Light Absorption Research Articles

Schottky Junction Enhanced Photosynthesis of Hydrogen Peroxide by Ultrathin Porous Carbon Nitride Supported Ni Nanoparticles.

Artificial photosynthesis for high-value hydrogen peroxide (H2O2) through a two-electron reduction reaction is a green and sustainable strategy. However, the development of highly active H2O2 photocatalysts is impeded by severe carrier recombination, ineffective active sites, and low surface reaction efficiency. We developed a dual optimization strategy to load dense Ni nanoparticles onto ultrathin porous graphitic carbon nitride (Ni-UPGCN). In the absence and presence of sacrificial agents, Ni-UPGCN achieved H2O2 production rates of 169 and 4116 μmol g-1 h-1 with AQY (apparent quantum efficiency) at 420 nm of 3.14% and 17.71%. Forming a Schottky junction, the surface-modified Ni nanoparticles broaden the light absorption boundary and facilitate charge separation, which act as active sites, promoting O2 adsorption and reducing the formation energy of *OOH (reaction intermediate). This results in a substantial improvement in both H2O2 generation activity and selectivity. The Schottky junction of dual modulation strategy provides novel insights into the advancement of highly effective photocatalytic agents for the photosynthesis of H2O2.

Synthesis, spectroscopic, DFT, TD-DFT, and dyeing studies of 2-amino-3-cyano thiophene-based azo dyes on wool and nylon

This study presents the design, synthesis, and application of eight novel thiophene-based acid azo dyes featuring benzoic and salicylic acid acceptors. The synthesized dyes demonstrate versatile light absorption properties, spanning the near UV, visible, and deep red regions. Notably, the thiophene acid azo dyes containing benzoic acid acceptor unit (AB series dyes) exhibited red-shifted absorption, while their salicylic acid counterparts (SR series dyes) displayed blue-shifted absorption. The influence of increased donor strength at position 4 of the thiophene ring on absorption properties is systematically explored. Theoretical findings from Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TD-DFT) substantiate the experimental results. Moreover, the dyes are applied to wool and nylon fabrics, displaying excellent dyeability with % exhaustion properties above 70%. The dyed fabrics manifest rich shades, ranging from blue-black to deep orange. Enhanced K/S values are observed for wool-dyed fabrics in the case of SR series dyed fabrics, whereas the AB series dyes show superior results for nylon-dyed fabrics. The dyed fabrics exhibit remarkable light, wash, and rubbing fastness. Notably, nylon-dyed fabrics outperformed wool-dyed fabrics in light and wash fastness. UV protection studies reveal the fabrics’ potential to block harmful UV-A and UV-B radiation with excellent UPF ratings.

Boosting Photocatalytic CO2 Methanation through Interface Fusion over CdS Quantum Dot Aerogels.

In the field of photocatalytic CO2 reduction, quantum dot (QD) assemblies have emerged as promising candidate photocatalysts due to their superior light absorption and better substrate adsorption. However, the poor contacts within QD assemblies lead to low interfacial charge transfer efficiency, making QD assemblies suffer from unsatisfactory photocatalytic performance. Herein, a novel approach is presented involving the construction of strongly interfacial fused CdS QD assemblies (CdS QD gel) for CO2 reduction. The novel CdS QD gel demonstrates outstanding photocatalytic performance for CO2 methanation, achieving a CH4 generation rate of ≈296 µmol g-1 h-1, with a selectivity surpassing 76% and an apparent quantum yield (AQY) of 1.4%. Further investigations reveal that the robust interfacial fusion in these CdS QDs not only boosts their ability to absorb visible light but also significantly promotes charge separation. The present work paves the way for utilizing QD gel photocatalysts in realizing efficient CO2 reduction and highlights the critical role of interfacial engineering in photocatalysts.

Carbon Nanotubes as a Solid-State Electron Mediator for Visible-Light-Driven Z-Scheme Overall Water Splitting.

So-called Z-scheme systems, which typically comprise an H2 evolution photocatalyst (HEP), an O2 evolution photocatalyst (OEP), and an electron mediator, represent a promising approach to solar hydrogen production via photocatalytic overall water splitting (OWS). The electron mediator transferring photogenerated charges between the HEP and OEP governs the performance of such systems. However, existing electron mediators suffer from low stability, corrosiveness to the photocatalysts, and parasitic light absorption. In the present work, carbon nanotubes (CNTs) were shown to function as an effective solid-state electron mediator in a Z-scheme OWS system. Based on the high stability and good charge transfer characteristics of CNTs, this system exhibited superior OWS performance compared with other systems using more common electron mediators. The as-constructed system evolved stoichiometric amounts of H2 and O2 at near-ambient pressure with a solar-to-hydrogen energy conversion efficiency of 0.15%. The OWS reaction was also promoted in the case that this CNT-based Z-scheme system was immobilized on a substrate. Hence, CNTs are a viable electron mediator material for large-scale Z-scheme OWS systems.

Revolutionary composites of silver and zinc oxide nanoparticles from Hardwickia binata: Unleashing their potent antioxidant and anticancer properties

In the present of the study, was utilized the leaf extract of H. binata to synthesize Ag-ZnO nanocomposites. The nanocomposites were characterized using various techniques, including UV, FTIR, XRD and SEM-EDX. Nanocomposites are known for their promising properties, such as mechanical, thermal, electrical and optical characteristics, which have attracted significant attention from both academia and industry, resulting in active research in various fields. The introduction of silver (Ag) into the nanocomposites enabled them to exhibit UV light absorption at 366 nm, while the presence of zinc confirmed the peak at 431 nm. XRD analysis was carried out to determine the crystal structure and composition of the materials. The antibacterial properties of the Ag-ZnO nanocomposites were evaluated using the disc diffusion method, revealing the highest inhibition against the bacteria strain Bacillus subtilis (19 mm) compared to other strains. Furthermore, the nanocomposites demonstrated strong antioxidant activity against DPPH (56%), ABTS (59%) and exhibited anti-inflammatory activity (62%). Additionally, the Ag-ZnO nanocomposites showed promising anti-cancer properties, as evidenced by their effectiveness against a skin cancer cell line (A431-69%). Moreover, the nanocomposites displayed significant photocatalytic activity, resulting in a 70% degradation rate. Overall, this study successfully synthesized Ag-ZnO nanocomposites that exhibited robust antibacterial, antioxidant, anti-inflammatory and anticancer properties. These findings suggest the potential application of these nanocomposites in cancer treatment and environmental studies, particularly in dye degradation.

Regulation of Lewis acid sites on ZnO/SiW11Co for tunable photocatalytic activity toward water remediation

The function of surface acidity in catalytic reactions has been well studied in the field of conventional catalysis, nevertheless, regulating surface acidic sites and unveiling its roles during heterogeneous photocatalysis has been less frequently reported. To address this issue, we constructed a novel heterojunction photocatalyst of ZnO/SiW11Co with abundant Lewis acid sites for wastewater treatment. Under visible light irradiation, the optimal ZnO/SiW11Co was found to have the highest photocatalytic activity, achieving a degradation efficiency of 97.7% for Rhodamine B (RhB), 96.1% for tetracycline (TC), and 91.4% for methyl orange (MO). The RhB removal rate remained at 91.3% even after five cycles, indicating excellent stability and practicality of ZnO/SiW11Co. By compositing with SiW11Co, a typical polyoxometalates with unique super acid properties, ZnO/SiW11Co formed plentiful surface Lewis acid sites, as confirmed by the pyridine adsorption FT-IR and NH3-TPD. The as-formed Lewis acid sites could provide more active sites, making it easier for reactants to coordinate to the photocatalyst surface, which reduced the activation energy of photocatalytic reactions and accelerate RhB removal. Density functional theory (DFT) calculations unveiled the redistribution of electron-hole pairs, optimizing the light absorption and charge separation efficiency, which obeyed a Z-scheme mechanism. Combined active species capture experiments and electron spin resonance, •O2−, h+, and •OH were the main active substances for the photocatalytic degradation of RhB. Besides, the possible degradation pathways for RhB were analyzed using liquid chromatography-mass spectrometry (LC-MS). The work provided useful strategy for the design of high-performance photocatalysts via regulating surface Lewis acid sites toward water remediation.

Selective Photocatalytic CO2 Reduction Through Plasmonic Z‐Scheme Ag‐Bi2O3‐ZnO Heterostructures

AbstractCombination of plasmonic noble metal with semiconductors offers a promising and potential solar energy harvesting and conversion route. Herein, plasmonic Z‐scheme Ag‐Bi2O3‐ZnO (AgBZ) heterostructure is designed and synthesized via solution combustion and photo‐deposition method. Metallic Ag nanoparticles (NPs) were deposited over Bi2O3‐ZnO heterostructure; thus, they exhibit strong visible light absorption owing to surface plasmon resonance (SPR). The photocatalytic efficiency of the synthesized catalysts is investigated by the photocatalytic CO2 reduction to fuels under simulated solar light irradiation. The present system has shown an outstanding photocatalytic CO2 reduction and excellent selectivity of CO. The evolved rate of CO fuel, the amount of CO produced per unit time, over optimized Ag‐Bi2O3‐ZnO (3AgBZ) heterostructures was (96.74 μmol g−1/h) which was approximately 12 times larger than that of Bi2O3‐ZnO (0AgBZ) and 49‐fold than the quantity of evolved CO fuels over pure ZnO photocatalyst. The percentage of evolved CO to CH4 fuels over optimized Ag‐Bi2O3‐ZnO (3AgBZ) heterostructures was about 50 : 1compared to that of 2 : 3 over Bi2O3‐ZnO (0AgBZ). The great improvement and the high selectivity would be ascribed to the synergistic effect of metallic surface plasmon resonance and the Z‐scheme charges transfer system. This work would open a window to construct a single photocatalyst with different charge separation systems and excellent CO2 reduction selectivity. Finally, the mechanism for the enhanced photocatalytic performance by the synergistic effect was described and discussed.

Charge Transfer Mechanism on a Cobalt-Polyoxometalate-TiO2 Photoanode for Water Oxidation in Acid.

We constructed a photoanode comprising the homogeneous water oxidation catalyst (WOC) Na8K8[Co9(H2O)6(OH)3(HPO4)2(PW9O34)3] (Co9POM) and nanoporous n-type TiO2 photoelectrodes (henceforth "TiO2-Co9POM") by first anchoring the cationic 3-aminopropyltrimethoxysilane (APS) ligand on a metal oxide light absorber, followed by treatment of the metal oxide-APS with a solution of the polyoxometalate WOC. The resulting TiO2-Co9POM photoelectrode exhibits a 3-fold oxygen evolution photocurrent enhancement compared to bare TiO2 in aqueous acidic conditions. Three-element (Co 2p, W 4f, and O 1s) X-ray photoelectron spectroscopy and Raman spectroscopy studies before and after use indicate that surface-bound Co9POM retains its structural integrity throughout all photoelectrochemical water oxidation studies reported here. Extensive charge-transfer mechanistic studies by photoelectrochemical techniques and transient absorption spectroscopy elucidate that Co9POM serves as an efficient WOC, extracting photogenerated holes from TiO2 on the picosecond time scale. This is the first comprehensive mechanistic investigation elucidating the roles of polyoxometalates in POM-photoelectrode hybrid oxygen evolution reaction systems.

A Super-Hygroscopic Solar-Regenerated Alginate-Based Composite for Atmospheric Water Harvesting.

Global water scarcity is leading to increasingly tense competition across populations. In order to complement the largely fast-depleting fresh water sources and mitigate the challenges generated by brine discharge from desalination, atmospheric water harvesting (AWH) has emerged to support long-term water supply. This work presents a novel alginate-based hybrid material comprised of porous silico-aluminophosphate-34 (SAPO-34) as fast-transport channel medium as well as hydrophilicity and stability enhancer, and graphene-based sheets as light absorber for solar-enabled evaporation, both optimally incorporated in an alginate matrix, resulting in a composite sorbent capable of harvesting water from the atmosphere with a record intake of up to 6.85 gw gs -1. Natural sunlight is solely used to enable desorption achieving increase of the temperature of the developed network up to 60°C andresulting in release of the sorbed water, with impurities content well below the World Health Organization (WHO) upper limits. After 30 cycles of sorption and desorption, the composite hydrogel displayed unchanged water uptake and stability. This work provides an impactful perspective toward sustainable generation of water from humidity without external energy consumption supporting the emergence of alternative water production solutions.

Field comparison of dual- and single-spot Aethalometers: equivalent black carbon, light absorption, Ångström exponent and secondary brown carbon estimations

Abstract. The Aethalometer is a widely used instrument for black carbon (BC) mass concentration and light absorption coefficient (babs) measurements around the world. However, field intercomparison of the two popular models, dual-spot (AE33) and single-spot (AE31) Aethalometers, remains limited; in addition, the difference in secondary brown carbon (BrCsec) light absorption estimation between the two models is largely unknown. We performed full-year collocated AE33 and AE31 measurements in a megacity in southern China – Guangzhou. The babs values agree well between the two Aethalometers (R2 > 0.95), with AE33 / AE31 slopes ranging from 0.87 to 1.04 for seven wavelengths. AE33 consistently exhibits lower limits of detection (LODs) than AE31 for time resolutions of 2 to 60 min. The AE33 / AE31 slope for equivalent BC (eBC) was 1.2, implying the need for site-specific post-correction. The absorption Ångström exponent (AAE) obtained from different approaches does not agree very well between the two models, with the biggest discrepancy found in AAE880/950. The estimated BrCsec light absorption at 370 nm (babs370_BrCsec) was calculated using the minimum-R-squared (MRS) method for both Aethalometers. The babs370_BrCsec comparison yields a slope of 0.78 and an R2 of 0.72 between the two models, implying a non-negligible inter-instrument difference. This study highlights the high consistency in babs but less so in AAE between AE31 and AE33 and reveals site-specific correction for eBC estimation and non-negligible difference in BrCsec estimation. The results are valuable for data continuity in long-term Aethalometer measurements when transitioning from the older (AE31) to the newer (AE33) model, as anticipated in permanent global-climate and air-quality stations.

Simultaneous Li-Doping and Formation of SnO2-Based Composites with TiO2: Applications for Perovskite Solar Cells.

Tin oxide (SnO2) has been recognized as one of the beneficial components in the electron transport layer (ETL) of lead-halide perovskite solar cells (PSCs) due to its high electron mobility. The SnO2-based thin film serves for electron extraction and transport in the device, induced by light absorption at the perovskite layer. The focus of this paper is on the heat treatment of a nanoaggregate layer of single-nanometer-scale SnO2 particles in combination with another metal-dopant precursor to develop a new process for ETL in PSCs. The combined precursor solution of Li chloride and titanium(IV) isopropoxide (TTIP) was deposited onto the SnO2 layer. We varied the heat treatment conditions of the spin-coated films comprising double layers, i.e., an Li/TTIP precursor layer and SnO2 nanoparticle layer, to understand the effects of nanoparticle interconnection via sintering and the mixing ratio of the Li-dopant on the photovoltaic performance. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM) measurements of the sintered nanoparticles suggested that an Li-doped solid solution of SnO2 with a small amount of TiO2 nanoparticles formed via heating. Interestingly, the bandgap of the Li-doped ETL samples was estimated to be 3.45 eV, indicating a narrower bandgap as compared to that of pure SnO2. This observation also supported the formation of an SnO2/TiO2 solid solution in the ETL. The utilization of such a nanoparticulate SnO2 film in combination with an Li/TTIP precursor could offer a new approach as an alternative to conventional SnO2 electron transport layers for optimizing the performance of lead-halide perovskite solar cells.

Perovskite/La-BDC heterojunction enhances the performance of carbon-based perovskite solar cells

Carbon-based Perovskite Solar Cells (C-PSCs) present a promising avenue for enhancing the stability and commercialization of PSCs. However, the power conversion efficiency (PCE) of C-PSCs still lags behind that of metal-based PSCs. In this study, La-BDC (La-MOF prepared by La3+ and ligand H2BDC) has successfully synthesized using a simple hydrothermal method and then directly introduced into CH3NH3PbI3 (MAPbI3) perovskite precursor solution to prepare perovskite/La-BDC heterojunction structure with remarkable properties in light absorption, hydrophobicity, and crystallinity. By incorporating this structure, the PCE of C-PSCs with an FTO/SnO2/MAPbI3/La-BDC/Carbon architecture was effectively enhanced. The presence of CO functional group in La-BDC effectively reduced interface defects while improving carrier separation efficiency, and successfully passivated the free Pb2+ ions within the perovskite. Remarkably, the La-BDC-based device achieved a superior PCE of 14.95%, surpassing the pristine device's PCE by an impressive margin of 20.37%. Moreover, even after a 31 days period of air storage (temperature range of 15–25℃, humidity range of 15–30%), the La-BDC-based devices maintained over 90% of the initial performance, demonstrating excellent stability. This study provides a facile and effective strategy for improving the PCE and stability of C-PSCs through implementing a La-BDC heterojunction structure， and provides a new idea for MOF materials in the field of PSCs.

A Review of the Effect of Defect Modulation on the Photocatalytic Reduction Performance of Carbon Dioxide.

Constructive defect engineering has emerged as a prominent method for enhancing the performance of photocatalysts. The mechanisms of the influence of defect types, concentrations, and distributions on the efficiency, selectivity, and stability of CO2 reduction were revealed for this paper by analyzing the effects of different types of defects (e.g., metallic defects, non-metallic defects, and composite defects) on the performance of photocatalysts. There are three fundamental steps in defect engineering techniques to promote photocatalysis, namely, light absorption, charge transfer and separation, and surface-catalyzed reactions. Defect engineering has demonstrated significant potential in recent studies, particularly in enhancing the light-harvesting, charge separation, and adsorption properties of semiconductor photocatalysts for reducing processes like carbon dioxide reduction. Furthermore, this paper discusses the optimization method used in defect modulation strategy to offer theoretical guidance and an experimental foundation for designing and preparing efficient and stable photocatalysts.

Three-dimensional NiO/Ni self-floating porous composite materials for efficient solar interfacial evaporation

The scarcity of freshwater resources and energy crisis are major challenges to the progress of human society. Recently, solar-driven interfacial water evaporation utilizes photothermal conversion materials to convert solar energy into thermal energy, which possesses great application potential in seawater desalination and sewage treatment. Here, we fabricated porous nickel sponge (NSP) composite photothermal material (NiO-NSP) containing abundant NiO nanoneedles array. This in situ-grown NiO with enhanced bonding between photothermal material and substrate can be used as a solar absorber directly without consuming additional photothermal material compared to conventional coating and cladding on the carrier surface. Due to the multi-scattering induced light trapping effect of the semiconductor NiO nanoneedles array on the surface of nickel fibers, resulting in light absorption up to 96.5 %. NiO-NSP evaporators have an abundance of interconnected porous channels for water supply, which results in strong capillary action to pump water to the evaporation interface efficiently. Moreover, the highly dispersed nanoneedles array expand the evaporation surface area. Consequently, the NiO-NSP evaporator delivers an excellent evaporation rate of 1.78 kg m−2 h−1 and a photothermal conversion efficiency of 84.7 % at one sun radiation. In addition, the micron-sized porous mesh structure of NiO-NSP dissolve salt crystals and diffuse them downward into the bulk brine, exhibiting excellent salt resistance and remarkable seawater desalination stability. Moreover, NiO-NSP solar evaporators has been demonstrated to possess excellent ability to purify dye and heavy metal ion wastewater. Therefore, the NiO-NSP high-performance evaporator produced by straightforward process proved to be suitable for solar seawater desalination and wastewater purification.

Mo-BiVO4 Photocatalytically Modified Ceramic Ultrafiltration Membranes for Enhanced Water Treatment Efficiency.

This study highlights the effectiveness of photocatalytically modified ceramic ultrafiltration (UF) membranes in alleviating two major drawbacks of membrane filtration technologies. These are the generation of a highly concentrated retentate effluent as a waste stream and the gradual degradation of the water flux through the membrane due to the accumulation of organic pollutants on its surface. The development of two types of novel tubular membranes, featuring photocatalytic Mo-BiVO4 inverse opal coatings, demonstrated a negligible impact on water permeance, ensuring consistent filtration and photocatalytic efficiency and suggesting the potential for maintaining membrane integrity and avoiding the formation of highly concentrated retentate effluents. Morphological analysis revealed well-defined coatings with ordered domains and interconnected macropores, confirming successful synthesis of Mo-BiVO4. Raman spectroscopy and optical studies further elucidated the composition and light absorption properties of the coatings, particularly within the visible region, which is vital for photocatalysis driven by vis-light. Evaluation of the tetracycline removal efficiency presented efficient adsorption onto membrane surfaces with enhanced photocatalytic activity observed under both UV and vis-light. Additionally, vis-light irradiation facilitated significant degradation, showcasing the versatility of the membranes. Total Organic Carbon (TOC) analysis corroborated complete solute elimination or photocatalytic degradation without the production of intermediates, highlighting the potential for complete pollutant removal. Overall, these findings emphasize the promising applications of Mo-BiVO4 photocatalytic membranes in sustainable water treatment and wastewater remediation processes, laying the groundwork for further optimization and scalability in practical water treatment systems.

Effect of Laser Energy Density on Photophysical and Photocatalytic Properties of BiVO4 Single‐Crystal Thin Film

Effect of Laser Energy Density on Photophysical and Photocatalytic Properties of BiVO₄ Single‐Crystal Thin Film

Electric field and strain tuned the electronic and optical properties of Zr2CO2/MoSe2 van der Waals heterojunction

Two-dimensional semiconductor materials have attracted significant research interest due to their exceptional properties in various applications. Among them, transition-metal dichalcogenides and MXenes have emerged as widely used materials in photoelectronic devices due to their excellent optical and electronic properties. In this study, we investigate the electronic and optical properties of MXene/MX2 heterojunctions by employing First Principles based on density functional theory calculations on Zr2CO2/MoSe2 van der Waals heterojunctions. The results of band structure, density of states and band alignment demonstrate that the Zr2CO2/MoSe2 heterojunction is a type-II band alignment with an indirect bandgap of 0.93 eV. We further explore the impact of electric fields and strains on their electronic and optical performance. The results show that carriers can be effectively separated for designing high-performance devices in photocatalysis under electric fields ranging from −0.5 to 0.5 V/Å and biaxial strains ranging from −4% to 10 %. The formation of the Zr2CO2/MoSe2 heterojunction allows for enhanced coefficient and a broader light absorption range compared to the individual Zr2CO2 and MoSe2 components. In consequence, this study contributes to a fundamental understanding of Zr2CO2/MoSe2 heterojunctions and their potential applications in photocatalysis.

Gold core@CeO2 halfshell Janus nanocomposites catalyze targeted sulfate radical for periodontitis therapy

The sulfate radical (SO4•-), known for its high reactivity and long lifespan, has emerged as a potent antimicrobial agent. Its exceptional energy allows for the disruption of vital structures and metabolic pathways in bacteria that are usually inaccessible to common radicals. Despite its promising potential, the efficient generation of this radical, particularly through methods involving enzymes and photocatalysis, remains a substantial challenge. Here, we capitalized on the peroxidase (POD)-mimicking activity and photocatalytic properties of cerium oxide (CeO2) nanozymes, integrating these properties with the enhanced concept of plasma gold nanorod (GNR) to develop a half-encapsulated core@shell GNRs@CeO2 Janus heterostructure impregnated with persulfate. Under near-infrared irradiation, the GNRs generate hot electrons, thereby boosting the CeO2's enzyme-like activity and initiating a potent reactive oxygen species (ROS) storm. This distinct nanoarchitecture facilitates functional specialization, wherein the heterostructure and efficient light absorption ensured continuous hot electron flow, not only enhancing the POD-like activity of CeO2 for the production of SO4•- effectively, but also contributing a significant photothermal effect, disrupting periodontal plaque biofilm and effectively eradicating pathogens. Furthermore, the local temperature elevation synergistically enhances the POD-like activity of CeO2. Transcriptomics analysis, as well as animal experiments of the periodontitis model, have revealed that pathogens undergo genetic information destruction, metabolic disorders, and pathogenicity changes in the powerful ROS system, and profound therapeutic outcomes in vivo, including anti-inflammation and bone preservation. This study demonstrated that energy transfer to augment nanozyme activity, specifically targeting ROS generation, constitutes a significant advancement in antibacterial treatment.

Enhancement of solar blind full band absorption in photodetector with Ga2O3 nanopore and Al nanograting

In this paper, we presented a novel double-layer light-trapping structure consisting of nanopores and nanograting positioned on both the surface and bottom of a gallium oxide-based solar-blind photodetector. Utilizing the finite element method (FEM), we thoroughly investigated the light absorption enhancement capabilities of this innovative design. The simulation results show that the double-layer nanostructure effectively combines the light absorption advantages of nanopores and nanogratings. Compared with thin film devices and devices with only nanopore or nanograting structures, double-layer nanostructured devices have a higher light absorption, achieving high light absorption in the solar blind area.

Wintertime Diurnal Variation in Absorption Coefficient of Brown Carbon Associated with the Molecular Marker of Levoglucosan

This study investigated the aerosol particle properties and light absorption properties of brown carbon (BrC) by utilizing a seven-wavelength aethalometer, and analyzed NH4+, NO3−, SO42−, K+, K, organic carbon, elemental carbon, levoglucosan, and mannosan in PM2.5. The research was conducted in a rural area of Jeonnam, South Korea, during the winter season. In addition, the dithiothreitol assay-oxidative potential normalized to 9,10-phenanthrenequinone (QDTT-OP) was investigated throughout the study period. The absorption coefficient was found to be 2.6 to 5.6 times higher at 370 nm compared to 880 nm, suggesting the presence of light-absorbing substances in addition to black carbon (BC) particles. The estimated absorption coefficient of BrC370 was 29.9% of the total light absorption coefficient at 370 nm. Furthermore, BrC370 exhibited a strong affinity with levoglucosan while showing a weak correlation with K+, confirming the suitability of levoglucosan as a tracer for biomass burning. The QDTT-OP was 5.3 nM m−3, and highly correlated with the carbonaceous components levoglucosan and mannosan, suggesting a relatively high contribution of biomass combustion emissions to oxidative potential. Further research should be conducted to assess the health risks associated with future PM2.5 exposure related to biomass burning in the atmosphere.