Light Source Research Articles

Recent Advances in Thermally Activated Delayed Fluorescence-Based Organic Afterglow Materials.

Thermally activated delayed fluorescence (TADF)-based materials are attracting widespread attention for different applications owing to their ability of harvesting both singlet and triplet excitons without noble metals in their structures. As compared to the conventional fluorescence and room-temperature phosphorescence pathways, TADF originates from the reverse intersystem crossing process from the excited triplet state (T1) to the singlet state (S1). Therefore, TADF emitters enabling activated and long lifetime T1 excitons are potential candidates for generating long-lived afterglow emission, an effect that can still be observed for a while by the naked eye after the removal of the excitation light source. Recently, TADF-based organic afterglow materials featuring high photoluminescence quantum yields and long lifetimes above 100 ms under ambient conditions, have emerged for advanced information security, high-contrast biological imaging, optoelectronic devices, and intelligent sensors, whereas the related systematic review is still lacking. Herein, the recent progress in TADF-based organic afterglow materials is summarized and an overview of the photophysical mechanism, design strategies, and the performances for relevant applications is given. In addition, the challenge and perspective of this area are given at the end of the review.

Bottom Electrode Modification Enables Efficient and Bright Silicon-Based Top-Emission Perovskite Light-Emitting Diodes.

The integration of perovskites with mature silicon platform has emerged as a promising approach in the development of efficient on-chip light sources and high-brightness displays. However, the performance of Si-based green perovskite light-emitting diodes (PeLEDs) still falls significantly short compared to their red and near-infrared counterparts. In this study, it is revealed that the high work function Au, widely employed in Si-based top-emission PeLEDs as the reflective bottom electrode, exhibits considerably lower reflectivity in the green spectrum than in the longer wavelengths. Consequently, Ag electrode is introduced to replace Au to enhance the green light reflectivity, and the ultrathin MoO3 and self-assembled monolayers (SAMs) are sequentially deposited for surface modification. These results indicate that the MoO3 layer removes the energy barrier at Ag/polymer hole transport layer interface, enhancing the hole injection efficiency; while the SAMs firmly anchor onto the MoO3 layer, effectively preventing interfacial defect formation. Benefited from this organic/inorganic dual-layer modification strategy, Si-based green PeLEDs with an impressive peak external quantum efficiency of 18.2% and a maximum brightness of 81931 cd m-2 are successfully fabricated, on par with those of the red and near-infrared counterparts. This achievement marks an advancement in developing high-performance Si-based PeLEDs with full-spectrum output.

Asymmetric influence of the amplitude-dependent tune shift on the transverse mode-coupling instability

At the 3 GeV ring of the MAX IV Laboratory, a fourth-generation ring-based synchrotron light source, an asymmetric influence of the sign of the amplitude-dependent tune shift (ADTS) on the transverse mode-coupling instability has been observed. Measurements of the instability, in dedicated single-bunch experiments at low chromaticity, revealed a significant dependence of the dynamics of the instability above threshold on the sign of the ADTS. While for a negative sign of the ADTS, the crossing of the instability does not lead to a loss of beam current, a positive sign results in the loss of 40% or more of the beam current at the threshold. In order to investigate the observed asymmetry, the systematic measurement of beam dynamics above the threshold has been conducted in combination with particle tracking simulations with 2 and theoretical calculations of the Landau damping due to the ADTS. The findings point toward an influence of the Landau damping in combination with the low synchrotron frequency, which indicates that this effect could become relevant in the future low-emittance electron storage rings. Published by the American Physical Society 2024

Characteristic of temporal light modulation reference meter and standard light source for calibration and verification

Abstract The measurement of the temporal light modulation (TLM) of a light source is gaining increasing importance owing to its detrimental effects on human vision and health. To establish traceability in TLM measurements, the National Institute of Metrology, China (NIM), established a TLM reference meter (TLMM) and standard TLM light source (STLS) for calibration and verification services. The TLMM and STLS employ detector- and source-based approaches, respectively, to define the standards for TLM quantities. The TLMM rapidly acquires light waveform data from the TLM light sources and calculates corresponding TLM quantities. Frequency calibration result is with an expanded uncertainty of 1 × 10−5, frequency response function is almost flat in range of 1 kHz–25 kHz, and response time is less than 8 × 10−6 s. The electrical noise was evaluated at approximately 1000:1–5000:1. The STLS generates an arbitrary TLM waveform by converting the virtual waveform into an actual LED output light waveform. For the frequency response function, the relative amplitude decreased by 1% with a frequency of 15 kHz, and response time was less than 5 × 10−6 s. The linearity of the frequency dependency was studied with ratio varied by approximately 0.19% when the periodic triangle excitation in frequency band from 1 Hz to 1 kHz. Experimental comparisons demonstrated that TLM quantities (frequency, percentage flicker, flicker index, short-term flicker severity P st LM , and stroboscopic effect visibility measure ( SVM )) are consistent between the TLMM and STLS devices on 14 typical TLM waveforms. For P st LM , most of the deviations were in the range of −0.019–0.079 (except for one with 0.182). For SVM , most of the deviations were in the range of −0.001–0.003 (except for one with 0.014).

High-speed 3D measurement using the kinoform array and light source shift.

A new, to the best of our knowledge, fringe projector using the kinoform is proposed in this Letter. The kinoform array makes the hologram easy to manufacture, and the phase shift is realized by light source shift. The fringes can be shifted at a high speed due to the high-speed switch of the light source. An active binocular 3D measurement system using the proposed projector is demonstrated, and a binocular matching algorithm from coarse to fine using a laser speckle and fringe phase is proposed. Three laser diodes are adopted as light sources, and the three-step phase-shifting is achieved. The dimension of the projector is 30 mm × 26 mm × 12 mm and the switching speed is up to 1.5 kHz. The 3D measurement speed reaches 70 fps in the experiment.

Green upgrading of SPring-8 to produce stable, ultrabrilliant hard X-ray beams.

SPring-8-II is a major upgrade project of SPring-8 that was inaugurated in October 1997 as a third-generation synchrotron radiation light source. This upgrade project aims to achieve three goals simultaneously: achievement of excellent light source performance, refurbishment of aged systems, and significant reduction in power consumption for the entire facility. A small emittance of 50 pm rad will be achieved by (1) replacing the existing double-bend lattice structure with a five-bend achromat one, (2) lowering the stored beam energy from 8 to 6 GeV, (3) increasing the horizontal damping partition number from 1to 1.3, and (4) enhancing horizontal radiation damping by installing damping wigglers in long straight sections. The use of short-period in-vacuum undulators allows ultrabrilliant X-rays to be provided while keeping a high-energy spectral range even at the reduced electron-beam energy of 6 GeV. To reduce power consumption, the dedicated, aged injector system has been shut down and the high-performance linear accelerator of SACLA, a compact X-ray free-electron laser (XFEL) facility, is used as the injector of the ring in a time-shared manner. This allows the simultaneous operation of XFEL experiments at SACLA and full/top-up injection of the electron beam into the ring. This paper overviews the concept of the SPring-8-II project, the system design of the light source and the details of the accelerator component design.

Preparation and identification of a fluorescent probe with CsPbBr3perovskite quantum dots and CD44v6 specific peptide for gastric cancer imaging.

Since the sensitivity and accuracy of traditional detection for early gastric cancer diagnosis are still insufficient, it is significant to continuously optimize the optical molecular imaging detection technology based on an endoscopic platform. The signal intensity and stability of traditional chemical fluorescent dyes are low, which hinders the clinical application of molecular imaging detection technology. This work developed a probe based on perovskite quantum dots (PQDs) and peptide ligands. By utilizing CsPbBr3perovskite PQDs modified by azithromycin (AZI), combined with the specific polypeptide ligand of CD44v6, a gastric cancer biomarker, the perovskite-based probe (AZI-PQDs probe) which can specifically identify gastric cancer tumor was prepared. Owing to the high photoluminescence quantum yield of CsPbBr3PQDs, the naked eye can observe the imaging under the excitation of the hand-held ultraviolet light source. AZI-PQDs probe can accurately identify gastric cancer cells, tissues, and xenograft models with experiments ofex vivoandin vivofluorescence imaging detection. It also exhibited low toxicity and immunogenicity, indicating the safety of the probe. This work provides a probe combined with cancer specificity and a reliable fluorescent signal that has the potential for application in gastric cancer optical molecular imaging.

Color Ranges and Distribution of Human Teeth: A Prospective Clinical Study.

This study investigated the in vivo color range of human teeth using a research-grade noncontact spectroradiometer, analyzing the effects of gender, age, ethnicity, and lifestyle factors, including diet, smoking, and oral hygiene. A total of 1004 participants were recruited at two research sites and stratified by gender, age, and ethnicity, and data on their dietary and oral habits were collected. Noninvasive color measurements of an upper central incisor were performed using a spectroradiometer and a fiber-coupled Xe-Arc light source. Color differences were computed using the CIELAB and CIEDE2000 color difference formulas, statistically analyzed, and interpreted through comparisons with 50:50% perceptibility (PT) and acceptability (AT) thresholds for dentistry. CIELAB and CIEDE2000 color coordinate values varied significantly. Female teeth appeared lighter and less yellow than men's. Age correlated with darker, more chromatic teeth, stabilizing only after Age 46. Significant ethnic differences were observed, particularly between African-American and Asian participants. Coffee consumption impacted teeth yellowness and chromaticity, while tea had no significant effect. Frequent tooth brushing led to lighter teeth, and tooth whitening considerably influenced color, emphasizing the effect of cosmetic dental treatments. Smoking showed minimal impact, with slight discoloration noted among light smokers compared to nonsmokers. Color coordinate values by gender, age, and ethnicity exhibited statistically significant differences and, in most cases, noticeable color differences. With exceptions, the dietary/oral habits of the patient had a significant impact on the color of human teeth. The findings from this study provide detailed information and understanding of the color range and distribution of human teeth, which can help enhance the esthetic outcome of dental care and, consequently, the patient's satisfaction.

Intraocular lens simulator using computational holographic display for cataract patients.

To develop and validate a holography based vision simulator for the demonstration of expected postoperative vision corresponding to monofocal and multifocal intraocular lenses (IOL) to cataract patients before surgery. An artificial eye model is used to measure the optical performance of different IOL types. The resultant aberrations and degradations are then modeled using phase holograms and shown to subjects on a holographic display. We measure the contrast and resolution loss, halos around the light sources, and point spread function (PSF) corresponding to three different IOLs. We tested the holography based vision simulator on 13 healthy subjects and 6 cataract patients. Monofocal, bifocal, and trifocal IOLs exhibited a contrast decrease of 5%, 42%, and 45% and a resolution limit of 4.49, 4.00, and 4.00 lp/mm (using 0.05 MTF criteria), respectively. Monofocal IOLs have the best resolution and contrast at the optimal focus distance, and multifocal lenses offer extended depth-of-field but exhibit prominent halos and reduced contrast/resolution. We confirmed that the visual functions of IOLs could be successfully modeled using phase holograms and simulated using a holographic display without using a physical IOL. Patients can experience the effects of different IOL options prior to surgery, which helps with IOL selection, expectation management, and patient satisfaction.

High-efficiency second-harmonic generation in reverse-polarization dual-layer lithium niobate waveguides.

Second-harmonic (SH) generation is an important way to generate short-wavelength light sources. Thin-film lithium niobate (TFLN) resonators and waveguides featuring tight light confinement are flexible to realize mode- or quasi-phase-matching (MPM or QPM) and thus efficient SH generation. Here, we report an efficient SH with an absolute conversion efficiency of 45% in a reverse-polarized double-layer TFLN waveguide. Such a high conversion efficiency without periodic poling was realized with the pump of 67 mW in the 1550 nm band, benefiting from the employment of the largest nonlinear coefficient d33 and the significant nonlinear interaction of the fundamental transverse electric (TE) mode and the first-order TE mode in the vertical direction. This work paves the way toward on-chip integrated nonlinear optics in terms of harmonic generation and quantum light sources across the telecom and visible bands.

Gradient Hole Injection Inducing Efficient Exciton Recombination in Blue (475 nm) Perovskite QLEDs.

Perovskite quantum dots (QDs) are emerging as excellent light sources for light-emitting diodes (LEDs). However, the performance of blue perovskite QD-based LEDs (QLEDs) still lags behind that of red and green counterparts, which is hindered by blue perovskite QDs with broad bandgaps that tend to increase nonradiative recombination. Here, we designed a gradient energy for hole injection utilizing multiple hole injection layers (HTLs) combined with carbazole-based small-molecule modification to reduce the hole injection barrier between HTLs and QD layers and improve the hole injection efficiency, realizing efficient exciton recombination in blue perovskite QLEDs. Moreover, the QD film on the designed HTLs demonstrates a lower surface roughness and improved photoluminescence properties. The optimized blue CsPbCl3-xBrx QLEDs exhibit an impressive external quantum efficiency of 20.7% with an electroluminescence peak at 475 nm and a turn-on voltage of 2.6 V, representing the state-of-the-art for blue perovskite LEDs emitting in the range of 460-480 nm.

Single-Shot Fringe Projection Profilometry Based on LC-SLM Modulation and Polarization Multiplexing

Fringe projection profilometry (FPP) is extensively utilized for the 3D measurement of various specimens. However, traditional FPP typically requires at least three phase-shifted fringe patterns to achieve a high-quality phase map. In this study, we introduce a single-shot FPP method based on common path polarization interferometry. In our method, the projected fringe pattern is created through the interference of two orthogonal circularly polarized light beams modulated by a liquid crystal spatial light modulator (LC-SLM). A polarization camera is employed to capture the reflected fringe pattern, enabling the simultaneous acquisition of four-step phase-shifting fringe patterns. The system benefits from advanced anti-vibration capabilities attributable to the common path self-interference optical path design. Furthermore, the utilization of a low-coherence LED light source results in reduced noise levels compared to a laser light source. The experimental results demonstrate that our proposed method can yield 3D measurement outcomes with high accuracy and efficiency.

Improving the efficiency of thermal insulation of window panes—the use of transparent thin-layer insulation coverings filled with nanostructures

AbstractThe article discusses experimental studies on the thermal conductivity of a transparent thermal insulation layer (film) applied to a window pane. The research was conducted using a measurement cube known as the "Hot Box" method. The examined film was made based on a polymer matrix with metallic inclusions. The insulating layer of the film allows for the transmission and blocking of light—UV infrared radiation. In the studies, a 100 W bulb was used as the source of infrared radiation (light source), placed at the central point of the measurement cube "Hot Box". To estimate the heat transport conditions, temperature distributions on the internal and external surfaces of the examined window pane with the applied transparent coating (film) were measured. Based on the temperature distribution data, the thermal conductivity coefficient of the applied transparent coating on the pane was estimated.

Efficient Environment Map Rendering Based on Decomposition

AbstractThis paper presents an efficient environment map sampling algorithm designed to render high‐quality, low‐noise images with only a few light samples, making it ideal for real‐time applications. We observe that bright pixels in the environment map produce high‐frequency shading effects, such as sharp shadows and shading, while the rest influence the overall tone of the scene. Building on this insight, our approach differs from existing techniques by categorizing the pixels in an environment map into emissive and non‐emissive regions and developing specialized algorithms tailored to the distinct properties of each region. By decomposing the environment lighting, we ensure that light sources are deposited on bright pixels, leading to more accurate shadows and specular highlights. Additionally, this strategy allows us to exploit the smoothness in the low‐frequency component by rendering a smaller image with more lights, thereby enhancing shading accuracy. Extensive experiments demonstrate that our method significantly reduces shadow artefacts and image noise compared to previous techniques, while also achieving lower numerical errors across a range of illumination types, particularly under limited sample conditions.

Deep Learning‐Based Variational Autoencoder for Classification of Quantum and Classical States of Light

AbstractAdvancements in optical quantum technologies have been enabled by the generation, manipulation, and characterization of light, with identification based on its photon statistics. However, characterizing light and its sources through single photon measurements requires efficient detectors and longer measurement times to obtain high‐quality photon statistics. Here, a deep learning‐based variational autoencoder (VAE) method is introduced for classifying single photon added coherent state (SPACS), single photon added thermal state (SPATS), and mixed states between coherent and SPACS as well as between thermal and SPATS of light. The semi‐supervised learning‐based VAE efficiently maps the photon statistics features of light to a lower dimension, enabling quasi‐instantaneous classification with low average photon counts. The proposed VAE method is robust and maintains classification accuracy in the presence of losses inherent in an experiment, such as finite collection efficiency, non‐unity quantum efficiency, finite number of detectors, etc. Additionally, leveraging the transfer learning capabilities of VAE enables successful classification of data of any quality using a single trained model. It is envisioned that such a deep learning methodology will enable better classification of quantum light and light sources even in poor detection.

Ultra-broadband emission from Mg7Ga2GeO12:Ni2+,Cr3+ phosphor spanning the NIR I–III regions for spectroscopy applications

Ultra-broadband near-infrared (NIR) lighting sources covering NIR Ⅰ to III regions are pivotal components for NIR spectroscopy devices. However, achieving ultra-broadband and efficient emission covering the entire NIR Ⅰ to III regions remains a significant challenge. To address this, we selected Mg7Ga2GeO12 as host material to realize ultra-broadband NIR emission. Density functional theory calculations on formation energies confirmed the feasibility of doping both Ni2+ and Cr3+ within Mg7Ga2GeO12. Band structure calculations reveal a significantly reduced band gap upon the doping of Ni2+. Following that, we synthesized Mg7Ga2GeO12:Ni2+ through conventional solid-state-reaction method. This phosphor exhibits broadband NIR emission with a full-width-at-half-maximum of 377 nm in the range of NIR II ∼ III (1100–2100 nm). To further enhance the emission efficiency, we co-doped Mg7Ga2GeO12:Ni2+ phosphor with Cr3+. This co-doping strategy not only dramatically enhances the Ni2+ emission intensity, but also extends the lower limit of emission band to 600 nm. However, a spectral gap around 1150 nm remains between Cr3+ and Ni2+ emission centers. To bridge this spectral gap, we employed LiScSiO4:Cr3+ phosphor alongside Mg7Ga2GeO12:Ni2+,Cr3+ phosphor to fabricate a phosphor converted LED (pc-LED) with ultra-broadband NIR emission covering entire NIR Ⅰ to III regions. By utilizing this pc-LED as the lighting source for NIR spectral detection, multiple organic functional group signals can be identified simultaneously in NIR II and III bands from 1000 to 2100 nm. The performance of such an NIR pc-LED not only confirms the application potential of Mg7Ga2GeO12:Ni2+,Cr3+ phosphor in non-destructive spectral analysis but also underscores the feasibility of combining two phosphors to achieve ultra-broadband NIR pc-LEDs, rendering them suitable to be lighting sources for portable spectrometers.

Long-term noninvasive cardiac monitoring via Neutralized interfacial design for noise-suppressed near-infrared organic photodetectors

Organic photodetectors (OPDs) are the prime candidates for realizing commercial photoplethysmography (PPG) sensors in the future, although their performance and stability limitations remain as challenges. This study presents a strategy for fabricating high-precision, long-term, sustainable OPDs for non-invasive cardiac monitoring. In this work, the use of appropriate amounts of heterocyclic 1,3-diazoles (solid surfactants) enhances the morphology of PEDOT:PSS films and optimizes its energy level alignment, thus directly reducing the leakage current noise and improving the stability of the OPD. The OPDs with 0.5 wt% heterocyclic 1,3-diazole demonstrate enhanced dark current suppression and detectivity enhancement in the photoconductive and self-powered modes. Improved charge recombination dynamics and optimal resistance ratios lead to better performance of the champion device under low-intensity illumination. The champion device yields a more precise Photoplethysmography (PPG) signal under normal and exercise conditions when using a near-infrared light source, and it maintains a PPG signal intensity of more than 90 % after 315 days (7560 h) of storage in a nitrogen atmosphere. Optimized PPG sensors based on flexible substrates maintain signal intensity after seven days of air storage. The low hysteresis behavior also verifies that the optimized device has higher driving stability. High-reliability, high-validity accelerated photoplethysmography (APG) demonstrated that the champion PPG sensor would be used for accurate cardiovascular diagnostics, even over an extended period.

Evaluation of Bioactive Compounds and Antioxidant Activity of Green and Red Kale (Brassica oleracea L. var. acephala) Microgreens Grown Under White, Red, and Blue LED Combinations

Microgreens have great potential for improving the nutritional value of human diets, as well as constituting a promising dietary option for preventing chronic disease. Light-emitting diodes (LEDs) are commercially used as a light source to improve the growth of microgreens, as well as nutrient and bioactive compound accumulation. Here, we provide the first report of the phenolic compound, chlorophyll and carotenoid pigment, and dietary fiber contents of red and green kale microgreens grown in a growth chamber under white LEDs combined with red or blue light. Significant differences in the response of phytocompounds between white light and its combination with blue or red LEDs were determined. These studies showed that a combination of white and blue LEDs positively influenced the accumulation of phenolic compounds, which consequently determined high antioxidant activity. On the contrary, the white LED lights were the most suitable for the accumulation of carotenoids and chlorophylls, including chlorophyll a and b, and Klason lignin. These results suggest that the use of a combination of white light with blue or red light can increase the concentration of phenolic compounds and dietary fiber in red and green kale microgreens and thus may enhance their health-promoting potential.

Upgraded front ends for SLS 2.0 with next-generation high-power diaphragms and slits.

The upgrade of the Swiss Light Source, called SLS 2.0, necessitates comprehensive updates to all 18 user front ends. This upgrade is driven by the increased power of the synchrotron beam, reduced floor space, changing source points, new safety regulations and enhanced beam properties, including a brightness increase by up to a factor of 40. While some existing front-end components are being thoroughly refurbished and upgraded for safety reasons, other components, especially those designed to tailor the new synchrotron beam, are being completely rebuilt. These new designs feature innovative and enhanced cooling systems to manage the high-power load and meet new requirements such as mechanical stability and compact footprints.

Model analysis for optical frequency comb Faraday modulation rotation spectroscopy.

Modulating the signal is a common method in spectroscopy for reducing noise. However, for broadband coherent light sources like optical frequency combs (OFCs), modulation methods typically involve the use of optical modulators, making the experimental setup cumbersome. This study proposes and successfully implements a broadband Faraday modulation rotation spectroscopy (FAMOS) method combined with an OFC. The development of this method by extending the modulation frequency of the OFC from tens of MHz down to the kHz level, effectively relaxes the stringent demands for high-speed electronics and optoelectronic devices, making modulation spectroscopy techniques more practically useful for diverse real-world environments. Moreover, through specifically designed modulation strategies, this method can effectively suppress low-frequency noise, thereby significantly improving the signal-to-noise ratio of the measurements without sacrificing measurement accuracy.