High Strength Low Alloy Steel Research Articles

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Numerical Simulation of Fatigue Crack Growth and Fracture in Welded Joints Using XFEM—A Review of Case Studies

Numerical simulation of fatigue crack growth in welded joints is not well represented in the literature, especially from the point of view of material heterogeneity in a welded joint. Thus, several case studies are presented here, including some focusing on fracture, presented by two case studies of mismatched high-strength low-alloyed (HSLA) steel welded joints, with cracks in the heat affected zone (HAZ) or in weld metal (WM). For fatigue crack growth, the extended finite element method FEM (XFEM) was used, built in ABAQUS and ANSYS R19.2, as presented by four case studies, two of them without modelling different properties of the welded joint (WJ). In the first one, fatigue crack growth (FCG) in integral (welded) wing spar was simulated by XFEM to show that its path is partly along welded joints and provides a significantly longer fatigue life than riveted spars of the same geometry. In the second one, an integral skin-stringer panel, produced by means of laser beam welding (LBW), was analysed by XFEM in its usual form with stringers and additional welded clips. It was shown that the effect of the welded joint is not significant. In the remaining two papers, different zones in welded joints (base metal—BM, WM, and HAZ) were represented by different coefficients of the Paris law to simulate different resistances to FCG in the two cases; one welded joint was made of high-strength low-alloyed steel (P460NL1) and the other one of armour steel (Protac 500). Since neither ABAQUS nor ANSYS provide an option for defining different fatigue properties in different zones of the WJ, an innovative procedure was introduced and applied to simulate fatigue crack growth through different zones of the WJ and evaluate fatigue life more precisely than if the WJ is treated as a homogeneous material.

Effect of Heat Treatment on Impact Transition Temperature of High Strength Low Alloy Steel (HSLA) Steel Rods

Effect of Heat Treatment on Impact Transition Temperature of High Strength Low Alloy Steel (HSLA) Steel Rods

Exploring Through-Thickness Residual Stress Distribution in Double V-Groove Multipass Welds of High-Strength Low-Alloy Steel and the Impact of Mechanical Restraints

Exploring Through-Thickness Residual Stress Distribution in Double V-Groove Multipass Welds of High-Strength Low-Alloy Steel and the Impact of Mechanical Restraints

Dynamic Deep Learning to Predict Mechanical Properties of High-Strength Low-Alloy Steels

Dynamic Deep Learning to Predict Mechanical Properties of High-Strength Low-Alloy Steels

Effect of Interlayer Temperature on Microstructure and Properties of High-Strength Low-Alloy Steel Manufactured Using Submerged-Arc Additive Manufacturing (SAAM).

Controlled interlayer temperature has a profound impact on both the microstructure and mechanical properties of the deposited components. In this study, thin-walled structures made of high-strength low-alloy steel were fabricated using the submerged-arc additive manufacturing process. The effects of varying temperature on the microstructure and mechanical properties of the components were studied. The results showed that the cooling rate within T8/5 decreased as the interlayer temperature increased, which caused the microstructure to transition from a fine-grained structure dominated by bainitic ferrite and granular bainite to a coarse-grained structure dominated by polygonal ferrite. The measurement of mechanical properties showed that due to the influence of the fine-grained structure, the components with low interlayer temperatures exhibit excellent hardness, high strength, and outstanding ductility and toughness. Furthermore, a faster cooling rate disrupts the stability of carbon diffusion, resulting in the development of increased quantities of residual austenitic films within the components with controlled low interlayer temperatures. This augmentation in residual austenite films strengthens the components' ductility and toughness, enabling the deposited components to exhibit exceptional impact toughness in low-temperature environments.

Assessment of vanadium influence on the microstructure and mechanical behavior high-strength low-alloy steel welded joints

Assessment of vanadium influence on the microstructure and mechanical behavior high-strength low-alloy steel welded joints

Experimental and Numerical Characterization of Local Properties in Laser-Welded Joints in Thin Plates of High-Strength–Low-Alloy Steel and Their Dependence on the Welding Parameters

Laser welding on thin plates of high-strength steel is increasing in various industrial applications. The mechanical behavior of welded joints depends on their local properties, which in turn depend on the welding parameters applied to join the base material. This work characterizes the local properties of butt-welded joints of thin plates of high-strength–low-alloy (HSLA) steel. This study focuses on the effect of welding parameters on the microstructure, tensile response, microhardness, and weld bead profile. For this purpose, a factorial experimental design was formed, covering a heat input range from 53 to 75 J/mm. This study identified the main effects and interactions of welding speed and laser power on the weld bead profile and on its width. The microstructure, weld bead width, hardness, and tensile mechanical properties were significantly influenced by heat input. Furthermore, numerical simulations on real weld bead profiles revealed high values of the stress concentration factor and suggested a correlation with heat input.

Insight into stress corrosion cracking in heat-affected zone of Nb micro-alloyed high-strength low-alloy steel in SO2-polluted seawater

Insight into stress corrosion cracking in heat-affected zone of Nb micro-alloyed high-strength low-alloy steel in SO2-polluted seawater

Impact of boron and titanium on the mechanical properties and recrystallization behaviour of low carbon cold rolled and batch annealed HSLA steels

This study investigates the impact of boron (B) on the mechanical properties and recrystallization behaviour of cold rolled and batch-annealed titanium (Ti) microalloyed high-strength low-alloy (HSLA) steels. HSLA steels are essential in industries such as automotive and construction due to their superior mechanical properties and cost-effectiveness. The addition of microalloying elements, particularly Ti, has shown significant promise in enhancing these properties through mechanisms like precipitation strengthening and controlled recrystallization. However, the role of B in this context remains underexplored. Here, three alloy compositions were systematically examined: a reference low carbon steel base alloy with no Ti or B (Ref), the base alloy with added Ti (Ref + Ti), and the base alloy with both Ti and B additions (Ref + Ti + B). The findings showed that microalloying with Ti + B can provide excellent strength improvements in the hot rolled strip, mainly due to increased hardenability that promotes the formation of finer ferrite grains with a high dislocation density. However, the recovery and recrystallization behaviour is such that it is not possible to reproduce these benefits after cold rolling and batch annealing, highlighting the complexity of optimizing microalloying strategies for cold-rolled and batch annealed products. The insights gained from this study provide a deeper understanding of the mechanisms governing the recrystallization of Ti and B microalloyed HSLA steels, paving the way for the development of advanced materials with tailored properties for critical applications.

Assessing strength of ferrite and martensite in five dual phase and two martensitic steels via high throughput nanoindentation to elucidate origins of strength

This paper describes the main findings from an experimental investigation into overall and local strength of four dual-phase (DP) steels classified based on their tensile strength (TS) levels from DP590, to 780, to 980, to 1180, a martensitic steel (MS) 1700, and a high-strength low-alloy (HSLA) steel in rolled and additively manufactured (AM) conditions. The DP steels and the MS steel consist of ferrite and martensite, while the HSLA steel is solely martensitic. High throughput nanoindentation mapping is employed to measure the mechanical hardness of individual phases contributing to strength of the steels. A clustering methodology for correlating measured hardness and phase maps is conceived to infer hardness per phase. With increasing fractions of martensite, the hardness values of both ferrite and martensite are found to increase with more rapid increase in the hardness of ferrite than martensite. The phases increasingly dislocate with the fraction of martensite as rationalized by crystal plasticity modeling of strength of the steels. Initial slip resistances and a set of hardening parameters associated with the slip in ferrite and martensite are established to model the flow stress behavior of the steels. In modeling the co-dependent nature of crystallographic slip in ferrite and martensite, the initial dislocation densities are inferred and correlated with the measured hardness values. The hardness of martensite in the rolled HSLA steel is comparable to the hardness of martensite in the MS steel, while martensite in the AM HSLA steel is softer owing to the tempering occurring during the AM process.

Modeling of Dynamic Recrystallization Kinetics of a High Strength Low Alloy Steel During Hot Rolling

Modeling of Dynamic Recrystallization Kinetics of a High Strength Low Alloy Steel During Hot Rolling

Experimental investigation and numerical simulation of swaging process of tubes for oil country tubular goods

AbstractPremium integrated seamless pipes made from high strength low alloy steels are used to produce oil country tubular goods. Operational requirements of these pipes in petroleum industry lead to an adequate tube end connection with better mechanical strength and sealing properties. Therefore a cold swaging process or calibration of pipe end is necessary for the mechanical threading process of the tube. Applications of typical calibration mandrels result in heavy wear due to higher swaging loads and the optimal necessary geometry of end tube could not be achieved. In this study, a new mandrel geometry with a finished surface was developed to modify the pipe end profile and reduce the wear tool. The investigated pipe made from P110- pipe steel was plastically preformed using a cold swaging process. Experimental measurements of the pipe end geometry after swaging process resulted an increase of the inner tube diameter of approximately 4.9% and an outer tube diameter of 3.7% respectively. Furthermore, a rather constant tube wall thickness was also observed. An Abaqus plug-in was developed to characterize the swaging process of pipe ends. The influence of friction between tool and pipe surfaces on the final geometry of pipe ends and residual stresses in pipe ends due to preforming were numerically predicted. The new designed swaging process resulted a better final pipe end geometry and low tool wear during the preforming of pipe end. The presented plug-in in this work could be used for tool optimization and characterization of swaging process of pipes in oil and gas industries.

Mechanical and Metallurgical Characteristics of Wire-Arc Additive Manufactured HSLA Steel Component Using Cold Metal Transfer Technique

Recently, the application of wire-arc additive manufacturing (WAAM) for the production of metallic products is gaining traction. WAAM is associated with the direct energy deposition technique and therefore has a higher deposition rate (approximately 4 kg/h). For this reason, it is of greater interest than powder-based additive manufacturing techniques. Industrial applications such as marine and offshore structures and pressure vessels for space programs commonly utilize high-strength low-alloy (HSLA) steel. HSLA steel components produced by casting methods exhibit defects due to oxidation. Therefore, cold metal transfer (CMT)-WAAM was adopted in this study to fabricate HSLA steel components. The metallurgical properties were analyzed using microscopic and diffraction techniques. The effects of the evolved microstructures on mechanical properties, such as strength, microhardness, and elongation to fracture, were evaluated. To analyze and test the structure, two regions were selected, namely, top and bottom. Microstructural analyses revealed that both regions were primarily composed of acicular ferrite, polygonal ferrite, and bainitic structures. The bottom region exhibited superior mechanical properties compared with the top region. The improved strength at the bottom region can be ascribed to the formation of a high density of dislocations and finer grains.

Effects of heat input on microstructure evolution and corrosion resistance of underwater laser cladding high-strength low-alloy steel coating

The effects of heat input on the microstructure evolution and corrosion resistance of the high-strength low-alloy (HSLA) steel coating obtained by wire-feed underwater laser cladding were studied. Optical digital microscope, scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), transmission electron microscope (TEM), electron back-scattered diffraction (EBSD), electrochemical tests, laser microscope and other characterization methods were used. As the heat input increased, the smoothness of the underwater cladding coating improved, with little changes in elemental distribution and phase composition. However, the content of acicular ferrite increased, while the amounts of lath bainite, lath martensite, and granular bainite decreased. As the heat input increased from 0.4 to 0.55 kJ/mm, the grain size increased from 25.3 to 55.9 μm, the proportion of low-angle grain boundaries rose from 61.3 % to 69.1 %, and the texture intensity of the (110) crystal plane increased from 16.22 to 23.83. Meanwhile, the dislocation density decreased from 4.9 × 1014 to 4.1 × 1014 m−2. These changes enhanced the corrosion resistance of underwater coating. As the heat input increased from 0.4 to 0.55 kJ/mm, the corrosion current density decreased from 2.13 × 10−5 to 3.35 × 10−6 A/cm2, and the corrosion potential increased from −0.823 to −0.529 V. Additionally, the depth-to-width ratio of the corrosion pits decreased from 0.255 to 0.053. This study laid the foundation for high-quality in-situ underwater repairs of ships and submarines made of high-strength steel.

Hot deformation behavior and microstructural evolution of high-carbon high-strength low alloy steel

This study investigates the hot deformation behavior, microstructural evolution, and processing map of a high-carbon high-strength low alloy steel subjected to hot compression tests in the temperature range of 850 °C–1150 °C and strain rates from 0.01 s⁻1–10 s⁻1. A highly accurate flow stress constitutive equation has been established and the activation energy of the experiment steel is 462.6 kJ/mol. Processing maps were generated to identify unstable zones, low-power dissipation zones, and optimum processing zones, accompanied by detailed discussions on corresponding microstructures and mechanical properties. The recommended hot deformation parameters at a true strain of 0.9 are temperatures from 944 °C to 1050 °C and strain rates from 0.01 s⁻1 to 0.52 s⁻1 according to the processing map. The effects of deformation temperature and strain rate on the microstructure were then investigated. It is revealed that reducing deformation temperature and increasing strain suppress the recrystallization process and the growth of recrystallized grains; while VC precipitation is suppressed under high temperatures and high strain rates.

Specifics of Experimental and Fem Approaches in Structural Integrity Assesment of Penstock Made of HSLA Steel

Taking into account the history of problems concerning high-strength low-alloyed (HSLA) steel used for manufacturing of penstocks (partly presented by authors in previous studies), this paper is oriented toward specifics on structural integrity assessment of construction in question. Experimental testing of parent material, i.e. HSLA steel, such as microstructure analysis, impact toughness testing and hardness measuring provide insight into characteristics of parent material properties. Considering geometry of penstock and specific requirements, finite element method (FEM), i.e. ABAQUS, was used to assess the structural integrity of penstock as a whole, specific the longitudinal welded joint under the different internal (working) pressure. It should be emphasized that a slight undermatching effect was investigated by FEM approach in this case. Focus is being put on plastic deformation investigation on aforementioned welded joint under maximum internal pressure of 120 bar.

Achieving 1.7 GPa Considerable Ductility High-Strength Low-Alloy Steel Using Hot-Rolling and Tempering Processes.

To achieve a balanced combination of high strength and high plasticity in high-strength low-alloy (HSLA) steel through a hot-rolling process, post-heat treatment is essential. The effects of post-roll air cooling and oil quenching and subsequent tempering treatment on the microstructure and mechanical properties of HSLA steels were investigated, and the relevant strengthening and toughening mechanisms were analyzed. The microstructure after hot rolling consists of fine martensite and/or bainite with a high density of internal dislocations and lattice defects. Grain boundary strengthening and dislocation strengthening are the main strengthening mechanisms. After tempering, the specimens' microstructures are dominated by tempered martensite, with fine carbides precipitated inside. The oil-quenched and tempered specimens exhibit tempering performance, with a yield strength (YS) of 1410.5 MPa, an ultimate tensile strength (UTS) of 1758.6 MPa, and an elongation of 15.02%, which realizes the optimization of the comprehensive performance of HSLA steel.

New insights from crystallography into the effect of Ni content on ductile-brittle transition temperature of 1000 MPa grade high-strength low-alloy steel

The significant effect of Ni content (0.92, 1.94 and 2.94 wt%) on ductile-brittle transition temperature (DBTT) and microstructure in a 1000 MPa grade high-strength low-alloy (HSLA) steel was studied. Using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), Charpy impact test and low-temperature tensile test to study the fundamental reasons for the effect of Ni content on toughness. The results indicated that increasing the Ni content can reduce the DBTT of HSLA steel and improve the impact toughness at low temperatures. EBSD data post-processing analysis revealed that the key reason for the increase in low-temperature toughness is the refinement of the microstructural crystallographic structure, specifically the significant increase in the boundary density of the block and packet. With the increase of Ni content, the density of grain boundary with an orientation difference greater than 5° between two adjacent {110} crystal planes was higher, which can form a higher density of dislocation pile-up group, thus better reducing local stress concentration. Meanwhile, the stacking fault energy (SFE) increases with the increase of Ni content, which made the screw dislocation more prone to cross slip at low temperature, resulting in an increase in plasticity at low temperatures. These observed phenomena and reasons provided a theoretical explanation for the role of Ni content in reducing DBTT and enhancing the toughness of the core in heavy gauge plates.

Microstructure evolution and constitutive modeling of Cu-bearing high-strength low-alloy steel during hot deformation

The microstructural evolution of austenite during hot deformation determines the mechanical properties of steel products. Consequently, industrial applications necessitate a thorough comprehension and modeling of this process. Under varied hot deformation conditions, the flow stress, microstructure evolution, and constitutive modeling of a Cu-bearing steel were examined. At various temperatures and strain rates, compression experiments are conducted, and the resulting microstructures were studied by electron backscatter diffraction (EBSD). Our results indicate that fine prior austenite grains with an average diameter of 22.1 m and a high-angle grain boundary density of 0.25 m1 were produced at a deformation temperature of 950 °C and a strain rate of 1 s−1. The dominating rotating cube components ({001}<110>) in the sample deformed at 1150 °C were gradually replaced by the γ-fiber texture component as the deformation temperature decreased. To accurately predict the flow behavior of this steel, we proposed an improved Arrhenius constitutive model that accounts for strain rate and adiabatic temperature rise. With a correlation coefficient (Rc) of 0.9936, a root mean square error (RMSE) of 4.92%, and a relative error (δ) of 6.05 MPa, our results demonstrate that this model predicts the flow stress of the experimental steel with good precision. This research contributes to the development of high-performance steel products by shedding light on the microstructural evolution and flow behavior of Cu-containing steels under hot deformation conditions.