Lower Bond Strength Research Articles

Prolonged post-washing in ethanol decreases bond strength of additively manufactured crown materials

ObjectivesThis study aimed to investigate the effect of post-washing duration and crown thickness on the bond strength between additively manufactured crown materials and dental cement in vitro. MethodsRectangular-shaped specimens of two thicknesses (1.5 and 2.0 mm) were additively manufactured from permanent VarseoSmile Crown (VC) and long-term temporary NextDent (ND) materials. The specimens were post-washed (n = 160) in ethanol for 5 min, 10 min, 1 h, and 8 h then cemented with dual-cure resin cement. Twenty PMMA (TC) were milled as a control. A chevron-notch test was performed to measure the maximum load until failure (N). Interfacial bond strength (J/m2) was calculated and statistically analysed. The mode of failure was analysed by scanning electron microscopy (SEM). ResultsThere was a significant difference in the bond strength between all groups (p < 0.01). VC at 1.5mm thickness post-washed for 10 min showed the highest mean bond strength (1.77 ±0.96 J/m2) while VC at 2.0mm thickness post-washed for 8 h showed the lowest (0.22 ±0.10 J/m2). Exposure to ethanol for 8 h resulted in lower bond strength. Within the type of material, there were no differences in bond strength between the thicknesses when post-washed for the same duration. ConclusionsProlonged post-washing of AM crown materials can significantly decrease the bond strength to resin cement. There were no differences between the permanent and long-term temporary AM materials. When post-washed for 5 min, AM materials observed comparable or higher bond strength values compared to PMMA. Clinical significanceThe output of this research serves as a guide for dental practitioners, emphasising the importance of adhering to correct post-washing procedures for optimal bond strength of additively manufactured crown materials.

Bonding performance and interfacial adaptation of modern bulk-fill restorative composites after aging in artificial saliva: an in vitro study.

This study aimed at comparing the microtensile bond strength (MTBS) and interfacial adaptation of a modern self-curing and a light-curing restorative bulk-fill composite to a conventional composite applied with the layering technique. Forty-eight occlusal cavities were divided in three main groups (16/group) based on tested materials: (i) STELA, bulk-fill self-curing restorative (STELA, SDI Ltd.); (ii) 3M-BULK, bulk-fill composite (Filtek One Bulk-Fill, 3M Oral Care); and (iii) 3M-CTR, a conventional composite (Filtek Supreme XTE, 3M Oral Care). These were used in combination with their adhesives in self-etch (SE) or etch-and-rinse (ER) mode. Specimens stored in artificial saliva (24h or 12months) were evaluated for MTBS and fractography. The interfacial analysis was performed through confocal microscopy. ANOVA and Fisher's LSD post hoc tests were performed with a level of significance of 5%. All the tested materials applied in ER mode presented (24h) greater bond strength than in SE mode. Although all materials showed a significant drop in the bond strength after prolonged storage, STELA showed the highest bonding performance and interfaces with few gaps. 3M-BULK had the lowest bond strength and an interface with several voids and gaps. All materials were affected by interface degradation and bonding reduction over prolonged aging. However, their use in combination with adhesives applied in ER mode may offer greater immediate bonding performance. The use of restorative light-curing bulk-fill composites may generate gaps at the bonding interface and voids. STELA may represent a suitable alternative to avoid such issues.

Comparative Evaluation of Bond Strengths Between Dual Cure Resin Cement and Light Cure Resin Cement in Root Surface Indirect Restorations: An In Vitro Analysis Study.

Aim The aim of this study was to evaluate the shear bond strength betweendual cure and light cure resin cements in root surface indirect restorations. Materials and methods Ten recently extracted human teeth were selected. Cylindrical blocks of resin were prepared and bonded nearthe Cemento-Enamel Junction (CEJ) of the prepared teeth to mimic the restoration at the root surface.The samples were randomly luted to the root surface using the light cure (Calibra Veneer, Dentsply Sirona, India) and dual cure (Fusion Ultra D/C, DenPro, USA) formingtwo groups. The bond strength was checked using the INSTRON 3000 device (INSTRON, MA, USA). The point of fracture of the prepared sample from the tooth surface was noted. All readings were tabulated and further statistically analyzed. Results On comparing the two groups, it was found that the light cured resin had a greater mean shear bond strength (57 N) than the dual cure resin cement (41 N).The difference in the mean value of the shear bond strength between two resin cements was found to be statistically not significant according to independent T-test analysis using Levene's Test (P>0.05). Conclusion From the results obtained and within the limits of the study conducted, we can infer that Calibra Veneer is a more viable option for luting to the root surface area. On the other hand, Fusion Ultra Dual cure resin cement seems to have similar results but has a lower bond strength than the other.

Evaluation of Bond Strength and Adhesive Remnant Index of Different Lingual Retainers in Human Incisor Teeth

ABSTRACT Objective: This study aimed to evaluate and compare the bond strengths of four different lingual retainers and assess the adhesive remnant index (ARI) to determine their effectiveness in orthodontic retention. Methodology: Eighty human incisor teeth were divided into four groups, with each group bonded using a different retainer: Group 1 (E-Glass retainer), Group 2 (0.017” Co-axial stainless steel wire), Group 3 (Splint C.T. fiber mesh), and Group 4 (0.010” stainless steel ligature wire). Bond strength was measured using a universal testing machine, and ARI scores were recorded to assess bond failure types. Results: Group 1 (E-Glass retainer) demonstrated the highest bond strength, followed by Group 3 (Splint C.T. fiber mesh), Group 2 (Co-axial stainless steel wire), and Group 4 (stainless steel ligature wire). Cohesive bond failures were observed in most groups, except for the co-axial stainless steel wire group, which exhibited adhesive failures. Conclusion: E-Glass fiber-reinforced retainers showed the highest bond strength, making them a promising alternative to conventional stainless steel wires for orthodontic retention, especially in patients with esthetic concerns or nickel hypersensitivity. Stainless steel retainer groups exhibited lower bond strengths, and cohesive bond failures were prevalent. Further research is needed to validate these findings in clinical settings and evaluate the long-term effectiveness of different lingual retainers.

Dentin adhesion of bulk-fill composites and universal adhesives in class I-cavities with high C-factor

ObjectivesThe aim of this study was to compare the dentin adhesion of bulk-fill composites in high C-factor class I-cavities before and after thermocycling to a control group using incremental layering technique. MethodsA standardized class I-cavity was prepared into 195 human molars, then different universal adhesives were applied either in self-etch or etch & rinse mode, and the cavity was filled according to each materials application protocol. The material combinations used were a conventional layered composite as control, the respective bulk-fill product, two other bulk-fill composites made by different manufacturers, with one of them being tested using two different polymerization times. Furthermore, one thermoviscous bulk-fill composite and one self-adhesive restorative were examined of which the latter can only be applied in self-etch mode. In each group the dentin adhesion to the cavity bottom was measured using microtensile bond strength test initially (24 h water storage) and after thermocycling. All results were statistically analyzed using STATA 17.0. ResultsThe statistical analysis showed significant differences between the control and the experimental groups (p < 0.001). The highest mean bond strength before (14.8 ± 10.7 MPa) and after aging (14.2 ± 11.5 MPa) was measured for the etch & rinse-control group. Among the bulk-fill groups, the etch & rinse technique consistently showed higher bond strengths. Bond strength of groups with shortened polymerization did not exceed 2.1 MPa. The bond strength of the self-adhesive restoration material was low before and after thermocycling (2.7 MPa/ 0.0 MPa). Groups with low bond strength values showed a high number of pre-testing-failures. ConclusionsBulk-fill materials used in high C-factor class I-cavities showed lower bond strength during self-etch application. The same applies for a shortened polymerization regime, which cannot be recommended for high C-factor cavities. Clinical significanceToday, a large variety of materials and application techniques can be used when placing an adhesive restoration. Whether new instead of established procedures should be applied in high C-factor cavities has to be critically assessed, as they are a demanding scenario for adhesive restorations.

Effect of Protein Surface Hydrophobicity and Surface Amines on Soy Adhesive Strength.

Soy is considered one of the most promising natural materials for manufacturing wood adhesives due to its low cost, high protein content, and ready availability. However, more cost-effective ways of improving its wet shear strength are needed to achieve wider market acceptance. Protein adhesive wet strength depends on the use of (typically expensive) crosslinking additives as well as the processing/denaturation of the protein. It has been commonly stated in the literature that protein denaturation leads to higher bond strength by activating the surface and exposing the reactive groups. Therefore, we investigated how differences in surface reactive groups (surface hydrophobicity and reactive amine groups) brought on with different denaturation treatments relate to bonding performance. Fourteen soy protein isolates (SPIs) with different denaturation histories were investigated. Characterization of the SPIs included surface hydrophobicity, surface amine content, extent of protein hydrolysis, and bond strength (wet and dry, with and without polyamidoamine epichlorohydrin (PAE) crosslinking agent) by ASTM D7998. The molecular weight patterns showed that proteins denatured by extensive hydrolysis had very low bond strengths. Adding the crosslinker, PAE, improved all the shear strength values. We found that the number of water-accessible reactive amine groups on protein surfaces had no impact on the adhesive strength, even with the amine-reactive crosslinker, PAE. Conversely, increased surface hydrophobicity was beneficial to adhesive strength in all cases, though this correlation was only statistically significant for wet strength without PAE. While, in general, denatured proteins are typically thought to form better bonds than native state proteins, this work suggests that it matters how proteins are denatured, and what surfaces become exposed. Denaturation by hydrolysis did not improve bond strength, and extensive hydrolysis seemed highly detrimental. Moreover, exposing hydrophobic surface groups was beneficial, but exposing covalent bond-forming reactive amine groups was not.

Influence of Diabetes Mellitus and Universal Adhesive Application Mode on the Bond Strength of Composite Resin to Dentine.

The aim of the current study was to evaluate the influence of diabetes mellitus and the mode of applying a universal adhesive on the shear bond strength of composite resin to dentin. Forty teeth were extracted from diabetic individuals who had been living with diabetes for a period of 5 to 15 years. These forty teeth were divided into two groups: twenty molars from patients with type 1 diabetes and twenty molars from patients with type 2 diabetes. The remaining twenty sound human molars were collected from non-diabetic patients. The collected teeth were assigned into 3 groups, and each group was further divided into 2 subgroups. Group A (n = 20): non-diabetic (ND) where sub group IA: Universal adhesive applied in the total-etch mode (n = 10) and sub group IIA: Universal adhesive applied in the self-etch mode (n = 10). Group B (n = 20): diabetic type 1 (D1) where sub group IB: Universal adhesive applied in the total-etch mode (n = 10) and sub group IIB: Universal adhesive applied in the self-etch mode (n = 10). Group C (n = 20): diabetic type 2 (D2). Where Sub group IC: Universal adhesive applied in the total-etch mode (n = 10) and sub group IIC: Universal adhesive applied in the self-etch mode (n = 10). A Teflon mold measuring 3mm in diameter was attached to the dentin surface, used to build Filtek Z550 to a height of 3mm. The specimens were fixed to the universal testing to measure shear bond strength. There was a statistically significant difference of Mean ±SD of shear bond strength among the three tested groups. In group A, the Mean ±SD were (21.710 ± 0.638), it was decreased in group B to (14.626 ± 0.726) and group C to (17.740 ± 0.668). Subgroup I had lower shear bond strength values than subgroup II in all tested groups. The difference between each subgroup in groups A, B, and C was significant. 1. Diabetes mellitus has an adverse effect on the shear bond strength of composite to dentine. 2. Type 1 diabetes mellitus significantly reduces the shear bond strength of composite resin to dentin. 3. Shear bond strength of the universal adhesive was higher when applied to dentin using the self-etch mode, as compared to the total etch mode, in all groups, regardless of whether the participants had diabetes or not. Key words:Diabetes Mellitus, Universal Adhesive, Application Mode, Shear bond Strength, Dentine, Composite.

Effect of bioceramic intracanal medication on the dentinal bond strength of bioceramic cements: an ex-vivo study.

The present study evaluated the effect of a bioceramic intracanal medicament (Bio-C Temp) on the push-out bond strength of bioceramic cements. Forty-eight human single-canaled premolars were prepared and randomly divided into three groups: Group (A) received no intracanal medicament; Group (B) calcium hydroxide (CH); and Group (C) Bio-C Temp. After medicament removal, the roots were sectioned transversely. The slices in each group were separated into two subgroups (n = 16): in Subgroup (1), mineral trioxide aggregate (MTA) was placed, and in Subgroup (2) Bio-C Repair. Push-out bond strength was determined using a universal testing machine, applying a constant compressive force on the cement until bond failure. The failure mode was also evaluated. Data were analyzed using the Chi-square test and two-way ANOVA followed by Tukey's post hoc tests. The level of significance was set at 5%. The pushout bond strength of Bio-C Repair was significantly higher than that of MTA irrespective of intracanal medication (p = 0.005). The placement of Bio-C Temp was associated with significantly lower bond strength (p = 0.002, p = 0.001). Bio-C Repair showed better bond strength compared to MTA, irrespective of intracanal medication. Bio-C Temp intracanal medicament, however, decreased the bond strength of both these cements.

Influence of stress-relieving heat treatments on the efficacy of Co-Cr-Mo-W alloy copings fabricated using selective laser melting.

Purpose This study aimed to evaluate the influence of stress-relieving heat treatments on the metal-ceramic bond strength and fitness accuracy of selective laser melting (SLM)-fabricated Co-Cr alloy copings.Methods SLM-manufactured Co-Cr samples were stress-relieved at 750 (Ht-750) and 1150 °C (Ht-1150). The microstructure, surface roughness, metal-ceramic bond strength, marginal and internal fit, Vickers hardness, and residual stress were then compared with those of the non-heat-treated group (As-built). The results were analyzed using one-way ANOVA and post-hoc tests (Tukey's or Student's t test) (P = 0.05).Results The microstructure of the Ht-1150 samples had a brittle oxide layer and lower surface roughness, resulting in significantly lower bond strength values than those of the other groups. The As-built group exhibited significantly lower marginal gap values than the Ht-750 and Ht-1150 groups. Therefore, the post-heat treatments degraded the marginal fitness. The surface residual stress in all sample groups were compressive because of the sandblasting effect. The compressive stresses were larger in Ht-1150 than in As-built and Ht-750 owing to their low hardness values.Conclusions Stress-relief annealing porcelain-fused-to-metal single crowns does not improve bond strength and degrades fitness accuracy because additional post-heat treatments induce thermal distortion. These findings are expected to facilitate the direct application of As-built SLM single crowns in dentistry to minimize post-manufacturing costs and time.

Effects of blood and root-dentin cleaning on the porosity and bond strength of a collagen bioceramic material.

To assess the effect of cleaning protocols on dentin contaminated with blood in reparative endodontic materials, bovine root samples were divided: no contamination (N); contamination (P); contamination and cleaning with saline (S), 2.5% NaOCl+saline (Na) or 2.5% NaOCl+17% EDTA+saline (NaE) and filled with: mineral trioxide aggregate (MTA), calcium-aluminate-cement (C), or C+collagen (Ccol) (n=13). The samples were evaluated for porosity, chemical composition, and bond strength. MTA porosity was lower than C (p=0.02) and higher than Ccol (p<0.001). P and NaE were similar (p=1.00), but higher than the other groups (p<0.001). MTA bond strength was similar to Ccol (p=0.777) and lower than C (p=0.028). P presented lower bond strength than the N (p<0.001); S and Na were similar to each other (p=0.969), but higher than P and lower than N (p<0.001). It was observed a predominance of mixed and cohesive failures. None of the samples showed Ca/P ratio values similar to human hydroxyapatite. This study showed that contamination with blood increased the materials porosity, but dentin cleaning with 2.5% NaOCl reduced this effect, and the collagen additive reduced the material porosity. Furthermore, blood contamination reduced the materials bond strength, and cleaning with saline or 2.5% NaOCl diminished this effect.

Fuerza de unión de resina compuesta/adhesivo universal a dentina sometida a radio-terapia

Aim: To evaluate the bond strength of a universal adhesive system to dentin submitted to radiotherapy. Materials and Methods: Sixty extracted human teeth were divided into two groups (n = 30): without radiotherapy (control); with radiotherapy, according to the adhesive protocol (n=15): ER-etch-and-rinse (acid + Single Bond Uni-versal); SE-self-etch (Single Bond Universal). The analyzes were shear bond strength (SBS) (n=10), failure pattern (n=10) and scanning electron microscopy (n=5). Data was analyzed by a two-way ANOVA (α =0.05). Results: The radiotherapy decreased SBS of the restorative material to dentin (p&lt;0.0001). The ER protocol provided lower bond strength values (p&lt;0.001). The predominant type of fracture without radiotherapy was mixed (SE), cohesive to the material (ER). Both protocols presented adhesive failures with radiotherapy. Teeth had a hybrid layer and long resin tags (without radiotherapy) and few tags (with radiotherapy). Conclusions: The SE adhesive mode favors the shear bond strength of resin to dentin in teeth submitted to radiotherapy. Keywords: Dental Cements; Adhesives; Dental bonding; Self-curing of dental Resins; radiation treatment; Dentin.

Bond Strength of Steel Bars in Sustainable Concrete Made with Recycled Aggregates

Lately, considerable efforts have been directed towards investigating the practicality of using coarse recycled concrete aggregate as a potential substitute for natural coarse aggregate (NCA) in concrete construction. Research has shown that both the proportion of replacement and the properties of recycled aggregates play a significant role in affecting the tensile strength, compressive strength, and bonding characteristics of concrete. In certain cases, recycled aggregate concrete exhibits lesser mechanical properties when compared to concrete made with normal aggregates. The current study investigated the performance of Sika AnchorFix-1 to enhance the bond strength between steel bars and recycled aggregate concrete. The findings suggest that Sika AnchorFix-1 successfully prevented the concrete rupture in the case of concrete with recycled concrete aggregates, whereas concrete rupture could not be prevented in the case of concrete with recycled brick aggregates. Hence, a lower bond strength was obtained for specimens with recycled bricks aggregates than specimens with recycled concrete aggregates.

The Effect of Titanium Anodization on the Bond Strength of 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) Resin Cement.

To examine the effects of anodization and different surface modifications of titanium on bond strength to 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) resin cement. Grade 5 titanium alloy disks (n = 160) were assigned to one of five prebonding surface treatment study groups (polished; polished and anodized; polished, etched, and anodized; sandblasted; sandblasted and anodized). Disks were adhesively bonded with 10-MDP resin cement (Panavia 21; bonding area: 3.3 mm in diameter) to composite resin cylinders. In each study group, tensile bond strength tests were conducted after 24 ± 1 hours and after 6 months (180 ± 2 days) of water storage (n = 16 specimens per water storage subgroup). Debonded specimens were stereomicroscopically analyzed to determine their fracture mode. Statistics included one-way and multifactorial ANOVA and Tukey post hoc tests (α = .05). Anodization and water storage did not significantly (P ≥ .389) affect tensile bond strength. Although subgroups of polished samples had significantly (P ≤ .031) lower bond strengths (subgroup mean values: 20 to 26 MPa) than etched or sandblasted samples (subgroup mean values: 29 to 33 MPa), they nonetheless exceeded the empirical threshold of 10 MPa used as a criterion for clinical recommendation. The fracture mode of all test specimens was predominantly cohesive. Anodization of titanium surfaces can be performed without weakening the adhesion of 10-MDP-based resin cement to titanium.

Effect of ethanolic extract of propolis on antibacterial and microshear bond strength of glass-ionomer restorations to dentin

ObjectivesThis study was conducted to evaluate the effect of ethanolic extract of propolis on antibacterial and microshear bond strength of glass ionomer restorations to dentin. Materials and methodsConventional glass ionomer cement (Equia forte, GC Tokyo, Japan), resin-modified glass ionomer (Fuji II LC, GC Tokyo, Japan) and propolis powder (dried extract from honey bees) materials were used in this study. Both conventional glass ionomer and resin-modified glass ionomer were modified by two different concentrations of ethanolic extract of propolis (10 % and 25 % EEP). For antibacterial test, Streptococcus mutans strain was spread on agar petri dishes using a sterile swab. Discs of both glass ionomer restorative materials (without adding EEP, with 10 % EEP and with 25 % EEP) were fabricated within the agar plates. Antibacterial activity was evaluated by measuring the inhibition zones around each disc. For microshear bond strength test, 60 healthy human permanent molars were prepared by cutting occlusal surface and expose the dentin at the height of contour of all teeth then conditioned using poly acrylic acid conditioner, both glass ionomer restorative materials (without adding EEP, with 10 % EEP and with 25 % EEP) were mixed and applied on conditioned dentin surface by using tygon tube. Microshear bond strength was evaluated by the universal testing machine. ResultsTwo-way ANOVA test revealed that both glass ionomer type and different concentrations of EEP had significant effect on the antibacterial test results and microshear bond strength values (p < 0,05). Glass ionomer restorative material with 25%EEP had the highest antibacterial values whereas glass ionomer restorative material without modifications (control groups) had the lowest values. Resin-modified glass ionomer without any modification (control group) had the highest bond strength while resin-modified glass ionomer with 25%EEP had the lowest bond strength. ConclusionsIncorporation of ethanolic extract of propolis to glass ionomer restorative material increases the antibacterial effects of both conventional GIC and RMGI. Inspite of this advantage, it seems that it has deleterious effect on microshear bond strength to dentin.

Mode I fracture analysis of Fe-SMA bonded double cantilever beam considering nonlinear behavior of the adherends

In the scope of developing a bonded iron-based shape memory alloy (Fe-SMA) strengthening solution, nonlinear deformation in the adherends upon joint failure due to phase transformation and high adhesive toughness is unavoidable. The effect of this nonlinear deformation has not been studied in the case of Mode I failure. In this study, the first experimental and theoretical investigation on Mode I failure of Fe-SMA bonded joints is presented. A new analytical model is proposed and validated using experimental results to gain an in-depth understanding of the influence of Fe-SMA nonlinear material deformation on the joint failure process. The proposed model is shown to be significantly faster than traditional elasto-plastic finite elements using cohesive zone modeling with a minimum compromise to the accuracy. These are observed to result in lower bond strength and a shorter fracture process zone than that of linear elastic adherends using the same adhesive. Neglecting the nonlinear behavior of the Fe-SMA bonded joints can lead to an unconservative joint design, jeopardizing safety. The developed model is aimed at facilitating the development of adhesively bonded Fe-SMA strengthening systems.

Engineering Mn–O strength in manganese oxide catalyst to enhance propane catalytic oxidation

Developing highly active and thermally stable transition-metal-oxide catalysts for light alkane catalytic oxidation is of great importance but very challenging. In the work, the catalytic performance for propane deep oxidation was significantly enhanced on the Mn1NixOy solid solution catalyst by weakening the Mn–O bond strength of manganese oxide. The characterization results combined with DFT calculations demonstrated that the introduction of Ni could create additional defect sites, resulting in a significant improvement of the adsorption and the activation of both propane and oxygen molecules. The optimal Mn1Ni0.15Oy catalyst exhibits abundant oxygen vacancies with low MnO bond strength, high redox ability and oxygen mobility, which account for its superior activity. Specifically, the specific reaction rate on Mn1Ni0.15Oy is three times higher than that on pure Mn2O3. Moreover, a Mn1Ni0.15Oy/cordierite monolithic catalyst was made by wash-coating method, and exhibited remarkable catalytic performance and stability on catalytic oxidation of propane during the 45 days (1080 h) on stream, even after tens of high temperature thermal shocks (up to 650 ℃), which declared to be satisfied for practical industrial applications. This work will shed light on designing high-efficiency and long-life environmental catalyst for VOCs elimination.

Bond Strength of Reinforcing Steel Bars in Self-Consolidating Concrete

This paper presents an experimental investigation of the bond strength of reinforcing steel bars in tension in self-consolidating concrete (SCC). The effects of the reinforcing bar’s location, orientation, size, and coating on the bond strength with SCC were studied and compared to those with conventionally vibrated concrete (CVC). Several SCC mixtures were developed to cover a wide range of applications/components and material types. The fresh properties of the SCC mixtures were determined to evaluate their filling ability, passing ability and stability. Two hundred and thirty-four pull-out tests of rebars embedded in cubes, wall panels and slabs were conducted. Almost half of the tests were conducted to evaluate the bond with SCC and the other half with CVC. Load–slippage relationships were measured for each test. Pull-out test results were analyzed, and the bond strength was reported in two values: critical strength, which corresponds to slippage of 0.01 in. *0.25 mm); and ultimate strength, which corresponds to the maximum load. The critical strength of SCC and CVC were compared against the ACI 318-19 provisions and comparisons between the ultimate strength of SCC and CVC were conducted. The comparisons indicated that SCC has lower bond strength with vertical rebars than CVC, and a 1.3 development length modification factor is recommended. A similar conclusion applies to epoxy-coated and large diameter rebars. Also, SCC with high slump flow has shown a less top-bar effect than that of CVC.

Evaluation of Shear Bond Strength and Microleakage of Self-adhesive Giomer

This study was aimed to evaluate the bonding performance of a self-adhesive giomer and compare it to a conventional flowable composite resin with regard to shear bond strength and microleakage in enamel and dentin. Healthy human premolars extracted for orthodontic treatments were used in the study. For shear bond strength tests, enamel and dentin specimens were prepared for the study group with selfadhesive giomer and for the control group with conventional flowable composite resin with a 5th-generation adhesive system. A universal testing machine was used to measure the shear bond strength. For the microleakage tests, specimens were immersed in a 2% methylene blue solution for 24 hours, cut into sections, and evaluated with a stereomicroscope for the extent of dye penetration. The results of the study showed no statistically significant difference in shear bond strength between the self-adhesive giomer and the conventional flowable composite resin in enamel (&lt;i&gt;p&lt;/i&gt; = 0.091). On the contrary, in dentin, the self-adhesive giomer showed significantly lower shear bond strength (&lt;i&gt;p&lt;/i&gt; &lt; 0.0001). The microleakage of the selfadhesive giomer was significantly higher than that of the conventional flowable composite resin (&lt;i&gt;p&lt;/i&gt; = 0.002). Self-adhesive giomer is considered useful for restoring small cavities at the enamel level of pediatric patients by reducing chair time with the advantage of a simple bonding process. However, as the study was conducted in a laboratory setting, further research in a clinical environment is deemed necessary.

Shear bond strength characteristics on surface treatment modalities of CAD-CAM resin polymers.

The purpose of this in vitro study was to analyze the shear bond strength of composite resin to a commercially available high-performance polymer material for fixed, screw-retained full arch restorations. A total of 135 computer-aided design and computer-aided manufacturing, high-performance polymer (HPP) blocks were cut and obtained from discs (Trilor 95, Harvest Dental, Brea, CA). The samples were 10mm × 10mm × 10mm. The specimen surfaces were grouped as untreated (Group A), 50 μm Al2O3 (Group B), 110 μm Al2O3 (Group C), Rocatec (3M, St. Paul, MN) activated with silica-modified alumina oxide treatment (Group D); and trimmed coarsely with a carbide bur (Group E). Group A samples were used as controls. After surface treatments, the specimens were gently cleansed with oil-free steam and alcohol wipes. Surface conditioning was performed on all physically treated samples. The manufacturer's recommendations were followed for bonding composite resin to the samples with light-cured Visio.link (Bredent, Chesterfield, UK). Cylinders were veneered with composite resins (diameter 5mm, height 4mm) and polymerized on the specimen surfaces through plastic tubes. Twenty-seven specimens were used for each testing group and aging tests were performed. The experimental samples were thermocycled. Shear bond strength and scanning electron microscopic tests were performed. Means and standard deviations were calculated. Statistical analysis was performed with post-hoc Tukey tests. Statistical analysis revealed that there was a significant difference between the groups (p<0.001). The highest shear bond strengths were achieved for the specimens bonded with Visio.link without physical surface treatments (270.47MPa). The lowest bond strengths were found for specimen surfaces abraded with 110 μm Al2O3 (117.03 Mpa) CONCLUSIONS: The results of this laboratory study indicated that the specimens used with Visio.link as provided by the manufacturer had the highest shear bond strengths between the composite resin and high-performance polymer test specimens. Modifications of the high-performance polymer surfaces with carbide burs did not change bonding strengths with the composite materials.

Measuring the Shear Bound Strength on Acrylic Resin Veneer to Metal Surface of Nickel (A Comparative Study)

The bound strength of metal resin interface of prosthesis is a key factor in determining the service ability of that prosthesis. The main objective of this study was to determine the effect of different surface treatment on the shear bond strength of Ni-Cr alloy (CB-Blando 72 alloy) and heat cured acrylic veneer resin (Vertex). Thirty disc shaped samples from base plate wax were prepared, the diameter of disc was (8 mm x 4.5 mm). After casting the metal, the samples were cleaned, finished and polished by silicon carbide abrasive paper with grit size (600 μm) and then the profilometer was u sed to determine the surface roughness of samples. Then the sa mples were divided in to three groups, each group contain (10) sa mples. The first group rece ived no treatment and serve as control .The Second group received micro mechanical treatment using 250 μm Al2o3 .The third group recived micro mechanical treatment using 400 μm Al2o3. The acrylic was prepared as a round shape (8 μm) in diameter and (2 μm) in thickness, which was placed on the metal surface treatment, the acrylic was fabricated in the same conventional way for construction veneer resin. Then all samples was tested the shear bond strength by using Instron universal testing machine .The result from this study showed that, the first group was give low shear bond strength while the second group showed that the air abrasion with 250 μm Al2o3 give the highest shear bond values when compared with the third group which air abrasive with 400 μm Al2o3.