Low Output Power Research Articles

Assessment of Vehicle-Integrated Photovoltaics: A financial and environmental perspective

Integrating photovoltaic (PV) technology into electric vehicles (EVs) promises an environmentally friendly transportation solution by increasing the energy efficiency of vehicles. On the other hand, the limited integration area of the vehicle causes PVs to have relatively lower power output. This situation creates a discussion about how reasonable a solution for PV-EV integration is from various perspectives. This study aims to provide a realistic assessment of PV-EV integration using manufacturer-provided data on solar-assisted EVs in the market. Assessments are examined in three categories: financial assessment based on payback period, environmental assessment based on carbon emissions, and usage-based assessment based on charging dependency. The findings indicate that the PV systems integrated into contemporary solar-assisted market vehicles demonstrate a return on investment within 8.7 years. From an environmental perspective, hybrid vehicles can provide up to a 12 % reduction in carbon emissions, while fully EVs can achieve reductions of up to 32.5 %. Usage-based assessments showed that PV-EV integration is especially advantageous for countries with low daily travel distances. According to the assessment, the use of PV panels in vehicles can potentially extend the usage time without recharging by up to 170 %.

Power increase potential of coal-fired power plant assisted by the heat release of the thermal energy storage system: Restrictions and thermodynamic performance

The integration of a thermal energy storage (TES) system is an effective way to improve the load cycling rate of coal-fired power plants (CFPPs). To evaluate the power increase potential and thermodynamic performance of CFPP supplied by heat release of the molten salt TES system, eight discharging modes for CFPP integrated with the TES system including steam injection, heater bypass, and additional turbine schemes were comparatively evaluated. The system simulation models of the integrated systems were developed and the thermodynamic performance of the proposed system were evaluated. Results show that the mode SI-HPT (high-pressure turbine steam injection) has the largest output power increase of 25.00 % under the benchmark condition of 75%THA, but the mode HB-LPH (low-pressure heater bypass) shows a very low output power increase of 2.08 %. Moreover, the power generation efficiency is changed by the external heat source through a change in the average heat absorption temperature of the Rankine cycle and the internal irreversibility of the steam/water cycle. Under the typical benchmark discharging condition of 75%THA, the power generation efficiency of the turbine in mode SI-LPT (low-pressure turbine steam injection) can be reduced from 47.41 % to 44.15 %, but it can be increased from 47.41 % to 48.86 % in mode SI-HPT. When the temperature ranges of the TES system are above 600 °C and below 450 °C, the modes SI-HPT and SI-LPT obtain the optimal comprehensive performance, respectively. This study can provide the scientific guidance for retrofit for CFPP to achieve efficient and flexible design.

PH Dependence of Dihydroxyacetone Oxidation by Electrocatalytic Viologen Self-Assembled Monolayers on Gold Electrodes.

Carbohydrate fuel cells garner much research interest as the world's focus shifts from fossil fuels to renewable energy. Many catalyst options are available for carbohydrate fuel cell development, including enzymes and microbes, various metal-based catalysts, and natural or synthetic mediators. Research challenges include low power output, system fouling and poisoning, inefficient electron release, and complex mechanisms, with multiple pathways leading to low product selectivity. Here, we further investigate a novel approach to catalyze carbohydrate oxidation using Au electrodes with viologen self-assembled monolayers (SAMs). SAM-mediated fuel cells have the potential to address the challenges of other catalyst systems by protecting the electrode surface and controlling the local concentration and structure to increase current generation. The effects of increasing pH on dihydroxyacetone (DHA) oxidation by three viologen SAMs on Au electrodes are presented. Current and power generated during DHA oxidation at varying pH were measured and compared to those of bare Au performance. Two of the SAMs produced more current and power than bare Au at elevated pH. The SAM system produced more current and peak power per molecule than both dilute and concentrated homogeneous viologen systems in the same cell setup. These results demonstrate the benefits and limitations of electrodes modified with redox-active groups for the production of electricity from simple sugars and other carbohydrate sources. These results are encouraging for the development of new strategies for electrical power generation from renewable resources.

Research on the Advantages and Challenges of Replacing LEDs with Lasers in Functional Near-Infrared Spectroscopy Systems Based on Advanced Signal Processing Algorithms

Abstract: Functional near infrared spectroscopy (fNIRS) has received increasing attention as a non-invasive, portable brain hemodynamic monitoring tool due to its potential for use in natural Settings. Traditional fNIRS systems commonly use light-emitting diodes (LEDs) as light sources, which have become the mainstream choice because of their low cost, easy integration, low heat output, and availability of a variety of near-infrared wavelengths. However, LEDs are limited by their low optical output power and broad wavelength range, which restrict their effectiveness in deep tissue penetration and signal quality. In contrast, Laser Diodes (LD) have the advantages of good monochromaticity and high optical output power, which can provide deeper tissue penetration and higher signal stability. Therefore, this study explores the feasibility of using lasers instead of leds in fNIRS systems and their impact on signal quality and imaging depth. By comparing the performance of LED and laser-based fNIRS systems, it is evident that lasers provide significant improvements in signal quality and imaging depth, although they face challenges in terms of cost, thermal management, and safety. The research in this paper provides an important reference for the future design of fNIRS system, especially in the application scenarios requiring high precision imaging.

Performance Analysis of Cement Plant Waste‐Heat Recovery for Power Generation Based on Partial Evaporating Cycle with Ejector

In the cement industry, much waste heat is released into the environment. The organic Rankine cycle is widely utilized to harness waste heat for power generation. However, significant energy is lost in the heat recovery process due to the finite temperature difference between the heat source and working fluid, resulting in low power output andefficiency. To enhance the heat recovery from the cement flue gas and increase power output and overall efficiency, a novel partial evaporating cycle with ejector is proposed and investigated in this study. Pinch point analysis is performed to characterize the heat recovery process in the evaporator. The effects of the evaporating temperature, outlet quality of the evaporator, and exit pressure of the primary expander on system performance are also investigated. Results show that partially evaporating the fluid improves heat matching and reduces the irreversibilities in the evaporator by up to 18.1% when the outlet quality of the fluid is 0.33. Maximum net power of 803.15 kW can be generated with an evaporating temperature of , outlet quality of 0.33, and expander exit pressure of 1054.9 kPa. Additionally, the inclusion of the ejector increases the net power produced by up to 76.07 kW.

Quaternized poly(aryl imidazolium) containing bulky binaphthyl group as proton exchange membrane for high-temperature fuel cells

The low power output and high phosphoric acid (PA) leakage are the main constraints restricting the commercialization of PA-doped high-temperature proton exchange membranes (HT-PEMs). Ionized imidazoles have been shown to be an effective strategy to improve PA retention, however, less research has been conducted on the fractional free volume (FFV) of the backbone of the main chain on PA loss. Herein, novel imidazolium ions polymer (PQBN-4-IM) material with bulky binaphthyl (BN) group was prepared as PA-doped HT-PEM using a one-step superoxid acid catalyzed polycondensation and subsequent methylation process. The rigidity and hydrophobicity of the BN group promote PQBN-4-IM PEM to produce more obvious microphase separation morphology and large FFV, which is beneficial for forming better ion transport channels and excellent PA interaction. Notably, the PA-doped PQBN-4-IM (PQBN-4-IM/PA) membrane has the highest proton conductivity (90.26 mS cm−1, 180 ℃) and peak power density (PPD) (802.5 mW cm−2, 180 ℃) than PQTP-4-IM/PA and m-PBI/PA HT-PEMs. Moreover, the PQBN-4-IM/PA membrane has higher PA retention at 80 ℃/40 % relative humidity (RH), 40 ℃/60 % RH, or immersed in water due to enhancement on ion-pair interactions by microstructure. Under the accelerated stress test (AST) of the fuel cell (FC), the PQBN-4-IM/PA membrane loses only 12.22 % of PPD after 200 cycles at 80 ℃, which exhibits higher PPD retention than that of the PQBP-4-IM/PA (70.23 %), PQTP-4-IM/PA (74.36 %) and m-PBI/PA (65.25 %) membranes, and shows excellent durability of cell performance for more than 1000 h without significant voltage decay at 160 °C. Thus, the outstanding performance suggests that the microstructure and morphology of imidazolium ions polymer membranes significantly influence proton conductivity, performance, and the durability of a cell.

Enhancing microbial fuel cell performance with free-standing three-dimensional N-doped porous carbon anodes

Microbial fuel cells (MFCs) utilize microorganisms as catalysts to transform the chemical energy to electrical power. However, the practical application of MFCs is currently impeded by low power output, which is caused by insufficient microbial colonization on the anode, slow extracellular electron transfer at the microbe-anode interface, and low oxygen reduction reaction catalytic efficiency at the cathode. Herein, a three-dimensional (3D) hierarchical porous anode of Carbonization-CTS-MF/rGOtempreture (CCMF/rGOT) by pyrolyzing crosslinked composite of melamine formaldehyde resin (MF), chitosan (CTS) and graphene oxide (GO). The macroporous anode provides a biocompatible surface for exoelectrogens and 3D electron transfer pathways. In addition, an appropriate balance of graphitic-N and pyrrolic-N content optimizes both conductivity and the number of active sites, thereby synergistically enhancing extracellular electron transfer (EET) efficiency. Therefore, the power density of CCMF/rGO1000 anode is 11.28 W/m3, which surpasses the CCMF1000 anode without 3D reduced graphene oxide (rGO) conductive network (10.04 W/m3), and traditional carbon cloth anode (4.36 W/m3). Moreover, the anode runs stably for more than 200 days with a maximum operating voltage of 0.69 V, which achieves chemical oxygen demand (COD) removal rate of 95.4 %. This work provides a promising strategy to prepare a free-standing 3D anode with enriched exoelectrogens and enhanced EET to improve the MFCs performance.

Energy harvesting properties for potassium-sodium niobate piezoceramics through synergistic effect of phase structure and texturing engineering

In order to address the energy dilemma and meet environmental protection requirements, it is an urgent need to develop lead-free piezoelectric energy harvesters (PEHs). However, the low output power density has seriously hindered the application of lead-free piezoceramics as high efficiency energy harvesters. To solve above question, the combination of phase structure regulation and texturing technique in the K0.5Na0.5NbO3-xBi0.5Na0.5ZrO3-0.5%wtBiFeO3 (KNN-xBNZ) ceramics was adopted in this work. Because of both the Rhombohedral-Orthorhombic-Tetragonal (R-O-T) multiphases coexistence and texturing engineering, an ultrahigh piezoelectric activity quality factor d33×g33 ∼ 18324 ×10-15 m2·N-1 was achieved in the textured KNN-0.05BNZ (T-KNN-0.05BNZ) ceramics, which is about third times higher than that of random KNN-0.05BNZ (R-KNN-0.05BNZ) (d33×g33 ∼ 6672 ×10-15 m2·N-1) ones. A high output power of ∼ 0.32 mW was also obtained in the T-KNN-0.05BNZ ceramics by cantilever beam-based energy harvester devices under the resonance frequency of 75 Hz and matched RL of 1.2 MΩ, suggesting that the T-KNN-0.05BNZ ceramics have a great potential for application in the PEHs devices. This result also reveals that the combination of phase structure regulation and texturing technique is an effective way to achieved a high energy harvesting performances.

Recent Advances in Enzyme‐based Biofuel Cells Using Glucose Fuel: Achieving High Power Output and Enhanced Operational Stability

AbstractAn enzyme‐based biofuel cell (EBFC) is widely regarded as one of the most efficient power sources for bio‐friendly and implantable medical devices, capable of converting electrochemical reactions into electrical currents under physiological conditions. However, despite its potential, the practical and commercial use of EBFCs is limited by their low power output and operational instability. Therefore, significant research efforts have focused on increasing power output and stability by improving electron transfer between enzymes and host electrodes and developing efficient enzyme immobilization techniques. However, most EBFCs produced by current methods still deliver unsatisfactory performance. A promising approach to address these challenges is the use of conductive linkers that promote favorable interfacial interactions between adjacent enzymes and between enzymes and host electrodes. These linkers can facilitate electron transfer and ensure robust enzyme immobilization. In addition, designing the host electrode with a 3D structure and a large surface area can further improve the areal energy performance. This perspective reviews the working principles, types, and electron transfer mechanisms of EBFC electrodes and explores how conductive linkers and 3D host electrodes can enhance the performance of EBFC electrodes. Finally, recent advances in integrating EBFCs into biomedical devices are described.

High-performance waterproof flexible thermoelectric generators for self-powered electronics

Flexible and wearable thermoelectric generators (TEG) have emerged as promising energy sources for wearable health-monitoring devices. However, common thermoelectric generators are difficult to be applied to a wide range of application scenarios due to their poor durability, low output power, and susceptibility to human sweat or underwater environments. Here, we propose a waterproof wearable TEG with a gap structure. Through structural optimization and full-coverage elastomer encapsulation, the wearable TEG has a maximum power density of 4.38 mW∙cm−2 at a temperature difference (ΔT) of 30 K and exhibits good stability under aqueous environments, which is capable of supplying power to electronic devices even under submerged conditions. The internal resistance of wearable TEG changes by less than 10 % at 50 % stretch or 900 degrees of torsion, showing good flexibility and mechanical stability. Based on this, we designed an energy harvesting and management system to help wearable TEG collect and utilize energy on demand, and successfully implemented wireless transmission of human skin temperature data for underwater environments and real-time electrocardiograms (ECG) tests for health detection in air environments. This research provides a reliable method for powering wearable electronic devices using thermoelectric generators.

Proposal design and thermodynamic optimization of an afterburning-type isothermal compressed air energy storage system integrated with molten salt thermal storage

The isothermal compressed air energy storage is a potential technique for large-scale energy storage. In this study, the molten salt thermal storage is integrated with the afterburning-type isothermal compressed air energy storage system, which uses liquid piston compression technique, to enhance the thermal performances. Thermodynamic models of the hybrid energy storage system were developed, and the genetic algorithm was used to optimize multiple parameters to enhance the energy efficiency. Four operation modes, i.e., the high, medium-high, medium-low, and the low output power modes were proposed, to enhance the operational flexibility of the hybrid energy storage system. When the system operates in the operation mode of medium-low output power, a portion of afterburning heat is stored in the molten salt and used in the operation mode of low output power. Results show that the roundtrip efficiency of high, medium-high, medium-low, and the low output power modes are 63.57 %, 59.33 %, 57.13 %, and 83.28 %, respectively. Exergy analysis was carried out to quantify the irreversibilities of key components. In the three modes of operation with afterburning, the combustion chamber has the highest portion of exergy loss, and in the operation mode without afterburning, the exergy loss of heat exchangers is higher than that of expanders.

Impact of Nano-TiO2 Combination with Biodiesel on Diesel Engine Performance and Emissions Under Fuel Magnetism Conditioning

AbstractProblems of atomization, spray, and lower output power are due to the biodiesel’s higher viscosity. All of these aim to encourage fuel magnetism and nanoparticles addition to reduce fuel consumption. Waste cooking oil was converted to methyl ester by transesterification. To make methyl ester blend, diesel and biodiesel were mixed at volume ratio of 20%. TiO2 nanoparticles were added to biodiesel blend B20 at doses of 25 and 50 mg/L. TEM and XRD were used to characterize the nanomaterials. A magnetic coil was placed before the fuel injector to apply a magnetic field on the line of fuel. South pole of the magnetic field is located near to the fuel line, whereas the north pole is located further away. To examine the impact of these nanomaterials with fuel magnetism on engine performance and emissions using WCO biodiesel mixture, an experimental test rig was built connected to diesel engine. During testing, diesel engine operates at 1500 rpm with load variation. The average increases in BTE were 1, 1.5, 3.5, 5.5, and 6.5% but the decreases in BSFC were 1.2, 2, 4, 5, and 6% for B20 + magnet, B20 + 25 TiO2, B20 + 25 TiO2 + magnet, B20 + 50 TiO2, and B20 + 50 TiO2 + magnet, respectively, at engine load range. The average drops in CO, NOx, and HC concentrations were 16, 22, and 33%, respectively, at load range for B20 + 50 TiO2 + magnet. To improve engine performance and reduce emissions, biodiesel blend B20 from waste cooking oil with nanoTiO2 concentration of 50 ppm under magnetic field effect was recommended as a substitute fuel in diesel engine.

High-performance hydrogel membranes with superior environmental stability for harvesting osmotic energy

A collection of innovative nanofluidic systems has been developed to harness Gibbs free energy and convert it into osmotic energy. Nevertheless, these systems frequently encounter challenges such as low output power density, inadequate mechanical stability, and diminished performance in extreme conditions. In this work, we utilized a simple thermal polymerization method to fabricate a charged phytic acid (PA)–acrylic acid (AA)–3-sulfopropyl acrylate potassium salt (SPAK) hydrogel (PASH) membrane with anti-drying and anti-freezing properties, alongside mechanical stability. Using a silicon window with a testing area of 3 × 10−8 m2, a high power density of 30.94 W/m2 was achieved in artificial seawater and river water environments (0.5/0.01 M NaCl). Notably, an even higher power density of 103.9 W/m2 was attained in artificial saline lake and river water environments (5/0.01 M NaCl). Meanwhile, the PASH membrane demonstrated outstanding performance in low temperatures and various acidic and alkaline environments, offering the potential for osmotic power generation in extreme conditions. This work provides essential theoretical foundations and experimental evidence for the development of sustainable osmotic energy conversion technologies, contributing to the advancement and innovation in the field of blue osmotic energy.

Research on mid-infrared quantum cascade lasers spectral beam combining

Quantum cascade lasers (QCLs) in the mid-infrared (MIR) hold significant potential for widespread applications in both military and civilian contexts. However, the utility of present single-chip QCLs is hampered by issues such as low output power and subpar beam quality. This study addresses these limitations by employing spectral beam combining (SBC) based on a diffraction grating, with an aim to enhance both power and beam quality of MIR QCLs. Coaxial power synthesis of three single-chip QCLs (around 4.75 μm) is achieved experimentally, importantly, the beam quality did not decrease after combining, essentially maintaining the same quality as before combining. It is proposed that there are four main factors affecting the combining efficiency, namely operating optical power (or driving current) of the chips, individual differences in QCL chips, diffraction grating, and reflectivity of feedback mirror, and their effects on the combining efficiency are discussed separately. This study confirms that SBC is an effective way to obtain high-power and high-beam quality MIR QCL sources, and lays a research foundation for more beam spectral combining.

Hydrocarbonoclastic Biofilm-Based Microbial Fuel Cells: Exploiting Biofilms at Water-Oil Interface for Renewable Energy and Wastewater Remediation.

Microbial fuel cells (MFCs) represent a promising technology for sustainable energy generation, which leverages the metabolic activities of microorganisms to convert organic substrates into electrical energy. In oil spill scenarios, hydrocarbonoclastic biofilms naturally form at the water-oil interface, creating a distinct environment for microbial activity. In this work, we engineered a novel MFC that harnesses these biofilms by strategically positioning the positive electrode at this critical junction, integrating the biofilm's natural properties into the MFC design. These biofilms, composed of specialized hydrocarbon-degrading bacteria, are vital in supporting electron transfer, significantly enhancing the system's power generation. Next-generation sequencing and scanning electron microscopy were used to characterize the microbial community, revealing a significant enrichment of hydrocarbonoclastic Gammaproteobacteria within the biofilm. Notably, key genera such as Paenalcaligenes, Providencia, and Pseudomonas were identified as dominant members, each contributing to the degradation of complex hydrocarbons and supporting the electrogenic activity of the MFCs. An electrochemical analysis demonstrated that the MFC achieved a stable power output of 51.5 μW under static conditions, with an internal resistance of about 1.05 kΩ. The system showed remarkable long-term stability, which maintained consistent performance over a 5-day testing period, with an average daily energy storage of approximately 216 mJ. Additionally, the MFC effectively recovered after deep discharge cycles, sustaining power output for up to 7.5 h before requiring a recovery period. Overall, the study indicates that MFCs based on hydrocarbonoclastic biofilms provide a dual-functionality system, combining renewable energy generation with environmental remediation, particularly in wastewater treatment. Despite lower power output compared to other hydrocarbon-degrading MFCs, the results highlight the potential of this technology for autonomous sensor networks and other low-power applications, which required sustainable energy sources. Moreover, the hydrocarbonoclastic biofilm-based MFC presented here offer significant potential as a biosensor for real-time monitoring of hydrocarbons and other contaminants in water. The biofilm's electrogenic properties enable the detection of organic compound degradation, positioning this system as ideal for environmental biosensing applications.

Scaling of ultrashort-pulsed laser structuring processes for electromobility applications using a spatial light modulator

The structuring of lithium-ion battery (LIB) electrodes and the diffusion media (DM) for polymer electrolyte membrane fuel cells (PEMFCs) with ultrashort laser pulses enables improved performance characteristics of both technologies. However, the transfer of the approaches from a laboratory scale to a commercial use has previously been hindered by the low average output power of ultrashort-pulsed (USP) laser beam sources and the limited productivity of single-beam structuring using scanning optics. Recent advancements in the development of USP laser systems have led to a steady increase in the available output power, thereby enabling new fields of applications. This study aims at accelerating the USP laser structuring of LIB electrodes and DM for PEMFCs to industrially relevant processing rates by comparing a single-beam with a multibeam structuring process regarding ablation characteristics and quality. For the multibeam strategy, the shape of the laser beam was modified by a spatial light modulator (SLM). In addition to microholes, the insertion of microchannels was investigated to demonstrate the high flexibility of state-of-the-art SLMs. The geometry of the created structures was measured with a laser scanning microscope, and the different layers were tested for their geometrical and electrochemical properties to compare both technologies. The results confirmed that applying an SLM enables high-quality microstructures with significantly higher structuring rates. Furthermore, this contribution includes a theoretical analysis of the specifications required for a laser setup to reach an industrially relevant productivity of the structuring processes.

High-power and ultra-wide-tunable fiber-type external-cavity diode lasers

High-power and wide-tunable fiber-type external-cavity diode lasers (FTECDLs) are of pivotal importance across various scientific and practical applications, such as polarization lidar, communication, sensing, and spectroscopy. As the output power and tuning characteristics are currently much lower than the saturation power and bandwidth of semiconductor gain media, further improvements conventionally require additional gain media in parallel and external amplifiers, resulting in lower energy efficiency and complex configurations. This study implemented energy manipulation in FTECDLs with a single gain medium, overcoming the mutual restriction between low damage threshold and laser output power. This approach makes it possible to completely exploit the intrinsic performance of the semiconductor gain medium. We demonstrated various FTECDL designs, achieving a maximum tuning range of 226.8 nm, maximum output power of 160 mW, and maximum optical signal-to-noise ratio of 86.3 dB with different configurations. These results are the highest levels ever achieved for E, S, C, L, and U bands. Additionally, the achieved polarization extinction ratio of nearly 38 dB has not been previously reported. Our work provides significant guidance for the design of traveling wave ring cavity (TWRC) lasers, including free-space light semiconductor and solid-state lasers with a TWRC.

Polymer-metal film induced ultrahigh output TVNG and self-powered intelligent sensor system assisted by EEMD

Tribovoltaic nanogenerators (TVNGs) based on tribovoltaic effect can output DC current directly, and has the advantages of high output current density and low internal resistance. While TVNGs have been restricted by its low output voltage and power. Herein, we have developed a metal-polymer film with a micro-uneven structure on the surface, much higher corrosion resistance and wear resistance than metal. On this basis, a centimeter-level sliding structure metal-EP/GaN-TVNG has been fabricated, which shows a high and stable long-term DC electrical output (a maximized power output of 4.19 W/m2 when matched with a 0.07 MΩ resistor, a stable output current of 2.25 A/m2 and a peak Voc of 27 V). Further, a TVNG vehicle travelling intelligent sensor and system which can integrate electrical signals collected by TVNG into digital signal processing algorithms and then feed backing to the driving system, has been designed and manufactured. As an effective method for deep analysis of signals, Ensemble Empirical Mode Decomposition (EEMD) has been used for the first time for deep processing of nanogenerator signals in this work. This work provides a new model of further development of high output TVNG and a new deep signal processing methods of TVNG/TENG signal.

Effects Of Static Versus Dynamic Stretching On Lower Extremity Power Output And Flexibility In Dancers

Effects Of Static Versus Dynamic Stretching On Lower Extremity Power Output And Flexibility In Dancers

Intensity Matters: Effect of Different Work-Matched Efforts on Subsequent Performance in Cyclists.

To assess the effect of 2 work-matched efforts of different intensities on subsequent performance in well-trained cyclists. The present study followed a randomized controlled crossover design. Twelve competitive junior cyclists volunteered to participate (age, 17 [1]y; maximum oxygen uptake, 71.0 [4.7]mL·kg-1·min-1). The power-duration relationship was assessed through 2-minute, 5-minute, and 12-minute field tests under fresh conditions (control). On subsequent days and following a randomized order, participants repeated the aforementioned tests after 2 training sessions matched for mechanical work (∼15kJ/kg) of different intensities (ie,a moderate-intensity continuous-training [60%-70% of critical power; CP] session or a session including high-intensity intervals [3-min repetition bouts at 110%-120% of the CP interspersed by 3-min rest periods]). A significantly lower power output was found in the 2-minute test after the high-intensity training session compared not only with the control condition (-8%, P < .001) but also with the moderate-intensity continuous-training session (-7%, P = .003), with no significant differences between the latter conditions. No significant differences between conditions were found for the remaining tests. As a consequence, the high-intensity training session resulted in significantly lower W' values compared to both the control condition (-27%, P = .001) and the moderate-intensity continuous-training session (-26%, P = .012), with no differences between the 2 latter conditions and with no differences for CP. A session including high-intensity intermittent efforts induces a greater fatigue, particularly in short-duration efforts and W', than a work-matched continuous-training session of moderate intensity.