Limited Energy Resources Research Articles

Technical Analysis Using 100 Percent Palm Kernel Shell as Fuel in Circulation Fluidized Bed Boiler Type

Energy is a basic human need that has increased in use. Given the limited energy resources, it is necessary to manage energy appropriately and efficiently. Energy efficiency not only has an impact on reducing production costs, but also on reducing emissions. As a concrete step to support the government's net zero emission program by 2060, the company is trying to use alternative biomass fuels, namely: palm kernel shell. The purpose of this study is to conduct a technical and economic analysis of the use of 100 percent palm kernel shells as fuel in a circulation fluidized bed boiler type power plant. This research was conducted at power plant unit 2 of PT XYZ, located in Cilegon, Banten Province. The parameters measured are limited to boiler efficiency, thermal efficiency, and heat rate. The results showed that when using palm kernel shells, boiler efficiency decreased 0.47 percent, thermal efficiency decreased 0.24 percent, and heat rate increased 22 kcal/kWh or 0.76 percent. By considering of three operational parameters (boiler efficiency, thermal efficiency, and heat rate) it can be concluded that technically the use of 100 percent palm kernel shells as fuel in the plant is feasible. There is no major impact on boiler performance regarding the transition of coal to palm kernel shells. The impact of long-term use of palm kernel shells on equipment is beyond the scope of this research.

An energy‐efficient method using PSO clustering and fuzzy routing to reduce energy consumption in IoT

SummaryIn “Internet of Things” (IoT) technology, all objects can connect to the Internet with a unique Internet address. The sensors have limited energy resources due to their use of batteries in supplying energy, and since battery replacement in these sensors is not usually feasible, the longevity of wireless sensor networks is limited. Therefore, reducing the energy consumption of the used sensors in IoT networks to increase the network lifetime is one of the crucial challenges and parameters in such networks. These networks are subject to a variety of errors. Errors in wireless communication channels, network dynamics due to the mobility of nodes, and the potential for mistakes in mobile nodes are among the causes of errors in these networks. Despite the above failures, the development of routing algorithms in IoT‐based networks has become a significant challenge for researchers, so it is essential to provide routing algorithms to increase network lifespan and reduce energy consumption. In this study, a two‐dimensional network‐based architecture for the Internet of Things is presented. The proposed algorithm first organizes the nodes into logical cells and selects nodes in each cell as the cluster head. The cluster head is selected based on the binary Particle Swarm Optimization algorithm. Then, each node sends its collected data to the cluster head. The cluster heads first aggregate the received data and then use a fuzzy method to send the data to the base station. The proposed algorithm uses the remaining energy level parameter, cluster density, and location of each cell using fuzzy system capabilities and the particle swarm algorithm to try to route data with less energy consumption and increase network lifespan. The proposed method is simulated in ns2 software, and for a more accurate evaluation, we compare it with LEACH, Ant‐C, PSO, EABC, and SOA‐CH algorithms. We see that the proposed method performs better than other methods in terms of energy consumption and network lifespan.

Hybrid Salp Swarm and Improved Whale Optimization Algorithm‐based clustering scheme for improving network lifespan in wireless sensor networks

SummaryWireless sensor networks (WSNs) represent the collection of restricted energy sensor nodes that are deployed in an area of target for gathering potential environment data for decision‐making with respect to their objective of application. However, the implementation of energy‐effective data gathering strategies in large‐scale WSNs is the most challenging due to the limited energy resources. Clustering‐based data gathering strategies are identified to be quite effective for energy saving that directly attributes to extended network lifetime. Moreover, optimal path amid the cluster head (CH) and sink node needs to be selected for sustaining energy efficiency and improving network lifespan. In this article, Hybrid Salp Swarm and Improved Whale Optimization Algorithm (HSSIWOA)‐based clustering scheme is proposed for improving the network lifetime and routing optimization with maximized energy efficacy. It integrated the exploration capability of Salp Swarm Optimization Algorithm (SSOA) with exploitation benefits of Improved Whale Optimization Algorithm (IWOA) for balancing the trade‐off between the rate of exploration and exploitation during CH selection process. It utilized the parameters of residual energy, load balance, intra‐cluster distance, inter‐cluster distance, and node centrality into account during the process of fitness evaluation. It performed well by constructing an optimized number of clusters, such that energy stability and network lifetime are maintained in the network. The experimental results of the proposed HSSIWOA scheme confirmed extended network lifetime of 21.64%, minimized energy utilization of 23.42%, and maximized throughput of 18.56%, better than the baseline approaches.

Energy demand and carbon emission analyses of a solar-driven domestic regional environment mobile robot as household auxiliary heating and cooling method

Under the trend of energy saving and carbon reduction, reducing household energy consumption, which is an important part of social energy consumption, has become a hot topic. In order to solve the problem of mismatch between supply and demand of household environment control systems as well as to better meet the individual needs of users, we innovatively designed a solar-driven domestic regional environment mobile robot as auxiliary heating and cooling method. In this paper, a simplified thermal network analysis of the thermal conditions of a dwelling is utilized to calculate the energy saving and carbon reduction potential on summer and winter reference days in Beijing and Guangzhou, China. The simulation results show that the system has good energy saving potential and carbon reduction effect. In particular, the single-day energy saving potential of the system on winter days in Beijing reaches to 583.6 kWh compared to the traditional method. Under the power supply mode, the single-day carbon reduction can reach 462 kg CO2 on winter days in Guangzhou, and it can reach 333.2 kg CO2 on summer days in Beijing. We also discuss the effect of regional space size and clothing thermal resistance. As the local space size and the clothing thermal resistance increases, the energy saving potential and carbon reduction benefits of the system decrease, but the overall impact is small. The proposed mobile robot following in the vicinity of home inhabitants to help maintain their thermal comfort, can improve the efficiency of dwellings heating and cooling systems and utilize the limited solar energy resources in family area.

Recent advances in engineering fast-growing cyanobacterial species for enhanced CO2 fixation

Atmospheric CO2 removal (CDR) is a fundamentally endergonic process. Performing CDR or Bioenergy with Carbon Capture and Storage (BECCS) at the gigatonne scale will produce a significant additional burden on the planet’s limited renewable energy resources irrespective of the technology employed. Harnessing photosynthesis to drive industrial-scale CO2 fixation has been of significant interest because of its minimal energy requirements and potential low costs. In this review, we evaluated the thermodynamic considerations of performing atmospheric carbon removal using microalgae and cyanobacteria versus physicochemical processes and explore the implications of these energetic costs on the scalability of each respective solution. We review the biomass productivities of recently discovered fast-growing cyanobacterial strains and discuss the prospects of genetically engineering certain metabolic pathways for channeling the fixed carbon into metabolic ‘carbon sinks’ to further enhance their CO2 capture while concurrently extracting value. We share our perspectives on how new highly productive chassis strains combined with advanced flux balance models, essentially coupling synthetic biology with industrial biotechnology, may unlock more favorable methods for CDR, both from an economic and thermodynamic perspective.

Quantized non-volatile nanomagnetic domain wall synapse based autoencoder for efficient unsupervised network anomaly detection

Anomaly detection in real-time using autoencoders implemented on edge devices is exceedingly challenging due to limited hardware, energy, and computational resources. We show that these limitations can be addressed by designing an autoencoder with low-resolution non-volatile memory-based synapses and employing an effective quantized neural network learning algorithm. We further propose nanoscale ferromagnetic racetracks with engineered notches hosting magnetic domain walls (DW) as exemplary non-volatile memory-based autoencoder synapses, where limited state (5-state) synaptic weights are manipulated by spin orbit torque (SOT) current pulses to write different magnetoresistance states. The performance of anomaly detection of the proposed autoencoder model is evaluated on the NSL-KDD dataset. Limited resolution and DW device stochasticity aware training of the autoencoder is performed, which yields comparable anomaly detection performance to the autoencoder having floating-point precision weights. While the limited number of quantized states and the inherent stochastic nature of DW synaptic weights in nanoscale devices are typically known to negatively impact the performance, our hardware-aware training algorithm is shown to leverage these imperfect device characteristics to generate an improvement in anomaly detection accuracy (90.98%) compared to accuracy obtained with floating-point synaptic weights that are extremely memory intensive. Furthermore, our DW-based approach demonstrates a remarkable reduction of at least three orders of magnitude in weight updates during training compared to the floating-point approach, implying significant reduction in operation energy for our method. This work could stimulate the development of extremely energy efficient non-volatile multi-state synapse-based processors that can perform real-time training and inference on the edge with unsupervised data.

Effective Hybrid Deep Learning Model of GAN and LSTM for Clustering and Data Aggregation in Wireless Sensor Networks

Background: Wireless Sensor Networks (WSNs) have emerged as a crucial technology for various applications, but they face a lot of challenges relevant to limited energy resources, delayed communications, and complex data aggregation. To address these issues, this study proposes novel approaches called GAN-based Clustering and LSTM-based Data Aggregation (GCLD) that aim to enhance the performance of WSNs. Methods: The proposed GCLD method enhances the Quality of Service (QoS) of WSN by leveraging the capabilities of Generative Adversarial Networks (GANs) and the Long Short-Term Memory (LSTM) method. GANs are employed for clustering, where the generator assigns cluster assignments or centroids, and the discriminator distinguishes between real and generated cluster assignments. This adversarial learning process refines the clustering results. Subsequently, LSTM networks are used for data aggregation, capturing temporal dependencies and enabling accurate predictions. Results: The evaluation results demonstrate the superior performance of GCLD in terms of delay, PDR, energy consumption, and accuracy than the existing methods. Conclusion: Overall, the significance of GCLD in advancing WSNs highlights its potential impact on various applications.

Optimal Deployment of Wireless Sensor Nodes using Particle Swarm Optimization (PSO), Ant Colony Optimization (ACO)

Abstract: Wireless Sensor Networks (WSNs) are emerging as a significant area of research due to their potential to autonomously monitor physical and environmental conditions. These networks comprise spatially distributed, low-cost sensor nodes with limited transmission range, processing capabilities, storage, and energy resources. The primary function of these networks is to collect data from various nodes and transmit it to a base station for subsequent processing. WSNs present several challenges, including optimal sensor deployment, node localization, base station placement, target node location, energy-aware clustering, and data aggregation. Recently, global researchers have been employing a bio-inspired optimization algorithm, Particle Swarm Optimization (PSO), to enhance the efficiency of WSNs. This report explores the application of the PSO algorithm for optimal sensor deployment in WSNs, contributing to the ongoing efforts to maximize the potential of these networks.

A risk-aware and recommender distributed intrusion detection system for home robots

The increasing adoption of home robots, driven by technological advancements and realistic goals, underscores the critical importance of ensuring their security, safety, and privacy. An Intrusion Detection System (IDS) is vital in safeguarding home robots by identifying and responding to potential security threats. However, home robot controllers’ limited computational and energy resources pose challenges. To enhance a home robot’s performance, especially its IDS, one potential solution is to connect it to a home network with a more robust computing infrastructure. Our proposed IDS comprises two components: one resides on a remote PC equipped with substantial computing power, and the other operates directly within the robot controller. By leveraging the remote PC, we achieve enhanced intrusion detection performance and gain valuable recommendations for fine-tuning the intrusion detection component situated in the controller. Simultaneously, it becomes imperative to swiftly identify security threats and prioritize high-risk attacks within the robot controller In this study, we employed machine learning techniques within the IDS. The dataset was generated by simulating robot actions within a home network. Based on our evaluation results, adopting a deep learning model for detecting intrusions in a remote PC and with its recommendations for fine-tuning the intrusion detector in the controller would significantly enhance intrusion detection performance. Additionally, leveraging ensemble learning to identify intrusions in the robot controller component while carefully considering potential risks promises satisfactory outcomes in terms of intrusion detection.

A novel energy-efficient dynamic programming routing protocol in wireless multimedia sensor networks

Wireless multimedia sensor networks (WMSNs) have characteristics that may influence the routing decisions, such as limited energy resources, storage and computing capacity. Therefore, a routing optimization needs to be done to match the characteristics of the WMSNs. Existing routing protocols only consider energy efficiency regardless of energy threshold, maximum energy, and link cost collectively as the primary basis of routing. In this work, the energy-efficient dynamic programming (EEDP) protocol is proposed to optimize routing decisions that take into account the energy threshold, the maximum energy, and the link cost. Then, the protocol is compared with the dynamic programming (DP), and the ant colony optimization (ACO) protocol. The simulation results show that the EEDP protocol can improve energy efficiency of nodes and network lifetime of the WMSNs. Then, the EEDP protocol is also implemented into a network topology of 10 NodeMCU ESP32 devices. As a result, the EEDP protocol can work very well by selecting routes based on nodes that have the remaining energy above 50 and has the shortest distance. The average delay in sending data for the entire route for the 10 iterations of sending data is 3.99 seconds.

ISSUES OF CREATING A SYSTEM FOR EARLY DETECTION OF FOREST FIRES BASED ON UNMANNED AERIAL VEHICLES

The urgent importance of the task of monitoring the state of forests lies in the danger of forest fires. Forest fires are a frequent occurrence in almost all continents. Despite the high information content of the spectral signs of a forest fire, the corresponding functionality is not fully used in the known implementations of the forest fire early detection system. The spectral region in which it is possible to distinguish forest areas in a state of fire from their usual state is quite wide and covers the middle and thermal zone of the infrared part of the spectrum. The installation of spectral equipment (multi- and hyperspectrometers) on board the UAV (unmanned aerial vehicle) can certainly expand the functionality of unmanned equipment in the early detection of forest fires. The optimal procedure for using UAVs equipped with hyperspectral equipment for early detection of forest fires is proposed. An optimization problem has been formulated and solved to determine the most appropriate mode of changing the UAV flight altitude with an increase in the wavelength of the measurements being carried out. According to the proposed method, on the right branch of the Planck curve, with increasing wavelength, the flight altitude should be increased, and on the left branch it should be reduced. This order corresponds to the case of increasing the wavelength on both branches and follows from the integral restriction set on the function of the dependence of the flight altitude on the wavelength, which comes from the limited real energy resources on board the UAV. Based on the developed method, a new technique for early detection of forest fires based on the use of hyperspectral method is proposed.

Task Offloading Strategy for Unmanned Aerial Vehicle Power Inspection Based on Deep Reinforcement Learning.

With the ongoing advancement of electric power Internet of Things (IoT), traditional power inspection methods face challenges such as low efficiency and high risk. Unmanned aerial vehicles (UAVs) have emerged as a more efficient solution for inspecting power facilities due to their high maneuverability, excellent line-of-sight communication capabilities, and strong adaptability. However, UAVs typically grapple with limited computational power and energy resources, which constrain their effectiveness in handling computationally intensive and latency-sensitive inspection tasks. In response to this issue, we propose a UAV task offloading strategy based on deep reinforcement learning (DRL), which is designed for power inspection scenarios consisting of mobile edge computing (MEC) servers and multiple UAVs. Firstly, we propose an innovative UAV-Edge server collaborative computing architecture to fully exploit the mobility of UAVs and the high-performance computing capabilities of MEC servers. Secondly, we established a computational model concerning energy consumption and task processing latency in the UAV power inspection system, enhancing our understanding of the trade-offs involved in UAV offloading strategies. Finally, we formalize the task offloading problem as a multi-objective optimization issue and simultaneously model it as a Markov Decision Process (MDP). Subsequently, we proposed a task offloading algorithm based on a Deep Deterministic Policy Gradient (OTDDPG) to obtain the optimal task offloading strategy for UAVs. The simulation results demonstrated that this approach outperforms baseline methods with significant improvements in task processing latency and energy consumption.

Decentralized utilization of distributed energy storage resources for simultaneous frequency regulation in a microgrid

A microgrid has emerged for the transformation from centralized into localized electricity generation, which increases the opportunity for renewable-based distributed generators (DGs) applications such as photovoltaic (PV) and wind as well as small-scale conventional generation units. PV and wind integration provides environmental, technical, and economic benefits. However, the low inertia of the PV system and decoupling due to the presence of the power electronics converter in the wind generation system led to a significant declination in the microgrid's inertia, which causes an excessive frequency nadir and a high rate of change of frequency (ROCOF) in the presence of disturbances. The microgrid's inertia can be enhanced by storing or releasing energy within the microgrid. The wind generation system has intrinsic kinetic energy stored in the rotating parts, while the PV system's sorted energy is improved by introducing an external supercapacitor on the DC link. The aforementioned energy storage elements provide limited energy resources, which should be employed in a proper manner. This article proposes a control scheme to boost the cooperation of wind and PV generation systems for the enhancement of inertia and frequency support. Therefore, the proposed scheme prevents excessive stress on individual generators and improves the utilization of available energy resources. For example, at load increase by 0.5 MW, with frequency support using PV only or wind only, the frequency deviation is enhanced by 44.4 % and 29.5 %, respectively. While for both PV and wind support the frequency simultaneously, the frequency deviation is enhanced by 53.3 %. In addition, with the cooperation of PV and wind, the required energy from PV and wind is reduced by 29.5 % and 13.7 % respectively and the rate of change of frequency is enhanced by 61.9 %. The energy share among PV and wind generation systems is investigated and verified by simulations; tuning formulas are also developed to attain predefined energy support with equal energy sharing among different resources. For instance, with a non-equal energy share strategy and load increases by 0.5 MW, the wind delivers almost 1.6 times the energy delivered from the PV. Hence, more stress occurs on the wind generation compared to PV. While, using equal energy share strategy, the required energy from wind is about 1.03 times the energy delivered from the PV. The proposed control scheme is applied to an AC microgrid that comprises a thermal generation plant, a PV generation system, and a doubly-feed induction generator-based wind generation system. To verify the effectiveness of the proposed scheme, different simulation cases considering load change, wind speed variation, irradiance variations, and weak grid integration are implemented. When compared to individual frequency support, the proposed scheme provides a superior response.

Sequential MCDM methods for site selection of hydroponic geothermal greenhouse: ENTROPY and ARAS

With the increasing global population, there is a growing need for agricultural land and an associated impact on greenhouse activities. In response to issues of limited energy and natural resources, the use of hydroponic greenhouses that use renewable energy sources has become increasingly popular. Among these, the use of geothermal energy in hydroponic greenhouses has garnered particular attention. In this study, we propose a sequential solution method that incorporates the Entropy and ARAS methods for the location selection of hydroponic greenhouses heated by geothermal energy. The model considers 5 main criteria, and 21 sub-criteria, and evaluates five alternative cities in Turkey. The weighting of the criteria was established through the Entropy technique. Subsequently, the decision alternatives were ranked using the ARAS method. The results of the study revealed that Denizli province is the most appropriate location for the establishment of a hydroponic geothermal greenhouse in Turkey. The alternative cities of Aydin and Afyonkarahisar were found to be the second and third most suitable provinces respectively. This determination was made based on a thorough evaluation of various factors such as geothermal resources, land availability, and infrastructure. The results of the study align with Turkey's potential for using geothermal energy and its existing greenhouse areas. This study highlights the potential for using geothermal energy in the cultivation of crops in Turkey and suggests that the establishment of hydroponic geothermal greenhouses in these provinces can be a viable and sustainable solution for increasing food production. The proposed sequential solution method may serve as a valuable tool for guiding investment decisions related to geothermal greenhouse applications in other countries.

Reservoir Computing Using Measurement-Controlled Quantum Dynamics

Physical reservoir computing (RC) is a machine learning algorithm that employs the dynamics of a physical system to forecast highly nonlinear and chaotic phenomena. In this paper, we introduce a quantum RC system that employs the dynamics of a probed atom in a cavity. The atom experiences coherent driving at a particular rate, leading to a measurement-controlled quantum evolution. The proposed quantum reservoir can make fast and reliable forecasts using a small number of artificial neurons compared with the traditional RC algorithm. We theoretically validate the operation of the reservoir, demonstrating its potential to be used in error-tolerant applications, where approximate computing approaches may be used to make feasible forecasts in conditions of limited computational and energy resources.

Security Enhancement for Deep Reinforcement Learning-Based Strategy in Energy-Efficient Wireless Sensor Networks.

Energy efficiency and security issues are the main concerns in wireless sensor networks (WSNs) because of limited energy resources and the broadcast nature of wireless communication. Therefore, how to improve the energy efficiency of WSNs while enhancing security performance has attracted widespread attention. In order to solve this problem, this paper proposes a new deep reinforcement learning (DRL)-based strategy, i.e., DeepNR strategy, to enhance the energy efficiency and security performance of WSN. Specifically, the proposed DeepNR strategy approximates the Q-value by designing a deep neural network (DNN) to adaptively learn the state information. It also designs DRL-based multi-level decision-making to learn and optimize the data transmission paths in real time, which eventually achieves accurate prediction and decision-making of the network. To further enhance security performance, the DeepNR strategy includes a defense mechanism that responds to detected attacks in real time to ensure the normal operation of the network. In addition, DeepNR adaptively adjusts its strategy to cope with changing network environments and attack patterns through deep learning models. Experimental results show that the proposed DeepNR outperforms the conventional methods, demonstrating a remarkable 30% improvement in network lifespan, a 25% increase in network data throughput, and a 20% enhancement in security measures.

In-sensor human gait analysis with machine learning in a wearable microfabricated accelerometer

In-sensor computing could become a fundamentally new approach to the deployment of machine learning in small devices that must operate securely with limited energy resources, such as wearable medical devices and devices for the Internet of Things. Progress in this field has been slowed by the difficulty to find appropriate computing devices that operate using physical degrees of freedom that can be coupled directly to degrees of freedom that perform sensing. Here we leverage reservoir computing as a natural framework to do machine learning with the degrees of freedom of a physical system, to show that a micro-electromechanical system can implement computing and the sensing of accelerations by coupling the displacement of suspended microstructures. We present a complete wearable system that can be attached to the foot to identify the gait patterns of human subjects in real-time. The computing efficiency and the power consumption of this in-sensor computing system is then compared to a conventional system with a separate sensor and digital computer. For similar computing capabilities, a much better power efficiency can be expected for the highly-integrated in-sensor computing devices, thus providing a path for the ubiquitous deployment of machine learning in edge computing devices.

Holistic Energy Awareness and Robustness for Intelligent Drones

Drones represent a significant technological shift at the convergence of on-demand cyber-physical systems and edge intelligence. However, realizing their full potential necessitates managing the limited energy resources carefully. Prior work looks at factors such as battery characteristics, intelligent edge sensing considerations, planning, and robustness in isolation. But a global view of energy awareness that considers these factors and looks at various tradeoffs is essential. To this end, we present results from our detailed empirical study of battery charge-discharge characteristics and the impact of altitude and lighting on edge inference accuracy. Our energy models, derived from these observations, predict energy usage while performing various manoeuvres with an error of 5.6%, a 2.5X improvement over the state-of-the-art. Furthermore, we propose a holistic energy-aware multi-drone scheduling system that decreases the energy consumed by 21.14% and the mission times by 46.91% over state-of-the-art baselines. To achieve system robustness in the event of link or drone failure, we observe trends in Packet Delivery Ratio to propose a methodology to establish reliable communication between nodes. We release an open-source implementation of our system. Finally, we tie all of these pieces together using a people-counting case study.

IoT energy efficiency routing protocol using FHO‐based clustering and improved CSO model‐based routing in MANET

SummaryMany protocols, services, and electrical devices with built‐in sensors have been developed in response to the rapid expansion of the Internet of Things. Mobile ad hoc networks (MANETs) consist of a collection of autonomous mobile nodes that can form an ad hoc network in the absence of any pre‐existing infrastructure. System performance may suffer due to the changeable topology of MANETs. Since most mobile hosts operate on limited battery power, energy consumption poses the biggest challenge for MANETs. Both network lifetime and throughput improve when energy usage is reduced. However, existing approaches perform poorly in terms of energy efficiency. Scalability becomes a significant issue in large‐scale networks as they grow, leading to overhead associated with routing updates and maintenance that can become unmanageable. This article employs a MANET routing protocol combined with an energy conservation strategy. The clustering hierarchy is used in MANETs to maximize the network's lifespan, considering its limited energy resources. In the MANET communication process, the cluster head (CH) is selected using Fire Hawk Optimization (FHO). When choosing nodes to act as a cluster for an extended period, CH election factors in connectivity, mobility, and remaining energy. This process is achieved using an optimized version of the Ad hoc On‐Demand Distance Vector (AODV) routing protocol, utilizing Improved Chicken Swarm Optimization (ICSO). In comparison to existing protocols and optimization techniques, the proposed method offers an extended network lifespan ranging from 90 to 160 h and reduced energy consumption of 80 to 110 J, as indicated by the implementation results.

OEE-WCRD: Optimizing Energy Efficiency in Wireless Sensor Networks through Cluster Head Selection Using Residual Energy and Distance Metrics

Wireless Sensor Networks (WSNs) play a pivotal role in various applications, including environmental monitoring, industrial automation, and healthcare. However, the limited energy resources of sensor nodes pose a significant challenge to the longevity and performance of WSNs. To address this challenge, this paper presents an Optimized Energy Efficient Protocol in Wireless Sensor Networks through Cluster Head Selection Using Residual Energy and Distance Metrics (OEE-WCRD). This research paper presents a novel approach to cluster head selection in WSNs by harnessing a combination of residual energy and distance metrics. The proposed method aims to significantly enhance the energy efficiency of WSNs by prioritizing nodes with ample residual energy and proximity to their neighbors as cluster heads. Through extensive simulations and evaluations, we demonstrate the effectiveness of this approach in prolonging network lifetime, optimizing data aggregation, and ultimately advancing the energy efficiency of WSNs, making it a valuable contribution to the field of WSNs protocols.