this end a Mach probe (MP) diagnostic can be used, which determines thedirection and magnitude of the positive ion flux. The plasma in ion sources is typicallyweakly magnetized, rendering the interpretation of Mach probe data difficult. Forthis reason a two step approach is chosen, where at first a previously used Machprobe is re-commissioned and applied in a well diagnosed and versatile laboratoryscale experiment. From these experiments important insights regarding the designof a new combined Langmuir- and Mach probe, its calibration procedure, and datainterpretation are obtained.

Development and numerical investigation of Mach probe model in a hypersonic, low-temperature flowing plasma

This study conducted a numerical simulation around a Mach probe under hypersonic low-temperature plasma. The Mach probe has three ion collection planes: front, side, and back. Under a hypersonic flowing plasma, the front and side planes are practical ion collection areas, and the backplane collects no ion flux. The collected ion current density on the front plane is almost identical to that of the mainstream ion flux. By contrast, the ion current collected on the side plane is affected by the concentration of the electric field at the probe edge. As this edge effect has a different influence on the front and side planes, the ion current density ratio of the side to the front planes is dominated by a non-dimensional parameter—the ratio of electrostatic to kinetic flow energy. Based on this non-dimensional parameter, the calculated ion current density ratio can be fitted using a simple mathematical formula. Therefore, the proposed Mach probe model with non-dimensional parameters extends the conventional Mach probe model validated in sub-to-supersonic high-temperature plasma to hypersonic low-temperature flowing plasma, which is commonly observed in electric propulsions.

Measurement of Mach probe on plasma flow velocity in highly collisional plasma jet

A normalized plasma flow velocity in highly collisional plasma formed by a microwave plasma jet, which is dimensionless unit for plasma flow velocity/ion acoustic velocity, was measured by the parallel Mach probe. To deduce the normalized plasma flow velocity under highly collisional plasma conditions, the collisional model of a Mach probe was proposed. In addition, neutral gas flow velocity which assumed to be plasma flow velocity was calculated by the turbulent model. The results for the two different models were compared with those for the collsionless models of the Mach probe. The turbulent model produced 2–4 times reduced values than by measurements with collsionless models. The measured results with the collisional model were shown as approximately 100–250% lower than those for collsionless models. They were obtained to be in good agreement with difference rate of 10–30% when compared to those for the turbulent model.

High-heat flux ball-pen probe head in ASDEX-Upgrade.

A new high heat flux ball-pen probe head installed on the midplane manipulator is currently being used in ASDEX-Upgrade (AUG). The probe was designed to withstand high heat fluxes making possible the investigation of the plasma edge under harsh conditions, such as low power H-mode. Composed of seven pins (four Langmuir probes, mounted in two Mach probe pairs, and three ball-pen probes), the new probe head allows us to measure several plasma parameters simultaneously and with high temporal resolution. A novel method to correct the sheath potential dynamically accounting for the total secondary electron emission is introduced together with applications to obtain the electron temperature and plasma potential profiles. The total secondary electron emission yield is obtained from particle in cell simulations in AUG condition and probe realistic impact angle with respect to the magnetic field. Finally, the probe capability to investigate turbulence around the separatrix of AUG is discussed.

Development of plasma sources and diagnostics for the simulation of fusion edge plasmas

Although the research on divertors and scrape-off layers (SOLs) has been not as focused on as the recent success of the Korean fusion program, a few linear plasma devices have been developed for simulating divertor and SOL plasmas: (1) diversified plasma simulator (DiPS), a versatile linear machine, has been developed for simulations of divertor and space plasmas with various electric probes, such as single, triple, and Mach Probes and gridded energy analyzer. DiPS consists of two major parts: a divertor plasma simulator with a \(\hbox {LaB}_6\) DC plasma source and a space plasma simulator with a helicon RF plasma source, (2) divertor plasma simulator-1 (DiPS-1) is a part of DiPS with only a \(\hbox {LaB}_6\) cathode, where a low-power laser-induced fluorescence (LIF) is added and more electric probe diagnostics are augmented; it is dedicated only for fusion edge and divertor plasmas, (3) Divertor Plasma Simulator-2 (DiPS-2) has been modified from the DiPS-1 by adding a magnetic nozzle with a limiter structure and by removing the helicon source and space chamber. DiPS-2 is a linear plasma device with a 4-inch \(\hbox {LaB}_6\) cathode, the same as DiPS-1, and it is focused on the development of various diagnostics, such as those used for LIF and laser Thomson scattering (LTS) along with various electric probes, on the divertor and scrape-off plasmas and on the plasma-material interaction (PMI) research, such as that of tungsten and graphite as plasma-facing components (PFCs), (4) A Multi-Purpose Plasma (\(\hbox {MP}^2\)) device is a renovation of the Hanbit mirror device [Kwon et al., Nucl. Fusion 43, 686 (2003)] with the installation of two plasma sources: \(\hbox {LaB}_6\) (DC) and helicon (RF) plasma sources. A honeycomb-like large-area \(\hbox {LaB}_6\) (HLA-\(\hbox {LaB}_6\)) cathode has been developed for the divertor plasma simulation to improve the resistance against the thermal shock fragility for large (8-inch) and high density plasma generation, (5) DiPS-2 has been augmented by adding another cylindrical device, called the Dust interaction with Surfaces Chamber (DiSC) for the generation and diagnostics of dusts. This combined system (DiPS-2+DiSC) has added two more diagnostics: Laser Photo-Detachment (LPD) for dust density and laser Mie Scattering (LMS) for dust size. Moreover, dusts or negative ions have been analyzed by using electric probes and capacitive diagram gauges in Transport and Removal of Dusts (TReD) device.

The role of B T-dependent flows on W accumulation at the edge of the confined plasma

Near-separatrix impurity accumulation between the crown and the outer midplane of tokamaks is a common feature in results from codes such as SOLPS-ITER and DIVIMP; however, experimental evidence of accumulation has only recently been obtained and is reported here. The codes find that the poloidal distribution of impurity ions in the scrape-off layer (SOL) depends primarily on toroidal field (B T)-dependent parallel flow patterns of the background plasma and the parallel ion temperature gradient (∇‖ T ion) force. Experimentally, Mach probes used in L-mode plasmas with favorable (for H-mode access) B T measure fast (M ∼ 0.3–0.5) inner-target-directed (ITD) background plasma flows at the crown of single-null discharges. This study reports a set of DIVIMP simulations for two similar H-mode discharges from the DIII-D W metal rings campaign differing primarily in B T-direction to assess the effect that fast ITD flows have on the distribution of W ions in the SOL. It is found that for imposed ITD flows of M = 0.3, W ions that otherwise accumulate due to the ∇‖ T ion-force are largely flushed out. It is also found that doubling the radial diffusion coefficient from 0.3 to 0.6 m2 s−1 prevents accumulation due to rapid cross-field transport into the far-SOL, where background plasma flows drain W ions to the divertors. Far-SOL W distributions from DIVIMP are then used to specify input to the impurity transport code 3DLIM, which is used to interpretively model collector probe (CP) deposition patterns measured in the ‘wall-SOL’. It is demonstrated that the deposition patterns are consistent with the DIVIMP predictions of near-SOL accumulation for the unfavorable-B T direction, and little/no accumulation for the favorable-B T direction. The wall-SOL CPs have thus provided the first experimental evidence, albeit indirect, of near-SOL W accumulation—finding it occurs for the unfavorable-B T direction only. For the favorable-B T direction, fast flows can largely prevent accumulation from occurring.

Скорость вращения плазмы в отражательном разряде с термокатодом

This work is devoted to determining the azimuthal ion rotation velocity in a reflex discharge with a thermionic cathode. For the experimental determination of the ion velocity, a Mach probe with directional particle collection was used. The Mach probe rotation velocity measurements are compared with the drift speed in crossed ExB fields, where the radial electric field is measured with an emissive probe. The rotation of the plasma was found to be predominantly due to this drift, corrected for centrifugal effects. One of the important results of the work is the determination of the ion temperature. The obtained value Ti=0.12 eV, agrees with the ion temperature estimates in works with similar experimental conditions. A general parameter has been obtained that makes it possible to estimate the necessity to take into account centrifugal effects under given conditions.

Velocity of plasma rotation in reflex discharge with themionic cathode

This work is devoted to determining the azimuthal ion rotation velocity in a reflex discharge with a thermionic cathode. For the experimental determination of the ion velocity, a Mach probe with directional particle collection was used. The Mach probe rotation velocity measurements are compared with the drift speed in crossed Ex B fields, where the radial electric field is measured with an emissive probe. The rotation of the plasma was found to be predominantly due to this drift, corrected for centrifugal effects. One of the important results of the work is the determination of the ion temperature. The obtained value Ti=0.12 eV, agrees with the ion temperature estimates in works with similar experimental conditions. A general parameter has been obtained that makes it possible to estimate the necessity to take into account centrifugal effects under given conditions. Keywords: plasma, thermionic cathode, reflex discharge, ion rotation, crossed fields.

Characteristics of Plasma Flow for Microwave Plasma Assisted Aerosol Deposition.

To validate the possibility of the developed microwave plasma source with a novel structure for plasma aerosol deposition, the characteristics of the plasma flow velocity generated from the microwave plasma source were investigated by a Mach probe with pressure variation. Simulation with the turbulent model was introduced to deduce calibration factor of the Mach probe and to compare experimental measurements for analyses of collisional plasma conditions. The results show calibration factor does not seem to be a constant parameter and highly dependent on the collision parameter. The measured plasma flow velocity, which witnessed fluctuations produced by a shock flow, was between 400 and 700 m/s. The optimized conditions for microwave plasma assisted aerosol deposition were derived by the results obtained from analyses of the parameters of microwave plasma jet. Under the optimized conditions, Y2O3 coatings deposited on an aluminum substrate were investigated using scanning electron microscope. The results presented in this study show the microwave plasma assisted aerosol deposition with the developed microwave plasma source is highly feasible for thick films with >50 μm.

A fast-reciprocating probe array for two-dimensional measurements in the divertor region of the Tokamak à configuration variable.

A detailed description of the construction and commissioning of the fast-moving reciprocating divertor Langmuir probe array on the Tokamak à Configuration Variable (TCV) is presented. A horizontal array of 24 Langmuir probes (12 Mach probes) combined with a fast vertical movement provides unprecedented two-dimensional measurements of the plasma properties across the entire divertor outer leg volume and up to the X-point. The L-shape probe arm has to be very compact to minimize plasma perturbations and, at the same time, has to house 24 coaxial transmission lines, withstand time-averaged heat fluxes of up to ≈30MW/m2 and accelerations of up to 8g, and be resilient to violent plasma disruptions. For the fast vertical motion of the probe arm, extending up to 38cm into the TCV vacuum vessel, an assembly with a precise and powerful linear electric motor (up to 4000 N of force) was mounted in a 4m high structure within the limited space below the TCV. The diagnostic has already performed measurements in ≈200 plasma discharges and has been hit by ≈20 disruptions without suffering any critical damage. The measurements are qualitatively and quantitatively consistent with other reference diagnostics, such as upstream electron Thomson scattering and downstream wall-embedded Langmuir probes, and are used extensively on the TCV for experimental divertor studies and for comparisons with edge transport and turbulence code results.

Development of a set of movable electrostatic probes to characterize the plasma in the ITER neutral beam negative-ion source prototype

We present the development and first use of a set of movable electrostatic probes on the full-scale ITER heating neutral beam prototype negative-ion source SPIDER. The probes access the ion source plasma from the multi-aperture accelerator aiming at the study of the plasma formation and expansion from the RF drivers through the transverse magnetic filter. The magnetic filter separates the relatively high electron-temperature region for plasma formation and hydrogen dissociation form the negative-ion extraction region in which low electron-temperature is required to avoid negative-ion destruction, but also causes non-uniformities and drifts in the large plasma discharge which will be studied by this setup. The set of electrostatic probes encompasses eight RF-compensated Langmuir probes, one double probe, one Mach probe for the assessment of plasma drift velocities, and two gridded retarding field energy analyzers to measure the positive-ion energy distribution function. Electric aspects as well as mechanical constraints given by the large in-vacuum movable structure, and thermal requirements of these relatively heat-flux components made the design challenging. Prototyping and commissioning of the measurement system is discussed offering examples of measured characteristics with the various probes.

Effect of background fluctuation on velocity diagnostics by Mach probe

The effect of background fluctuation on velocity diagnostics is discussed and studied. The kinetic theory of Mach probe (MP) and the theory of BGK mode are combined to evaluate how the measurement of MP is affected by electrostatics fluctuation. It is found that the quantity of speed by the MP model is closer to the effective velocity in the picture of momentum flux rather than the real mean velocity, while, with high fluctuation, the fitting parameter of MP’s exponential formula should be corrected.

Experimental Investigation of the Effects of Magnetic Mirrors on Plasma Transport in the Prototype Material Plasma Exposure Experiment

The Prototype Material Plasma Exposure eXperiment (Proto-MPEX) at Oak Ridge National Laboratory is developing a helicon radio frequency (RF) source for plasma production along with microwave electron heating and RF ion heating. Proto-MPEX has several magnetic mirrors that affect plasma transport. The magnetic field near the helicon source is ~ 0.05 T, and the peak magnetic field in Proto-MPEX is ~ 1.8 T, which results in a large magnetic well for particles sourced at the helicon transporting toward the target region. Keeping the helicon source field and the target field constant, experiments have been conducted by methodically changing the magnetic field, at a local axial location, within the source and the target. Plasma flow measurements using Mach probes have shown a decrease in the flow as a function of the magnetic mirror ratio. Plasma flows were further investigated with ion cyclotron resonant heating (ICH). Results with the addition of ICH measured upstream of the antenna have shown a decrease in Mach number as a function of mirror ratio when compared to helicon discharges. Such flow behavior demonstrated slowing down of the plasma due to the increased reverse plasma flow toward the helicon plasma source. However, in high magnetic fields, when the resonant magnetic field moved away from the ICH antenna, no effects on the plasma flow due to ICH were observed.

Coherence imaging spectroscopy at Wendelstein 7-X for impurity flow measurements.

In the last decade, Coherence Imaging Spectroscopy (CIS) has shown distinctive results in measuring ion flow velocities in the edge of magnetically confined plasma devices. Its 2D spatially resolved measurement capabilities and its high optical throughput are ideal for investigating the impurity behavior in the complex 3D magnetic island topology edge of Wendelstein 7-X (W7-X). However, a highly precise and stable calibration method is required for a reliable diagnostic operation. A new level of precision and stability has been achieved for the two CIS systems installed at W7-X with the use of a new calibration source, a continuous tunable laser commercially available only since 2015. A specific prototype model was successfully adapted to the challenging requirements of W7-X, granting high accuracy (±0.01 pm) and flexibility (spectral range: 450-650 nm) in the wavelength calibration required for measuring low-Z impurity ion flow velocities. These features opened up new investigation possibilities on temperature stability and wavelength response of the CIS components, allowing to fully characterize and validate the W7-X systems. The CIS diagnostic was operational throughout the last W7-X experimental campaign. Measured velocities on the order of ∼20-30 km/s were observed, corroborated by comparisons with measurements with Mach probes.

High Resolution Probe for filament transport and current density study at the edge region of W7-X

For the study of electrostatic and magnetic properties of filaments characterizing the edge region of the stellarator experiment W7-X, a specifically designed insertable probe head was constructed within the framework of EUROfusion WP.S1 work package in collaboration between Consorzio RFX, IPP Greifswald and Forschungszentrum Jülich. The probe head, named High Resolution Probe (HRP), was conceived to be installed on the mid-plane multi-purpose fast reciprocating manipulator on W7-X. Electromagnetic filamentary turbulent structures are found to characterize the edge region of different magnetic configurations including Reversed Field Pinch, stellarator and tokamak, where strong currents are associated also to ELM filamentary structures. The study of those phenomena in W7-X stellarator is of particular interest as the electromagnetic features of filaments are expected to become more relevant with the increase of the local plasma beta. In particular the aim is to provide information about the presence and the features of parallel current density associated to filamentary turbulent or ELM-like structures. Furthermore, the possibility to measure the time evolution of the flow radial profiles using the Mach probe array was considered as a further interesting part of the study, given the strong interplay expected between the turbulent fluctuations and the average flows. Further important information provided is the radial propagation of turbulent flux. The contribution will present the design development, the R&D studies and the applied solutions for the sensors embedded in the probe head. In particular, the presence of 140 GHz ECRH plasma environment represents one of the main challenges for reliable magnetic fluctuation measurements. First measurements were performed during the W7-X experimental campaign OP1.2b, where electromagnetic features of turbulence were measured with the probe, at different magnetic configurations.

Operation of probe heads on the Multi-Purpose-Manipulator at W7-X in OP 1.2a

The Multi-Purpose-Manipulator (MPM) has been operated, as a versatile carrier system for probes, since the first campaign OP. 1.1 in 2015 at Wendelstein 7X. The MPM is mounted at the outboard midplane and is able to perform fast plunges through the entire scrape off layer up to the last closed flux surface. In addition, a system for gas injection was commissioned that allowed the use of a dedicated probe head and a port on the existing probes for fueling and impurity seeding experiments. A combined probe, a combination of Langmuir, Mach and magnetic probes, was used. For the second campaign OP. 1.2a in 2017, with an island divertor, an upgraded combined probe, a fluctuation probe, a retarding field analyzer, a Mach probe array, a laser blow off target and a material probe holder were added to the range of plasma edge diagnostics. The new diagnostic probe heads were designed to address specific tasks, such as measuring the edge fluctuations, the ion temperature and the radial Mach number profiles. However, all fast plunging probes were designed such that they provide the most important quantities for SOL characterization (electron temperature, density, radial electric field).