Lunar Prospector Gamma Ray Spectrometer Research Articles

Lunar elemental abundances as derived from Chandrayaan-2

The distribution of Mg, Al, Si, Ca and Fe on the lunar surface are important to understand the petrological characteristics of the Moon and its geological evolution. We derived new elemental distribution maps using the Chandrayaan-2 Large Area Soft X-ray Spectrometer (CLASS) experiment onboard the Chandrayaan-2 Orbiter. These are the first set of maps derived from three years of CLASS data (2019–2022) at a spatial resolution of 150 km × 12.5 km. These maps are free of the topographic shadow effects and space weathering effects because the elemental abundances are derived only using X-ray spectra in the 0.5 to 20 keV energy range. CLASS derived abundances are compared to the elemental maps obtained using the Lunar Prospector Gamma Ray Spectrometer, with abundances of the lunar soil samples, and with XRF measurements of Chandrayaan-1 mission to establish its credibility. These maps derived using X-ray fluorescence spectroscopy are a new resource for lunar geochemical studies based on the most direct detection technique.

Comprehensive mapping of lunar surface chemistry by adding Chang'e-5 samples with deep learning

Lunar surface chemistry is essential for revealing petrological characteristics to understand the evolution of the Moon. Existing chemistry mapping from Apollo and Luna returned samples could only calibrate chemical features before 3.0 Gyr, missing the critical late period of the Moon. Here we present major oxides chemistry maps by adding distinctive 2.0 Gyr Chang’e-5 lunar soil samples in combination with a deep learning-based inversion model. The inferred chemical contents are more precise than the Lunar Prospector Gamma-Ray Spectrometer (GRS) maps and are closest to returned samples abundances compared to existing literature. The verification of in situ measurement data acquired by Chang'e 3 and Chang'e 4 lunar rover demonstrated that Chang’e-5 samples are indispensable ground truth in mapping lunar surface chemistry. From these maps, young mare basalt units are determined which can be potential sites in future sample return mission to constrain the late lunar magmatic and thermal history.

Determining the age of Vaughan, a potential source crater for lunar meteorites, using boulder size-frequency distributions

We use Lunar Reconnaissance Orbiter Camera (LROC) Narrow Angle Camera (NAC) images to analyze the boulder distribution around Vaughan crater, a small, fresh crater on the far side of the Moon. Using six similar lunar impact craters of known age for comparison, we determine the approximate age of the crater. Vaughan crater lies in a part of the South Pole-Aitken basin that is compositionally similar to lunar meteorite Dhofar 961, on the basis of Lunar Prospector Gamma Ray Spectrometer data, making Vaughan crater a potential candidate for the source of this meteorite and possibly others paired with it. Boulder distributions reveal that as impact craters age, the boulder population density in their ejecta decreases. This understanding allows us to use size-frequency distributions to compare crater ages on the basis of their boulder population density. We find that Vaughan crater is very young (<25 Ma) owing to its placement within the boulder size-frequency comparison plot and its population of large (>10 m diameter) boulders. Additionally, we compare LROC NAC distributions to thermophysically derived values for rock abundance from the Diviner Lunar Radiometer. We find that our LROC NAC count is consistent with Diviner rock abundance values, which further supports the inference that Vaughan is a very young impact crater and could plausibly be a source of lunar meteorite Dhofar 961.

The Scientific Value of a Sustained Exploration Program at the Aristarchus Plateau

Abstract The Aristarchus plateau hosts a diversity of volcanic features, including the largest pyroclastic deposit on the Moon, the largest sinuous rille on the Moon, and intrusive and extrusive examples of evolved, Th-rich silicic lithologies. We provide an overview of previous remote-sensing measurements of the Aristarchus plateau and provide new analyses of Diviner Lunar Radiometer thermal IR data, Lunar Prospector Gamma Ray Spectrometer Th data, Chang’e-5 Microwave Radiometer data, and hyperspectral and multispectral visible/near-infrared images and spectra from the Chandrayaan-1 Moon Mineralogy Mapper and the Kaguya Multispectral Imager. The rich diversity of volcanic features on the Aristarchus plateau presents an opportunity for a sustained science and exploration program. We suggest a series of missions to the Aristarchus crater floor or ejecta, the Cobra Head, and Herodotus Mons to investigate the link between pyroclastic, effusive basaltic, and silicic volcanism in the region. Such missions would enable analyses of silicic rocks that are rare in the Apollo sample collection and demonstrate in situ resource utilization of FeO- and H2O-bearing pyroclastic materials.

Possible Non‐Mare Lithologies in the Regolith at the Chang’E‐5 Landing Site: Evidence From Remote Sensing Data

AbstractThe Chang’E‐5 (CE‐5) mission returned a total of 1,731 g of lunar regolith from the northern Oceanus Procellarum (NOP). Despite that the CE‐5 landing site is covered by Eratosthenian‐aged mare basalts, non‐mare lithologies might also have been collected owing to the lateral mixing introduced by nearby craters. Here we employed FeO and thorium abundance data obtained by the Lunar Prospector Gamma Ray Spectrometer to investigate the chemical composition of the NOP region. Four major compositional groups (feldspathic highland materials, Imbrium basin ejecta, Aristarchus ejecta, and mare basalts) and several subgroups have been identified. Their corresponding geographical locations were constrained using an interactive scatter‐plot tool in ENVI® software. We also determined the first‐order mixing trends occurring within the NOP region as well as the CE‐5 landing site. Aristarchus crater may have contributed highly evolved materials to the CE‐5 site. Rock fragments derived from Aristarchus ejecta are important for the interpretation of magmatic differentiation and non‐mare volcanism on the Moon. We proposed that thorium enrichments of CE‐5 landing site are due to the geochemical nature of local mare basalts rather than impact mixing. Highland ejecta, along with mare basalts, would expand Apollo and Luna sample collection diversity.

Global mapping of lunar refractory elements: multivariate regression vs. machine learning

Context.The quantitative estimation of elemental concentrations at the spatial resolution of hyperspectral near-infrared (NIR) images of the lunar surface is an important tool for understanding the processes relevant for the origin and evolution of the Moon.Aims.We aim to map the abundances of the elements Fe, Ca, and Mg at a typical accuracy of about 1 wt.% at the spatial resolution of the Moon Mineralogy Mapper (M3) instrument on-board Chandrayaan-1 lunar mission.Methods.The NIR reflectance of the lunar regolith is an integrated response to the presence of refractory elements and soil alteration processes. Our approach was to define a combination of spectral parameters that are robust with respect to the effects of soil maturity. We calibrated the spectral parameters with respect to elemental abundances measured by the Lunar Prospector Gamma Ray Spectrometer (LP GRS) and the Kaguya GRS (KGRS). For this purpose, we compared a classical multivariate linear regression (MLR) approach and the machine learning based support vector regression (SVR) technique applied to M3global observations.Results.The M3-based global elemental maps are consistent in distribution and range with the LP GRS and KGRS elemental maps and do not show artifacts in immature areas such as small fresh craters. The results derived using MLR and SVR are compared to sample-based ground truth data of the Apollo and Luna sample-return sites, where the root-mean-square deviations obtained by the two regression models are similar.Conclusions.The main advantage of the proposed new algorithm is its ability to minimize artifacts due to space-weathering effects. The elemental maps of Mg and Ca provide additional information and reveal structures not always visible in the Fe map. The global elemental abundance maps derived for the fully calibrated M3observations might thus serve as important tools to investigate the lunar geology and evolution.

Iron distribution of the Moon observed by the Kaguya gamma-ray spectrometer: Geological implications for the South Pole-Aitken basin, the Orientale basin, and the Tycho crater

In this study we describe the distribution of iron on the Moon as obtained by the Kaguya high energy resolution gamma-ray spectrometer (KGRS). We achieved for the first time the identification of iron based on the fast neutron flux obtained by the KGRS. The iron distribution obtained by KGRS is compared to that of the Lunar Prospector Gamma-Ray Spectrometer (LP GRS), showing that the FeO distributions observed by KGRS and LP GRS, in general, are in good agreement. Furthermore, we compare the iron content data obtained by KGRS and LP GRS to spectral reflectance measurements of the Clementine, Kaguya and Chandrayaan-1 spacecraft as well as those inferred from returned samples. We found differences in FeO concentration and distribution in areas of moderate abundance (6–15 wt%) of the South Pole-Aitken basin, Mare Orientale, and around the crater Tycho crater. It implies that high concentrations of FeO at Mare Ingenii in the South Pole-Aitken basin and Mare Orientale are due to the presence of mare basalts, whereas the enriched FeO content in the central depression of the South Pole-Aitken basin and the Tycho crater indicates the presence of mafic materials such as impact melt breccia.

New Insights Into Lithology Distribution Across the Moon

AbstractLithology distribution across the Moon is pivotal for understanding lunar evolution. However, so far, the distribution of lunar rock suites is still uncertain; as a result, many related core issues on lunar evolution have long been in dispute. This work reports on a new lithology distribution map across the Moon and discusses some critical issues of the lunar evolutionary process. The oxide abundances derived from Chang'E‐1 Interference Imaging Spectrometer imagery and the Th contents inferred by Lunar Prospector Gamma Ray and Neutron Spectrometer data are employed to generate the lithological map by using the decision tree C5.0 algorithm. The following conclusions are inferred from this new map. (1) Magnesian suite is widely distributed across the Feldspathic Highlands Terrane and in the periphery of the South Pole‐Aitken Terrane. Thus, the viewpoints have been validated that the early magnesian magmatism may be a global phenomenon and that KREEP basalt is not necessary for the petrogenesis of Mg‐rich rocks. Moreover, the regions of Dryden, Chaffee S, Theophilus, and Moscoviense are confirmed as magnesian suite exposures. (2) The observation that the Feldspathic Highlands Terrane has a higher Mg/(Mg + Fe) value than the maria is related to the flood of the Mg suite across the Feldspathic Highlands Terrane. (3) The specific exposed locations of the alkali suite across the Moon have long been unsolved, and this work discloses that the alkali suite prevails in the outskirts of the Procellarum KREEP Terrane, the center of the South Pole‐Aitken Terrane, and some isolated locales. (4) Focusing on distinguishing mare basalts from other mafic rocks, seven geochemical indices are proposed to determine the potential exposures of mare basalts across the Moon. (5) In Mare Insularum, a series of KREEP volcanisms may have occurred and lasted longer than the mare volcanism.

Lunar mare TiO2 abundances estimated from UV/Vis reflectance

The visible (400–700 nm) and near-infrared (700–2800 nm) reflectance of the lunar regolith is dominantly controlled by variations in the abundance of plagioclase, iron-bearing silicate minerals, opaque minerals (e.g., ilmenite), and maturation products (e.g., agglutinate glass, radiation-produced rims on soil grains, and Fe-metal). The same materials control reflectance into the near-UV (250–400 nm) with varying degrees of importance. A key difference is that while ilmenite is spectrally neutral in the visible to near-infrared, it exhibits a diagnostic upturn in reflectance in the near-UV, at wavelengths shorter than about 450 nm. The Lunar Reconnaissance Orbiter Wide Angle Camera (WAC) filters were specifically designed to take advantage of this spectral feature to enable more accurate mapping of ilmenite within mare soils than previously possible. Using the reflectance measured at 321 and 415 nm during 62 months of repeated near-global WAC observations, first we found a linear correlation between the TiO2 contents of the lunar soil samples and the 321/415 nm ratio of each sample return site. We then used the coefficients from the linear regression and the near-global WAC multispectral mosaic to derive a new TiO2 map. The average TiO2 content is 3.9 wt% for the 17 major maria. The highest TiO2 values were found in Mare Tranquillitatis (∼12.6 wt%) and Oceanus Procellarum (∼11.6 wt%). Regions contaminated by highland ejecta, lunar swirls, and the low-TiO2 maria (e.g., Mare Frigoris, the northeastern units of Mare Imbrium) exhibit very low TiO2 values (<2 wt%). We find that the Clementine visible to near-infrared based TiO2 maps (Lucey et al., 2000) have systematically higher values relative to the WAC estimates. The Lunar Prospector Gamma-Ray Spectrometer (GRS) TiO2 map is consistent with the WAC TiO2 map, although there are local offsets possibly due to the different depth sensitivities and large pixel scale of the GRS relative to the WAC. We find a wide variation of TiO2 abundances (from 0 to 10 wt%) for early mare volcanism (>2.6 Ga), whereas only medium to high TiO2 values (average = 6.8 wt%, minimum = 4.5 wt%) are found for younger mare units (<2.6 Ga).

The petrology, geochemistry, and age of lunar regolith breccias Miller Range 090036 and 090070: Insights into the crustal history of the Moon

Meteorites ejected from the surface of the Moon as a result of impact events are an important source of lunar material in addition to Apollo and Luna samples. Here, we report bulk element composition, mineral chemistry, age, and petrography of Miller Range (MIL) 090036 and 090070 lunar meteorites. MIL 090036 and 090070 are both anorthositic regolith breccias consisting of mineral fragments and lithic clasts in a glassy matrix. They are not paired and represent sampling of two distinct regions of the lunar crust that have protoliths similar to ferroan anorthosites. 40Ar-39Ar chronology performed on two subsplits of MIL 090070,33 (a pale clast impact melt and a dark glassy melt component) shows that the sample underwent two main degassing events, one at ~3.88 Ga and another at ~3.65 Ga. The cosmic ray exposure data obtained from MIL 090070 are consistent with a short (~8–9 Ma) exposure close to the lunar surface. Bulk-rock FeO, TiO2, and Th concentrations in both samples were compared with 2-degree Lunar Prospector Gamma Ray Spectrometer (LP-GRS) data sets to determine areas of the lunar surface where the regolith matches the abundances observed on the sample. We find that MIL 090036 bulk rock is compositionally most similar to regolith surrounding the Procellarum KREEP Terrane, whereas MIL 090070 best matches regolith in the feldspathic highlands terrane on the lunar farside. Our results suggest that some areas of the lunar farside crust are composed of ferroan anorthosite, and that the samples shed light on the evolution and impact bombardment history of the ancient lunar highlands.

Lunar iron and optical maturity mapping: Results from partial least squares modeling of Chang'E-1 IIM data

Iron and optical maturity (OMAT) are two key geological marks of the Moon that closely related to its geochemical evolution and interactions between surface and space environment. We apply Partial Least Squares (PLS) regression to Chang'E-1 Imaging Interferometer (IIM) (32 bands between 480 and 960nm) in mapping lunar global FeO and OMAT, and the FeO and OMAT values are derived based on reasonable spectral parameters (absorbance, band ratios, TiO2 and maturity sensitive parameters, etc.). After been calibrated by the FeO map from Lunar Prospector Gamma-Ray Spectrometer (LP-GRS), the global FeO map derived from PLS modeling shows a quantitatively more reasonable result consistent with previous remote sensing results (LP) as well as lunar feldspathic meteorite studies and Chang'E-3 landing site. Based on the new FeO map by Chang'E-1, we discover a compositional inhomogeneity across lunar highland regions, which has not been suggested by previous datasets (e.g., Clementine UVVIS). Furthermore, we suggest that at least part of the FeO enrichments in highlands would be caused by mixing of highland and mare materials. The IIM derived OMAT map does not suggest a dichotomy of the lunar highlands and mare regions, implying the compositional differences between those two terrains have been suppressed. We further check the maturity effect for the young mare basalts (<3.0Ga), and find that (1) the OMAT values of the young basaltic units with medium and high FeO and TiO2 show a linear decrease with ages; (2) units with ultrahigh-FeO (>20wt%) and ultrahigh-TiO2 (>10wt%) tend to have greater OMAT values and vary little with ages; (3) this may be due to the distinct optical maturity effects of ultramafic minerals (i.e., ultrahigh Fe and Ti) and/or the spectral blue shifts of abundant ilmenite.

Estimation of lunar FeO abundance based on imaging by LRO Diviner

Understanding the abundance and distribution characteristics of FeO on the surface of the Moon is important for investigating its evolution. The current high resolution maps of the global FeO abundance are mostly produced with visible and near infrared reflectance spectra. The Christiansen Feature (CF) in mid-infrared has strong sensitivity to lunar minerals and correlates to major elements composing minerals. This paper investigates the possibility of mapping global FeO abundance using the CF values from the Diviner Lunar Radiometer Experiment aboard the Lunar Reconnaissance Orbiter (LRO) mission. A high correlation between the CF values and FeO abundances from the Apollo samples was found. Based on this high correlation, a new global map (±60°) of FeO was produced using the CF map. The results show that the global FeO average is 8.2 wt.%, the highland average is 4.7 wt.%, the global modal abundance is 5.4 wt.% and the lunar mare mode is 15.7 wt.%. These results are close to those derived from data provided by Clementine, the Lunar Prospector Gamma Ray Spectrometer (LP-GRS) and the Chang'e-1 Interference Imaging Spectrometer (IIM), demonstrating the feasibility of estimating FeO abundance based on the Diviner CF data. The near global FeO abundance map shows an enrichment of lunar major elements.

Estimation of lunar major elemental abundances in Chang’E-3 landing site based on Active Particle-induced X-ray Spectrometer (APXS)

Elemental abundance provides an effective vehicle to understand lunar petrologic characteristics and evolutional history. The APXS mounted on the Yutu rover provides a valuable opportunity to determine the major elemental abundances in lunar soil within a short distance. In this study, we processed the APXS spectra including energy calibration, dead time correction and nonlinear least-squares fitting, and determined the abundances of the lunar major elements using the fundamental parameter method. In the calculation of X-ray fluorescence yield, a finite element method (FEM) was employed to improve the accuracy. The major elemental abundances derived from Chang’E-3 (CE-3) APXS possess a good consistency with the result of LP-GRS (Lunar Prospector gamma-ray spectrometer) data in the landing region. Compared with the chemical composition of the returned lunar rock samples, we draw the conclusion that the lunar soils in CE-3 landing site are fragments of mare basalts. Our conclusion is supported by the geological map of Mare Imbrium.

Constraining the source regions of lunar meteorites using orbital geochemical data

AbstractLunar meteorites provide important new samples of the Moon remote from regions visited by the Apollo and Luna sample return missions. Petrologic and geochemical analysis of these meteorites, combined with orbital remote sensing measurements, have enabled additional discoveries about the composition and age of the lunar surface on a global scale. However, the interpretation of these samples is limited by the fact that we do not know the source region of any individual lunar meteorite. Here, we investigate the link between meteorite and source region on the Moon using the Lunar Prospector gamma ray spectrometer remote sensing data set for the elements Fe, Ti, and Th. The approach has been validated using Apollo and Luna bulk regolith samples, and we have applied it to 48 meteorites excluding paired stones. Our approach is able broadly to differentiate the best compositional matches as potential regions of origin for the various classes of lunar meteorites. Basaltic and intermediate Fe regolith breccia meteorites are found to have the best constrained potential launch sites, with some impact breccias and pristine mare basalts also having reasonably well‐defined potential source regions. Launch areas for highland feldspathic meteorites are much less well constrained and the addition of another element, such as Mg, will probably be required to identify potential source regions for these.

Evidence for explosive silicic volcanism on the Moon from the extended distribution of thorium near the Compton‐Belkovich Volcanic Complex

AbstractWe reconstruct the abundance of thorium near the Compton‐Belkovich Volcanic Complex on the Moon, using data from the Lunar Prospector Gamma Ray Spectrometer. We enhance the resolution via a pixon image reconstruction technique and find that the thorium is distributed over a larger (40km × 75 km) area than the (25km × 35 km) high‐albedo region normally associated with Compton‐Belkovich. Our reconstructions show that inside this region, the thorium concentration is 14–26ppm. We also find additional thorium, spread up to 300km eastward of the complex at ∼2 ppm. The thorium must have been deposited during the formation of the volcanic complex, because subsequent lateral transport mechanisms, such as small impacts, are unable to move sufficient material. The morphology of the feature is consistent with pyroclastic dispersal, and we conclude that the present distribution of thorium was likely created by the explosive eruption of silicic magma.

Lunar cryptomaria: Mineralogy and composition of ancient volcanic deposits

Ancient lunar volcanic deposits, known as cryptomaria, have been detected by remote telescopic and orbital measurements since the 1970s. Cryptomaria are most easily identified by the presence of dark-halo impact craters and are associated with a mare basalt mineralogy, which is indicated by two pyroxene spectral absorption features near 1μm and 2μm in the visible to near-infrared (VNIR) wavelengths. However, there are many early igneous lithologies that have been identified in the Apollo sample collection that have a similar VNIR spectral signal, implying a pyroxene-dominant mineralogy. In this study we use high resolution Moon Mineralogy Mapper (M3) VNIR spectral data and the Modified Gaussian Model (MGM) to determine cryptomare mineralogy as well as Lunar Prospector gamma-ray spectrometer (LP GRS) FeO and Th compositional measurements to evaluate which ancient igneous rocks (e.g., low-Ti mare basalt, high-Ti mare basalt, Mg-suite rocks, dunite, high-Al mare basalt, KREEP basalt) are consistent with our mineralogical observations. In addition, spectra from different M3 optical periods were compared to determine how the MGM-derived absorption band centers vary between datasets. Band center differences between optical periods are on the order of ~6±4nm and ~25±10nm for the 1μm and 2μm features, respectively. Cryptomare mineralogies are dominated by clinopyroxene and are consistent with measurements from locally exposed mare basalts. LP GRS measurements support a mare basalt rock type when regolith mixing is taken into account.

A comparative study of iron abundance estimation methods: Application to the western nearside of the Moon

The FeO weight percentage (wt.%) abundance of the Moon’s western nearside (55°S–55°N and 5°E–40°W) is estimated using data from the InfraRed Spectrometer-2 (SIR-2) and the Moon Mineralogy Mapper (M3). In this study, we modified an FeO abundance estimation algorithm (Bhatt, M., Mall, U., Bugiolacchi, R., McKenna-Lawlor, S., Banaszkiewicz, M., Nathues, A., Ullaland, K. [2012]. Icarus 220, 51–64) which relies exclusively on the 2-μm absorption band parameters. The modified FeO abundance estimation algorithm and the regression-based elemental abundance estimation algorithm (Wöhler, C., Grumpe, A., Berezhnoy, A., Bhatt, M.U., Mall, U. [2014]. Icarus 235, 86–122) which is based on the 1-μm and 2-μm absorption band parameters is applied to the M3 data. We have compared results obtained from these two modified algorithms with a previously published Clementine’s FeOwt.% map (Lucey, P.G., Blewett, D.T., Jolliff, B.L. [2000]. J. Geophys. Res. 105, 20297–20306). The effects of topography and space weathering on FeOwt.% estimates have been successfully minimized using the modified algorithm based on the 2-μm absorption band parameters. Thus, this algorithm can be successfully applied at middle to high latitudes. Furthermore, a correction for TiO2 is applied to the FeO abundance estimation algorithm based on the 2-μm absorption band parameters using the M3 data. Our comparative study shows a good correspondence between the three algorithms discussed. There are two locations: the crater Tycho and the region around Rima Bode which show major discrepancies. Our modified algorithm based on the 2-μm absorption parameters predicts 3–4wt.% less FeO for the ray system of Tycho than for the surrounding region. The average iron abundance for the lunar highlands is about 6wt.% and for the mare regions is about 16wt.% using the regression-based elemental abundance estimation algorithm and the algorithm based on the 2-μm absorption parameters. This result is consistent with the previous analysis using Lunar Prospector Gamma-Ray Spectrometer data sets. The FeOwt.% is in the range 20–24wt.% for the high-Ti basalts using both the modified iron abundance estimation and the regression-based elemental abundance estimation algorithms.

Integrated topographic, photometric and spectral analysis of the lunar surface: Application to impact melt flows and ponds

This study provides an analysis of the impact melt deposits (melt flows and ponds) associated with eight lunar craters with diameters between 9 and 96km in terms of their topographic, photometric and spectral properties. Our analysis is based on an integrated method for construction of digital elevation models (DEM) of high lateral resolution, pixel-wise photometric modelling, construction of topographically corrected normalised reflectance maps, extraction of spectral parameters and estimation of elemental abundances based on Moon Mineralogy Mapper (M3) hyperspectral data and data of the Lunar Prospector Gamma Ray Spectrometer instrument. Most of the examined geologically fresh impact melt flows are characterised by lower albedos than the surrounding surface and tend to originate from topographically low parts of the source crater rim. As an exception, we find that the impact melt deposits northeast of crater Aristillus lack any optical signature and are not visible in monochrome images, but can only be observed by their anomalously smooth surface inferred from the DEM. Some impact melt flows and ponds exhibit photometric anomalies in terms of the asymmetries in the single-particle scattering function and the slope of that parameter with respect to wavelength. These photometric anomalies may be due to impact melt specific anomalies of the surface structure, e.g. consolidated rock rather than regolith, or anomalies in size or shape of the geometric surface elements (e.g. individual grains or their aggregates) on submillimetre spatial scales. The strength of the hydroxyl absorption displays a negative anomaly with respect to the surrounding surface for the majority of the examined impact melt flows. As an impact melt specific spectral behaviour, we find a decrease in the absorption band depth around 2000nm and (in several cases) a simultaneous increase of the absorption band depth near 1000nm. These observations are consistent with the laboratory analyses by Tompkins et al. (Tompkins, S., Pieters, C.M. [2010]. Meteorit. Planet. Sci. 45 (7), 1152–1169) of chemically uniformly composed mixtures between crystalline and glass material. For several impact melt flows, their data allow to roughly estimate the fraction of glass material based on our spectral analysis.

Lunar surface heat flow mapping from radioactive elements measured by Lunar Prospector

An accurate estimate of global surface heat flow is important because it provides strong constraints on interior thermal model and understanding of the thermal state and geologic evolution of the Moon. In this paper, a distribution map of lunar surface heat flow is derived from calibrated Lunar Prospector gamma-ray spectrometer data (K, U and Th abundances). It shows that surface heat flow varies regionally from about 10.6mW/m2 to 66.1mW/m2, which is in the same order of magnitude as previous results. In the calculation, lunar surface heat flow includes the heat flow from the non-uniform distribution of radioactive elements K, U and Th and that from secular cooling of the Moon. The calculation of heat flow from radioactive elements is based on the assumption that the radioactive decay of K, U and Th on the Moon is the same as that on the Earth. The heat flow from secular cooling of the Moon is assumed to be equal to the global average radioactive heat flow. Firstly we construct a relationship between radioactive elements K, U and Th and lunar surface heat flow. The key parameter of the characteristic length scale in the relationship is determined by measured surface heat flow and Th abundances at Apollo 15 and 17 landing sites. Then the distribution of lunar surface heat flow is derived by combining other parameters such as lunar crustal thickness measured by Clementine and lunar crustal density. In addition, correlation analysis of the three radioactive elements is carried out due to the higher resolution of Th abundance and for ease of calculation.

New insights into the global composition of the lunar surface from high-energy gamma rays measured by Lunar Prospector

[1] An analysis of the lunar gamma-ray spectrum as measured by the Lunar Prospector Gamma-Ray Spectrometer has revealed that 8–8.9 MeV gamma rays contain information about the elemental composition of near-surface materials. These high-energy gamma rays are found to be primarily sensitive to the total Fe and Mg content of the surface, although other elements also contribute. This information has been used to identify several regions with unique compositions, including the Hertzsprung and Orientale basins. A method for deriving global Mg abundances from high-energy gamma-ray measurements is presented. The physical mechanism for high-energy gamma-ray production is proposed to be radiation produced during the decay of galactic cosmic ray produced pions within the lunar surface. Laboratory measurements of pion production cross sections are found to be consistent with the empirically derived relationship between the lunar Fe, Mg, and Ti abundances and the measured high-energy gamma-ray count rates.