Exposure Limits Research Articles

Sensory irritation and use of the best available science in setting exposure limits: Issues raised by a scientific panel review of formaldehyde human research studies

As a high production volume chemical with recognized sensory irritation and widespread exposure, the human health risk potential of formaldehyde has been reviewed by many international regulatory agencies and scientific advisory bodies. A scientific panel, the Human Studies Review Board, under the auspices of the EPA's Toxic Substances Control Act (TSCA) program recently reviewed the sensory irritation studies included in the 2022 Draft Integrated Risk Information System (IRIS) Formaldehyde Hazard Assessment in the context of their use in a weight of evidence evaluation of acute inhalation health effects. This panel issued a series of recommendations on the use of these studies for the purposes of calculating exposure limits (e.g., study design preferences; uncertainty adjustment). Considering that these recommendations might reflect topic areas with varying degrees of scientific consensus, this commentary reflects on commonalities and distinctions amongst international formaldehyde exposure limits based on sensory irritation. Notably, each review panel charged with an assessment of the science recommended that no adjustment was needed to account for either exposure duration or human variability. These areas of scientific consensus should be considered as the best available science for the purposes of setting exposure limits in the anticipated TSCA Risk Evaluation on formaldehyde.

Co-exposure of petrochemical workers to noise and mixture of benzene, toluene, ethylbenzene, xylene, and styrene: Impact on mild renal impairment and interaction

Epidemiological evidence concerning effects of simultaneous exposure to noise and benzene, toluene, ethylbenzene, xylene, and styrene (BTEXS) on renal function remains uncertain. In 2020, a cross-sectional study was conducted among 1160 petrochemical workers in southern China to investigate effects of their co-exposure on estimated glomerular filtration rate (eGFR) and mild renal impairment (MRI). Noise levels were assessed using cumulative noise exposure (CNE). Urinary biomarkers for BTEXS were quantified. We found the majority of workers had exposure levels to noise and BTEXS below China's occupational exposure limits. CNE, trans, trans-muconic acid (tt-MA), and the sum of mandelic acid and phenylglyoxylic acid (PGMA) were linearly associated with decreased eGFR and increased MRI risk. We observed U-shaped associations for both N-acetyl-S-phenyl-L-cysteine (SPMA) and o-methylhippuric acid (2-MHA) with MRI. In further assessing the joint effect of BTEXS (β, −0.164 [95% CI, −0.296 to −0.033]) per quartile increase in all BTEXS metabolites on eGFR using quantile g-computation models, we found SPMA, tt-MA, 2-MHA, and PGMA played pivotal roles. Additionally, the risk of MRI associated with tt-MA was more pronounced in workers with lower CNE levels (P = 0.004). Multiplicative interaction analysis revealed antagonisms of CNE and PGMA on MRI risk (P = 0.034). Thus, our findings reveal negative dose-effect associations between noise and BTEXS mixture exposure and renal function in petrochemical workers. With the exception of toluene, benzene, xylene, ethylbenzene, and styrene are all concerning pollutants for renal dysfunction. Effects of benzene, ethylbenzene, and styrene exposure on renal dysfunction were more pronounced in workers with lower CNE.

The study on biological exposure index of occupational exposure to arsenic and its inorganic compounds

Objective: To establish biological exposure index (BEI) of occupational exposure to arsenic and its inorganic compounds through occupational epidemiology and the regression analysis of internal and external exposure of workers. Methods: In November 2021, 125 workers with occupational exposure to arsenic and its inorganic compounds and 49 office administrators in a non-ferrous metal smelter in Yunnan Province were selected as the exposure group and control group, respectively. Air samples from the workplace of the study subjects on weekdays were collected and arsenic concentrations were determined. Urine samples were collected in end-of-work weekend and high performance liquid chromatography-inductively coupled plasma mass spectrometry (HPLC-ICP-MS) was used to detect the levels of trivalent inorganic arsenic (iAs(3+)) , pentavalent inorganic arsenic (iAs(5+)) , monomethyl arsenic (MMA) and dimethyl arsenic (DMA) in urine. The correlations between arsenic concentration in the workplace air and arsenic species in urine of workers were analyzed. Arsenic exposure concentration and the level of urinary arsenic (ΣiAs+MMA+DMA) of workers was analyzed by linear regression and the BEI of arsenic and its inorganic compounds in the workplace was proposed based on the results of micronucleus test. Results: The median of time-weighted average concentration (C(TWA)) of arsenic in the workplace air of the exposure group was 0.0116 mg/m(3), and the over-standard rate was 71.2% (89/125) . The concentrations of iAs(3+), iAs(5+), inorganic arsenic (iAs=ΣiAs(3+)+iAs(5+)) 、MMA、DMA and urinary arsenic in the exposure group were higher than those in the control group at the end of shift, and the differences were statistically significant (P<0.05) . The concentration of arsenic in the workplace air had the strongest correlation with the concentration of urinary arsenic at the end of the shift (r(s)=0.909, P<0.001) . The regression equation was lg (y) =7.662+2.968lg (x) (r=0.821, P<0.05) . According to the occupational exposure limit (OEL) of arsenic in China, the concentration of urinary arsenic in the end-of-work weekend was calculated to be 53.2 μg/L. Combined with the results of micronucleus test, the BEI of occupational exposure to arsenic and its inorganic compounds in the workplace was proposed to be 50 μg/L. Conclusion: The urinary arsenic in the end-of-work weekend can be used as a biomarker of occupational exposure to arsenic, and its BEI is recommended to be 50 μg/L.

Comparison and analysis research on occupational exposure limits of coal dust between China and foreign countries

Objective: To study and compare the occupational exposure limits (OELs) of coal dust between China and foreign countries, understand the OEL of coal dust in China, and provide data and basis for revising the OEL of coal dust in China. Methods: In August 2023, by searching the official websites of limits setting institutions in relevant countries and regions at home and abroad, collecting and sorting out the OELs of coal dust issued by 10 limit setting institutions in 6 countries and the background information of the formulation, and conducting specific analysis on the classification, limit level and formulation principles of coal dust OEL in each country/institution. Results: In China and Japan, the total dust and respirable dust of coal dust OEL were established respectively, while in other countries, only the time-weighted average concentration (TWA) of respirable coal dust exposure was established. The TWA prescribed by China's Notional Health Commission, the United States Occupational Safety and Health Administration (OSHA) , the United States Mining Safety and Health Administration (MSHA) and the Australian Safety Work Bureau when the SiO(2) content was less than 5% were 5, 2.4, 2 and 3 mg/m(3) respectively. China GBZ 2.1-2019 sets the limit of 2.5 mg/m(3) for respirable coal dust with SiO(2) content less than 10%. The TWA set by the American Conference of Government Industrial Hygienists (ACGIH) and the South African Department of Mines and Energy (DME) for anthracite coal were 0.4 and 0.8 mg/m(3), respectively, and bituminous coal or lignite were 0.9 and 1.8 mg/m(3), respectively. The respirable coal dust TWA set by the National Institute for Occupational Safety and Health (NIOSH) in the United States was 1 mg/m(3), and the TWA set by the New Zealand Work Safety Authority was 3 mg/m(3). Conclusion: At present, the OEL of coal dust in China is at a relatively loose level, and it is suggested to further explore the possibility of revising coal dust OEL.

A82 A SURVEY-BASED ASSESSMENT OF RADIATION PROTECTION ATTITUDES AND PRACTICES IN ADVANCED THERAPEUTIC ENDOSCOPY TRAINING CURRICULUMS

Abstract Background Fluoroscopy-assisted endoscopic procedures such as endoscopic retrograde cholangiopancreatography (ERCP) expose patients and physicians to the risks of ionizing radiation, including infertility, cataracts, skin hypersensitivity, hair loss and cancer. Radiation exposure from these procedures can have lasting adverse effects on the health and productivity of gastroenterologists. With attention to “as low as reasonably achievable” (ALARA) principles, recent efforts to minimize radiation use have emphasized the importance of formal radiation protection education, including during advanced therapeutic endoscopy (ATE) training. However, teaching of basic protective measures in radiation safety during ATE training remains often overlooked. Aims We aimed to learn how radiation safety training is delivered in ATE programs across Canada and the US. Identifying the existing training standards and knowledge will help us understand the current gaps in training curriculums and inform future curricular development. Methods Our study was reviewed by the Ottawa Health Science Network Research Ethics Board in September 2023. Surveys were designed and distributed with the REDCap software and sent to ATE trainees (current and recent graduates within the last 3 years) in Canada and Program Directors (PDs) of accredited ATE programs across Canada and the US. Results The survey was completed by 12 trainees and 4 PDs. These are preliminary results and further survey responses are being collected. The majority of trainees (75%) believed it would be very important for their program’s curriculum to include dedicated radiation safety teaching, but most trainees (83.3%) received no such training. Familiarity in optimizing modifiable fluoroscopy parameters to minimize radiation exposure (collimation, gain, magnification, frame rate modification or pulsed fluoroscopy) was variable among trainees (36.4%-81.8%). Seventy-five percent of trainees were unaware of the annual limit for radiation exposure and only 25% believed they were operating within a safe level. Most trainees (90.9%) felt they were given inadequate training to optimally reduce their risk of radiation exposure and 90.9% expressed a desire for further radiation safety training. Despite these findings, only 50% of PDs believed it would be beneficial to offer dedicated radiation safety training as part of their program’s curriculum. Among PDs, 75% did not feel their trainees had the knowledge required to reduce their risk of radiation exposure and all (100%) felt that dedicated training would be useful. Conclusions These findings indicate a need for more robust radiation safety training. Further studies are needed to understand the most effective way to deliver comprehensive radiation safety training to ATE trainees. Funding Agencies None

Acute occupational inhalation injuries-United States, 2011-2022.

Inhalation injuries due to acute occupational exposures to chemicals are preventable. National surveillance of acute inhalation exposures is limited. This study identified the most common acute inhalation exposure-related incidents by industry sector among US workers. To characterize inhalation-related injuries and their exposures during April 2011-March 2022, state and federal records from the Occupational Safety and Health Administration (OSHA) Occupational Safety and Health Information System (OIS) accident database were analyzed. Industry-specific injury, hospitalization, and fatality rates were calculated. The most frequent acute inhalation incidents investigated by OSHA were caused by inorganic gases (52.9%) such as carbon monoxide (CO) or acids, bases, and oxidizing chemical agents (12.9%) such as anhydrous ammonia. The largest number of fatal and nonfatal injuries were reported in the manufacturing (28.6%) and construction (17.2%) sectors. Workers were affected by acute inhalation exposures in most industries. Using this surveillance, employers can recognize frequently-occurring preventable acute inhalation exposures by industry, such as inorganic gases in the manufacturing sector, and implement prevention measures. Training of workers on exposure characteristics and limits, adverse health effects, and use of protective equipment by exposure agent can prevent inhalation injuries.

Electromagnetic Environment Assessment and Safety Research of Electrified High-Speed Railway Carriages

With the advent of modern, high-speed electrified rail systems, there has been increasing concern about electromagnetic safety in rail carriages. The aim of this study was to assess the electromagnetic safety of passengers on trains by utilizing advanced 3D electromagnetic simulation software. A comprehensive model of the electromagnetic environment experienced by passengers on a CR400AF train, specifically under the influence of catenary radiation, was constructed. We analyzed the magnetic field strength, electric field strength, and current density in the brains of 20 passengers in various positions in the train. The findings revealed that among the 20 passengers analyzed, the maximum and minimum magnetic induction intensity recorded in the brain were 8.41 and 0.01 μT, respectively. The maximum and minimum induced electric field intensities were 1110 and 10 μV/m, respectively. Lastly, the maximum and minimum induced current densities were 1200 and 10 μA/m2, respectively. The results show that when people ride on the CR400AF train, the magnetic induction intensity, induced electric field strength, and induced current density in the brain are below the recommended basic limits of exposure to power frequency electromagnetic fields in the guidelines of the International Committee on Non-Ionizing Radiation Protection. The power frequency magnetic field generated by the catenary can be effectively shielded by the aluminum alloy car body. The final result of this study indicates that the electromagnetic exposure from the contact wire at the level 25 kV does not pose a threat to the health of passengers on the CR400AF train.

MOF-Enabled Electrochemical Sensor for Rapid and Robust Sensing of V-Series Nerve Agents at Low Concentrations.

Among nerve agents, V-series nerve agents are some of the most toxic, making low-concentration detection critical for the protection of individuals, populations, and strategic resources. Electrochemical sensors are ideally suited for the real-time and in-field sensing of these agents. While V-series nerve agents are inherently nonelectroactive, they can be hydrolyzed to electroactive products compatible with electrochemical sensing. Zr(IV) MOFs are next-generation nanoporous materials that have been shown to rapidly catalyze the hydrolysis of nerve agents. This work makes use of these nanomaterials to develop, for the first time, an MOF-enabled electrochemical sensor for V-series nerve agents. Our work demonstrates that the VX thiol hydrolysis product can be electrochemically detected at low concentrations using commercially available gold electrodes. We demonstrate that low-concentration thiol oxidation is an irreversible reaction that is dependent on both mass transport and adsorption. Demeton-S-methylsulfon, a VX simulant, is used to demonstrate the full range of sensor operation that includes hydrolysis and electrochemical detection. We demonstrate that MOF-808 rapidly, selectively, and completely hydrolyzes demeton-S-methylsulfon to less-hazardous dimethyl phosphate and 2-ethylsulfonylethanethiol. Low-concentration measurements of 2-ethylsulfonylethanethiol are performed by using electrochemical techniques. This sensor has a limit of detection of 30 nM or 7.87 μg/L for 2-ethylsulfonylethanethiol, which is near the nerve agent exposure limit for water samples established by the United States military. Our work demonstrates the feasibility of rapid, robust electrochemical sensing of V-series nerve agents at low concentrations for in-field applications.

Branched ZnFe2O4 nanorods grown via chemical spray pyrolysis technique for chemiresistive xylene gas sensor

In this work, we used a chemical spray pyrolysis technique to deposit zinc ferrite (ZF) thin films at different substrate temperatures to study xylene (C8H10) gas sensing properties. The focus is on the detection of xylene, a volatile organic compound (VOC) that is harmful to human health. It was found that the concentration of hazardous xylene gas was below the exposure limit. The substrate temperature has a notable impact on the sensor's performance, and ZF exhibits promise for discerning xylene selectively at 200 °C operating temperature. The results indicate that the ZF film deposited at 225 °C (ZF-B) exhibited a significant response (S = 47.4%) to a 50-ppm xylene concentration. Further analysis illustrates that the film substrate temperature deposited at 225 °C can have a unique morphology including thin branched rods, small nanorods with high surface area and roughness. These features contribute to enhanced sensing response by creating more active centers for gas molecule interactions. The stability test over 125 days indicates that the ZF-B film acts effectively as a xylene gas sensor, emphasizing the effectiveness of ZF thin films in detecting xylene in an air environment.

Noise as a physical risk factor in furniture industry machines

This study aimed to determine the risk level of noise, which is an important physical risk, in small and medium-sized furniture industry enterprises. The noise levels of the circular sawing machines, edge banding machines, and mitre cutting machines, which are among the main processing machines of the sector, were measured. The study was carried out in 32 furniture businesses. The possible risks of noise on the operators of the machines in question and other employees were evaluated. Noise level measurements were made with the help of TESTO 815 measuring device. Dunnett’s T3 test was used to detect differences in noise levels for machine operators and other employees. It was determined that the edge banding machine does not pose an occupational health and safety risk in terms of noise risk factors. However, the mitre cutting machine and the circular sawing machine pose a risk for the machine operator in active production by creating noise above the established exposure limit value. The mitre cutting machine carries the same risk for the machine operator when it is in operation but in passive production. The results revealed the need for personal protective equipment for machine operators for mitre cutting and circular sawing machine.

Adverse effects in traditional and alternative toxicity tests

Chemical safety assessment begins with defining the lowest level of chemical that alters one or more measured endpoints. This critical effect level, along with factors to account for uncertainty, is used to derive limits for human exposure. In the absence of data regarding the specific mechanisms or biological pathways affected, non-specific endpoints such as body weight and non-target organ weight changes are used to set critical effect levels. Specific apical endpoints such as impaired reproductive function or altered neurodevelopment have also been used to set chemical safety limits; however, in test guidelines designed for specific apical effect(s), concurrently measured non-specific endpoints may be equally or more sensitive than specific endpoints. This means that rather than predicting a specific toxicological response, animal data are often used to develop protective critical effect levels, without assuming the same change would be observed in humans. This manuscript is intended to encourage a rethinking of how adverse chemical effects are interpreted: non-specific endpoints from in vivo toxicological studies data are often used to derive points of departure for use with safety assessment factors to create recommended exposure levels that are broadly protective but not necessarily target-specific.

ОЦЕНКА РАДИАЦИОННОЙ ОБСТАНОВКИ ПРИ КРАТКОВРЕМЕННЫХ ПОЛЕТАХ НА ЛУНУ

Background: The issue of assessing the features of factors affecting the formation of radiation doses of astronauts while in orbit of the Moon and on its surface remains insufficiently studied, which is important for ensuring the anti-radiation safety of astronauts on lunar missions. Purpose: To analyze the factors influencing the formation of the radiation dose of astronauts at the stage of finding the spacecraft in orbit of the Moon and the lander on its surface. Material and methods: The features of the dose load levels on astronauts at the stages of the Moon’s orbit and on the Moon’s surface are analyzed and generalized, calculation methods are used taking into account the orbit of the spacecraft around the Moon, the anti-radiation properties of the materials of the lander and spacesuit and the time spent in them during a short-term lunar mission. Results: The total radiation doses of astronauts for 14 days, calculated according to dosimetric measurements during the years of low solar activity (2009 and 2018‒2019), are 19.5‒23.2 mSv for astronauts staying in a spacecraft in lunar orbit, and from 22,7 to 24,0 mSv for astronauts on the Lunar surface, depending on the mass thickness of the protection at the maximum permissible 250 mSv for 1 month. An increase in the mass thickness of the anti-radiation protection of the lander in the equivalent of aluminum from 1.5 to 3-5 g/cm2 and the lunar spacesuit in the equivalent of aluminum from 0.2 to 0.5‒1 g/cm2 will reduce the total radiation dose of astronauts no more than 1.3 times during a 14-day stay on the surface of the moon. The results indicate that in order to minimize the radiation doses that astronauts receive during a lunar mission, it is important to take into account the forecast of solar activity in order to optimize the launch time of the spacecraft in the «windows» with minimal levels of radiation exposure. Conclusion: When predicting radiation hazard levels for astronauts during a short-term lunar mission, it is necessary to assess the levels of exposure to cosmic ionizing radiation both in the orbit of the Moon, depending on the lunar trajectory of the spacecraft, and on the surface of the Moon, taking into account the time spent in the lunar module and in a spacesuit, as well as levels of solar activity. It is important to take into account the analyzed features of the formation of cosmonauts’ radiation doses while orbiting the Moon and on its surface when predicting the time limits of the lunar mission, anti-radiation protection of astronauts and their compliance with the regulatory limits of exposure.

Noise Exposure, Prevention, and Control in Agriculture and Forestry: A Scoping Review

Noise is a major physical hazard in agricultural activities, and numerous research activities have managed to detect its effects, resulting in surveys and measurements which help to define exposure limits, prevention methods, and control strategies. This review aims to collect and analyse the data from research studies and to provide a comprehensive overview on the subject. Thus, a set of 81 papers, gathered from the Scopus and PubMed scientific databases, has been analysed to provide information regarding the evolution of noise exposure levels over time, to highlight findings on noise-induced hearing loss (NIHL), and to list strategies for noise prevention and control in agriculture. Bibliographic research showed that noise measurements between 1991 and 2022, included in scientific research on farming, forestry, and animal husbandry, mainly reported values beyond the threshold of 85 dB(A); furthermore, several research activities on NIHL showed that farmers’ family members and children are often exposed to high levels of noise. Lastly, an analysis of the prevention and control strategies over time is provided, focusing on prevention programmes, screening, and the use of hearing protection devices (HPD). The identified literature suggests that additional efforts are required in regards to machinery design relating to the socio-technical aspects of agricultural activities and that side-effects of NIHL, as well as the negative impact of noise on other risks, might deserve further investigation.

Radiation Exposure Characteristics among Healthcare Workers: Before and After Japan's Ordinance Revision.

Radioactive materials and ionizing radiation have both medical value and disease risks, necessitating radiation dose measurement and risk reduction strategies. The International Commission on Radiological Protection (ICRP) lowered the lens of the eye exposure limit, leading to Japan's revised "Ionizing Radiation Ordinance." However, the effects on radiation exposure in medical settings and compliance feasibility remain unclear. To examine the impact of the revision to the "Ionizing Radiation Ordinance" and use it for measures to reduce exposure to radiation, a comprehensive analysis was conducted on data collected from Nagasaki University Hospital, Hiroshima University Hospital, and Fukushima Medical University Hospital in 2018, 2020, and April to September 2021. This included information on age, sex, occupation, department, and monthly radiation doses of workers, aiming to assess the impact of the revision to the "Ionizing Radiation Ordinance" on radiation exposure before and after its enforcement. Out of 9,076 cases studied, 7,963 (87.7%) had radiation doses below the measurable limit throughout the year. Only 292 cases (3.2%) exceeded 1 mSv y -1 , with 9 doctors and 2 radiological technologists surpassing 5 mSv y -1 . Radiological technologists showed significantly higher doses compared to doctors, dentists, and nurses (p < 0.01), while male subjects had significantly higher exposure doses than females (p < 0.01). No significant changes in radiation exposure were observed before and after the revision of the Ionizing Radiation Ordinance; however, variations in radiation exposure control were noted, particularly among nurses and radiological technologists, suggesting the impact of the revision and the need for tailored countermeasures to reduce radiation dose in each group.

Screening of low-toxic zinc oxide nanomaterials and study the apoptosis mechanism of NSC-34 cells.

With the increasing application of ZnO nanomaterials (ZnO-NMts) in the biomedical field, it is crucial to assess their potential risks to humans and the environment. Therefore, this study aimed to screen for ZnO-NMts with low toxicity and establish safe exposure limits, and investigate their mechanisms of action. The study synthesized 0D ZnO nanoparticles (ZnO NPs) and 3D ZnO nanoflowers (ZnO Nfs) with different morphologies using a hydrothermal approach for comparative research. The ZnO-NMts were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Mouse brain neuronal cells (NSC-34) were incubated with ZnO NMts for 6, 12, and 24h, and the cell morphology was observed using TEM. The toxic effects of ZnO Nfs on NSC-34 cells were studied using CCK-8 cell viability detection, reactive oxygen species (ROS) measurement, caspase-3 activity detection, Annexin V-FITC/PI apoptosis assay, and mitochondrial membrane potential (Δφm) measurement. The results of the research showed that ZnO-NMts caused cytoplasmic vacuolization and nuclear pyknosis. After incubating cells with 12.5µgmL-1 ZnO-NMts for 12h, ZnO NRfs exhibited the least toxicity and ROS levels. Additionally, there was a significant increase in caspase-3 activity, depolarization of mitochondrial membrane potential (Δφm), and the highest rate of early apoptosis.This study successfully identified ZnO NRfs with the lowest toxicity and determined the safe exposure limit to be<12.5µgmL-1 (12h). These findings will contribute to the clinical use of ZnO NRfs with low toxicity and provide a foundation for further research on their potential applications in brain disease treatment.

Analysis of respirable dust exposure data collected at a Zambian copper mine between 2017 and 2022.

Mine workers are occupationally exposed to respirable dust, which can cause irreversible lung diseases and controlling exposure concentrations to as low as reasonably practicable is, therefore, essential. To implement exposure reduction strategies and adequately manage exposure to hazardous chemicals, exposure needs to be measured and recorded according to a standard exposure management plan. This study aimed to assess the available respirable dust exposure data measured between 2017 and 2022 in various work areas and job categories at two mining shafts and a concentrator plant of a Zambian copper mine. Additionally, the monitoring program implemented at the mine was assessed for appropriateness. Descriptive data analysis was used to create an exposure matrix comprising 253 exposure measurements. Approximately 5.6% of the measured concentrations exceeded the South African time-weighted average occupational exposure limit (TWA-OEL) of 3 mg/m3. The geometric means of respirable dust exposure for shaft A, shaft B and the concentrator plant were 0.44 mg/m3, 0.44 mg/m3, and 0.68 mg/m3, respectively. The work areas with the highest maximum exposure results were the tipping area (18.0 mg/m3) at shaft A, the sump and waste bin (8.05 mg/m3) at shaft B and the screening (10.8 mg/m3), secondary crusher (14.0 mg/m3), foreign ore bin (4.43 mg/m3), and tertiary crusher (5.07 mg/m3) areas at the concentrator plant. It was found that the monitoring strategy implemented at the mine was flawed and did not collect a sufficient number of samples in each area during each year to make rigorous statistical assessment possible. This study highlights the sampling strategy's shortcomings and recommends adopting a standardized monitoring strategy, such as EN689, to improve the respirable dust monitoring program at the mine. Additionally, this strategy can be implemented across Zambia and, if implemented correctly, it has the potential to be improve exposure monitoring across the country as no standard sampling strategy is currently enforced by the Government.

A critical review of advances in tumor metabolism abnormalities induced by nitrosamine disinfection by-products in drinking water.

Intensified sanitation practices amid the recent severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) outbreak might result in the increased release of chloramine disinfectants into surface water, significantly promoting the formation of nitrosamine disinfection by-products (DBPs) in drinking water. Unfortunately, these nitrosamine DBPs exhibit significant genotoxic, carcinogenic, and mutagenic properties, whereas chlorinating disinfectants remain in global practice. The current review provides valuable insights into the occurrence, identification, contamination status, exposure limits, and toxicity of the new unregulated disinfection by-products (nitrosamine DBPs) in drinking water. As a result, concentrations of nitrosamine DBPs far exceed allowable limits in drinking water, and prolonged exposure has the potential to cause metabolic disorders, a critical step in tumor initiation and progression. Importantly, based on recent research, we have concluded the role of nitrosamines DBPs in different metabolic pathways. Remarkably, nitrosamine DBPs can induce chronic inflammation and initiate tumors by activating sphingolipid and polyunsaturated fatty acid metabolism. Regarding amino acid and nucleotide metabolism, nitrosamine DBPs can inhibit tryptophan metabolism and de novo nucleotide synthesis. Moreover, inhibition of de novo nucleotide synthesis fails to repair DNA damage induced by nitrosamines. Additionally, the accumulation of lactate induced by nitrosamine DBPs may act as a pivotal signaling molecule in communication within the tumor microenvironment. However, with the advancement of tumor metabolomics, understanding the role of nitrosamine DBPs in causing cancer by inducing metabolic abnormalities significantly lags behind, and specific mechanisms of toxic effects are not clearly defined. Urgently, further studies exploring this promising area are needed.

Beurteilung der Lungenfibrose durch extreme und langjährige Einwirkung von Schweißrauchen (Siderofibrose) – Berufskrankheit Nr. 4115

Assessment of pulmonary fibrosis due to extreme and long-term exposure to welding fumes (siderofibrosis) – occupational disease no. 4115. Technical aspects – exposure to welding fumes Pulmonary fibrosis due to welding fumes (siderofibrosis) has occupational disease status in Germany. However, legislation covering the respective occupational disease requires “long-term and extreme exposure” to welding fumes for compensation by the social accident insurance. A recent social court sentence has evoked a discussion on how to further define these criteria. This article is intended to propose a science-based approach to the conditions under which welding fume exposure can be considered „extreme“. For this purpose, the authors discuss occupational exposure limits, circumstances influencing exposure intensity and utilization of welding fume measurement data. Furthermore, the article deals with the way court sentencing will affect suspected cases of siderofibrosis in the future and how the court´s reasoning is compatible with the occupational disease´s scientific report on the one hand and occupational safety regulations on the other hand. In compliance with the sentencing, „welding in confined spaces“ formerly applied as the sole criterion to consider welding conditions „extreme“ is now regarded as obsolete. A definite threshold value used to confirm the existence of „extreme“ conditions can neither be derived from the occupational disease´s scientific report nor from other sources. Given that, the authors propose to focus on welding methods used in specific cases with close regard to a welding procedere´s emission intensity and to occupational hygiene conditions in general when investigating whether conditions were „extreme“ or not. Regarding the mandatory criteria of „long-term exposure“ to welding fumes, only those times should be considered when welding was performed for several hours a day. Short-time exposures however, should not be taken into account. Keywords: welding – fume exposure – occupational disease – siderofibrosis – pulmonary fibrosis

Effects of 90 dB pure tone exposure on auditory and cardio-cerebral system functions in macaque monkeys

Excessive noise exposure presents significant health risks to humans, affecting not just the auditory system but also the cardiovascular and central nervous systems. This study focused on three male macaque monkeys as subjects. 90 dB sound pressure level (SPL) pure tone exposure (frequency: 500Hz, repetition rate: 40Hz, 1 min per day, continuously exposed for 5 days) was administered. Assessments were performed before exposure, during exposure, immediately after exposure, and at 7-, 14-, and 28-days post-exposure, employing auditory brainstem response (ABR) tests, electrocardiograms (ECG), and electroencephalograms (EEG). The study found that the average threshold for the Ⅴ wave in the right ear increased by around 30 dB SPL right after exposure (P < 0.01) compared to pre-exposure. This elevation returned to normal within 7 days. The ECG results indicated that one of the macaque monkeys exhibited an RS-type QRS wave, and inverted T waves from immediately after exposure to 14 days, which normalized at 28 days. The other two monkeys showed no significant changes in their ECG parameters. Changes in EEG parameters demonstrated that main brain regions exhibited significant activation at 40Hz during noise exposure. After noise exposure, the power spectral density (PSD) in main brain regions, particularly those represented by the temporal lobe, exhibited a decreasing trend across all frequency bands, with no clear recovery over time. In summary, exposure to 90 dB SPL noise results in impaired auditory systems, aberrant brain functionality, and abnormal electrocardiographic indicators, albeit with individual variations. It has implications for establishing noise protection standards, although the precise mechanisms require further exploration by integrating pathological and behavioral indicators.

Needle trap devices packed with an imine-based 2D COF: An innovative tool for the sampling of polycyclic aromatic hydrocarbons in air

This study introduces a new method for sampling and microextraction of polycyclic aromatic hydrocarbons (PAHs) in the air using needle trap devices (NTDs) packed with an imine-based covalent-organic framework (COF) as an adsorbent. The NTD was coupled with gas chromatography-flame ionization detection (GC-FID) for analytes’ separation and quantification. The COF adsorbent was synthesized using a solvothermal method at room temperature and packed inside a stainless-steel needle. The adsorbent was characterized using X-ray diffraction analysis (XRD), Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), field-emission scanning electron microscopy (FE-SEM-EDS) and Brunauer-Emmett-Teller (BET) analysis. The method was developed in the laboratory under various conditions and subsequently applied in the field to compare the results with those obtained using sampling and analytical method-NIOSH 5528. The desorption conditions and breakthrough volume (BtV) were optimized at recommended exposure limits concentration using response surface methodology (RSM) with a central composite design (CCD). Accordingly, the optimal values for desorption temperature and BtV were obtained 310 °C and 2840 mL, respectively. The limits of detection (LODs) and the limits of quantification (LOQs) were found to be 0.021–0.027 and 0.065–0.091 μg L−1, respectively. The repeatability and reproducibility of the method (R%) were estimated to be 4.02–6.83 % and 8.51–10.34 %, respectively. Also comparing the mean concentrations of the samples collected by the NTD and the NIOSH 5528 method, revealed no statistically significant differences between the methods (p > 0.05). Overall, the COF-packed NTD was identified as an appropriate and reliable method for sampling and extracting occupational and ambient contaminants in the workplace air.