Linac Coherent Light Source II Research Articles

Overview of CW electron guns and LCLS-II RF gun performance

Various continuous-wave (CW) electron gun technologies are reviewed, including DC, superconducting radio frequency RF (SRF), hybrid DC-SRF and normal-conducting RF. Also, the SLAC Linac Coherent Light Source II (LCLS-II) normal-conducting RF gun and injector are described, and the performance to date, including the bunch emittance achieved and the dark current observed, is presented.

Enabling real-time adaptation of machine learning models at x-ray Free Electron Laser facilities with high-speed training optimized computational hardware

The emergence of novel computational hardware is enabling a new paradigm for rapid machine learning model training. For the Department of Energy’s major research facilities, this developing technology will enable a highly adaptive approach to experimental sciences. In this manuscript we present the per-epoch and end-to-end training times for an example of a streaming diagnostic that is planned for the upcoming high-repetition rate x-ray Free Electron Laser, the Linac Coherent Light Source-II. We explore the parameter space of batch size and data parallel training across multiple Graphics Processing Units and Reconfigurable Dataflow Units. We show the landscape of training times with a goal of full model retraining in under 15 min. Although a full from scratch retraining of a model may not be required in all cases, we nevertheless present an example of the application of emerging computational hardware for adapting machine learning models to changing environments in real-time, during streaming data acquisition, at the rates expected for the data fire hoses of accelerator-based user facilities.

Plasma cleaning of the SLAC Linac Coherent Light Source II high energy verification cryomodule cavities

Plasma cleaning is a technique that can be applied in superconducting radio-frequency (SRF) cavities in situ in cryomodules in order to decrease their level of field emission. We developed the technique for the Linac Coherent Light Source II (LCLS-II) cavities and we present in this paper the full development and application of plasma processing to the LCLS-II High Energy (HE) verification cryomodule (vCM). We validated our plasma processing procedure on the vCM, fully processing four out of eight cavities of this CM, demonstrating that cavities performance were preserved in terms of both accelerating field and quality factor. Applying plasma processing to this clean, record breaking cryomodule also showed that no contaminants were introduced in the string, maintaining the vCM field emission-free up to the maximum field reached by each cavity. We also found that plasma processing eliminates multipacting (MP) induced quenches that are typically observed frequently within the MP band field range. This suggests that plasma processing could be employed in situ in CMs to mitigate both field emission and multipacting, significantly decreasing the testing time of cryomodules, the linac commissioning time and cost and increasing the accelerator reliability.

Submacropulse electron-beam dynamics correlated with higher-order modes in a Tesla-type cryomodule

Experiments were performed at the Fermilab Accelerator Science and Technology (FAST) facility to elucidate the effects of long-range wakefields (LRWs) in TESLA-type superconducting rf cavities. In particular, we investigated the higher-order modes (HOMs) generated in the eight cavities of a cryomodule (CM) due to off-axis steering with correctors located ~4 m upstream of the CM. We have observed correlated submacropulse centroid slews of a few-hundred microns and centroid oscillations at ~240 kHz in the rf BPM data after the CM. The entrance energy into the CM was 25 MeV, and the exit energy was 100 MeV with 125 pC/b and 400 pC/b in 50-bunch pulse trains. These experimental results were evaluated for machine learning training aspects which will be used to inform the commissioning plan for the Linac Coherent Light Source-II injector CM.

Temporal shaping of narrow-band picosecond pulses via noncolinear sum-frequency mixing of dispersion-controlled pulses

A long-sought-after goal for photocathode electron sources has been to improve performance by temporally shaping the incident excitation laser pulse. The narrow bandwidth, short wavelength, and picosecond pulse duration make it challenging to employ conventional spectral pulse shaping techniques. We present a novel and efficient intensity-envelope shaping technique achieved during nonlinear upconversion through opposite-chirp sum-frequency mixing. We also present a numerical case study of the linac coherent light source-II photoinjector where transverse electron emittance is improved by at least 25%.

Commissioning of the SLAC Linac Coherent Light Source II electron source

For the Linac Coherent Light Source II (LCLS-II) project at SLAC, a 1.3 GHz superconducting rf (SRF) linac is being constructed that will generate 4 GeV electron bunches at a high repetition rate to drive x-ray free electron lasers. The LCLS-II electron source, which comprises the first three meters of the electron injector, includes two normal-conducting, continuous-wave rf cavities: a one-cell, 185.7 MHz gun and a two-cell, 1.3 GHz buncher. It also includes a gun load-lock system that allows photocathodes to be changed under vacuum. The components in this beam-line section were designed and built by Lawrence Berkeley National Laboratory based on experience from their advanced photoinjector experiment program. In combination with the SLAC UV laser system, the electron source is designed to produce beam rates up to 1 MHz with average currents up to $30\text{ }\text{ }\ensuremath{\mu}\mathrm{A}$ initially. The source was installed in mid-2018, well in advance of the SRF linac, which is now nearing completion. The source was commissioned over a two-year period, and this paper presents results including electron beam and dark current characterization.

Field emission mitigation studies in the SLAC Linac Coherent Light Source II superconducting rf cavities via in situ plasma processing

Field emission is one of the factors that can limit the performance of superconducting radio frequency cavities. In order to reduce possible field emission in LCLS-II (Linac Coherent Light Source II), we are developing plasma processing for 1.3 GHz 9-cell cavities. Plasma processing can be applied in situ in the cryomodule to mitigate field emission related to hydrocarbon contamination present on the cavity surface. In this paper, plasma cleaning was applied to single cell and 9-cell cavities, both clean and contaminated; the cavities were cold tested before and after plasma processing in order to compare their performance. It was proved that plasma cleaning does not negatively affect the nitrogen doping surface treatment; on the contrary, it preserves the high quality factor and quench field. Plasma processing was also applied to cavities with natural field emission or artificially contaminated. It was found that this technique successfully removes carbon-based contamination from the cavity iris and that it is able to remove field emission in a naturally field emitting cavity. Vacuum failure experiments were simulated on four cavities, and in some cases plasma processing was able to achieve an increase in performance.

Coherent x rays with tunable time-dependent polarization

We describe a method for producing high power, coherent x-ray pulses from a free electron laser with femtosecond scale periodic temporal modulation of the polarization vector. This approach relies on the generation of a temporal intensity modulation after self seeding either by modulating the seed intensity or the beam current. After generating a coherent temporally modulated $s$-polarization pulse, the electron beam is delayed by half a modulation period and sent into a short orthogonally oriented undulator, serving as a $p$-polarization afterburner. We provide simulations of three configurations for realizing this polarization switching, namely, enhanced self seeding with an intensity modulation generated by 2 color self seeding, enhanced self seeding of a current modulated bunch, and regular self seeding of a current modulated bunch. Start to end simulations for the Linac Coherent Light Source-II are provided for the latter.

RF heating in cavity-bellows of CW SRF cryomodule

In a cryomodule, bellows are commonly used to connect two adjacent superconducting cavities. It provides cavities a mechanical flexibility facilitating for thermal contraction or expansion during temperature transitions. While heat from superconducting cavities are removed from helium flowing through their jackets, non-superconducting bellows are cooled down through a relatively slow process of conduction cooling by adjacent superconducting cavities. An excessive heat deposition to the bellows could results in unsustainable rise in temperature that could lead to a thermal runaway. Because of the bellows proximity to the superconducting cavities, resulting thermal runaway could disrupt performance of the cavities and therefore, overall operation. For this reason, the paper presents a comprehensive assessment of RF heating resulting from most potent dynamic heating mechanisms in the interconnecting cavity bellows of 1.3 GHz, continuous wave, cryomodule of the Linac Coherent Light Source-II linear accelerator. Studies are performed for two types of the bellows surfaces i.e. stainless-steel and copper. The results show that RF heating at stainless-steel surface is about four times higher than at copper surface. In this work we also develop a simplified analytical model to analyse the bellows surface temperature growth resulting from RF heating. The model shows a good agreement with numerical analysis and indicates a temperature growth of up to 70 K in stainless-steel bellows in the steady state. Calculations also show that a thin copper coating of 15 μm on stainless-steel surface not only reduces RF heating but also confines the temperature growth well within 10 K. The studies presented here attribute practical importance guiding to characterize copper coating requirements for non-superconducting components in a cryomodule and allowing to model a more relevant cryogenic heat load budget accounting for bellows heating.

RF design optimization for the SHINE 3.9 GHz cavity

The Shanghai high-repetition-rate XFEL and extreme light facility (SHINE) under construction is designed to be one of the most advanced free electron laser (FEL) facilities in the world. The main part of the SHINE facility is an 8 GeV superconducting Linac operating in continuous wave (CW) mode. The Linac consists of seventy-five 1.3 GHz and two 3.9 GHz cryomodules. Based on the design and experience of 3.9 GHz cavities in the European X-ray free electron laser (E-XFEL) and the Linac coherent light source-II (LCLS-II) projects, we optimize the SHINE 3.9 GHz cavity design to adapt it for CW mode operation. In this paper, we present a particular redesign of the end group for the SHINE 3.9 GHz superconducting cavity that includes a redesign of the end cell and beam pipe to shift away the potentially troublesome lowest high-order modes (HOMs), a modification of the main coupler antenna, and a tuning of the HOM notch filter to meet the cavity requirements. RF losses calculations on the HOM coupler antennas show that the overheating on the inner conductor at the operating mode is diminished significantly. Furthermore, we have also studied the HOMs to ensure there are no dangerously trapped modes in the optimized cavity design.

Status of the LCLS-II Cryogenic Distribution System

The LINAC Coherent Light Source II (LCLS-II) located at SLAC National Accelerator Laboratory (SLAC) in Menlo Park, CA, is a U.S. Department of Energy project tasked to design and build a world-class x-ray free-electron laser facility for scientific research. The Linac has superconducting radio frequency cryomodules that are connected to the cryogenic plant by the Cryogenic Distribution System (CDS), which consists of distribution boxes with heat exchangers and reliefs, feed caps, end caps, and surface, vertical, and bypass transfer lines. The CDS components were designed and built to specification by industry. The components have been delivered and their installation at SLAC will be discussed. The as-built relief system design will be presented, showing minimization of relief inlet pressure drops while meeting capacity requirements. The relieving flow pressure drops along the lengths of the CDS to centrally located reliefs at the distribution box were analysed to satisfy Pressure Vessel and Process Piping Code criteria to ensure relief performance. The sub-atmospheric 2 K circuit relieving approach will be discussed, which includes a three-way diverter isolation valve suitable for sub-atmospheric service. The component anchoring load design approach and installation into concrete floor will be discussed. This addresses loading, including seismic loading, along the component’s load path to floor anchoring system.

A Novel $In-Situ$ Radiation Damage Diagnostic System for Undulators

Radiation damage has been a known problem at many synchrotron radiations and free-electron lasers facilities, especially those that use hybrid or pure permanent magnet undulators to produce high brightness light. Field strength loss due to demagnetization makes it necessary to remove the insertion device from the tunnel for inspection and repair, which brings several inconveniences. We aimed to develop an in situ radiation damage detection system for undulators capable of diagnosing relative field changes of 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-4</sup> (100 ppm) or smaller. The system measures the flux change in a flexible printed circuit board coil attached to the undulator magnet array by periodically measuring the integral flux change during the opening and closing of the undulator gap. If the magnet block damage occurs, the signal from the coil will decrease proportionally to the damage. First tests performed on variable gap hybrid undulators for the Linac Coherent Light Source II (LCLS-II) at SLAC National Accelerator Laboratory showed that the system is capable of measuring flux changes with a relative precision of approximately 0.7 × 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-4</sup> over several days. Relative field changes smaller than 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-4</sup> were detected in short-term measurements. The novel system that we propose here opens the possibility of detecting radiation damage in undulators during operation.

Plasma ignition and detection for in-situ cleaning of 1.3 GHz 9-cell cavities

Superconducting radio frequency cavities performance preservation is crucial, from vertical test to accelerator operation. Field emission is still one of the performance limiting factors to overcome, and plasma cleaning has been proven successful by the Spallation Neutron Source (SNS), in cleaning field emitters (hydrocarbon contaminants) and increasing the work function of Nb. The cleaning for Linac Coherent Light Source-II will follow the same plasma composition adopted at SNS, which allows in situ processing of cavities installed in cryomodules. A novel method for plasma ignition has been developed at the Fermi National Accelerator Laboratory: a plasma glow discharge is ignited using high order modes to overcome limitations imposed by the fundamental power coupler. The plasma can be easily ignited and tuned in each of the cavity cells using low radio frequency (RF) power, from 100 W to as low as 2 W depending on the gas and pressure. A method for RF plasma detection has been developed: the plasma location is identified within the cavity without the need of cameras. The presented method can be applied to other multicell cavity designs, even for accelerators where the coupling for the fundamental modes at room temperature is very weak.

Resonant excitation of high order modes in the 3.9 GHz cavity of the Linac Coherent Light Source

Construction of the Linac Coherent Light Source II (LCLS-II) is underway for the world's first hard x-ray free-electron laser. A central part of the LCLS-II project is a 4 GeV superconducting radio frequency electron linac that will operate in the continuous wave (cw) mode. The linac is segmented into four sections named as $L0$, $L1$, $L2$, and $L3$. Two 3.9 GHz cryomodules, each housing of eight third-harmonic cavities similar to the cavities developed for the European X-ray Free Electron Laser (XFEL), will be used in section $L1$ of the linac for linearizing the longitudinal beam profile. In this paper, we present a study of trapped high order modes (HOMs) excited by a cw electron beam in the third-harmonic cavities of the LCLS-II linac. A detailed comparison of the original XFEL design and the LCLS-II design with a modified end group is performed in order to estimate the effect of a reduced beam pipe aperture on the efficiency of HOM damping. Furthermore, we apply a statistical analysis of the eigenmode spectrum for the estimation of the probability of resonant HOM losses and influence of HOMs on beam dynamics.

Industrialization of the nitrogen-doping preparation for SRF cavities for LCLS-II

The Linac Coherent Light Source II (LCLS-II) is a new state-of-the-art coherent X-ray source being constructed at SLAC National Accelerator Laboratory. It employs 280 superconducting radio frequency (SRF) cavities in order operate in continuous wave (CW) mode. To reduce the overall cryogenic cost of such a large accelerator, nitrogen-doping of the SRF cavities is being used. Nitrogen-doping has consistently been shown to increase the efficiency of SRF cavities operating in the 2.0 K regime and at medium fields (15–20 MV/m) in vertical cavity tests and horizontal cryomodule tests. While nitrogen-doping’s efficacy for improvement of cavity performance was demonstrated at three independent labs, Fermilab, Jefferson Lab, and Cornell University, transfer of the technology to industry for LCLS-II production was not without challenges. Here we present results from the beginning of LCLS-II cavity production. We discuss qualification of the cavity vendors and the first cavities from each vendor. Finally, we demonstrate that nitrogen-doping has been successfully transferred to SRF cavity vendors, resulting in consistent production of cavities with better cryogenic efficiency than has ever been achieved for a large-scale accelerator.

Operational experience from LCLS-II cryomodule testing

This paper describes the initial operational experience gained from testing Linac Coherent Light Source II (LCLS-II) cryomodules at Fermilab’s Cryomodule Test Facility (CMTF). Strategies for a controlled slow cooldown to 100 K and a fast cooldown past the niobium superconducting transition temperature of 9.2 K will be described. The test stand for the cryomodules at CMTF is sloped to match gradient in the LCLS-II tunnel at Stanford Linear Accelerator (SLAC) laboratory, which adds an additional challenge to stable liquid level control. Control valve regulation, Superconducting Radio-Frequency (SRF) power compensation, and other methods of stabilizing liquid level and pressure in the cryomodule 2.0 K SRF cavity circuit will be discussed. Several different pumping configurations using cold compressors and warm vacuum pumps have been used on the cryomodule 2.0 K return line and the associated results will be described.

Process simulations for the LCLS-II cryogenic systems

Linac Coherent Light Source II (LCLS-II), a 4 GeV continuous-wave (CW) superconducting electron linear accelerator, is to be constructed in the existing two mile Linac facility at the SLAC National Accelerator Laboratory. The first light from the new facility is scheduled to be in 2020. The LCLS-II Linac consists of thirty-five 1.3 GHz and two 3.9 GHz superconducting cryomodules. The Linac cryomodules require cryogenic cooling for the super-conducting niobium cavities at 2.0 K, low temperature thermal intercept at 5.5-7.5 K, and a thermal shield at 35-55 K. The equivalent 4.5 K refrigeration capacity needed for the Linac operations range from a minimum of 11 kW to a maximum of 24 kW. Two cryogenic plants with 18 kW of equivalent 4.5 K refrigeration capacity will be used for supporting the Linac cryogenic cooling requirements. The cryogenic plants are based on the Jefferson Lab’s CHL-II cryogenic plant design which uses the “Floating Pressure” design to support a wide variation in the cooling load. In this paper, the cryogenic process for the integrated LCLS-II cryogenic system and the process simulation for a 4.5 K cryoplant in combination with a 2 K cold compressor box, and the Linac cryomodules are described.

3D multiphysics modeling of superconducting cavities with a massively parallel simulation suite

Radiofrequency cavities based on superconducting technology are widely used in particle accelerators for various applications. The cavities usually have high quality factors and hence narrow bandwidths, so the field stability is sensitive to detuning from the Lorentz force and external loads, including vibrations and helium pressure variations. If not properly controlled, the detuning can result in a serious performance degradation of a superconducting accelerator, so an understanding of the underlying detuning mechanisms can be very helpful. Recent advances in the simulation suite ace3p have enabled realistic multiphysics characterization of such complex accelerator systems on supercomputers. In this paper, we present the new capabilities in ace3p for large-scale 3D multiphysics modeling of superconducting cavities, in particular, a parallel eigensolver for determining mechanical resonances, a parallel harmonic response solver to calculate the response of a cavity to external vibrations, and a numerical procedure to decompose mechanical loads, such as from the Lorentz force or piezoactuators, into the corresponding mechanical modes. These capabilities have been used to do an extensive rf-mechanical analysis of dressed TESLA-type superconducting cavities. The simulation results and their implications for the operational stability of the Linac Coherent Light Source-II are discussed.

Optical Shaping of X-Ray Free-Electron Lasers.

In this Letter we report the experimental demonstration of a new temporal shaping technique for x-ray free-electron lasers (FELs). This technique is based on the use of a spectrally shaped infrared (IR) laser and allows optical control of the x-ray generation process. By accurately manipulating the spectral amplitude and phase of the IR laser, we can selectively modify the electron bunch longitudinal emittance thus controlling the duration of the resulting x-ray pulse down to the femtosecond time scale. Unlike other methods currently in use, optical shaping is directly applicable to the next generation of high-average power x-ray FELs such as the Linac Coherent Light Source-II or the European X-FEL, and it enables pulse shaping of FELs at the highest repetition rates. Furthermore, this laser-shaping technique paves the way for flexible tailoring of complex multicolor FEL pulse patterns required for nonlinear multidimensional x-ray spectroscopy as well as novel multicolor diffraction imaging schemes.

Impact of nitrogen doping of niobium superconducting cavities on the sensitivity of surface resistance to trapped magnetic flux

Future particle accelerators such as the SLAC “Linac Coherent Light Source-II” (LCLS-II) and the proposed Cornell Energy Recovery Linac require hundreds of superconducting radio-frequency (SRF) niobium cavities operating in continuous wave mode. In order to achieve economic feasibility of projects such as these, the cavities must achieve a very high intrinsic quality factor (Q0) to keep cryogenic losses within feasible limits. To reach these high Q0's in the case of LCLS-II, nitrogen-doping of niobium cavities has been selected as the cavity preparation technique. When dealing with Q0's greater than 1 × 1010, the effects of ambient magnetic field on Q0 become significant. Here, we show that the sensitivity to RF losses from trapped magnetic field in a cavity's walls is strongly dependent on the cavity preparation. Specifically, standard electropolished and 120 °C baked cavities show a sensitivity of residual resistance from trapped magnetic flux of ∼0.6 and ∼0.8 nΩ/mG trapped, respectively, while nitrogen-doped cavities show a higher sensitivity of residual resistance from trapped magnetic flux of ∼1 to 5 nΩ/mG trapped. We show that this difference in sensitivities is directly related to the mean free path of the RF surface layer of the niobium: shorter mean free paths lead to less sensitivity of residual resistance to trapped magnetic flux in the dirty limit (ℓ ≪ ξ0), while longer mean free paths lead to lower sensitivity of residual resistance to trapped magnetic flux in the clean limit (ℓ ≫ ξ0). These experimental results are also shown to have good agreement with recent theoretical predictions for pinned vortex lines oscillating in RF fields.