Low Shear Research Articles

Organic rearing of non-castrated male pigs: welfare indicators, carcass traits, pork quality and boar taint in Duroc and Pietrain crossbreds

The main principles of organic farming as presented by the European organisation for organic food and farming are health, ecology, fairness and care, but the intrinsic quality of products is also important for consumers. Pig genotype was tested as a lever to improve animal welfare and pork quality (meat tenderness, processing ability) of organic, non-castrated males while controlling the risk for boar taint. Non-castrated Large White × Duroc (D, n = 47) or Large White × Pietrain NN (P, n = 34) males were involved in two batches, each including one group of pigs per genotype. Each group was reared in a pen from the same building on deep straw bedding (1.3 m2/pig), with a feeding zone (0.2 m2/pig) and an outdoor area (1.0 m2/pig), from 28 kg BW until slaughter at ca. 125 kg BW. All pigs received ad libitum the same growing and finishing diets, and hay. Overall, health and welfare indicators showed few problems, but the proportions of pigs with skin scratches, and tail lesions at the end of the finishing period, were lower in D than in P pigs (P < 0.05). Growth rate and final BW did not differ between genotypes. The D pigs had lower carcass lean meat content (P < 0.001) and relative proportions of ham and loin (P ≤ 0.01), and higher proportions of belly and backfat (P ≤ 0.001) than P pigs. Compared to P, loin (Longissimus muscle) of D pigs was less light and exudative and had higher chroma (P < 0.05), but pH 24 h and glycolytic potential did not differ. Loin meat of D pigs had higher intramuscular fat content (P < 0.001) and tended to have a lower shear force (P = 0.09), but cooking loss did not differ. In the ham muscles, D pigs had higher chroma than P pigs in the Gluteus medius, whereas pH 24 h did not differ in the Gluteus medius and Semimembranosus. D pigs had higher backfat concentrations of androstenone (P < 0.001), and skatole and indole (P < 0.05) than P pigs, suggesting a higher risk of rejection by consumers due to boar taint. However, only one D carcass was detected as tainted by human nose test. Altogether, organic farming of non-castrated Duroc crossbred males appears to be favourable for animal welfare, technological and several sensory pork properties provided that the risk of undesirable odours is limited through management practices.

Temperature effects on ribbon characteristics in soft gelatin capsule manufacture

In the manufacture of soft gelatin capsules using a rotary-die encapsulation machine, the formation of ribbons at the cooling drums and their subsequent mechanical performance are key attributes for a smooth machinability. In this paper we present the results of a comprehensive investigation of the intricate impact of the cooling drum temperature in the range between 5 and 25 °C on the mechanical and the microstructural properties of a highly concentrated gelatin formulation (40% w/w) typically used in soft capsule manufacture.The study demonstrates that the temperature at the cooling drums strongly affects the gelation kinetics, the gel elasticity and the tensile strength of the ribbons. The temperature correlates linearly with the storage modulus G′ under low shear deformation, i.e. the lower the temperature of the gel, the higher the gel elasticity. A reverse linear relationship was found for the temperature-dependent ultimate tensile strength (UTS) of the gelatin ribbons, i.e. a higher drum temperature leads to a higher UTS. This inverse effect of the ageing temperature on G′ and UTS can be explained by temperature-induced microstructural differences within the gel network, as indicated by FTIR spectroscopy and Differential Scanning Calorimetry (DSC) measurements. Lower ageing temperatures result in a higher number of triple helical junction zones with fewer and/or weaker hydrogen bonds, which translate into a higher gel elasticity under low shear deformation, but a lower resilience of the ribbons against rupture in tensile testing. At higher temperatures, fewer but longer and/or more thermostable triple helical links in the gel network enhance the stability of the ribbons against tensile stress.In summary, the results clearly reveal that a detailed understanding of the complex relationship between the drum temperature, the gel network structure and the mechanical properties of gelatin ribbons is essential for process optimization.

Effect of biofilm physical characteristics on their susceptibility to antibiotics: impacts of low-frequency ultrasound

Biofilms are highly resistant to antimicrobials, often causing chronic infections. Combining antimicrobials with low-frequency ultrasound (LFU) enhances antimicrobial efficiency, but little is known about the underlying mechanisms. Biofilm physical characteristics, which depend on factors such as growth conditions and age, can have significant effects on inactivation efficiency. In this study, we investigated the susceptibility of Pseudomonas aeruginosa biofilms to tobramycin, with and without LFU treatment. The biofilms were grown under low and high fluid shear to provide different characteristics. Low-shear biofilms exhibited greater thickness, roughness, and porosity and lower density, compared to high-shear biofilms. The biofilm matrix of the high-shear biofilms had a three times higher protein-to-polysaccharide ratio, suggesting greater biofilm stiffness. This was supported by microrheology measurements of biofilm creep compliance. For the low-shear biofilms without LFU, the viability of the biofilms in their inner regions was largely unaffected by the antibiotic after a 2-hour treatment. However, when tobramycin was combined with LFU, the inactivation for the entire biofilm increased to 80% after 2 h. For the high-shear biofilms without LFU, higher LFU intensities were needed to achieve similar inactivation results. Microrheology measurements revealed that changes in biofilm inactivation profiles were closely related to changes in biofilm mechanical properties. Modeling suggests that LFU changes antibiotic diffusivity within the biofilm, probably due to a “decohesion” effect. Overall, this research suggests that biofilm physical characteristics (e.g., compliance, morphology) are linked to antimicrobial efficiency. LFU weakens the biofilm while increasing its diffusivity for antibiotics.

Microbiology of human spaceflight: microbial responses to mechanical forces that impact health and habitat sustainability.

SUMMARYUnderstanding the dynamic adaptive plasticity of microorganisms has been advanced by studying their responses to extreme environments. Spaceflight research platforms provide a unique opportunity to study microbial characteristics in new extreme adaptational modes, including sustained exposure to reduced forces of gravity and associated low fluid shear force conditions. Under these conditions, unexpected microbial responses occur, including alterations in virulence, antibiotic and stress resistance, biofilm formation, metabolism, motility, and gene expression, which are not observed using conventional experimental approaches. Here, we review biological and physical mechanisms that regulate microbial responses to spaceflight and spaceflight analog environments from both the microbe and host-microbe perspective that are relevant to human health and habitat sustainability. We highlight instrumentation and technology used in spaceflight microbiology experiments, their limitations, and advances necessary to enable next-generation research. As spaceflight experiments are relatively rare, we discuss ground-based analogs that mimic aspects of microbial responses to reduced gravity in spaceflight, including those that reduce mechanical forces of fluid flow over cell surfaces which also simulate conditions encountered by microorganisms during their terrestrial lifecycles. As spaceflight mission durations increase with traditional astronauts and commercial space programs send civilian crews with underlying health conditions, microorganisms will continue to play increasingly critical roles in health and habitat sustainability, thus defining a new dimension of occupational health. The ability of microorganisms to adapt, survive, and evolve in the spaceflight environment is important for future human space endeavors and provides opportunities for innovative biological and technological advances to benefit life on Earth.

Application and Optimization of Rheological Mathematical Models in Preparation and Injection Process of Polymer Flooding

The impact of shear on the properties of polymer solutions is not fully accounted for in the simulation of conventional rheological models. To optimize the application of these mathematical models, the shear rheological characteristics of polyacrylamide at various concentrations were investigated under different shear rates and shear modes. The results indicate that pseudoplastic fluid polymers exhibit two distinct rheological characteristics within their "shear thinning" rate range. The critical shear rate at this threshold signifies the point at which shear stress begins to disrupt the structure of the polymer solution, resulting in a rheological curve that transitions from high to low shear rates without reverting back to a low-to-high state. The concentration of the solution has minimal effect on the critical shear rate of the polymer, which is primarily determined by the inherent properties of the polymer itself. The application of rheological models during preparation and injection processes can elucidate the effects of shear on polymers by analyzing changes in apparent viscosity. Furthermore, the rheological model following supercritical shear rates requires modifications to the consistency coefficient (K) and flow index (n) based on shear rheological data obtained from high to low shear rates.

The effect of flow-derived mechanical cues on the growth and morphology of platelet aggregates under low, medium, and high shear rates

Platelet aggregation is a dynamic process that can obstruct blood flow, leading to cardiovascular diseases. While many studies have demonstrated clear connections between shear rate and platelet aggregation, the impact of flow-derived mechanical signals on this process is not fully understood. The objective of this work is to investigate the role of flow conditions on platelet aggregation dynamics, including effects on growth, shape, density composition, and their potential correlation with binding processes that are characterised by longer (e.g., via αIIbβ3 integrin) and shorter (e.g., via VWF) initial binding times. In vitro blood perfusion experiments were conducted at wall shear rates of 800, 1600 and 4000 s-1. Detailed analysis of two modalities of experimental images was performed to offer insights into the morphology of platelet aggregates. A consistent structural pattern was observed across all samples: a high-density core enveloped by a low-density outer shell. An image-based 3D computational blood flow model was subsequently employed to study the local flow conditions, including binding availability time and flow-derived mechanical signals via shear rate and rate of elongation. The results show substantial dependence of the aggregation dynamics on these flow parameters. We found that the different binding mechanisms that prefer different flow regimes do not have a monotonic cross-over in efficiency as the flow increases. There is a significant dip in the cumulative aggregation potential in-between the preferred regimes. The results suggest that treatments targeting the biomechanical pathways could benefit from creating conditions that exploit these low-efficiency zones of aggregation.

Multifunctional Yb3Si2C2 with High‐Performance Terahertz Shielding for Future 6G Communications

AbstractThe development of next‐generation 6G communications is anticipated to expand into extreme environments, necessitating superior terahertz (THz) electromagnetic interference (EMI) shielding materials. Herein, structural stability, electronic and optical properties of rare earth silicide carbide Yb3Si2C2 are investigated using first principles density functional calculations and semi‐classical Boltzmann transport theory. The calculation results show Yb3Si2C2 is determined to be experimentally synthesized with high temperature stability with a certain fluctuating C2 pair orientation. In addition, Yb3Si2C2 is identified as a soft, tough, and damage‐resistant ceramic with low shear deformation resistance and easy cleavage, ensuring its durability in irradiation environments. Due to the layered structure and excellent electrical conductivity, Yb3Si2C2 demonstrates high reflectivity and low transmittance for terahertz electromagnetic waves, along with 62% solar absorptivity and 33% IR emissivity. Remarkably, the total shielding effectiveness of Yb3Si2C2 with thicknesses of 5 µm and above follows the widely‐used Simon's formula. The average total shielding effectiveness of 5 µm‐thick and 10 µm‐thick Yb3Si2C2 across the entire THz region reaches 63 and 110 dB, respectively, which turns out to be the top compared to the results reported. Therefore, the multifunctional intrinsic properties of Yb3Si2C2 materials hold great promise for miniaturized, high‐performance terahertz EMI shielding, even in extreme environments.

Numerical simulation of non-Newtonian blood flow in a human arterial bifurcation model

Hemodynamic factors play a role in atherogenesis and the localization of atherosclerotic plaques. The human aorta and coronary arteries are susceptible to arterial disease, and there have been many studies of flows in models of these vessels. Atherosclerosis is a systemic disease occurring in specific sections of the cardiovascular tree such as the carotid and the coronary arteries. This paper aims to simulate the human arterial bifurcation and investigates some hemodynamic parameters as blood propagates from the aortic artery toward the carotid artery. We analyze the velocity, static pressure, shear stress. The simulation results showed disturbed flow patterns, such as flow separation and stagnation, as well as abnormal hemodynamic parameters (HPs) distributions including the low and high wall shear stress (WSS) and oscillation of wall shear stress. Based on our simulating characteristic results, the CFD tools can not only monitor the hemodynamic parameters obviously, but also help to analyze the diagnostic for the treatment of vascular diseases. CFD can be an effective technology for the examination and treatment of patients with failure of blood supply of the head and brain.

Response and resilience of carbon nanotube micropillars to shear flow

Interactions between carbon nanotubes (CNTs) and fluid flows are central to the operation of several emerging nanotechnologies. In this paper, we explore the fluid-structure interaction of CNT micropillars in wall-bounded shear flows, relevant to recently developed microscale wall shear stress sensors. We monitor the deformation of CNT micropillars in channel flow as the flow rate and wall shear stress are gradually varied. We quantify how the micropillars bend at low wall shear stress, and then will commonly tilt abruptly from their base above a threshold wall shear stress, which is attributed to the lower density of the micropillars in this region. Some micropillars are observed to flutter rapidly between a vertical and horizontal position around this threshold wall shear stress, before settling to a tilted position as wall shear stress increases further. Tilted micropillars are found to kink sharply near their base, similar to the observed buckling near the base of CNT micropillars in compression. Upon reducing the flow rate, micropillars are found to fully recover from a near horizontal position to a near vertical position, even with repeated on-off cycling. At sufficiently high wall shear stress, the micropillars were found to detach at the catalyst particle-substrate interface. The mechanical response of CNT micropillars in airflow revealed by this study provides a basis for future development efforts and the accurate simulation of CNT micropillar wall shear stress sensors.

Study on the tribological behavior of TiN-VN/PAO composite lubricant system: ZIF-8 as a lubricating additive

Safety and reliability of mechanical systems are compromised by the lubricant degradation and excessive wear on contact surfaces. In response, a TiN-VN/PAO lubrication system was developed, and zeolitic imidazolate frameworks-8 (ZIF-8) nanoparticles with highly ordered pore structures were introduced to improve friction performance. The findings indicate that the addition of ZIF-8 significantly reduces the friction coefficient and wear rate in the composite system. The outstanding anti-friction performance is attributed to the heterogeneous TiN-VN nanolaminates material, which provides exceptional deformation tolerance and interface friction products. XPS analysis reveals the formation of a low shear strength Magnéli phases (V2O5) on the wear track surface, while TEM observations demonstrate that a ∼18 nm Zn-rich layer was developed at the interface, acting as a lubricating barrier layer.

Active polar ring polymer in shear flow-An analytical study.

We theoretically study the conformational and dynamical properties of semiflexible active polar ring polymers under linear shear flow. A ring is described as a continuous semiflexible Gaussian polymer with a tangential active force of a constant density along its contour. The linear but non-Hermitian equation of motion is solved using an eigenfunction expansion, which yields activity-independent, but shear-rate-dependent, relaxation times and activity-dependent frequencies. As a consequence, the ring's stationary-state properties are independent of activity, and its conformations and rheological properties are equal to those of a passive ring under shear. The presence of characteristic time scales by relaxation and the activity-dependent frequencies give rise to a particular dynamical behavior. A tank-treading-like motion emerges for long relaxation times and high activities, specifically for stiff rings. In the case of very flexible polymers, the relaxation behavior dominates over activity contributions suppressing tank-treading. Shear strongly affects the crossover from a tank-treading to a relaxation-dominated dynamics, and the ring polymer exhibits tumbling motion at high shear rates. This is reflected in the tumbling frequency, which displays two shear-rate dependent regimes, with an activity-dependent plateau at low shear rates followed by a power-law regime with increasing tumbling frequency for high shear rates.

Carcass and Meat Characteristics of Cull Heifers from Different Genetic Groups Fed Diets with Different Sources of Nonprotein Nitrogen in Confinement.

The aim of this study was to evaluate the effect of genetic groups and diets with different sources of nonprotein nitrogen (NPN) on the carcass and meat characteristics of beef heifers. The meat from 40 heifers (20 ½ Angus ½ Nellore (A × N) and 20 ½ Charolais ½ Nellore (L × N)), finished in feedlots, was used. The heifers were fed diets containing different sources of NPN-(1) a diet with livestock urea and protected urea (LPU) and (2) a diet with extruded urea (EU)-in a completely randomized design with a 2 × 2 factorial arrangement. Carcass, composition and meat quality evaluations were carried out. There were no significant interactions between diet and genetic group for most of the variables evaluated (p > 0.05). The A × N heifers had higher hot carcass weights (305.73 vs. 279.80 kg), loin eye areas (80.87 vs. 75.45 cm2), subcutaneous fat thicknesses (8.69 vs. 6.35 mm) and lower shear forces (6.98 vs. 7.7 kg) compared to the C × N heifers (p < 0.05). The meat from the A × N heifers had higher proportions of saturated fatty acids (49.41 vs. 47.95%), with no effects on the proportions of monounsaturated (47.57%) and polyunsaturated (4.01%) fatty acids. The A × N heifers had better carcass and meat characteristics, while the C × N heifers had meat and fat with better fatty acid profiles.

Zero-g wind tunnel experiments on planetesimal erosion

ABSTRACT Wind erosion thresholds for planetesimals in protoplanetary discs depend on particle size, cohesion, ambient gas pressure, and gravity. In the experiments reported here, we used a low pressure shear wind tunnel for the first time under real zero gravity. That is, we carried out the experiments in the drop tower in Bremen at $10^{-5} \text{g}$. In concert with earlier work, we confirm the applicability of a single semi-empirical equation to describe the threshold shear stress for wind erosion. It can be applied to calculations of unstable orbits of planetesimals and the dissolution of planetesimals passing through evolving planetary atmospheres.

Bed Roughness Incorporated Lift Force Formulation for Sediment Concentration Solutions

Within the field of sediment transport dynamics, there is an emphasis on the need for providing and improving simplified analytical solutions from which the findings can be extended upon. Typically, solutions have been developed from the understanding and incorporation of vertical velocity components/distribution; however, there remains opportunity for analytical enhancement. Under uniform open channel dilute sediment laden flow conditions, the type II concentration profile reflects the maximum concentration at a distance from the bed. To analytically depict the type II profile, it is essential to describe the vertical velocity components acting within the flow hydrodynamics. Yet, the impact of bed roughness on the vertical velocity distribution influencing a sediment particle has not been articulated. Hence, in this research, the impact of bed roughness is incorporated into the vertical velocity distribution to formulate the lift force acting upon a particle, to provide a sediment concentration solution. The proposed analytical vertical velocity distribution solution is validated against existing formulations, followed by the proposed sediment concentration being validated against existing solutions. Here, the results indicate that analytically incorporating the bed roughness alongside the secondary current induced vortices provides a lift force solution that can depict the type II concentration profile. Under relatively low shear velocity, increasing the sediment diameter allows for a clearer depiction of the near surface region and profile curvature. Furthermore, the proposed sediment concentration solution can accurately depict the near surface region, curvature of concentration, and maximum concentration under relatively large shear velocity data. Importantly, under conditions where both the shear velocity and sediment diameter are relatively large, the maximum concentration is captured with greater accuracy; however, the curvature of the profile and the near surface region accuracy are hindered. It is to be noted, that due to the formulation of the proposed velocity distribution the accuracy of the solution towards the bed decreases due to instability caused as the characteristic depth decreases to zero.

A biodegradable ZnFe2O4/PLLA electrospun fibers based longitudinal mode piezoelectric membrane for health monitoring

Recently, multifunctional sensors based on piezoelectric active film fabricated with environmental friendly materials is a nascent field which can address the growing concern of electronic waste. Nevertheless, frequently utilized poly(vinylidene fluoride) (PVDF) and poly(L-lactic acid) (PLLA) encounter challenges of limited biocompatibility and weak piezoelectricity with low shear piezoelectric coefficient (d14), respectively. Accordingly, a biodegradable piezoelectric sensor comprising of PLLA nanofiber blended with ZnFe2O4 nanoparticles was developed in this work. The ZnFe2O4 nanoparticles served as heterogeneous nucleation center leading to improved piezoelectric coefficient and output than pure PLLA due to more consistent orientation of CO dipoles. The ZnFe2O4/PLLA film exhibited significant performance improvement featured with 1.7-fold higher longitudinal piezoelectric coefficient (d33 ∼ 6.5 ± 0.3 pm/V), nearly 250 % boosting on the output voltage. The ZnFe2O4/PLLA piezoelectric sensor induced high sensitivity (2–10 N:0.55 V/N; 10–32 N:0.29 V/N) and excellent mechanical stability for 27,000 cycles. The results of the soil burial experiment demonstrate that the film can degrade by over 75 % within 90 days, confirming its excellent biodegradability. Moreover, the ZnFe2O4/PLLA nanofibers based piezoelectric sensor could serve as effective detection evidenced by different output signals of head motion, pulse and artery beating demonstrating its feasible application for health monitoring. Considering the characteristics of straightforward fabrication and readily accessible sustainable materials, the ZnFe2O4/PLLA sensor provides an appealing eco-friendly solution for self-powered flexible personal devices disregarding the need to dispose of electronic waste.

Mitigation of fouling with swirling flow induced in 3-D double-sided straight channel for printed circuit heat exchanger

Fouling should be considered in the design of a printed circuit heat exchanger (PCHE) for industrial applications. The swirling flow, which is known to mitigate fouling in heat exchangers, can incorporate this aspect; however, realizing these flow characteristics in compact heat exchangers such as PCHE is difficult. Thus, this study proposed a three-dimensional (3-D) designed PCHE channel. To induce swirling flow, it was designed to face two semicircular straight channels with angles such that the interaction between the mainstreams in different flow directions induced a swirling flow. Compared to conventional two-dimensional (2-D) PCHE channels (straight, zigzag, and airfoil channels), the swirling flow induced in the proposed 3-D PCHE channel uniformly increased the wall shear stress while minimizing flow separation or recirculation. This minimized the low wall shear stress that was more likely to be fouled. A comparative evaluation of the thermal-hydraulic performance of the investigated channels was conducted by comparing the volume goodness factors under the equal hydraulic diameter. The proposed 3-D channels exhibited the potential to mitigate fouling, as well as a thermal-hydraulic performance comparable to that of conventional 2-D PCHE channels. Therefore, the proposed 3-D channel can be suggested as an advanced PCHE design option for high thermal-hydraulic performance and mitigation of fouling. Furthermore, because the swirling flow is known to mitigate fouling in heat exchangers as well as the heat transfer deterioration of sCO2, a double-sided straight channel with swirling flow is expected to be competitive.

Analytical approximations of laminar flow states above a curved wall heated from below

An analytical framework is developed for estimating wall-bounded plane laminar flow states above curved walls subject to external shear and heating. The framework is applicable to arbitrary lower-wall geometries with arbitrary temperature prescriptions. The study relies on perturbation expansions of flow states with respect to the inverse of the dimensionless channel wavelength. Exact closed-form solutions are obtained for systems of perturbation equations up to the third order, which have the freedom to allow for any flow constraint. As an application of the analytical framework, we examine flow states above two specific instances of wall geometries with long channel wavelengths. The approximated flow states shed insights into morphologies of laminar convection states at low shear rates (i.e. low Reynolds numbers).

Shear deformation behavior of additively manufactured 316L stainless steel lattice structures

With the development of additive manufacturing, lattice structures have emerged as a disruptive technology across various fields, including aerospace, automotive, and defense. Lattice structures exhibit exceptional properties for lightweight and energy absorption capacities, especially under compressive loads. However, the lack of experimental data on complex loads, such as shear properties of lattice structures, poses challenges to their broader application across different load types. This study aims to analyze the shear deformation behavior of lattice structures and compare them with their compressive properties, enabling the safe design of lattice structures for various load applications. To achieve this, 316 L stainless steel lattice structures were fabricated using additive manufacturing in three different geometries: body-centered cubic (BCC), face-centered cubic (FCC), and octet truss (OCT), all at the same relative density. The lattice geometries were compared for their mechanical properties and deformation mechanisms under the two types of loading using DIC and FEM analyses, compression and shear tests. It was found that the mechanical properties of the lattice structures under compression and shear loads varied depending on the geometry, showing that each lattice geometry has a unique load-bearing capacity that exhibits superior mechanical properties. Furthermore, under shear loading, the struts of the BCC lattice structure showed a bending-dominated deformation mode due to the rotation of the nodes, whereas the struts of the FCC and OCT structures presented a compression and tension-dominated deformation mode. As a result, the BCC lattice specimens showed a higher shear energy absorption capacity than the other specimens and were capable of bearing higher loads. In addition, the FCC specimens showed lower shear energy absorption. The OCT specimens presented a uniform strain distribution under both compression and shear loading and showed compliant performance. The shear deformation behavior of various lattice structures has been evaluated by considering both geometrical and local strain distribution aspects. Implications for optimization guidelines and potential improvements were also discussed. These results can be used for research and development of the shear properties of lattice structures, the safe design of lattice structures, and industrial applications.

Origami Morphing Surfaces with Arrayed Quasi-Rigid-Foldable Polyhedrons.

Artificial morphing surfaces, inspired by the high adaptability of biological tissues, have emerged as a significant area of research in recent years. However, the practical applications of these surfaces, constructed from soft materials, are considerably limited due to their low shear stiffness. Rigid-foldable cylinders are anisotropic structures that exhibit high adaptability and shear stiffness. Thus, they have the potential to address this issue. However, changes in shape and area at both ends during folding can lead to collisions or gaps on the morphing surface. Here, a quasi-rigid-foldable (QRF)rate is first introduced to quantify the rigid-foldability of a foldable structure and validate it through experiments. More importantly, a QRF polyhedron is then proposed, which is not only notably anisotropic, similar to a rigid-foldable cylinder, but also exhibits a zero-Poisson's ratio property, making it suitable for arraying as morphing surfaces without any collisions or gaps. Such surfaces have a myriad of applications, including modulating electromagnetic waves, gripping fragile objects, and serving as soles for climbing robots.

Prediction of retrogressive landslide in sensitive clays by incorporating a novel strain softening law into the Material Point Method

Sensitive clays, when subjected to large strains, exhibit a unique strain-softening behavior, transforming into a remolded liquid with remarkably low shear strength. When a slope fails, this behavior leads to the remolded clay moving away from its original position, triggering subsequent failures and catastrophic outcomes. To accurately predict such scenarios, it is crucial to incorporate realistic strain-softening characteristics into the constitutive soil model. This paper presents a novel yet practical strain-softening law developed by the authors that effectively captures the post-peak behavior of sensitive clays down to their remolded strength. The softening law is implemented in an elastoplastic Mohr-Coulomb model and incorporated into Anura3D, an open-source software that uses the Material Point Method to simulate large deformations. The constitutive model is calibrated by simulating the stress-strain behavior through direct shear tests conducted at three sensitive clay landslide locations. The accuracy of the overall numerical framework is assessed by predicting the post-failure movements of these landslides. Notably, two of the landslides, Sainte-Monique (1994) and Saint-Jude (2010), have previously been analyzed using other numerical tools, allowing for a comparative analysis with the method presented here. The third landslide, the Saint-Luc-de-Vincennes landslide, representing a composite flow slide and spread, has been numerically simulated for the first time. The post-failure behavior observed in the landslide events is compared with field observations and other numerical analyses. The results show that the MPM models with the proposed strain-softening law can reasonably predict post-failure retrogression and runout distance, which are crucial parameters for determining the risk of landslides in sensitive clays.