Low Displacement Research Articles

The precision of signals encoding active self-movement.

Everyday actions like moving the head, walking around, and grasping objects are typically self-controlled. This presents a problem when studying the signals encoding such actions because active self-movement is difficult to control experimentally. Available techniques demand repeatable trials, but each action is unique, making it difficult to measure fundamental properties like psychophysical thresholds. We present a novel paradigm that recovers both precision and bias of self-movement signals with minimal constraint on the participant. The paradigm relies on linking image motion to previous self-movement, and two experimental phases to extract the signal encoding the latter. The paradigm takes care of a hidden source of external noise not previously accounted for in techniques that link display motion to self-movement in real time (e.g., virtual reality). We use head rotations as an example of self-movement, and show that the precision of the signals encoding head movement depends on whether they are being used to judge visual motion or auditory motion. We find that perceived motion is slowed during head movement in both cases. The "nonimage" signals encoding active head rotation (motor commands, proprioception, and vestibular cues) are therefore biased toward lower speeds and/or displacements. In a second experiment, we trained participants to rotate their heads at different rates and found that the imprecision of the head rotation signal rises proportionally with head speed (Weber's law). We discuss the findings in terms of the different motion cues used by vision and hearing, and the implications they have for Bayesian models of motion perception.NEW & NOTEWORTHY We present a psychophysical technique for measuring the precision of signals encoding active self-movements. Using head movements, we show that 1) precision is greater when active head rotation is performed using visual comparison stimuli versus auditory; 2) precision decreases with head speed (Weber's law); 3) perceived speed is lower during head rotation. The findings may reflect the steps needed to convert different cues into common units, and challenge standard Bayesian models of motion perception.

Finite Element Analysis of Prefabricated Semi-Rigid Concrete Beam–Column Joint with Steel Connections

This paper introduces a novel type of prefabricated semi-rigid concrete beam–column joint, aiming to examine its load-carrying capacity and seismic performance in comparison with a traditional cast-in-place joint. This study utilized the ABAQUS 2020 software to establish finite element models for both types of joints and conducted finite element analysis under low circumferential reciprocating displacement loads. When comparing the energy dissipation capacity, ductility, ultimate load-carrying capacity, stress mechanism, and damage mode, a comprehensive evaluation of the two types of joints was performed. Furthermore, this study investigated the impacts of various factors such as the axial compression ratio, concrete strength, reinforcement strength, and connector strength on the ultimate load-carrying capacity, ductility, and energy dissipation performance of the joints. Based on the findings, the newly combined joint exhibited a substantial 31.7% increase in its ultimate load-carrying capacity, along with a notable 7.23% enhancement in ductility and an improved energy dissipation capacity when compared with the cast-in-place joint. As a result, it can be concluded that the seismic performance of the new joint surpasses that of cast-in-place joints. Additionally, this study examined the impact of modifying relevant parameters on the seismic performance of the new prefabricated semi-rigid concrete beam–column joint.

Application of small punch test to estimate mechanical behaviour of SUS304 austenitic stainless steel

The small punch test with an application of a relatively small specimen has recently become a reliable material mechanics testing method. In this study, the small punch test is set up based on the conventional mechanical testing machine for SUS304 stainless steel to evaluate the mechanical properties of SUS304 steel at different displacement rates of the punch in quasi-static loading condition in the case of with and without heat treatment. Although heat treatment has an insignificant effect on the microstructure and hardness of the material, the mechanical properties of the material in the small punch test are greatly reduced after heat treatment. Both cases with and without heat treatment have a similar tendency for the rate - sensitivity of the applied force - displacement curve. A higher value of force is applied to obtain the same value of displacement at a low displacement rate in the stable plastic deformation zone. Meanwhile, the maximum value of applied force is higher at a higher displacement rate in the stage that initiation of crack might appear. In the examined range of displacement rate, a positive rate - sensitivity of displacement at the maximum force. Therefore, a correlation between equivalent fracture strain and fracture toughness of the material can be achieved.

A proof-of-concept study of ultrasound-guided continuous parasacral ischial plane block for postoperative pain control in patients undergoing total knee arthroplasty

BackgroundContinuous peripheral nerve blocks are widely used for anesthesia and postoperative analgesia in lower limb surgeries. The authors aimed to develop a novel continuous sacral plexus block procedure for analgesia during total knee arthroplasty.MethodsThe study comprised two stages. In Stage I, the authors built upon previous theories and technological innovations to develop a novel continuous sacral plexus block method, ultrasound-guided continuous parasacral ischial plane block (UGCPIPB) and subsequently conducted a proof-of-concept study to assess its effectiveness and feasibility. Stage II involved a historical control study to compare clinical outcomes between patients undergoing this new procedure and those receiving the conventional procedure.ResultsThe study observed a 90% success rate in catheter placement. On postoperative day (POD) 1, POD2, and POD3, the median visual analog scale (VAS) scores were 3 (range, 1.5–3.5), 2.5 (1.6–3.2), and 2.7 (1.3–3.4), respectively. Furthermore, 96.3% of the catheters remained in place until POD3, as confirmed by ultrasound. The study revealed a significant increase in skin temperature and peak systolic velocity of the anterior tibial artery on the blocked side compared with those on the non-blocked side. Complications included catheter clogging in one patient and leakage at the insertion site in two patients. In Stage II, the novel technique was found to be more successful than conventional techniques, with a lower catheter displacement rate than the conventional procedure for continuous sciatic nerve block.ConclusionUGCPIPB proved to be an effective procedure and safe for analgesia in total knee arthroplasty.Chinese Clinical Trial Registry NumberChiCTR2300068902.

Biomechanical comparison of a new undercut thread design vs the V-shape thread design for pedicle screws

BACKGROUND CONTEXTThread shape is regarded as an important factor influencing the fixation strength and osseointegration of bone screws. However, commercial pedicle screws with a V-shaped thread are prone to generating stress concentration at the bone-screw interface, thereby increasing the risk of screw loosening. Thus, modification of the pedicle-screw thread is imperative. PURPOSEThis study aimed to investigate the fixation stability of pedicle screws with the new undercut thread design in comparison to pedicle screws with a V-shaped thread. STUDY DESIGNIn vitro cadaveric biomechanical test and finite element analysis (FEA). METHODSPedicle screws with the undercut thread (characterized by a flat crest feature and a tip-facing undercut feature) were custom-manufactured, whereas those with the V-shaped thread were procured from a commercial supplier. Fixation stability was assessed by the cyclic nonpullout compressive biomechanical testing on cadaveric female osteoporotic vertebrae. The vertical displacement and rotation angle of the 2 types of pedicle screws were calculated every 100 cycles to evaluate their resistance to migration and rotation. FEA was conducted to investigate the stress distribution and bone damage at the bone-screw interface for both types of pedicle screws. RESULTSBiomechanical testing revealed that the pedicle screws with the undercut thread exhibited significantly lower vertical displacement and rotation angles than the pedicle screws with the V-shape thread (p<0.05). FEA results demonstrated a more uniform stress distribution in the bone surrounding the thread in the undercut design than in the V-shape design. Additionally, bone damage resulting from the pedicle screw was lower in the undercut design than in the V-shape design. CONCLUSIONSPedicle screws with an undercut thread are less prone to migration and rotation and thus more stable in the bone than those with a V-shape thread. CLINICAL SIGNIFICANCEThe undercut thread design may reduce the incidence of pedicle-screw loosening.

Efficacy and safety of video double-lumen tube intubation in lateral position in patients undergoing thoracic surgery: a randomized controlled trial

BackgroundVideo double-lumen tube (VDLT) intubation in lateral position is a potential alternative to intubation in supine position in patients undergoing thoracic surgery. This non-inferiority trial assessed the efficacy and safety of VDLT intubation in lateral position.MethodsPatients (18–70 yr) undergoing right thoracoscopic lung surgery were randomized to either the left lateral position group (group L) or the supine position group (group S). The VDLT was placed under video larygoscopy. The primary endpoint was the intubation time. Secondary endpoints included VDLT displacement rate, intubation failure rate, the satisfaction of surgeon and nurse, and intubation-related adverse events.ResultsThe analysis covered 80 patients. The total intubation time was 52.0 [20.4]s in group L and 34.3 [13.2]s in group S, with a mean difference of 17.6 s [95% confidence interval (CI): 9.9 s to 25.3 s; P = 0.050], failing to demonstrate non-inferiority with a non-inferiority margin of 10 s. Group L, compared with group S, had significantly lower VDLT displacement rate (P = 0.017) and higher nurse satisfaction (P = 0.026). No intubation failure occurred in any group. Intubation complications (P = 0.802) and surgeon satisfaction (P = 0.415) were comparable between two groups.ConclusionsThe lateral VDLT intubation took longer time than in the supine position, and non-inferiority was not achieved. The incidence of displacement as the secondary endpoint was lower in the L group, possibly due to changing body positions beforehand. The indication of lateral VDLT intubation should be based on a balance between the safety of airway management and the lower incidence of displacement.Trial registrationThe study was registered at Chictr.org.cn with the number ChiCTR2200064831 on 19/10/2022.

Therapeutic dosage of isotretinoin in rats may influence orthodontic tooth movement

Objective Isotretinoin, also known as 13-cis-retinoic acid, is an isomer of tretinoin, the oxidized form of Vitamin A. Orthodontic tooth movement (OTM) is the result of a cascade of inflammatory responses stimulated by a physical element that is the force generated by orthodontic appliances. Isotretinoin is mainly used among adolescents and young adults, and coincidentally it is this age group that also undergoes orthodontic treatment. Materials and Methods Fifty-five animals were used, and they were randomly divided into 11 groups, containing 5 animals in each group. Group 1: Control; Group 2: OTM for 7 days; Group 3: OTM for 14 days; Group 4: Treated with isotretinoin for 14 days with a dosage of 7.5 mg/kg/day; Group 5: Treated with isotretinoin for 14 days with a dosage of 1.0 mg/kg/day; Group 6: Treated with isotretinoin for 21 days with a dosage of 7.5 mg/kg/day; Group 7: Treated with isotretinoin for 21 days with a dosage of 1.0 mg/kg/day; Group 8: Treated with isotretinoin for 14 days with a dosage of 7.5 mg/kg/day and undergoing OTM for 7 days; Group 9: Treated with isotretinoin for 14 days with a dosage of 1.0 mg/kg/day and undergoing OTM for 7 days; Group 10: Treated with isotretinoin for 21 days with a dosage of 7.5 mg/kg/day and undergoing OTM for 14 days; Group 11: Treated with isotretinoin for 21 days with a dosage of 1.0 mg/kg/day and undergoing OTM for 14 days. In Groups 8, 9, 10 and 11, the animals were treated with isotretinoin for 7 days before OTM and maintained during the movement period in the respective groups.Results There was a significant difference in microtomographic parameters, including Trabecular Volume (BV/TV), Trabecular Thickness (Tb.Th), Number of Trabeculae (Tb.N), and Trabecular Separation (Tb.Sp), between the groups. The group that received orthodontic force in conjunction with isotretinoin treatment at a dosage of 7.5 mg/kg/day exhibited lower tooth displacement over a period of 21 days and 14 days. Conclusion Isotretinoin caused a reduction in tooth displacement during OTM when administered at a dose of 7.5 mg/kg/day and isotretinoin did change the microtomographic parameters of treated animals.

Data fusion based on short-term memory Kalman filtering using intermittent-displacement and acceleration signal with a time-varying bias

Accurate displacement information plays a vital role in various applications from structural health monitoring to damage detection in physical systems. Due to practical reasons, displacement sensing is often performed using sensors that provide less accuracy or a low sampling rate. This study proposes an algorithm for displacement signal estimation that fuses high sampling rate acceleration data (which consists of unknown time-varying bias) with low sampling rate displacement data. In contrast to the present literature, the state vector in the proposed state-space formulation consists of short-term memory of the past realizations of displacement and velocity, and bias terms which allow (i) online estimation of the displacements by avoiding multi-rate Kalman filtering, and (ii) estimate time-varying bias in the measured acceleration signal. The state equations comprise the finite difference approximations of the time derivative of velocity and displacement which act as a moving average filter to provide smooth estimates, thus preventing the need for offline smoothing procedures. By inclusion of bias terms in the state vector, the drifts in displacement and velocity caused due to time-varying bias in measured acceleration are easily eliminated. The proposed method was found to provide accurate estimates of displacement, velocity, and time-varying bias in measured acceleration signals when tested on different types of bias, including but not limited to constant, linear, and parabolic variations. Additional tests on three oscillators subjected to three earthquake ground motions showed significantly better state estimates for stiff oscillators and improved estimates for flexible oscillators. Experimental validation on a base-excited two-story frame further affirms the capability of the method to estimate the hidden bias in the measured acceleration and provide an accurate estimate of displacement.

Parametric Dynamic Simulation and Bayesian Design Optimization of a Front-Loading Washing Machine

Abstract Objective This paper presents the dynamic modeling and design optimization of a fully parametrized front-loading washing machine. Methods A thorough mathematical analysis is performed to capture the effect of nine design variables (including rotation speed, spring stiffness, weight balancer mass density, damping coefficient, spring and damper angles) on vibrational characteristics of the washing machine. The parametric simulation reveals a complex relationship between the vibrational dynamics and design variables, entailing a computationally efficient optimization approach. A Bayesian Optimization (BO) framework is developed, in which a Gaussian process model and Genetic Algorithm (GA) are utilized along with carefully selected acquisition functions to enable adaptive sampling and search for optimal design values. The objective function is to minimize the maximum amplitude of the tub displacement inside the washing machine body. Two case studies are performed to consider a different number of design variables and choices of various infill methods. Results Results show that the fully parametrized front-loading washing machine model is applicable for parametric simulation and design optimization. The proposed BO is able to successfully find a set of design variable values corresponding to the lowest maximum displacement for vibration reduction. A comparison analysis is also carried out to exhibit the difference in optimization convergence and computational cost caused by the choice of acquisition functions. Conclusion It is shown that the fully parametrized washing machine model yields a lower maximum displacement than the model with fewer design variables. Of the two acquisition functions studied for optimization, the Expected Improvement function converges more rapidly than the Lower Bound criterion.

Comparison of the biomechanical behavior between commercial and 3D-printed patient-specific Ti6Al4V L-Shaped titanium plates following le fort i osteotomy using finite element analysis: A technical Note

ObjectiveTo evaluate and compare the biomechanical behavior of three-dimensionally (3D) printed patient-specific Ti6Al4V with commercially made titanium mini plates following Lefort-I osteotomy using finite element analysis. MethodsLe Fort I osteotomy was virtually simulated with a 5 mm maxillary advancement and mediolateral rotation in the coronal plane, resulting in a 3 mm gap on the left side's posterior. Two fixation methods were modeled using software to compare 3D-printed Ti6Al4V and commercial titanium mini plates, both featuring a 4-hole l-shape with thicknesses of 0.5 mm and 0.7 mm at the strategic piriform rim and zygomaticomaxillary buttress locations. Using ANSYS R19.2, finite element models were developed to assess the fixation plates and maxilla's stress, strain, and displacement responses under occlusal forces of 125, 250, and 500 N/mm². ResultsThis comparative analysis revealed slight variation in stress, strain, and displacement between the two models under varying loading conditions. Stress analysis indicated maximum stress concentrations at the vertical change in the left posterior area between maxillary segments, with the Ti6Al4V model exhibiting slightly higher stress values (187 MPa, 375 MPa, and 750 MPa) compared to the commercial titanium model (175 MPa, 351 MPa, and 702 MPa). Strain analysis showed that the commercial titanium model recorded higher strain values at the bending area of the l-shaped miniplate. Moreover, displacement analysis revealed a maximum of 3 mm in the left posterior maxilla, with the Ti6Al4V model demonstrating slightly lower displacement values under equivalent forces. ConclusionThe maximum stress, strain, and segment displacement of both fixation models were predominantly concentrated in the area of the gap between the maxillary segments. Notably, both fixation models exhibited remarkably close values, which can be attributed to the similar design of the fixation plates.

Seismic evaluation of a self-centering retrofit solution for modular steel structure connections

In this study, a novel plug-in modular steel structure (MSS) connection is proposed, in which the connector, cover plates, and bolts form a complete connecting system. To improve the seismic performance and post-earthquake functional recoverability of the MSS connection, a retrofit solution with diagonal self-centering (SC) haunch braces is introduced, and the self-centering modular steel structure (SC-MSS) connection is developed. Theoretical analysis of the mechanical properties of the MSS and SC-MSS connections are conducted, and the calculation formulas for the initial stiffness and bending bearing capacity are derived. A comparative experimental study of one MSS connection and five SC-MSS connections under cyclic loading was carried out to evaluate their seismic performance, and to explore the influences of the main haunch parameters on the behavior of the SC-MSS connection. The results demonstrate that the plug-in connector, cover plate, and bolts can realize reliable continuity and integrity between modules. The SC haunch braces have good collaborative work with the modules and provide sufficient restoring force, and the damage in all the SC-MSS connections was found to be effectively controlled and delayed as compared with the MSS connection. The MSS connection displays a full shuttle-shaped hysteretic response with adequate plastic development, while the SC-MSS connections successfully exhibit expected flag-shaped hysteretic responses with higher bearing capacity and lower residual displacement. The adjustment of the post-activation stiffness and pre-pressed force of the haunch brace is found to improve the connection performance, and a reasonable selection of the installation scheme could achieve optimal self-centering efficiency. The experimental results also verify the feasibility and correctness of the proposed theoretical formulas and mechanical assumptions.

Comparative impact behaviours of ultra high performance concrete columns reinforced with polypropylene vs steel fibres

Polypropylene (PP) fibres have primarily used to control shrinkage cracks or mitigate explosive spalling in concrete structures exposed to fire or subjected to impact/blast loads, with limited investigations on capacity improvement. This study unveils the possibility of using PP micro-fibres to improve the impact behaviour of fibre-reinforced ultra-high-performance concrete (FRUHPC) columns. Results show that the addition of fibres significantly improves the impact behaviour of FRUHPC columns by shifting the failure mechanism from brittle shear to favourable flexural failure. The addition of steel or PP fibres affected the impact responses differently. Steel fibres considerably increased the peak impact force (up to 18%) while PP micro-fibres slightly increased the peak (3%–4%). FRUHPC significantly reduced the maximum mid-height displacement by up to 30% (under 20° impact) and substantially improved the displacement recovery by up to 100% (under 20° impact). FRUHPC with steel fibres significantly improved the energy absorption while those with PP micro-fibres reduced the energy absorption, which is different from the effect of PP-macro fibre reported in the literature. The optimal fibre content for micro-PP fibres is 1% due to its minimal fibre usage and low peak and residual displacement. This study highlights the potential of FRUHPC as a promising material for impact-resistant structures by creating a more favourable flexural failure mechanism, enhancing ductility and toughness under impact loading, and advancing the understanding of the role of fibres in structural performance.

A Comprehensive Evaluation of Tuned Vertical Isolation System for Seismic Risk Mitigation

Abstract Vertical isolation by dividing the building into two soft and stiff sub-systems benefits from the period shifts and the damping mechanism across the height. However, the displacement demand imposed on the soft sub-system is less applicable in congested urban areas. As a result, in this study, a hybrid system of vertical isolation system benefiting from a tuned soft subsystem divided into upper and lower portions is investigated. A parametric linear 3-Degree of Freedom (DoF) model of the system incorporating mass and frequency ratio of the sub-systems was introduced and analyzed by response spectrum in MATLAB. A closed-form solution for the system frequency and mode shapes was also established. Response spectrum analysis indicates increasing the Tuned Mass Damper (TMD)’s fundamental period to 2.5 times the soft sub-system’s, reduces its displacement to more than 40 percent. The Multi Degree of Freedom (MDoF) model of the system is parametrically generated in MATLAB. Time history analysis of the building subjected to 40 records with 2 and 10 percent probabilities of exceedance in 50 years compared with conventional vertical isolation reveals the lower soft sub-system displacement can be reduced up to 45 percent by shifting drift to upper stories. The innovative tuned vertical isolation by demonstrating superior control performance as comprises lower floors’ drift may be an applicable solution for adjacent high- and low-rise buildings.

Comparative Study of G+6 Irregular Multistoryed Building of Different Shape of Diaphragm

Abstract: This study investigates the effectiveness of incorporating openings in the roof of re-entrant corner plan irregular buildings at different locations under earthquake loads. Five models with varying degrees of diaphragm discontinuity were analysed using STAAD Pro software. Node displacement, storey shear in X and Z directions, stress values, and maximum bending moment were evaluated to assess structural performance. Results indicate that models with higher diaphragm discontinuity exhibit increased node displacements, storey shear, and stress levels. Model M3, with 17% diaphragm discontinuity, consistently demonstrates superior performance in terms of lower displacements and stress values compared to other models. However, final model selection should consider specific project requirements and design considerations.

Comparative Study of G+6 Irregular Multistoryed Building of L Shape of Diaphragm Discontinuity

Abstract: This study investigates the effectiveness of incorporating roof openings in re-entrant corner plan irregular buildings at various locations under earthquake loads. Three models L-shaped diaphragm discontinuity were analyzed using STAAD Pro software. Node displacement and storey shear in both the X and Z directions were evaluated to assess structural performance. The results indicate that models with square diaphragm discontinuity exhibit increased node displacements and storey shear compared to those with L-shaped diaphragm discontinuity. The model with L-shaped diaphragm discontinuity consistently demonstrates superior performance in terms of lower displacements and shear stress values. However, the final model selection should take into account specific project requirements and design considerations.

Cross-sectional shape effect of stay-in-place formwork column on axial compressive behaviour

Experimental and numerical studies on the behavior of composite columns with prefabricated self-compacting mortar (SCM) stay-in-place (SIP) formwork and post-cast normal-strength core concrete were presented.The axial compression of twenty-eight reinforcement concrete (RC) composite columns having square or circular cross-section shapes, with formwork thicknesses of 10 mm or 15 mm, and confined with one or two layers of Carbon Fibre Reinforced Polymer (CFRP (, were tested. A finite element (FE) model was generated to simulate the stress–strain relationship, and failure mode of the column using ABAQUS software. The results show that square cross-section-shaped columns exhibited lower axial load and displacement capacities than their counterparts of equivalent circular cross-section-shaped columns. This behavior maintained consistent regardless of the use of the SCM-SIP formworks or the wrapping with CFRP fabrics. Among the various confinement systems compared in this study, the efficiency of the CFRP was the greatest. Good bonding with no peeling failure was observed between SCM-SIP formwork and core concrete, indicating the good integrity of the composite columns. Consistency between the FE model and experimental results was observed for both cross-section shapes, indicating the precise and plausible characteristics of the model to sensibly estimate the stress-strain behaviors.

Integrated analysis of wireline logs analysis, seismic interpretation, and machine learning for reservoir characterisation: Insights from the late Eocene McKee Formation, onshore Taranaki Basin, New Zealand

This study aims to integrate seismic and well data for re-assessment and delineating the geological and petrophysical characteristics of the Late Eocene McKee Formation. Despite the McKee Formation being a hydrocarbon-producing field, there have been no previous integrated studies conducted to characterize its deposits in the Taranaki Basin. To execute these tasks, the process involves the interpretation of seismic data, wireline analysis, and 3D porosity volume prediction using multi-layered feed-forward neural network models. The seismic data was interpreted and found to contain low displacement faults due to intricate geometric complexities, the contour map that was generated shows lateral extension and thickness variation, and the region of direct hydrocarbon indicators was detected using the root-mean-square. Additionally, the seismic inversion provides a comprehensive understanding of the acoustic impedance variations from low to high value, which signifies the presence of mudstone clasts content. Furthermore, in the wireline log analysis, the reservoir was found to be a Silici-clastic and carbonate field owing to the presence of dolomite, calcite, and quartz. After applying cutoffs, petrophysical parameters were evaluated. The estimated values for effective porosity, reservoir thickness, shale volume, and water and hydrocarbon saturation were 15.04 % to 17.29 %, 85.44 m to 122.41 m, 8.99 to 14.87 % and 12.97–27.10 %, and 72.9 % to 87.03 %, respectively. The outcome of this extensive research aids in accurately characterizing this region for the future prospectively of the field. This integrated study can be applied and adapted to other basins in New Zealand and the southwestern Pacific. The proposed workflow is also suitable for analogous scenarios in various basins worldwide.

Ultrasound imaging of core muscles activity in multiparous women with vaginal laxity: a cross-sectional study

Vaginal laxity (VL) is a common condition among multiparous women, especially those who have delivered vaginally. Since pelvic floor muscles (PFMs) work synergistically with other core muscles, physical therapy protocols that aim to treat VL should train the PFMs in combination with other core muscles. To investigate the activity of core muscles in multiparous women with and without VL, and its relation to sexual function. An observational, cross-sectional study. The study included 100 multiparous women, who were divided into two groups according to their scores on the vaginal laxity questionnaire (VLQ). Women who scored between 1 and 3 on the VLQ were categorized as having VL (n = 48), while those who scored between 5 and 7 were placed in the control group (n = 52). The primary outcomes were PFM displacement, diaphragmatic excursion, transversus abdominis activation ratio, and lumbar multifidus thickness measured by ultrasound imaging. The secondary outcome was sexual functioning, evaluated using the Arabic female sexual function index (ArFSFI). The VL group had significantly lower PFM displacement (mean difference (MD) − 0.42; 95% confidence interval (CI) − 0.49 to − 0.33; p = 0.001), diaphragmatic excursion (MD − 2.75; 95% CI − 2.95 to − 2.55; p = 0.001), lumbar multifidus thickness (MD − 10.08; 95% CI − 14.32 to − 5.82; p = 0.02), and ArFSFI scores (MD − 9.2; 95% CI − 10.59 to − 7.81; p = 0.001) in comparison to the control group (p < 0.05). Nevertheless, the transversus abdominis activation ratio demonstrated no significant difference between the two groups (MD 0.06; 95% CI − 0.05 to 0.17; p = 0.33). Multiparous women with VL had significantly lower PFM displacement, diaphragmatic excursion, lumbar multifidus thickness, and sexual function index scores than women in the control group. The only exception was transversus abdominis activation, which did not differ significantly between the VL and control groups.

The effectiveness of Q6 and PIPER 6-year-old models on quantification of the change of child sitting posture with AEB and its impact on child’s injures in frontal crash

Objective Automatic Emergency Braking (AEB) has a direct impact on the effectiveness of the restraint systems in providing protection toward child occupants. The objective is to evaluate the effectiveness of Q6 and PIPER 6-year-old models in predicting the kinematic responses of child models, and further to quantify and analyze the child injuries during a frontal crash with and without AEB. Methods The finite element model of a booster seat has been validated through a full vehicle test. Based on the validated finite element model, two sled test finite element models for the rear seat booster seat with Q6 and PIPER 6-year-old models were constructed. AEB condition was imposed on above the two models and the kinematic responses of sitting posture including head, neck and chest have been compared in detail. The peak head displacement and neck curvature of Q6 dummy and PIPER 6-year-old models have been compared with the test data from child volunteers. Based on the child model with better predictive capability for kinematic response under AEB, child injuries were evaluated and analyzed for the 50 km/h frontal crash test with and without AEB. Last, this study discussed the effects of internal neck and chest structure difference between Q6 and PIPER 6-year-old models on child kinematic response and the injury risks. Results Under AEB condition, PIPER 6-year-old model has higher head displacement and lower trunk displacement than Q6 dummy model, and the peak head displacement and neck curvature of PIPER 6-year-old model are similar to the test data of child volunteers. During the 50 km/h frontal crash simulation with pre-crash AEB, the HIC15, Head acceleration 3 ms, Nij decrease 43.7%, 19.6% and 28.8%, respectively and the chest deflection increases 15.5% compared to the simulation without AEB. Conclusions This study shows that PIPER 6-year-old model is more suitable for the quantification of sitting posture change under AEB due to its higher biofidelity. The pre-crash AEB can substantially reduce the head, neck injuries. But it also increases the chest injury due to the chest pre-compression. Future efforts are recommended to lower the child chest injury by integrating AEB with active pre-tensioning seatbelts.

Enhanced high-frequency piezoelectric ultrasonic transducer based on integrated AlN honeycomb structure

Ultrasonic transducers are vital components for transmitting and receiving sound waves, which are customized to specific applications based on their operating frequencies.Small-sized high-frequency ultrasonic transducers have gained considerable attention and adoption in medical ultrasound imaging and small pipe flow testing. However, the significant impact of attenuation on high-frequency ultrasound restricts detection distance and degrades the signal-to-noise ratio. Additionally, thin-film high-frequency ultrasound transducers exhibit low output sound pressure, due to their low resonance displacement. In this study, we present an innovative approach to address these challenges through the design of an integrated small-size honeycomb-type top, two-electrode aluminum nitride (AIN)-based high-frequency ultrasonic transducer. A comprehensive investigation of the relationship between transducer size, sensitivity, and transmitted sound pressure levels is conducted. Leveraging microelectromechanical systems (MEMS) micro-nano-machining technology, we fabricate a 14 × 13 array with a unit diameter of 50 µm, and a matching circuit is employed to enhance the transducer's amplitude. Experimental results demonstrate remarkable transmit sound pressure levels (SPL) exceeding 210 dB (re:1 µPa/V) at a distance of 2 cm, with a maximum transmit SPL of 233 dB, and the receive sensitivity surpasses − 175 dB (re:1 V/µPa) and, at the 5 MHz resonance, the sensitivity reaches − 143 dB (re:1 V/µPa). Moreover, the transmit and receive linearity values demonstrate 99% and 98%, respectively. Our findings highlight the significant potential of the proposed high-frequency ultrasonic transducer for a diverse range of applications.