Limited Value Research Articles

Assessment of whole-body vibration and development of mitigation intervention for single-axle tractor–trailer combination

IntroductionTractarization is synonymous with farm mechanization in India. Tractor-trailers are extensively used for the transportation of farm inputs and produce on and off-road, exposing drivers to excessive vibration.ObjectivesThe study was undertaken to assess tractor drivers’ vibration exposure while using trailers and to develop low-cost mitigation interventions.MethodologyThe whole-body vibrations were measured at the tractor seat during the transportation with a no, half (3715 kg soil) and full payload (5910 kg soil) trailer on two terrain conditions, namely, asphalt and farm terrains. The speeds recommended by ISO 5008-1979 of 10, 12 and 14 km/h on asphalt roads and 4, 5 and 7 km/h on farm roads, as well as actual working speeds preferred by the operator (18, 20 and 22 km/h on asphalt road and 8, 10 and 12 km/h on farm terrain), were selected for experiments. Two vibration reduction interventions, namely spring suspended single point hitch (I1) and polyurethane (PU) bush (I2), were developed and installed between the tractor and trailer. Whole-body vibration (WBV) was measured by repeating the experiments.ResultsThe maximum vibration reduction on asphalt road at 22 km/h with I1 was found as 14.3, 19.03 and 23.1%, whereas on-farm terrain at 12 km/h was found as 15.16, 22.43, and 25.56% for no, half and full payload. Similarly, with I1 + I2 interventions, the maximum total vibration reduction at 22 km/h was 16.86, 21.12 and 25.51% on asphalt roads, whereas on-farm tertian at 12 km/h was 17.07, 23.77 and 28.67%. The average value of lower health guidance caution zone (HGCZ) limits on asphalt roads increased by 1.11, 0.95 and 0.92 h and on-farm tertian 1.55, 1.14 and 0.83 h with no, half, and full payload. The average value of upper HGCZ limits on asphalt roads increased by 3.13, 3.21 and 3.68 h and on-farm tertian by 2.24, 2.94 and 3.31 h with intervention.ConclusionsThis infers that with developed interventions an operator can safely perform for a longer duration and at higher operational speeds because of the reduced vibration.

Experimental values for Nickel and Palladium in gas state resistivity limits

Metals in various phases, including the gas state, can be obtained using a pulsed wire explosive system. If experimental system is properly configured, sufficient metal gas can be obtained to estimate the limits of its electrical resistivity in later phases of the discharge, complementing solid and liquid state measurements of the same parameter. This article presents for the first time those experimental limits for the metals Palladium and Nickel. Obtained values for Palladium maximum limits are in the range from 0.25 to 1.25 10−3 Ω · m, meanwhile Nickel obtained maximum ranges go from 0.3 to 1.5 10−3 Ω · m.

Associations of polygenic risk scores with risks of stroke and its subtypes in Chinese

Background and purposePrevious studies, mostly focusing on the European population, have reported polygenic risk scores (PRSs) might achieve risk stratification of stroke. We aimed to examine the association strengths of...

GBT-CHAIN: A System Framework for Solving the General Trilemma in Permissioned Blockchains

As a subset of distributed systems, blockchain technology is equally bound by the CAP trilemma. Specifically, no distributed system can satisfy consistency, availability, and partition tolerance simultaneously. Informally, the innovative blockchain trilemma has been theorized to include security, scalability, and decentralization. While many software approaches on blockchains claim to solve the trilemma problem, almost all known approaches have been proven to involve tradeoffs and fail to reach the upper bounds, meaning they do not achieve the theoretical limit value in each term of a trilemma. In this article, we propose a general trilemma based on the above two trilemmas. For permissioned blockchains, we then describe a system framework called GBT-CHAIN to solve the G eneral B lockchain T rilemma. In the proposed framework, the consensus and data layer, the network layer, and the physical layer work in cooperation. According to our theoretical proof and experimental analysis, the three properties of the trilemma consisting of consistency, scalability, and partition tolerance are perfectly satisfied without tradeoffs. Our results demonstrate that the general blockchain trilemma is resolved by combining consensus algorithms and physical topologies, in particular for permissioned blockchains.

Source apportionment, ecological and health risk assessment of potentially toxic elements in water, sediment and blackchin tilapia {Sarotherodon melanotheron (Rüppell 1852)} from Lagos and Ologe Lagoons, Lagos State, Nigeria

BackgroundLagos and Ologe Lagoons are parts of the Lagos Lagoon Complex, which provide fish as an animal protein source to the locals. However, these fish species have a high propensity to accumulate pollutants including Potentially Toxic Elements (PTEs) from their environment. This potentially constitutes a health risk to fish consumers. Therefore, this study investigated concentrations of some PTEs (As, Cd, Cr, Cu, Fe, Pb, Ni, and Zn) in water, sediment, and fish (Sarotherodon melanotheron) from Lagos and Ologe Lagoons, the ecological and health risks associated with the consumption of the fish as well as the likely sources of the PTEs. MethodsWater, sediment, and fish (S. melanotheron) samples were collected monthly for ten months (June 2022 - March 2023) from three sites: Badore and Baiyeku in Lagos Lagoon and Ologe Lagoon. The concentration of PTEs was determined in the environmental matrices {water, sediment, and three organs (gill, muscle, liver)}. The range of values for method detection limits (MDL), limits of detection (LOD), limits of quantitation (LOQ), and recovery rates were 0.01 – 0.025 mg kg−1, 0.00002 – 0.002 mg L−1, 0.0001 – 0.0067 mg L−1 and 97.19±2.45 - 99.85±1.16% respectively. The ecological risk of PTE in water and sediment was assessed by various indices. Estimated dietary intake (EDI), health risk index (HRI), and target hazard quotient (THQ) were the human health risk assessment indices employed. The distribution and source of the PTEs were analyzed using the coefficient of variation, Pearson's correlation matrix, principal components analysis, and hierarchical cluster analysis. ResultsThe water and sediment quality assessment indices indicated that the water and sediment from the lagoons had low contamination with respect to the eight PTEs studied. EDI values were generally less than 1 except for Fe and Zn. THQ for all PTEs in the three sampling stations and across the different population groups was less than 1 except for Fe. PCA revealed two major sources of PTE pollution which are natural and anthropogenic. As, Cd, Cr, Cu, and Pb were probably due to anthropogenic inputs like agricultural operations and industrial activities while Fe, Ni, and Zn may have occurred due to lithological sources like rock weathering and volcanic events. ConclusionBased on the result of the study, the waters from the lagoons are still suitable for agricultural usage. The sediments are also largely uncontaminated with respect to the eight PTEs studied. The EDI and THQ show that consumption of S. melanotheron from the sites may not constitute any significant health risk to humans and the sources of the PTEs are lithologic and anthropogenic.

Efficiency and mass optimization for space nuclear power systems with closed Brayton cycle loops

Space nuclear power systems should be strictly limited in mass and size. Lack of detailed designs, mass estimation in the general design phase usually relies on simple and empirical models that leave too much design margin from the limits. Accurate mass estimation of space nuclear power systems is key to minimize the design margin and maximize the system performance in the general design phase. In this paper, new mass estimation models are proposed for the main components of space nuclear power systems, including nuclear reactor, shield, turbine, compressor, heat exchanger, and thermal radiator. The mass estimation models are more accurate by incorporating principles of nuclear physics, thermal hydraulics, and structural mechanics to the component designs. Combined with thermodynamic models and genetic algorithm, the MEGREZ code is developed to optimize the system performance by setting efficiency and mass as dual objectives. The code verification results indicate that the deviations between and the Jupiter Icy Moons Orbiter project parameters and the code calculated values are only 0.4% for system efficiency and 2.1% for system mass. The optimization for the Jupiter Icy Moons Orbiter project shows that the optimal molecular weight of helium-xenon mixture is the minimum value for single-stage turbomachinery limits. Additionally, the impacts of potential technological degradation, such as increased heat exchanger thermal resistances, higher frictional factors, and decreased turbomachinery efficiency, on system performances are discussed. The results show that turbomachinery efficiency presents the strongest influence on the system-specific mass; a 0.04 reduction in the polytropic efficiency of the compressor or turbine results in more than a 10% increase in system-specific mass.

Nondestructive Measurement Technique for Substandard Amoxicillin Based on Thermal Approach.

In this study, we introduce a new nondestructive measurement technique based on a thermal approach for the determination of substandard amoxicillin. The quality control of amoxicillin is critical for patient safety, and one of the essential parameters for its evaluation is the content of the active ingredient. Traditional methods for assessing amoxicillin content are defined by their time-consuming nature, reliance on skilled personnel, and frequent necessity for specific reagents. The proposed device aims to provide a rapid and low-cost alternative that can accurately measure the amoxicillin content without damaging the sample. The method validation results indicate coefficient of determination (R2) exceeding 0.99, with percent recoveries falling within the range of 98.70-103.40%. The calculated values for limit of detection and limit of quantitation were determined to be 28.11 and 85.17 mg/L, respectively. Our experiments employed amoxicillin samples with predetermined concentrations, all of which were below the standard quality. It was observed that the proposed analytical device effectively quantifies the amoxicillin content in aqueous solutions. Each measurement took no more than 10 min, underscoring the efficiency of the analysis process. The experiments were validated through independent testing at the Government Pharmaceutical Organization in Thailand and the department of engineering science in Oxford, which provides strong evidence for the effectiveness and robustness of the technique. Overall, this study demonstrates the feasibility of using a thermal approach for the nondestructive measurement of substandard amoxicillin.

C-reactive protein concentration has limited value in the diagnosis of meningoencephalitis of unknown origin in dogs.

To evaluate blood and cerebrospinal fluid (CSF) concentrations of C-reactive protein (CRP) in dogs with meningoencephalitis of unknown origin (MUO); to evaluate whether blood CRP concentration is associated with epidemiological, clinicopathologic, and MRI findings; and to investigate blood CRP predictive power in survival. 30 client-owned dogs with MUO, 15 client-owned dogs with steroid-responsive meningitis arteritis (SRMA; positive control group), and 15 healthy dogs (negative control group). Blood CRP concentration was measured in each group, while it was performed in CSF only in the MUO and SRMA groups. The analysis of epidemiological data included breed, age, sex, duration of clinical signs, and history of seizures. Blinded analysis of MRI was performed based on a classification grid, and traditional CSF analysis parameters were assessed. The predictive power of blood CRP concentration regarding survival at 6 months was investigated. Of the 30 dogs with MUO, 9 (30%) had an increased CRP concentration in blood, and 3 (10%) showed a measurable CRP in CSF. Median blood CRP concentration in dogs with MUO was 0.1 mg/L (range, 0.1 to 102 mg/L), which was not statistically different from the healthy dog group but significantly lower than the SRMA control group. Only the duration of clinical signs was positively associated with an increased blood CRP level. Blood CRP concentration was not associated with survival at 6 months. Blood CRP concentration is of limited value for the diagnosis and prognosis of dogs with MUO. Chronicity of the disease may be associated with an increased concentration of blood CRP.

Оптимизация параметров импульсной лазерной наплавки стали 30ХГСН2А с использованием генетического алгоритма

The paperpresents the optimization of pulsed laser cladding of structural steel using a genetic algo-rithm. Using the ANSYS Workbench software, finite element modelling of laser cladding on a 30ХГСН2А steel substrate with an additive in the form of wire was conducted, considering the temperature dependence of the material's thermophysical properties. A surrogate model for pulsed laser cladding of 30ХГСН2Аsteel was developed employing a face-centered version of the central composite design experiment. The time inter-vals corresponding to the end time of the three fronts of the laser pulse and the diameter of the filler wire were considered as variable factors. The maximum temperatures in the treatment zone were used as re-sponses. In order to optimize pulsed laser cladding of 30ХГСН2А steel, the maximum temperature limit val-ues in the treatment zone were established for three moments of time that corresponded to the laser pulse fronts at the three points in the finite element model. A comparison was made between the parameters ob-tained from optimization and those derived from finite element modelling. When determining temperatures, the maximum percentage error of the results obtained via the genetic algorithm did not exceed 3.5 %

Heavy metals in tailings and soils in the Pb-Zn mining areas of North-west Türkiye and health risk evaluations

Improper mining waste and tailing management in Pb-Zn mining areas (Balya and Koru) in the north-west Türkiye have not been researched sufficiently. Accordingly, concentrations of heavy metal were determined in mine tailing and soils taken from Balya and Koru, and a health risk evaluation caused by heavy metals was performed. Average Cd, Cr, Cu, Mn, Ni, Pb, and Zn concentrations in mine tailings in Balya are 35.2, 17.8, 354.7, 1735, 10, 10089, 3730 mg kg-1 and these values were determined as 9.9, 8.9, 101.5, 1308, 4.5, 1871, 1375 mg kg-1 in the tailings in Koru, respectively. The concentrations of heavy metals in the soil samples taken from both Balya and Koru were determined to be lower. The evaluation of heavy metals’ health risks was performed according to both non-carcinogenic and carcinogenic effects. The primary route of heavy metals in adults and children has been determined by oral intake. For both children and adults, the order of the carcinogenic effects of heavy metals in mine tailings and soils in Balya and Koru was Cd > Pb > Ni > Cr. As the carcinogenic risk values of Cd and Pb for adults and children in mine tailing and soils in Balya were above the limit value, the children’s Cd carcinogenic risk values were found above the limit value in mine tailing and soils in Koru. The mining area in both Balya and Koru poses a risk to human health since it is close to settlements.

Bifunctional Electrocatalysts for Overall and Hybrid Water Splitting.

Electrocatalytic water splitting driven by renewable electricity has been recognized as a promising approach for green hydrogen production. Different from conventional strategies in developing electrocatalysts for the two half-reactions of water splitting (e.g., the hydrogen and oxygen evolution reactions, HER and OER) separately, there has been a growing interest in designing and developing bifunctional electrocatalysts, which are able to catalyze both the HER and OER. In addition, considering the high overpotentials required for OER while limited value of the produced oxygen, there is another rapidly growing interest in exploring alternative oxidation reactions to replace OER for hybrid water splitting toward energy-efficient hydrogen generation. This Review begins with an introduction on the fundamental aspects of water splitting, followed by a thorough discussion on various physicochemical characterization techniques that are frequently employed in probing the active sites, with an emphasis on the reconstruction of bifunctional electrocatalysts during redox electrolysis. The design, synthesis, and performance of diverse bifunctional electrocatalysts based on noble metals, nonprecious metals, and metal-free nanocarbons, for overall water splitting in acidic and alkaline electrolytes, are thoroughly summarized and compared. Next, their application toward hybrid water splitting is also presented, wherein the alternative anodic reactions include sacrificing agents oxidation, pollutants oxidative degradation, and organics oxidative upgrading. Finally, a concise statement on the current challenges and future opportunities of bifunctional electrocatalysts for both overall and hybrid water splitting is presented in the hope of guiding future endeavors in the quest for energy-efficient and sustainable green hydrogen production.

The Human Crisis Revisited: Albert Camus and Climate Rebellion

ABSTRACT Faced with the absurdity of continued climate inaction, more people are becoming morally outraged about the projections of human suffering and loss due to global warming impacts. This article draws from the work of Albert Camus to examine human responses to absurdity through rebellion and how this can be applied to understand the notion of climate rebellion. Focusing on Camus’ works The Rebel and The Plague, as well as his speech “The Human Crisis”, I examine the conditions of climate injustice that present the grounds for climate rebellion, what becoming a climate rebel might mean, the importance of solidarity in climate rebellion, and lastly how Camus’ value of limitation might inform ethical responses to minimize climate-related harm.

A Comprehensive Mapping of the Coconut Value Chain Actors in Western Tamil Nadu, India

The coconut industry in Western Tamil Nadu, India, epitomizes the intricate interplay of actors and activities within the agricultural value chain. Despite India's prominent stature as the leading coconut producer globally, challenges persist, including price disparities and limited value addition. This study investigates the coconut value chain in Western Tamil Nadu, mapping its actors and activities to elucidate opportunities for enhancing efficiency and sustainability. Employing a multi-stage sampling technique, data were collected from 300 coconut farmers and various stakeholders. Six value chains were identified, encompassing domestic, processing, and export markets. Primary actors, including farmers, harvest contractors, commission agents, wholesalers, retailers, processors, farmer producer companies (FPCs), and exporters, were analyzed in terms of their roles and activities. Results highlight the significance of value chain mapping in understanding market dynamics and optimizing resource allocation. Channel III, facilitated by FPCs, emerged as a promising avenue for reducing costs and enhancing market efficiency. This study emphasizes the importance of informed decision-making and strategic interventions for fostering a sustainable and vibrant coconut industry in Western Tamil Nadu and beyond.

Provincial-scale Soil As Migration and Transformation and Rice Safe Planting Zoning: A Case Study of Guizhou Province

To explore the distribution characteristics of paddy soil and rice AS content, as well as the health risks of rice consumption, and to evaluate the safe planting ability of rice, 209 paddy soil samples and 1 567 groups of paddy soil-rice samples were collected, their As content and basic soil physical and chemical properties were determined, and the single-factor pollution index method was used to evaluate the pollution degree of the samples. The results showed that:① the soil of paddy fields in Guizhou Province was mainly neutral, and its fertilizer retention capacity and organic matter content were above the medium level, and the soil was relatively fertile. The range of ω(As) in paddy soil was 0.042-91.75 mg·kg-1, the geometric mean was 10.03 mg·kg-1, and the cumulative effect of paddy soil As was lower than that of natural soil As (P<0.05) by independent sample T. Compared with the screening value (0.2 mg·kg-1) of the Soil Pollution Risk Management and Control Standard for Agricultural Land (GB 15618-2018), the excess rate of soil samples was 15.37%. ② The ω (As) range of rice grain samples was 0.001-0.937 mg·kg-1, the geometric average value was 0.108 mg·kg-1, 10.21% of the rice grain samples exceeded the limit value of "Limit of Contaminants in Food (trial)" (GB 2762-2022), and the locations where the exceedances are mainly found are in the central and northern parts of Qiannan Prefecture, as well as around industrial and mining activity zones in the southern counties and districts of Zunyi. ③ As ingested through rice posed non-carcinogenic risk and carcinogenic risk for adults and children, and the impact on children was greater than that of adults. There is no strict control area for safe rice planting in Guizhou Province, and rice can be safely planted.

Theory and Empirical Analysis of Bridge Load Limitation Under the Action of Typical Heavy-Duty Vehicles

Abstract With the continuous growth of transportation demands, in-service highway bridges face greater challenges in their long-term operational lifespans, and bridge collapse accidents caused by vehicle overloading occur from time to time. Additionally, under the influence of loads and environmental factors, various wear patterns inevitably lead to degraded reinforced concrete bridges. In view of this problem, it is reasonable and feasible to limit the vehicle loads passing over highway bridges, and the key basis for limitation is determining the load limit value of a bridge. To determine a reasonable load limit value of a bridge, this paper has carried out the following research: Based on a classification of vehicle types, this paper explores the load parameters of several heavy-duty vehicles with large traffic volumes through traffic flow information and summarizes the load spectra of typical heavy-duty vehicles. On the basis of the theory of structural reliability, a method for determining the limit load of bridges is proposed. Given a structural target reliability index, the theoretical load limit value of a bridge can be calculated. To ensure the rationality of the theory of bridge load limit value, by relying on the engineering example, the theoretical load limit value is calculated. By comparing actual bridge load test data with the finite element model results, the rationality of the bridge load limiting theory is verified. Finally, the paper notes that it is safer and more reliable to define the load limit value according to the bending stress state for bridges.

Finite Element Analysis and Fatigue Test of INTEGRA Dental Implant System.

The study involved numerical FEA (finite element analysis) of dental implants. Based on this, fatigue tests were conducted according to the PN-EN 14801 standard required for the certification of dental products. Thanks to the research methodology developed by the authors, it was possible to conduct a thorough analysis of the impact of external and internal factors such as material, geometry, loading, and assembly of the dental system on the achieved value of fatigue strength limit in the examined object. For this purpose, FEM studies were based on identifying potential sites of fatigue crack initiation in reference to the results of the test conducted on a real model. The actions described in the study helped in the final evaluation of the dental system design process named by the manufacturer as INTEGRA OPTIMA 3.35. The objective of the research was to identify potential sites for fatigue crack initiation in a selected dental system built on the INTEGRA OPTIMA 3.35 set. The material used in the research was titanium grade 4. A map of reduced von Mises stresses was used to search for potential fatigue crack areas. The research [loading] was conducted on two mutually perpendicular planes positioned in such a way that the edge intersecting the planes coincided with the axis of the system. The research indicated that the connecting screw showed the least sensitivity (stress change) to the change in the loading plane, while the value of preload has a significant impact on the achieved fatigue strength of the system. In contrast, the endosteal implant (root) and the prosthetic connector showed the greatest sensitivity to the change in the loading plane. The method of mounting [securing] the endosteal implant using a holder, despite meeting the standards, may contribute to generating excessive stress concentration in the threaded part. Observation of the prosthetic connector in the Optima 3.35 system, cyclically loaded with a force of F ≈ 300 N in the area of the upper hexagonal peg, revealed a fatigue fracture. The observed change in stress peak in the dental connector for two different force application surfaces shows that the positioning of the dental system (setting of the socket in relation to the force action plane) is significantly decisive in estimating the limited fatigue strength.

Reviewing Outcomes and Complications with the Use of Mesh in Breast Reduction Surgery.

Reduction mammoplasty is a common reconstructive and esthetic procedure with variable long-term outcomes regarding breast shape, projection, and nipple-areolar complex. One common complaint is recurrent breast ptosis, which may be mitigated by sufficient support of the inferior pole. This review will look at the effects of mesh in mitigating postoperative ptosis following reduction mammoplasty. A comprehensive review of the literature was performed using the PubMed database. Manuscripts that provided data with respect to the effects of mesh on cosmetic outcomes, patient-reported outcomes, complications, and surveillance were utilized. Six studies with a total of 634 patients were included in this review. There is limited evidence to support a cosmetic benefit with the use of mesh in reduction mammoplasty patients. While subjective satisfaction was demonstrated in one paper, few others had objective measurements of the impact of mesh. Complications included infection, skin necrosis, and loss of nipple sensation. Mammography was found to not be affected by mesh placement. The use of mesh during reduction mammoplasty is a relatively modern innovation that does not appear to have a significantly different risk profile than that of traditional reduction procedures. There is limited cosmetic value based on currently available data. More objective future analysis is necessary in order to justify the use of mesh in reduction mammoplasty for its claimed cosmetic benefits. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine Ratings, please refer to Table of Contents or online Instructions to Authors www.springer.com/00266.

Modelling the Impregnation of a Pressure-Tight Casting

AbstractPressure tightness is important for many die-cast aluminium castings, but the interconnected porosity formed in the aluminium alloy high-pressure die castings (HPDC) can form a network connecting several surfaces of the casting, especially as a result of machining after casting. The resulting potential leakage path can be imagined as a series of discontinuities varying in size over wide limits, where voids of different volumes are connected by channels of smaller cross section. Although vacuum impregnation is often used to ensure pressure-tightness is a robust technology, cavity systems through the casting can still cause leakage after impregnation. This study addresses the issues of the impregnation of discontinuities with a complex geometry. The elementary part of a complex cavity geometry consists of a cavity and a capillary channel. We estimated the limited permeability of the capillary section using a mathematical model based on the Hagen–Poiseuille equation. The calculation results prove that the degree of filling of the cavity with a capillary section is basically a function of the geometrical characteristics of the cavity, primarily the radius of the capillary. If the cavity system also contains a section with a diameter of less than 28 μm, impregnation does not necessarily ensure the gas tightness of the casting. Depending on the radius of the capillary, the impregnation of a cavity of a given volume and connected to the surface through a capillary section of a given length can produce three different results. Above a certain capillary radius, filling is complete, below a certain capillary radius only the capillary itself will contain resin, and between the two limit values, the partial impregnation of the cavity is expected but the capillary section is not filled.

Analysis of the Cooling Modes of the Lining of a Ferroalloy-Casting Ladle

Analysis of the Cooling Modes of the Lining of a Ferroalloy-Casting Ladle

Ultrahigh power factor and excellent solar efficiency in two-dimensional hexagonal group-IV–V nanomaterials

The mesmerizing physical properties of two-dimensional (2D) nanomaterials have resulted in their enormous potential for high-power solar energy conversion and long-term stability devices. The present work systematically investigated the fundamental properties of monolayered 2D group-IV–V materials using a combined approach of first-principles calculations and Boltzmann transport theory, specifically the thermoelectric and optical properties, for the first time. The structural and lattice dynamics analysis disclosed the energetic, dynamical, and mechanical stabilities of 17 out of 25 considered materials. The electronic properties’ calculation shows that all the stable materials exhibit a semiconducting nature. Additionally, the energy–momentum relation in a few systems reveals the quartic Mexican-hat-like dispersion in their valence band edges. Owing to the larger depth of Mexican-hat dispersion and the larger height of density step function modes, the hole carrier mobilities of SnN (761.43 m2/Vs), GeN (422.80 m2/Vs), and SiN (108.90 m2/Vs) materials were found to be significantly higher than their electron mobilities at room temperature. The achieved high Seebeck coefficient and electrical conductivity at room temperature result in excellent thermoelectric power factors for GeN (3190 mW/mK2), SiN (1473 mW/mK2), and CAs (774 mW/mK2) materials, manifesting their potential for thermoelectric devices. Further, the calculated optical and solar parameters demonstrate an exceptionally high value (27.25%) of theoretical limits of power conversion efficiency for the SnBi material, making it a suitable candidate as a light-absorbing material in solar cell devices. The present theoretical work filters out the potential 2D group-IV–V materials for solar and heat energy-harvesting devices.