Longitudinal Field Research Articles

Use of molybdenum as a pressure calibrant in a cubic press and sound velocity measurement of tungsten to 5 GPa

ABSTRACT The pressure limit of the conventional cubic press is normally below 6 GPa, and the suitable pressure calibrant of the fixed-point method is scarce. In this study, we developed a new method for pressure determination using an acoustic travel time approach. Based on the reported ultrasonic travel times of polycrystalline molybdenum under high pressure in literature, an acoustic gauge of polycrystalline molybdenum was derived. The shear wave travel times of molybdenum were measured at high pressures and utilized for the pressure calibration in a cubic press. The pressures derived from this new travel time method are in excellent agreement with those from the fixed-point method. Subsequent compressional and shear wave velocities of polycrystalline tungsten were measured up to about 5 GPa at room temperature to further verify this method. This travel time method for pressure calibration is valuable for the sound velocity measurement of other materials in an offline laboratory.

Eect of acid corrosion on physico-mechanical parameters and energy dissipation of granite

In deep underground engineering, it is inevitable that portions of the rock mass will be subjected to the erosion and chemical corrosion of infiltrating water. A comprehensive study of the physical, mechanical, and energetic properties of rocks after hydrochemical corrosion is crucial for ensuring the stability of the rock mass. The novelty of this research lies in the detailed investigation of the macroscopic and microscopic morphologies of rocks exposed to various corrosive solutions, as well as the changes in various physical and mechanical parameters. Utilizing the weighting method, a scientific comprehensive evaluation system for deep rocks after hydrochemical corrosion has been established. The results indicate a pronounced sensitivity of the macroscopic and microscopic morphologies to pH values. The longitudinal wave velocity of the corroded rock decreases obviously, with the maximum decrease being 13.46%. As the pH value decreases (from 7 to 3), the compressive strength, elastic modulus, cohesion, and internal friction angle of the rocks all decrease significantly. The acidity of the solution significantly aects the changes in the three types of strain energy of the rocks, with higher acidity leading to weaker energy storage capability. Among the factors influencing the characteristics of strain energy variation in rocks, confining pressure has a higher priority than pH value. This study precisely evaluates the impact of hydrochemical corrosion on rock damage using a percentage-based scoring system, and found that granite’s score dropped from 81 to 16. The research findings provide valuable insights for the evaluation of rock mass stability under hydrochemical corrosion conditions.

Research on ultrasonic synchronous detection method for material residual stress and thickness

Being limited to the different transmission and reception modes and detection signals of the critical refracted longitudinal wave method for stress measurement and the perpendicular incident echo method for thickness measurement, it is necessary to use different probes and equipments when simultaneously measuring stress and thickness. For this difficulty, the acquisition frequency and the number of bits are taken as the research object to realize the optimization of the echo signal. By combining FEM simulations with Comsol software with experimental research, the effects of probe incidence angle, probe spacing, and temperature on ultrasonic waves are investigated, and the relationship between probe spacing and the stress coefficient of measured component (K) is analyzed. A novel ultrasonic synchronous detection method for residual stress and thickness is proposed. This method is based on an integrated transmit-receive probe with oblique incidence, utilizing critical refracted longitudinal wave (LCR wave) for stress detection and synchronously generated transverse waves for thickness measurement. For the first time, a formula for ultrasonic thickness measurement based on inclined incidence is derived. Using self-developed equipment, ultrasonic testing experiments on step test block and cantilever beam loading device were conducted to verify the accuracy and precision of the proposed synchronous detection method for stress and thickness. This method has significant application prospects in the inspection or online monitoring of pressure vessels concerned with fatigue and corrosion performance.

Acoustic and acousto-optic properties of Ga10Ge15Te75 glass

The acoustic and acousto-optic (AO) properties of the Ga10Ge15Te75 glass, which is promising for creation of AO devices operating with the near and middle infrared optical radiation, are studied. In this paper, the experimental results for the longitudinal and shear acoustic waves phase velocities and the AO figure of merit (M2) in case of isotropic diffraction by these waves are presented. All measurements are carried out for the 3.39 µm optical wavelength. The obtained M2 magnitudes turned out to be close to 1000·10–15s3/kg that significantly exceeds the typical values observed in germanium (Ge) crystal – the basic material for middle infrared AO devices fabrication. The experimentally determined longitudinal acoustic wave attenuation coefficient for 100 MHz ultrasound frequency turns out to be 1.32 ± 0.05 cm-1. Finally, the acoustic and AO properties of telluride based glasses with the close chemical composition, namely Ga10Ge15Te75, Si25Te75 and Ge25Se15Te60 glasses, are compared.

SPIRou observations of the young planet-hosting star PDS 70

Abstract This paper presents near-infrared spectropolarimetric and velocimetric observations of the young planet-hosting T Tauri star PDS 70, collected with SPIRou at the 3.6-m Canada-France-Hawaii Telescope from 2020 to 2024. Clear Zeeman signatures from magnetic fields at the surface of PDS 70 are detected in our data set of 40 circularly polarized spectra. Longitudinal fields inferred from Zeeman signatures, ranging from −116 to 176 G, are modulated on a timescale of 3.008 ± 0.006 d, confirming that this is the rotation period of PDS 70. Applying Zeeman-Doppler imaging to subsets of unpolarized and circularly polarised line profiles, we show that PDS 70 hosts low-contrast brightness spots and a large-scale magnetic field in its photosphere, featuring in particular a dipole component of strength 200–420 G that evolves on a timescale of months. From the broadening of spectral lines, we also infer that PDS 70 hosts a small-scale field of 2.51 ± 0.12 kG. Radial velocities derived from unpolarized line profiles are rotationally modulated as well, and exhibit additional longer-term chromatic variability, most likely attributable to magnetic activity rather than to a close-in giant planet (with a 3-σ upper limit on its minimum mass of ≃4 at a distance of ≃0.2 au). We finally confirm that accretion occurs at the surface of PDS 70, generating modulated red-shifted absorption in the 1083.3-nm He i triplet, and show that the large-scale magnetic field, often strong enough to disrupt the inner accretion disc up to the corotation radius, weakens as the star gets fainter and redder (as in 2022), suggesting that dust from the disc more easily penetrates the stellar magnetosphere in such phases.

The Peculiarities of Acoustic Normal Waves Propagation in Thin Porous Sheets of Thermally Expanded Graphite

Thermally expanded graphite belongs to a new class of graphite materials with unique physical, chemical and mechanical properties. Acoustic wave velocity is one of the most important characteristics for study of porous materials including thin porous sheets of thermally expanded graphite. In this paper peculiarities of symmetric mode S0 Lamb wave propagation and SH-wave with horizontal polarization in sheets of thermally expanded graphite are experimentally investigated. To determine their velocities a differential measurement scheme on the base of a low-frequency acoustic flaw detector DIO1000 LF and specialized piezoelectric transducers with dry point contact was used. Additionally the longitudinal wave velocity in direction of sheet thickness was determined using piezoelectric transducers based on polyvinylidene fluoride. Indicatrices of normal wave velocities in the rolling plane were plotted and it was shown that the maximum acoustic anisotropy is characteristic for the S0-mode. The velocity minimum corresponds to the longitudinal direction of the rolling plane in which the maximum elongation of gas pores was observed. Influence of thickness and density of thermally expanded graphite sheets on the velocities of normal waves was investigated and presence of the thickness range where the minimum velocity values were observed due to the maximum inhomogeneity of layers formed in the rolling process. Method for determination of dynamic elastic moduli of porous thermally expanded graphite sheets using experimentally measured velocities of normal waves was proposed. It was shown that in the longitudinal direction of the rolling plane the Poisson's ratio took negative values which allow to attribute the specified material to auxetics ones.

Propagation, reflection, and transmission of nonlocal waves at the interface between semiconductor isotropic and diffusive porous semiconductors through a higher-order fractional derivative study

The current research paper investigates the transmission of nonlocal waves occurring at the interface between a semiconductor isotropic medium and a diffusive porous solid. A higher-order fractional-order derivative heat conduction model is utilized to account for thermal effects on wave propagation, reflection, and transmission. The interface generates five coupled and one independent transmitted wave in the lower medium, along with three coupled transmitted waves and one independent SV wave. Graphical analyses are conducted to examine the propagation speed of reflected waves in both porous and non-porous media. The impact of elastic non-locality and the fractional-order parameter on the propagation speed of all waves within the media is also assessed. The amplitude ratios are computed for the incident longitudinal displacement wave at the free boundary. The research explores the influence of physical parameters on reflection and transmission coefficients, and the results are validated through the conservation of energy. Additionally, the analysis yields deductions for certain special cases.

Recycle right: How to decrease recycling contamination with informational point-of-disposal signage

AbstractPlastic pollution represents a grand challenge facing society, yet the amount of plastic being recycled is only about 5%. This recycling crisis has intensified with the growing problem of recycling contamination (i.e., incorrect placement of unrecyclable materials in recycling receptacles). This research investigates the potential for informational point-of-disposal recycling signage to decrease recycling contamination. In a longitudinal field study and three experiments, the authors demonstrate that providing schema-congruent prescriptive information (“Recycle these items”) does not reduce recycling contamination and may inadvertently lead to over-recycling. In contrast, the presence of proscriptive information that is moderately incongruent with established schemas (“Do not recycle these items”) prompts more effortful, piecemeal processing. This encourages individuals to integrate the information into their recycling decisions, diminishing their dependence on pre-existing beliefs and expectations regarding recycling and, consequently, lowering contamination rates. Recycling expertise is found to moderate the effects of point-of-disposal recycling signage. By examining such nuanced recycling communication strategies, this research aims to shift the conversation from “recycle more” to “recycle right.”

Tilted columnar metal film as transducer of transverse coherent acoustic phonons in picosecond acoustics

Picosecond acoustics has been widely used to study thin film elasticity, hypersound attenuation, and adhesion of thin films to substrates. A major limitation of the technique is its restriction to only longitudinal waves. Although work has been reported on the ultrafast generation and detection of transverse waves, a general method compatible with thin films deposited on silicon is still missing. In this work, we show that by depositing a tilted columnar metal film and using an optical detection sensitive to light polarization, it is possible to excite and detect optically both types of bulk acoustic waves in thin films. The protocol is first established on metalized glass substrates, then applied to a range of transparent films deposited on silicon (silica, AlN, AlScN, and SiC). In each case, Brillouin oscillations are detected at two frequencies, one being the longitudinal mode, the other the transverse. The film thickness and two sound velocities are measured in each thin film. Transverse coherent phonons as high as 116 GHz are observed in the SiC thin film.

Research on ultrasonic testing method for tangential contact stress based on equivalent medium theory

As a weak link, the joint surface of machine tools directly affects the stiffness and machining accuracy of the entire machine tool. However, obtaining the distribution of contact stress is a key problem that urgently needs to be solved in exploring the mechanical properties of joint surface connections. In this paper, a tangential contact stress ultrasonic testing method based on the equivalent medium theory is proposed, providing data support for accurately characterizing the contact state of the joint surface. A virtual material model of rough contact interface based on fractal theory is established to explore the coupling relationship between the propagation speed of ultrasonic critical refracted longitudinal waves, the tested object’s material parameters, and stress. Moreover, the expression of the equivalent material parameters of the ultrasonic critical refracted longitudinal wave propagation layer with stress variation is derived. An ultrasonic acoustic time difference model considering changes in contact surface material parameters is constructed based on the principle of acoustic elasticity of ultrasound. Furthermore, a critical refractive detection model for longitudinal wave’s tangential contact stress is established based on equivalent medium theory. Experimental specimens and stress detection plans are designed, and the tangential contact stress of the specimens is measured based on the division of surface grids. The equivalent stress value of each node is calculated based on the von Mises stress by measuring the stress in the X/Y direction. In addition, a shear stress distribution cloud map of the contact surface is drawn. Finally, the accuracy of the detection results is confirmed by combining theory, simulation, and experimental methods. The proposed tangential contact stress detection method based on critical refractive longitudinal waves is significant for low-stress assemblies.

Characterizing a device for easy simulation of compression waves induced by trains passing through tunnels

When a high-speed train enters a tunnel, an initial compression wave (ICW) is generated, which radiates out as it propagates lengthways through the tunnel to the exit, forming an uncomfortable micro-pressure wave (MPW). The aim of this research is to develop a scaled device to quickly simulate this aerodynamic phenomenon. Our device achieves this by using the instantaneous release of high-pressure air in the chamber. In the first part of the paper, the reliability of this device is verified by various methods, including an airtightness check, calibration of transducers, and repeatability experiments. Next, the mapping of the parameters of the device to engineering values is discussed. The propagation process of the ICW and the pressure fluctuations in the tunnel are then analyzed, and the discussion centers around a control variable case. Finally, the MPW generated near the tunnel exit is explored and acoustically evaluated. It is found that the initial pressure in the chamber, the opening voltage, and the number of solenoid valves in the experiment can be mapped to the train speed, the characteristic length of train nose, and the blockage ratio, respectively. When the pressure amplitude of the ICW is higher, there will be a certain steepening phenomenon in the propagation process. The pressure fluctuation cycle in the tunnel is calculated as 4× tunnel length/wave velocity, and the amplitude of fluctuation decays exponentially over the cycles. In most cases, the sound pressure level of MPWs near the tunnel exit exceeds the hearing threshold, based on the auditory properties of the human ear.

Band edge modulation for high-performance LL-SAW resonators on LiNbO3/SiC by introducing an ultra-thin intermediate oxide layer

With the exploding demand of rapid information transmission, high-frequency acoustic filtering devices are becoming an immediate need. Longitudinal leaky surface acoustic wave (LL-SAW) devices with unique advantages can be a promising platform. In this paper, we introduce a 100 nm intermediate oxide layer into the X-cut lithium niobate on silicon carbide (LiNbO3/SiC) to improve the in-band performance of LL-SAW resonators. First, the dispersion curves of the structures are analyzed by finite element method. In this part, we successfully interpret the intrinsic low quality factor (Q) of LL-SAW on LiNbO3/SiC in general design, and predict the enhancement of Q by introducing an intermediate oxide layer without degradation on spurious response. Then, one port resonators considered in the simulation are fabricated and measured. As a result, enhancements in Bode Q among the whole passband are confirmed. Compared with devices state of art, resonators with leading performances are demonstrated. The fabricated resonators have peak-valley admittance ratio of 63.87 dB, Bode Q of ∼300 at fr and ∼530 at far, keff2of 15.66 % and phase velocity of 6187.3 m/s. Additionally, the resonant frequency of SH1 mode shifts to higher frequency. This work enables the design of next generation high frequency mobile communication filters.

Numerical study on micro-fracture mechanism of rock dynamic failure induced by abrupt unloading under high in-situ stresses

Rock burst is a kind of severe engineering disaster resulted from dynamic fracture process of rocks. The macro failure behaviors of rocks are primarily formed after experiencing the initiation, propagation, and coalescence of micro-cracks. In this paper, the grain-based discretized virtual internal bond model is employed to investigate the fracturing process of unloaded rock under high in-situ stresses from the micro-fracture perspective. The simulated micro-fracturing process reveals that the longitudinal stress waves induced by unloading lead to the visible unloading effect. The influences of in-situ stresses, mineral grain sizes, and grain heterogeneity on rock macro and micro fracture are investigated. Micro-crack areas of tensile and shear cracks and micro-crack angles are statistically analyzed to reveal the rock micro-fracture characteristics. The simulated results indicate that the combined effect of the stress state transition and the unloading effect dominates the rock unloading failure. The vertical and horizontal in-situ stresses determine the stress state of surrounding rock after unloading and the unloading effect, respectively. As the vertical stress increases, the stress level after unloading is higher, and the shear failure characteristics become more obvious. As the horizontal stress increases, the unloading effect increases, leading to the intensification of tensile failure. The mineral grain size and grain heterogeneity also have nonnegligible influences on rock unloading failure. The micro-fracture perspective provides further insight into the unloading failure mechanism of deep rock excavation.

Electrotunable superlubricity of two-dimensional ZIF-8

Electric field control can actively, dynamically, and repeatably influence the interface friction behavior. The unique properties of two-dimensional (2D) ZIF-8 make it a promising lubricating material for electromechanical devices. The study on the electrotunable superlubricity of 2D ZIF-8 is carried out under longitudinal and transverse electric fields respectively, resulting in an order of magnitude variation in friction coefficient (μ: 0.0037∼0.0124). Through the experiments and simulation, the regulation mechanism of electric fields on the lubricating properties of 2D ZIF-8 is attributed to the coupling effect of adhesion regulation and out-of-plane deformation regulation: The weakening of anchoring effect reduces the adhesion between probe and 2D ZIF-8; the tight binding of interfacial charge under longitudinal electric field as well as the increase in surface stiffness caused by lattice tension under transverse electric field, both restrain the out-of-plane deformation during friction. The electrotunable superlubricity of 2D ZIF-8 helps achieve rapid and flexible adjustment of the friction interface in electro-mechanical systems under charged conditions, illuminating the future development prospects for intelligent control.

The propagation characteristics of a detonation wave in uniformly premixed gases within a semi-confined channel

Based on the OpenFOAM platform, a numerical study was conducted to investigate the propagation characteristics of a detonation wave in uniformly premixed gases within a semi-confined channel, specifically examining the changes in wave's structure and analyzing the detonation reinitiation-extinguishment process. The results indicate that, due to the weak confinement, the detonation wave experiences lateral expansion, with transverse waves on the detonation wave front penetrating into the inert gas and forming segmented protrusions on the oblique shock wave. During the propagation process, the number of transverse waves decreases gradually, and the reflected waves formed by the interaction between transverse waves and the inert gas are weak, collectively leading to a gradual decay in the strength of the detonation wave and a reduction in the frequency of pressure oscillation on the detonation wave front. Furthermore, when transverse waves interact with the inert gas and undergo Mach reflection, the reflected waves would detach the inert gas and form new transverse waves promoted by upward-moving old transverse waves and disturbances on the flame front, thereby extending the duration distance of the detonation wave. Subsequently, after the detonation wave decouples, a transverse wave reflected from the inert gas interface interacts with the lower wall, triggering local detonation reinitiation, which generates a higher-intensity longitudinal wave that couples with the leading shock wave, temporarily restoring the detonation wave and forming lateral detonation in the decoupled region. However, the detonation wave will ultimately extinguish due to the attenuation of transverse waves' intensity and decreasing number of these waves.

Gender and Job Satisfaction: Examining the Role of Leadership Behavior and Gender Congruence Over Time

This article examines the longitudinal relationships between leader gender, leadership style, gender congruence between leaders and followers, and employee job satisfaction over time. Drawing on gender stereotype and role congruity theories, it reviews how communal attributes ascribed to females can initially disadvantage women in leadership roles by compromising their perceived competence. However, evidence indicates such bias may fade as individuals gain experience observing a leader's actual behaviors, values and competencies through ongoing interactions. Specifically, a five-year longitudinal field study found women leaders initially received marginally lower evaluations than men but ended with equal or higher ratings as preconceptions diminished. Additionally, demonstrating a transformational leadership style emphasizing inspiration and development associated positively with follower well-being across genders and leader-follower gender alignments. Practically, organizations that implement regular assessment and mentoring activities appear most effective at fostering truly inclusive cultures where talent, not attributes, drive satisfaction and career outcomes long-term.

Lessons From 3 Longitudinal Sensor-Based Human Behavior Assessment Field Studies and an Approach to Support Stakeholder Management: Content Analysis.

Pervasive technologies are used to investigate various phenomena outside the laboratory setting, providing valuable insights into real-world human behavior and interaction with the environment. However, conducting longitudinal field trials in natural settings remains challenging due to factors such as low recruitment success and high dropout rates due to participation burden or data quality issues with wireless sensing in changing environments. This study gathers insights and lessons from 3 real-world longitudinal field studies assessing human behavior and derives factors that impacted their research success. We aim to categorize challenges, observe how they were managed, and offer recommendations for designing and conducting studies involving human participants and pervasive technology in natural settings. We developed a qualitative coding framework to categorize and address the unique challenges encountered in real-life studies related to influential factor identification, stakeholder management, data harvesting and management, and analysis and interpretation. We applied inductive reasoning to identify issues and related mitigation actions in 3 separate field studies carried out between 2018 and 2022. These 3 field studies relied on gathering annotated sensor data. The topics involved stress and environmental assessment in an office and a school, collecting self-reports and wrist device and environmental sensor data from 27 participants for 3.5 to 7 months; work activity recognition at a construction site, collecting observations and wearable sensor data from 15 participants for 3 months; and stress recognition in location-independent knowledge work, collecting self-reports and computer use data from 57 participants for 2 to 5 months. Our key extension for the coding framework used a stakeholder identification method to identify the type and role of the involved stakeholder groups, evaluating the nature and degree of their involvement and influence on the field trial success. Our analysis identifies 17 key lessons related to planning, implementing, and managing a longitudinal, sensor-based field study on human behavior. The findings highlight the importance of recognizing different stakeholder groups, including those not directly involved but whose areas of responsibility are impacted by the study and therefore have the power to influence it. In general, customizing communication strategies to engage stakeholders on their terms and addressing their concerns and expectations is essential, while planning for dropouts, offering incentives for participants, conducting field tests to identify problems, and using tools for quality assurance are relevant for successful outcomes. Our findings suggest that field trial implementation should include additional effort to clarify the expectations of stakeholders and to communicate with them throughout the process. Our framework provides a structured approach that can be adopted by other researchers in the field, facilitating robust and comparable studies across different contexts. Constantly managing the possible challenges will lead to better success in longitudinal field trials and developing future technology-based solutions.

Seismic Vulnerability Assessment of the Cliff-Attached Buildings Equipped with Energy Dissipation Devices Under Obliquely Incident Seismic Waves

Cliff-attached structures are structures attached to slopes and connected tightly, which is particularly complex to analyze due to the foundations’ unequal grounding and the lateral stiffness’ irregularity. In rare earthquakes, seismic waves are usually obliquely incident on the foundation at a certain angle. Therefore, it is not appropriate to consider only seismic waves’ vertical incidence, and it is necessary to consider multi-angle oblique incidence. In this paper, based on the theory of viscous-spring artificial boundary and the principle of equivalent nodes at the interface of oblique incidence of ground shaking P-waves, and combined with the dynamic properties related to Buckling-Restrained Brace, the numerical models of slopes and two kinds of cliff-attached structures considering the slope amplification effect and soil-structure interaction are established. The dynamic response of the obliquely incident seismic waves under the action of the cliff-attached vibration reduction structure is studied in depth, and the additional effective damping ratios of the nonlinear energy-dissipated units based on the deformation energy are compared and analyzed. It is shown that under the four oblique incidence angles of incidence (compression waves in the vertical plane) studied in this paper, the seismic dynamic response and damage degree peaked at an angle of incidence of 60°, with a tendency to increase and then decrease with increasing angles of incidence. The ability of an energy-dissipating vibration reduction device to change structural vibration characteristics decreases with an increase in incidence angle. The difference between the total strain energy of the structure in the X-direction (Transverse slope direction) and Y-direction (Down-slope direction) and the total energy dissipation of the dissipative components is obvious, with the X-direction being about 10 times that of the Y-direction.

Mothers’ Parenting Behaviours, Strain, Enjoyment and Subsequent Childbearing

Modern parenting is both emotionally costly and rewarding. It is also more intensive than before and requires significant time and effort, particularly from mothers. Emotional costs and benefits of children are important to fertility decisions, and they may be linked with a mother’s parenting behaviours. Using a sample of 4402 partnered first-time mothers from the UK Household Longitudinal Study waves 1 to 9 (2009–2018), this study investigated the association between mothers’ parenting behaviours, changes in the levels of reported strain or enjoyment of everyday activities and second-birth transition. A decline in enjoyment formed a negative association with second-birth risk. The frequency of participation in dinner with the child and in leisure activities with the child formed significant associations with second-birth risk but only for selected segments of the population. We discuss the possible underlying mechanisms of these associations and the socioeconomic differences within them.

Ultra-Low Frequency Waves of Foreshock Origin Upstream and Inside of the Magnetospheres of Earth, Mercury, and Saturn Related to Solar Wind–Magnetosphere Coupling

This review examines ultra-low frequency (ULF) waves across different planetary environments, focusing on Earth, Mercury, and Saturn. Data from spacecraft missions (CHAMP, Swarm, and Oersted for Earth; MESSENGER for Mercury; and Cassini for Saturn) provide insights into ULF wave dynamics. At Earth, compressional ULF waves, particularly Pc3 waves, show significant power near the equator and peak around Magnetic Local Time (MLT) = 11. These waves interact complexly with Alfvén waves, impacting ionospheric responses and geomagnetic field line resonances. At Mercury, ULF waves transition from circular to linear polarization, indicating resonant interactions influenced by compressional components. MESSENGER data reveal a lower occurrence rate of ULF waves in Mercury’s foreshock compared to Earth’s, attributed to reduced backstreaming protons and lower solar wind Alfvénic Mach numbers, as ULF wave activity increases with heliocentric distance. Short Large-Amplitude Magnetic Structures (SLAMS) observed at Mercury and Saturn show distinct characteristics compared to those of Earth, including the presence of whistler precursos waves. However, due to the large differences in heliospheric distances, SLAMS (their temporal scale size correlate with the ULF wave frequency) at Mercury are significantly shorter in duration than at Earth or Saturn, since the ULF wave frequency primarily depends on the strength of the interplanetary magnetic field. This review highlights the variability of ULF waves and SLAMS across planetary environments, emphasizing Earth’s well-understood ionospheric interactions and the unique behaviours observed for Mercury and Saturn. These findings enhance our understanding of space plasma dynamics and underline the need for further research regarding planetary magnetospheres.