Low-coordinated Sites Research Articles

Effect of crystal facets in plasmonic catalysis

While the role of crystal facets is well known in traditional heterogeneous catalysis, this effect has not yet been thoroughly studied in plasmon-assisted catalysis, where attention has primarily focused on plasmon-derived mechanisms. Here, we investigate plasmon-assisted electrocatalytic CO2 reduction using different shapes of plasmonic Au nanoparticles - nanocube (NC), rhombic dodecahedron (RD), and octahedron (OC) - exposing {100}, {110}, and {111} facets, respectively. Upon plasmon excitation, Au OCs doubled CO Faradaic efficiency (FECO) and tripled CO partial current density (jCO) compared to a dark condition, with NCs also improving under illumination. In contrast, Au RDs maintained consistent performance irrespective of light exposure, suggesting minimal influence of light on the reaction. Temperature experiments ruled out heat as the main factor to explain such differences. Atomistic simulations and electromagnetic modeling revealed higher hot carrier abundance and electric field enhancement on Au OCs and NCs than RDs. These effects now dominate the reaction landscape over the crystal facets, thus shifting the reaction sites when comparing dark and plasmon-activated processes. Plasmon-assisted H2 evolution reaction experiments also support these findings. The dominance of low-coordinated sites over facets in plasmonic catalysis suggests key insights for designing efficient photocatalysts for energy conversion and carbon neutralization.

Identification of the active sites for CO2 methanation over Re/TiO2 catalysts

CO2 methanation on heterogeneous catalysts holds great significance in achieving the net-zero emission target. However, understanding the atomic-scale relationship between reactivity and active site has been a subject of debate. The study investigated CO2 methanation reaction catalyzed by Re/TiO2 catalysts and identified the active site distribution and its relationship with reactivity. The low-coordinated edge sites of Re nanoparticle were found to be the active sites where CO2 dissociated into CO via a carbide pathway and subsequently hydrogenated to form methane. Furthermore, the study revealed that the size of Re nanoparticle influenced the distribution of active edge sites and affected the reactivity and stability of the CO intermediate, which was the rate-determining step in CO2 methanation reaction. Controlling the size and structure of Re nanoparticle can, therefore, enhanced the activity and efficiency of CO2 methanation reaction. The identification of these active sites and the insights gained from this study have significant implications for the mechanistic understanding and optimization of CO2 methanation over Re/TiO2 catalysts. It provides a basis for designing more effective catalysts to facilitate the conversion of CO2 to methane, thereby contributing to the goal of achieving net-zero emissions.

Self-Limited Formation of Cobalt Nanoparticles for Spontaneous Hydrogen Production through Hydrazine Electrooxidation.

Hydrogen (H2 ) has emerged as a highly promising energy carrier owing to its remarkable energy density and carbon emission-free properties. However, the widespread application of H2 fuel has been limited by the difficulty of storage. In this work, spontaneous electrochemical hydrogen production is demonstrated using hydrazine (N2 H4 ) as a liquid hydrogen storage medium and enabled by a highly active Co catalyst for hydrazine electrooxidation reaction (HzOR). The HzOR electrocatalyst is developed by a self-limited growth of Co nanoparticles from a Co-based zeolitic imidazolate framework (ZIF), exhibiting abundant defective surface atoms as active sites for HzOR. Notably, these self-limited Co nanoparticles exhibit remarkable HzOR activity with a negative working potential of -0.1V (at 10mA cm-2 ) in 0.1m N2 H4 /1m KOH electrolyte. Density functional theory (DFT) calculations are employed to validate the superior performance of low-coordinated Co active sites in facilitating HzOR. By taking advantage of the potential difference between HzOR and the hydrogen evolution reaction (HER), a novel HzOR||HER electrochemical system is developed to spontaneously produce H2 without external energy input. Overall, the work offers valuable guidance for developing active HzOR catalyst. The novel HzOR||HER electrochemical system represents a promising and innovative solution for energy-efficient hydrogen production.

Low-coordinated Co-Mn diatomic sites derived from metal-organic framework nanorod promote electrocatalytic CO2 reduction

The manipulation of the geometric coordination structure of diatomic site (DS) catalysts to promote the CO2-to-CO conversion process has garnered significant attention. However, the challenge remains in how to rationally...

Construction of Low-Coordination Cu-C2 Single-Atoms Electrocatalyst Facilitating the Efficient Electrochemical CO2 Reduction to Methane.

Constructing Cu single-atoms (SAs) catalysts is considered as one of the most effective strategies to enhance the performance of electrochemical reduction of CO2 (e-CO2 RR) towards CH4 , however there are challenges with activity, selectivity, and a cumbersome fabrication process. Herein, by virtue of the meta-position structure of alkynyl in 1,3,5-triethynylbenzene and the interaction between Cu and -C≡C-, a Cu SAs electrocatalyst (Cu-SAs/HGDY), containing low-coordination Cu-C2 active sites, was synthesized through a simple and efficient one-step method. Notably, this represents the first achievement of preparing Cu SAs catalysts with Cu-C2 coordination structure, which exhibited high CO2 -to-CH4 selectivity (72.1 %) with a high CH4 partial current density of 230.7 mA cm-2 , and a turnover frequency as high as 2756 h-1 , dramatically outperforming currently reported catalysts. Comprehensive experiments and calculations verified the low-coordination Cu-C2 structure not only endowed the Cu SAs center more positive electricity but also promoted the formation of H•, which contributed to the outstanding e-CO2 RR to CH4 electrocatalytic performance of Cu-SAs/HGDY. Our work provides a novel H⋅-transferring mechanism for e-CO2 RR to CH4 and offers a protocol for the preparation of two-coordinated Cu SAs catalysts.

Valorization to hydrogen of bio-oil aqueous fractions from lignocellulosic biomass pyrolysis by aqueous phase reforming over Pt/C catalyst

Aqueous phase reforming was studied for the valorization to hydrogen of the aqueous fraction of bio-oil from lignocellulosic biomass pyrolysis. Aqueous phase reforming was carried out at 220 °C with a 3 % wt. Pt/carbon catalyst and an aqueous fraction of bio-oil feed containing 1 % wt. of organic matter. Binary and multicomponent mixtures representing aqueous fractions of bio-oil were studied. Strong hydrogen production dependence on aqueous fraction of bio-oil composition was evidenced. Higher processability was obtained for aqueous fractions of bio-oil rich in levoglucosan and hydroxyacetone, reaching a hydrogen production close to 40 mmol per gram of organic carbon, whereas furfural and acetic acid hampered reforming. A significant influence of minority components such as methanol and, particularly, formic acid, was observed. These components improved reforming of the whole multicomponent mixture, showing that blending with biorefinery fractions rich in them can improve the applicability of aqueous phase reforming. The catalyst exhibited stable activity and hydrogen production after 5 reaction cycles and more than 20 h. An increase in selectivity was observed during cycles 2 and 3, which was studied by characterization of fresh and used catalysts to show structure-selectivity relationships. No significant variation of Pt2+/Pt0 and metal particle mean diameter were observed, but Pt nanoparticles underwent morphological changes leading to higher prevalence of low coordination sites, in particular step-edge sites on the particle surface, resulting in higher hydrogen production. Temperature programmed desorption and oxidation analysis showed a cumulative deposition of reaction byproducts on the catalyst surface that contributed to loss of activity.

High or Low Coordination: Insight into the Active Site of Pt Nanoparticles toward CO Oxidation.

The catalytic activity of metal nanoparticles (NPs) is highly dependent on the coordination environment of the surface sites. Understanding the role of different sites in reactions is essential for gaining insights into catalytic activity and the precise design of catalysts. Herein, we used first-principles calculation-based kinetic Monte Carlo simulations to investigate correlations between different sites on Pt NPs in CO oxidation reactions. Low-coordinated (LC) sites favor the CO adsorption and reaction, whereas the oxygen mainly adsorbs on high-coordinated (HC) sites and diffuses to LC sites for reaction at low temperatures. Compared with step-dominated and terrace-dominated structures, the step-terrace structures exhibit higher activities. This reveals that the catalytic performance is not simply determined by the sites where the reaction occurs but is dramatically affected by the kinetic synergies between different sites. A proper way to optimize the activity of Pt catalysts is to balance the LC and HC sites.

The Role of Grain Boundary Sites for the Oxidation of Copper Catalysts during the CO Oxidation Reaction.

The oxidation of transition metal surfaces is a process that takes place readily at ambient conditions and that, depending on the specific catalytic reaction at hand, can either boost or hamper activity and selectivity. Cu catalysts are no exception in this respect since they exhibit different oxidation states for which contradicting activities have been reported, as, for example, in the catalytic oxidation of CO. Here, we investigate the impact of low-coordination sites on nanofabricated Cu nanoparticles with engineered grain boundaries on the oxidation of the Cu surface under CO oxidation reaction conditions. Combining multiplexed in situ single particle plasmonic nanoimaging, ex situ transmission electron microscopy imaging, and density functional theory calculations reveals a distinct dependence of particle oxidation rate on grain boundary density. Additionally, we found that the oxide predominantly nucleates at grain boundary-surface intersections, which leads to nonuniform oxide growth that suppresses Kirkendall-void formation. The oxide nucleation rate on Cu metal catalysts was revealed to be an interplay of surface coordination and CO oxidation behavior, with low coordination favoring Cu oxidation and high coordination favoring CO oxidation. These findings explain the observed single particle-specific onset of Cu oxidation as being the consequence of the individual particle grain structure and provide an explanation for widely distributed activity states of particles in catalyst bed ensembles.

Low-coordination transition metal sites on oxygen vacancy enriched strontium titanate-based perovskites enable highly selective photocatalytic CO2 reduction to CH4

The photochemical conversion of CO2 into high-value single hydrocarbon fuels such as CH4 remains a challenge. Here we have prepared a series of perovskites VO-SrTiMO3 (M = Mn, Fe, Co) with rich oxygen vacancies. Among them, Mn-doped perovskite (VO-STMn0.2) exhibited 18.21 μmol g−1 yield and nearly 100 % selectivity for CH4, as well as excellent reproducibility of about 15 h. Through a combination of advanced characterization and theoretical calculations, we found that the low-coordination transition metal site was able to stabilize the critical COOH* and CO* intermediates, thereby altering the reaction pathway to form CH4 instead of CO. Most importantly, this work demonstrated that the relative center between the 2p orbitals of the oxygen atom of the CO2 reduction intermediate and the 3d orbitals of the low-coordination metal site regulates the reaction mechanism of CO2 reduction, offering the possibility of achieving efficient photochemical reduction of CO2.

Nanoscale Oxygenous Heterogeneity in FePC Glass for Highly Efficient and Reusable Catalytic Performance.

Metallic glass, with its unique disordered atomic structure and high density of low-coordination sites, is regarded as the most competitive new catalyst for environmental catalysis. However, the efficiency and stability of metallic glass catalysts are often affected by their atomic configuration. Thus, the design and regulation of the nanoscale structure of metallic glasses to improve their catalytic efficiency and stability remains a challenge. Herein, a non-noble component, Fe75 P15 C10 amorphous ribbon, is used as a precursor to fabricate a hierarchical gradient catalyst with nanoscale heterogeneous and oxygenous amorphous structure by simple annealing and acid-immersing. The resulting catalyst offers an ultrahigh catalytic ability of kSA• C0 = 3101mgm-2 min-1 and excellent reusability of 39 times without efficiency decay in dye wastewater degradation. Theoretical calculations indicate that the excellent catalytic performance of the catalyst can be attributed to its unique heterogeneous nanoglass structure, which induces oxygen atoms. Compared to the FePC structure, the FeP/FePCO structure exhibits strong charge transferability, and the energy barrier of the rate-determining steps of the conversion of S2 O8 2- to SO4 -• is reduced from 2.52 to 0.97eV. This study reveals that a heterogeneous nanoglass structure is a new strategy for obtaining high catalytic performance.

Terrace-Rich Ultrathin PtCu Surface on Earth-Abundant Metal for Oxygen Reduction Reaction.

The activity and stability of the platinum electrode toward the oxygen reduction reaction are size-dependent. Although small nanoparticles have high Pt utilization, the undercoordinated Pt sites on their surface are assumed to have too strong oxygen binding strength, thus often leading to compromised activity and surface instability. Herein, we report an extended nanostructured PtCu ultrathin surface to reduce the number of low-coordination sites without sacrificing the electrochemical active surface area (ECSA). The surface shows (111)-oriented characteristics, as proven by electrochemical probe reactions and spectroscopies. The PtCu surface brings over an order of magnitude increase in specific activity relative to commercial Pt/C and nearly 4-fold enhancement in ECSA compared to traditional thin films. Moreover, due to the weak absorption of air impurities (e.g., SO2, NO, CO) on highly coordinated sites, the catalyst displays enhanced contaminant tolerance compared with nanoparticulate Pt/C. This work promises a broad screening of extended nanostructured surface catalysts for electrochemical conversions.

A Review of Theoretical Studies on Carbon Monoxide Hydrogenation via Fischer-Tropsch Synthesis over Transition Metals.

The increasing demand for clean fuels and sustainable products has attracted much interest in the development of active and selective catalysts for CO conversion to desirable products. This review maps the theoretical progress of the different facets of most commercial catalysts, including Co, Fe, Ni, Rh, and Ru. All relevant elementary steps involving CO dissociation and hydrogenation and their dependence on surface structure, surface coverage, temperature, and pressure are considered. The dominant Fischer-Tropsch synthesis mechanism is also explored, including the sensitivity to the structure of H-assisted CO dissociation and direct CO dissociation. Low-coordinated step sites are shown to enhance catalytic activity and suppress methane formation. The hydrogen adsorption and CO dissociation mechanisms are highly dependent on the surface coverage, in which hydrogen adsorption increases, and the CO insertion mechanism becomes more favorable at high coverages. It is revealed that the chain-growth probability and product selectivity are affected by the type of catalyst and its structure as well as the applied temperature and pressure.

The enhanced peroxymonosulfate activation ability and mechanism on low-coordinated Fe-N3 single sites for organic pollutant degradation in wastewater

For boosting the intrinsic peroxymonosulfate (PMS) catalytic activity of single atom catalysts (SACs), we fabricate zeolitic imidazolate framework (ZIF)-derived Fe SAC with different nitrogen coordination numbers (denoted as Fe-Nx/C) to boost organic pollutant oxidation. X-ray absorption fine structure (XAFS) spectroscopy was undertaken to determine the coordination configuration of Fe–N path. As expected, the resultant Fe-N3/C exhibited more excellent PMS catalysis activity with a p-nitrophenol (4-NP) degradation kinetic rate constant (kobs) of 0.061 min−1 that is 2.4-fold enhancement relative to the Fe-N4/C. Electron paramagnetic resonance (EPR) measurements and quenching tests confirmed the 1O play the main role associated with high-valent Fe–oxo and a small amount of OH and SO4− species. Density functional calculations revealed that low coordinated Fe–N3 sites prefer to form a bridge coordination bond structure of O-Fe-O with the adsorption sites of O2 and O1 in PMS molecule, exhibiting stronger interaction with the oxidant and better electron donating capability to enhance PMS activation comparing to common Fe-N4 structure based on charge deformation density, electron localization function (ELF) and projected density of state (PDOS) analysis. These findings indicate that microstructure modulation is a useful avenue to prepare a high-performance Fenton-like SACs.

Au/Pt Bimetallic Nanowires with Stepped Pt Sites for Enhanced C-C Cleavage in C2+ Alcohol Electro-oxidation Reactions.

Efficient C-C bond cleavage and oxidation of alcohols to CO2 is the key to developing highly efficient alcohol fuel cells for renewable energy applications. In this work, we report the synthesis of core/shell Au/Pt nanowires (NWs) with stepped Pt clusters deposited along the ultrathin (2.3 nm) stepped Au NWs as an active catalyst to effectively oxidize alcohols to CO2. The catalytic oxidation reaction is dependent on the Au/Pt ratios, and the Au1.0/Pt0.2 NWs have the largest percentage (∼75%) of stepped Au/Pt sites and show the highest activity for ethanol electro-oxidation, reaching an unprecedented 196.9 A/mgPt (32.5 A/mgPt+Au). This NW catalyst is also active in catalyzing the oxidation of other primary alcohols, such as methanol, n-propanol, and ethylene glycol. In situ X-ray absorption spectroscopy and infrared spectroscopy are used to characterize the catalyst structure and to identify key reaction intermediates, providing concrete evidence that the synergy between the low-coordinated Pt sites and the stepped Au NWs is essential to catalyze the alcohol oxidation reaction, which is further supported by DFT calculations that the C-C bond cleavage is indeed enhanced on the undercoordinated Pt-Au surface. Our study provides important evidence that a core/shell structure with stepped core/shell sites is essential to enhance electrochemical oxidation of alcohols and will also be central to understanding electro-oxidation reactions and to the future development of highly efficient direct alcohol fuel cells for renewable energy applications.

Atomic coordination environment engineering of bimetallic alloy nanostructures for efficient ammonia electrosynthesis from nitrate

Electrochemical nitrate reduction reaction (NO3RR) to ammonia has been regarded as a promising strategy to balance the global nitrogen cycle. However, it still suffers from poor Faradaic efficiency (FE) and limited yield rate for ammonia production on heterogeneous electrocatalysts, especially in neutral solutions. Herein, we report one-pot synthesis of ultrathin nanosheet-assembled RuFe nanoflowers with low-coordinated Ru sites to enhance NO3RR performances in neutral electrolyte. Significantly, RuFe nanoflowers exhibit outstanding ammonia FE of 92.9% and yield rate of 38.68 mg h-1 mgcat-1 (64.47 mg h-1 mgRu-1) at -0.30 and -0.65 V (vs. reversible hydrogen electrode), respectively. Experimental studies and theoretical calculations reveal that RuFe nanoflowers with low-coordinated Ru sites are highly electroactive with an increased d-band center to guarantee efficient electron transfer, leading to low energy barriers of nitrate reduction. The demonstration of rechargeable zinc-nitrate batteries with large-specific capacity using RuFe nanoflowers indicates their great potential in next-generation electrochemical energy systems.

Atomic Scale Observation of the Structural Dynamics of Supported Gold Nanocatalysts under 1,3‐Butadiene byin situEnvironmental Transmission Electron Microscopy

AbstractSupported gold catalysts have been reported to exhibit exceptional selectivity towards the desirable product, an alkene, in chemoselective hydrogenation of highly unsaturated alkynes and alkadienes. However, insights on the interactions between the gold nanoparticles and the 1,3‐butadiene adsorbates are lacking. In this work, using atomic scalein situETEM with the support of DFT‐based calculations, the reactivity of TiO2supported gold nanoparticles below 7 nm towards 1,3‐butadiene is investigated by monitoring their structure and dynamics under 105 Pa of 0.46 % C4H6/He during cooling at 300 °C and 200 °C. For sizes larger than 5 nm, the initial truncated octahedron morphology of gold nanoparticles is found to evolve towards a rounded morphology, with the growth of more open (110) surfaces and higher index facets at the expense of the initially present (100) and (111) facets, reflecting the adsorption of butadiene on low coordination sites at 300 °C. The morphology changes are shown to be accompanied by nucleation and glide of dislocations. At 200 °C, 1,3‐butadiene adsorption is shown to predominateon (111) facets, with the nanoparticles reverting to a faceted morphology while maintaining their fcc structure. For smaller particle size, Au fcc structure is also maintained under 1,3‐butadiene.

Designed Nanomaterials for Electrocatalytic Organic Hydrogenation Using Water as the Hydrogen Source.

ConspectusThe hydrogenation reaction is one of the most frequently used transformations in organic synthesis. Electrocatalytic hydrogenation by using water (H2O) as the hydrogen source offers an efficient and sustainable approach to synthesize hydrogenated products under ambient conditions. Such a technique can avoid the use of high-pressure and flammable hydrogen gas or other toxic/expensive hydrogen donors, which usually cause environmental, safety, and cost concerns. Interestingly, utilizing easily available heavy water (D2O) for deuterated syntheses is also attractive due to the widespread applications of deuterated molecules in organic synthesis and the pharmaceutical industry. Despite impressive achievements, electrode selection mainly relies on trial-and-error modes, and how electrodes dictate reaction outcomes remains elusive. Therefore, the rational design of nanostructured electrodes for driving the electrocatalytic hydrogenation of a series of organics via H2O electrolysis is developed.In this Account, we review recent advances in the electrocatalytic hydrogenation of different types of organic functional groups, including C≡C, C≡N, C═C, C═O, and C-Br/I bonds, -NO2, and N-heterocycles, with H2O over nanostructured cathodes. First, the general reaction steps (reactant/intermediate adsorption, active atomic hydrogen (H*) formation, surface hydrogenation reaction, product desorption) are analyzed, and key factors are proposed to optimize hydrogenation performance (e.g., selectivity, activity, Faradaic efficiency (FE), reaction rate, and productivity) and inhibit side reactions. Then, ex situ and in situ spectroscopic tools to study key intermediates and interpret mechanisms are introduced. Third, based on the knowledge of key reaction steps and mechanisms, we introduce catalyst design principles in detail on how to optimize the adoption of reactants and key intermediates, promote the formation of H* from water electrolysis, inhibit hydrogen evolution and side reactions, and improve the selectivity, reaction rate, FEs, and space-time productivity of products. We then introduce some typical examples. (i) P- and S-modified Pd can decrease C═C adsorption and promote H* formation, enabling semihydrogenation of alkynes with high selectivity and FEs at lower potentials. Then, creating high-curvature nanotips to concentrate the substrates further speeds up the hydrogenation process. (ii) By introducing low-coordination sites into Fe and combining low-coordination sites and surface fluorine to modify Co to optimize the adsorption of intermediates and facilitate H* formation, hydrogenation of nitriles and N-heterocycles with high activity and selectivity is obtained. (iii) By forming isolated Pd sites to induce a specific σ-alkynyl adsorption of alkynes and steering S vacancies of Co3S4-x to preferentially adsorb -NO2, hydrogenation of easily reduced group-decorated alkynes and nitroarenes with high chemoselectivity is realized. (iv) For gas reactant participated reactions, by designing hydrophobic gas diffusion layer-supported ultrasmall Cu nanoparticles to enhance mass transfer, improve H2O activation, inhibit H2 formation, and decrease ethylene adsorption, ampere-level ethylene production with a 97.7% FE is accomplished. Finally, we provide an outlook on the current challenges and promising opportunities in this area. We believe that the electrode selection principles summarized here provide a paradigm for designing highly active and selective nanomaterials to achieve electrocatalytic hydrogenation and other organic transformations with fascinating performances.

Metal particle size effects over the Ni/SAPO-11 bifunctional catalyst

The prominent size effects of metal nanoparticles (NPs) are mainly reflected in the change of electronic and geometric properties, which may induce distinct catalytic performance of the catalyst. Herein, Ni/SAPO-11 bifunctional catalysts with controllable sizes of Ni NPs were synthesized to investigate the particle size effects in n-hexane hydroisomerization. The results show that decreasing Ni particle size from 11.7 to 5.3 nm increases the concentration of surface Ni atoms and the proportion of low-coordinated Ni sites (corner, step sites) by 1.7 and 1.5 times, respectively. The low-coordinated surface Ni atoms have rich dangling bonds and high surface energy, resulting in greatly improved H2 adsorption and activation abilities. Moreover, an increased proportion of low-coordinated Ni sites within the Ni cluster shifts the d-band center upward, further enhancing the adsorption and activation of reactants. The intrinsic catalytic activity (turnover frequency) of 5.3 nm Ni NPs is ca. 2 times as much as that of the 11.7 nm ones. Besides, the smaller Ni NPs enhanced the metal–acid synergy, leading to a higher selectivity to isomers. This work provides deep insights into the metal particle size effects over the bifunctional Ni/SAPO-11 hydroisomerization catalysts and can be extended to various metal supported catalysts.

Understanding the restructuring and degradation of oxide-derived copper during electrochemical CO2 reduction

Renewable energy produced through electrochemical CO2 reduction is promising for mitigating the energy crisis and environmental issues. Notably, oxide-derived copper (OD-Cu) has attracted considerable attention owing to its unique ability to catalyze CO2 electroreduction to >2e− products, especially C2+ products, which are the key feedstocks for the chemical process. However, Cu under operating conditions usually leads to structure reconstruction and degradation, which hinders understanding the origin of its activity. Understanding the restructuring and degradation of OD-Cu catalyst to form C2+ products is critical for understanding the active sites and, thus for designing effective and durable catalysts for CO2 reduction. This paper describes that Cu defect sites are easily dissolved during electrochemical CO2 reduction, and the presence of defect sites is strongly related to the catalytic performance of C2+ products. Here, the C2+ products Faradaic efficiency (FE) of OD-Cu decreased from 39.4% at 1 h to 26.0% at 5 h at −1.5 V vs. RHE, along with a decrease in low-coordinated defect sites. The low-coordinated defect sites facilitate CO adsorption and help to increase the CO coverage, thus promoting CO–CO coupling. The decrease in the number of defect sites and activity degradation is circumvented by promoting the Cu redeposition process. The C2+ products FE of OD-Cu can be maintained at ca. 47.2% without an obvious decrease in CO2-saturated 0.1 M KHCO3 with 1 mM Cu2+. The results of this study help in understanding the activity of OD-Cu and reveal its deactivation mechanism. This knowledge will aid in designing highly active and stable catalysts for CO2 reduction.

Noble-metal-free Co-N-C catalyst derived from cellulose-based poly(ionic liquid)s for highly efficient oxygen reduction reaction

Noble-Metal-Free nitrogen-doped carbon-based materials are promising electrocatalysts for oxygen reduction reaction (ORR), yet it remains a great challenge to construct efficient porous non-noble metal nitrogen-doped carbon (M-N-C) catalysts with uniform distribution, due to the easy aggregation of metals. Herein, we reported the synthesis and assessment of a novel and efficient noble-metal-free catalyst for oxygen reduction reaction (ORR) from pyrolysis of a cobalt-containing cellulosic poly(ionic liquid) (Co-N-C). The prepared Co-N-C catalyst possesses high surface area, hierarchical porous structure, well-dispersed Co nanoparticles and large amounts of low-coordinated Co active sites. Especially, the Co-N-C-850 sample exhibits a high ORR activity (Eonset = 0.827 V, E1/2 = 0.74 V) that can rival 20 wt% commercial Pt/C (Eonset = 0.833 V, E1/2 = 0.71 V) in alkaline media. Moreover, the Co-N-C-850 sample also shows excellent anti-methanol poisoning activity and long-term stability toward ORR compared with commercial Pt/C. Our study provides a promising avenue both for the development of non-noble M-N-C catalysts for fuel cells and the functional utilization of cellulose.